Pinning,thermally activated depinning and their importance for tuning the nanoprecipitate size and density in high Jc YBa2Cu3O7−x films

YBa₂Cu₃O_7?x (Y123) films with quantitatively controlled artificial nanoprecipitate pinning centers were grown by pulsed laser deposition (PLD) and characterized by transport over wide temperature (T) and magnetic field (H) ranges and by transmission electron microscopy (TEM). The critical current density J_c was found to be determined by the interplay of strong vortex pinning and thermally activated depinning (TAD), which together produced a non-monotonic dependence of J_c on c-axis pin spacing d_c. At low T and H, J_c increased with decreasing d_c, reaching the very high J_c ～ 48 MA/cm² ～20% of the depairing current density J_d at 10 K, self-field and d_c ～ 10 nm, but at higher T and H when TAD effects become significant, J_c was optimized at larger d_c because longer vortex segments confined between nanoprecipitates are less prone to thermal fluctuations. We conclude that precipitates should extend at least several coherence lengths along vortices in order to produce irreversibility fields H_irr(77 K) greater than 7 T and maximum bulk pinning forces F_p,max(77 K) greater than 7–8 GN/m³ (values appropriate for H parallel to the c-axis). Our results show that there is no universal pin array that optimizes J_c at all T and H.     

Effect of processing temperature on the superconducting properties of acetone doped MgB2 tapes

Correlation of phase formation, critical transition temperature T_c, microstructure, and critical current density J_c with sintering temperature has been studied for acetone doped MgB₂/Fe tapes. Sintering was performed at 600–850 °C for 1 h in a flowing Ar atmosphere. High boron substitution by carbon was obtained with increasing the sintering temperature; however, the acetone doped samples synthesized at 800 °C contain large size MgB₂ grains and more MgO impurities. Incomplete reaction for the acetone doped samples heated at 600 °C result in bad intergrain connectivity. At 4.2 K, the best J_c value was achieved in the acetone doped sample sintered at 700 °C, which reached 24,000 A/cm² at 10 T and 10,000 A/cm² at 12 T, respectively. Our results indicate that the small grain size and less impurity were also important for the improvement of J_c–B properties besides the substitutions of B by C.     

A new method for estimating the critical current density of a superconductor from its hysteresis loop

The critical current density J_c of some of the superconducting samples, calculated on the basis of the Bean’s model, shows negative curvature for low magnetic field with a downward bending near H = 0. To avoid this problem Kim’s expression of the critical current density, J_c = k/(H₀ + H), where J_c has positive curvature for all H, has been employed by connecting the positive constants k and H₀ with the features of the hysteresis loop of a superconductor. A relation between the full penetration field H_p and the magnetic field H_min, at which the magnetization is minimum, is obtained from the Kim’s theory. Taking the value of J_c at H = H_p according to the actual loop width, as in the Bean’s theory, and at H = 0 according to an enhanced loop width due to the local internal field, values of k and H₀ are obtained in terms of the magnetization values M⁺(?H_min), M^?(H_min), M⁺(H_p) and M^?(H_p). The resulting method of estimating J_c from the hysteresis loop turns out to be as simple as the Bean’s method.     

Fabrication of Ti doped MgB2/Cu superconducting wires by SHS method in an unsealed furnace

Mg_0.9Ti_0.1B₂/Cu wires have been successfully synthesized by the powder-in-tube (PIT) technique combined with the self-propagating high-temperature synthesis (SHS) method in an unsealed furnace. The analysis includes the studies of the sample microstructure, phase composition, critical transition temperature T_c and critical current density J_c. The experiments show that the PIT technique combined with the SHS method is effective in reducing the Mg volatilization and oxidation. There is little reaction between Mg and Cu in the SHS process, but with the MgCu₂ and CuO phases, the reaction does occur in the inner sheath wall of the copper tube. The findings also indicate that there is little MgO in the sample. The sample has a very strong flux pinning ability at the low magnetic fields since the TiB₂ phase may prevent the growth of MgB₂ grains and lead to a favorable effect on grain refinement. The wires exhibit a high critical current density, e.g. 2.7 × 10⁵ A/cm² in the 1.0 T field at 4.2 K and 1.3 × 10⁵ A/cm² in the 2.0 T field at 4.2 K.     

Influence of Zr and Ce doping on electromagnetic properties of (Gd,Y)–Ba–Cu–O superconducting tapes fabricated by metal organic chemical vapor deposition

(Gd,Y)Ba₂Cu₃O_x tapes have been fabricated by metal organic chemical vapor deposition (MOCVD) with Zr-doping levels of 0–15 mol.% and Ce doping levels of 0–10 mol.% in 0.4 μm thick films. The critical current density (J_c) of Zr-doped samples at 77 K, 1 T applied in the orientation of H 6 c is found to increase with Zr content and shows a maximum at 7.5% Zr doping. The 7.5% Zr-doped sample exhibits a critical current density (J_c) of 0.95 MA/cm² at H 6 c which is more than 70% higher than the J_c of the undoped sample. The peak in J_c at H 6 c is 83% of that at H 6 a–b in the 7.5% Zr-doped sample which is more than twice as that in the undoped sample. Superconducting transition temperature (T_c) values as high as about 89 K have been achieved in samples even with 15% Zr and 10% Ce. Ce-doped samples with and without Ba compensation are found to exhibit substantially different J_c values as well as angular dependence characteristics.     

Critical current density in MgB2 bulk samples after co-doping with nano-SiC and poly zinc acrylate complexes

The co-doped MgB₂ bulk samples have been synthesized using an in situ reaction processing. The additives is 8 wt.% SiC nano powders and 10 wt.% [(CH₂CHCOO)₂Zn]_n poly zinc acrylate complexes (PZA). A systematic study was performed on samples doped with SiC or PZA and samples co-doped with both of them. The effects of doping and co-doping on phase formation, microstructure, and the variation of lattice parameters were studied. The amount of substituted carbon, the critical temperature (T_c) and the critical current density (J_c) were determined. The calculated lattice parameters show the decrease of the a-axis, while no obvious change was detected for c-axis parameter in co-doped samples. This indicates that the carbon was substituted by boron in MgB₂. The amount of substituted carbon for the co-doped sample shows an enhancement compared to that of the both single doped samples. The co-doped samples perform the highest J_c values, which reaches 3.3 × 10⁴ A/cm² at 5 K and 7 T. It is shown that co-doping with SiC and organic compound is an effective way to further improve the superconducting properties of MgB₂.     

AC response of YBa2Cu3O7 thin film superconductor

Low-field ac measurements of magnetic susceptibility of YBa₂Cu₃O₇ high-temperature superconducting thin film were carried out over a wide range of temperatures and ac magnetic field amplitudes. A strong field dependence of the real χ′ and imaginary χ″ components was observed. The field dependence of the imaginary component is used to extract the temperature dependence of the critical current density in the sample using the critical state model. The exponent β of the power law relation J_c ～ (1 ? T/T_c)^β was determined from ac-susceptibility data and different values were found. Experimental results are compared with predictions of some existing theoretical models describing the ac response of superconducting thin film in perpendicular ac field.     

Large transport critical currents of powder-in-tube Sr0.6K0.4Fe2As2/Ag superconducting wires and tapes

We report the achievement of transport critical currents in Sr_0.6K_0.4Fe₂As₂ wires and tapes with a T_c = 34 K. The wires and tapes were fabricated through an in situ powder-in-tube process. Silver was used as a chemical addition as well as a sheath material. All the wire and tape samples have shown the ability to transport superconducting current. Critical current density J_c was enhanced upon silver addition, and at 4.2 K, a largest J_c of ～1200 A/cm² (I_c = 9 A) was achieved for 20% silver added tapes, which is the highest in iron-based wires and tapes so far. The J_c is almost field independent between 1 T and 10 T, exhibiting a strong vortex pinning. Such a high transport critical current density is attributed to the weak reaction between the silver sheath and the superconducting core, as well as an improved connectivity between grains. We also identify a weak-link behavior from the apparent drop of J_c at low fields and a hysteretic phenomenon. Finally, we found that compared to Fe, Ta and Nb tubes, Ag was the best sheath material for the fabrication of high-performance 122 type pnictide wires and tapes.     

Critical properties of superconducting Ba1−xKxFe2As2

Magnetisation and magneto-resistance measurements have been carried out on superconducting Ba_1?xK_xFe₂As₂ samples with x = 0.40 and 0.50. From high field magnetization hysteresis measurements carried out in fields up to 16 T at 4.2 K and 20 K, the critical current density has been evaluated using the Bean critical state model. The J_C determined from the high field data is >10⁴ A/cm² at 4.2 K and 5 T. The superconducting transitions were also measured resistively in increasing applied magnetic fields up to 12 T. From the variation of the T_C onset with applied field, dH_C2/dT at T_C was obtained to be ?7.708 T/K and ?5.57 T/K in the samples with x = 0.40 and 0.50.     

Thermal and chemical expansion of mixed conducting La0.5Sr0.5Fe1−xCoxO3−δ materials

Oxygen deficiency, thermal and chemical expansion of La_0.5Sr_0.5Fe_1−xCo_xO_3−δ (x = 0, 0.5, 1) have been measured by thermogravimetry, dilatometry and high temperature X-ray diffraction. The rhombohedral perovskite materials transformed to a cubic structure at 350 ± 50 °C. The thermal expansion of the materials up to the onset of thermal reduction was 14–18 × 10^− 6 K^− 1. Above 500 °C in air (400 °C in N₂), chemical expansion contributed to the thermal expansion and the linear thermal expansion coefficients were significantly higher, 16–35 × 10^− 6 K^− 1. The chemical expansion, ε_c, showed a maximum of 0.0045 for x = 0.5 and 0.0041 for x = 1 at 800–900 °C. The normalized chemical expansion, ε_c/Δδ, was 0.036 for x = 0.5 and 0.035 for x = 1 at 800 °C. The chemical expansion can be correlated with an increasing ionic radius of the transition metals with decreasing valence state.     

Magneto-optical imaging of polycrystalline FeTe1−xSex prepared at various conditions

We have prepared high-quality polycrystalline FeTe_1?xSe_x by sintering at different temperatures and characterized their structural and magnetic properties with X-ray diffraction, magnetization measurements, and magneto-optical imaging. The intragranular J_c was estimated to be 5 × 10⁴ A/cm², which is smaller than the single crystal, but still in the range for practical applications.     

Effect of W-addition on pinning property of MgB2

The 5d transition metal W was added into the MgB₂ superconductor. The Mg, B and W were sintered at 1173 K for 30 min under H₂/Ar atmosphere in the electric furnace. The W_x(MgB₂)_1?x samples were prepared in the W concentration range of 0 ? x ? 0.05. Temperature and field dependences of magnetization were measured by the SQUID magneto-meter. The field and x dependences of J_c at 20 K were analyzed by the extended critical state model. The enhancement of J_c became maximum for the x = 0.02 sample.     

Aqueous polymer–nitrate solution deposition of YBCO films

High critical current density YBa₂Cu₃O_7?x (YBCO) films were prepared by solution deposition of aqueous non-fluorine precursors. Non-fluorine polymer-assisted deposition (PAD) processes utilizing rheology modifiers and chelating agents were used to produce 50 nm films with a critical current density (J_c) over 3 MA/cm² and 400 nm films with J_c > 1 MA/cm²_. T_c measurements indicated that films have T_c values near 90 K. The total heat treatment time to produce these high performance films was less than 4 h. Rheology modifiers such as polyvinyl alcohol (PVA) and hydroxyethyl cellulose (HEC) were used to increase the thickness of deposited films independent of the solution cation concentration. Chelating agents such as polyethylene glycol (PEG) and sucrose increased the barium ion solubility. Nitrate crystallization during deposition was controlled through rapid drying with vacuum and coating with hot solutions.     

Dissociation of dimethyl ether at high temperatures

The decomposition of dimethyl ether (CH₃OCH₃) has been investigated behind incident shock waves in a diaphragmless shock tube using laser schlieren densitometry, LS (T = 1500–2450 K, P = 57 ± 4, 125 ± 5 and 253 ± 12 Torr). The LS density gradient profiles were simulated and excellent agreement was found between the simulations and experimental profiles. Rate coefficients for CH₃OCH₃ → CH₃O + CH₃ were obtained. They showed strong fall-off, and at the lower end of the experimental temperature range are close to the low pressure limit. First order rate coefficient expressions were determined over 1500 < T < 2450 K. k_57Torr = (3.10 ± 1.0) × 10⁷⁹T^?19.03 exp(?54417/T) s^?1, k_125Torr = (1.12 ± 0.3) × 10⁸³T^?19.94 exp(?55554/T) s^?1and k_253Torr = (1.02 ± 0.3) × 10⁷³T^?17.09 exp(?51500/T) s^?1. The effect of a roaming channel for decomposition of dimethyl ether was assessed and the best agreement was obtained with 1% dissociation of DME via the roaming path.     

Inelastic neutron scattering on iron-based superconductor BaFe2(As,P)2

Inelastic neutron scattering has been performed on powder sample of an iron-based superconductor BaFe₂(As_0.65P_0.35)₂ with superconducting transition temperature (T_c) = 30 K, whose superconducting (SC) order parameter is expected to have line node. In the normal state, constant-E scan of dynamical structure factor, S(Q, E), exhibits a peak structure centered at momentum transfer Q ～ 1.20 Å^?1, corresponding to antiferromagnetic wave vector. Below T_c, the redistribution of the magnetic spectral weight takes place, resulting in the formation of a peak at E ～ 12 meV and a gap below 6 meV. The enhanced magnetic peak structure is ascribed to the spin resonance mode, evidencing sign change in the SC order parameter similar to other iron-based high-T_c superconductors. It suggests that fully-gapped s_± symmetry dominates in this superconductor, which gives rise to high-T_c (=30 K) despite the nodal symmetry.     

Time dependence of isothermal magnetization in single-phase B1 MoCy encapsulated in multiwall carbon nanocages

Isothermal magnetization M(t) in nanocrystalline single-phase B1 MoC_y encapsulated in multiwall carbon nanocages is studied within the time window of 100 < t < 5000 s. The current density J exhibits a linear logarithmic time decay. The effective activation energy U_eff increases linearly with increasing temperature T, and decreases linearly with increasing J. The behaviors of J(t), U_eff(T), and U_eff(J) can be described by the Anderson–Kim flux-creep model for thermally activated motion of uncorrelated vortices or vortex bundles over a net potential barrier U_eff. The slower relaxation of current density above the broad peak field in the isothermal magnetization curves suggests that the peak is a result of vortex dynamics.     

Effects on Jc of pinning center morphology for multiple-in-line-damage in coated conductor and bulk,melt-textured HTS

The properties of discontinuous aligned pinning centers (PCs) created by high-energy heavy-ions are compared for bulk melt-textured and coated conductor HTS. Properties of PCs, which increase J_c (pinning potential and entanglement), and negative properties which decrease J_c (e.g., decreased T_c and percolation paths) are evaluated. Mechanisms are proposed to explain the very large increases in J_c resulting from multiple-in-line-damage (MILD) compared to continuous columnar pinning centers (CCPC). In particular, a mechanism which results in fluxoid entanglement, even for parallel (unsplayed) PCs, is discussed. The same mechanism is found to also account for restoration of much of the pinning potential expected to be lost due to the gaps in MILD PCs. It also accounts for the fact that at high fluence, J_c increases as fluence is increased, instead of decreasing as expected. The very low self-field in coated conductor permits separation of the negative and positive effects of PCs. It is found that parameters developed to quantify the negative effects in bulk melt-textured YBCO, by 63 GeV U²³⁸ ions, successfully describe damage to 2.1 μm thick coated conductor by 1 GeV Ru⁴⁴ ions. Coated conductor at 77 K and self-field is generally known to have J_c about 100 times that of melt-textured YBCO. However, at 77 K and applied field of 1 T, when both forms of HTS are processed with comparable numbers of near-optimum MILD PCs, the difference in J_c is reduced to a factor of 1.3–2. Whereas J_c for melt-textured YBCO increased sharply, by a factor of up to 16.8 for high-fluence MILD PCs, J_c in coated conductor increased by a smaller factor of 2.5–3.0. Nevertheless, 2.1 μm thick coated conductor, with near-optimum MILD PCs, exhibits J_c = 543 kA/cm² at 77 K and applied field of 1.0 T, and I_c = 114 A/cm-width of conductor. This is the highest value we find in the literature. The phenomenology developed indicates that for optimum MILD PCs in coated conductor, J_c ～ 700 ± 70 kA/cm² should be achievable at 77 K, 1.0 T.     

In situ characterization of transport properties of superconducting (Cu, C)-system thin films

Transport properties of (Cu, C)Ba₂CuO_x [(Cu, C)-1201] thin films have been characterized by in situ temperature dependence of resistivity, without breaking vacuum from the deposition to the measurement. In in situ transport properties measurements, the obtained results reveal that (Cu, C)Ba₂CuO_x films exhibit T_c > 20 K on the cased of conductivity at 290 K (σ_[290 K]) > 4 × 10² S/cm and temperature coefficient of resistivity (TCR) > 1.5 × 10^?3 K^?1, and doping level of them should be in between under-doped and optimally-doped states. Their results suggest that there would be possible to further increases of T_c, and XPS data suggest that (Cu, C)-system should have the excellent dopability in their charge reservoir and the possibility of low anisotropy.     

Mg0.9Zr0.1B2/Cu wires were successfully synthesized by SHS method in the air

Mg_0.9Zr_0.1B₂/Cu wires were successfully synthesized by powder-in-tube (PIT) techniques with self-propagating high-temperature synthesis (SHS) method. We loaded the mixed of Mg, Zr and B power into Cu tube. The tube was drawn to a wire and each end of the tube was sealed by the sealant, then rolled into solenoid with 1.5 cm diameter. The wire was heated up to 270 °C in a furnace with general air pressure, then, ignited the wire with electric arc from one of the end, the self-propagating reaction was completed in 2.0–2.5 s. Finally, the prepared wire was followed by furnace cooling to room temperature. The sample was examined using XRD, SEM, and magnetization measurements. The experiments show that there are small MgCu₂ and boron-rich phases inner sheath wall of copper tube. The magnesium oxide is small in the sample. So, PIT technologies with SHS method is effective in stopping the volatile and oxidize of magnesium. The J_c results show that Mg_0.9Zr_0.1B₂/Cu wires samples which were synthesized by SHS method are better than those sintered for 1 h and Cu clad pure MgB₂ wire. The highest J_c of the prepared Mg_0.9Zr_0.1B₂/Cu wire by SHS method in the air is 5.1 × 10⁵ A/cm² (5 K, 0.5 T), 1.4 × 10⁵ A/cm² (20 K, 1 T) and 4.3 × 10⁴ A/cm² (30 K, 0.5 T).     

Magnetic properties of RPdIn (R=Gd–Er) compounds

AC susceptibility and DC magnetization measurements were performed for the RPdIn (R=Gd–Er) compounds both in the paramagnetic and in the ordered state. In opposite to GdPdIn, which is a ferromagnet (T_c=102 K), the other samples show a complex ferrimagnetic behavior with the additional transition at T_t<T_c. In the high-temperature phase (for T_t<T<T_c), a ferromagnetic interaction dominates, while in the low-temperature phase (for T⩽T_t) antiferromagnetic interactions with the magnetocrystalline anisotropy, especially strong for TbPdIn, come into play. The ordering temperatures are T_c=70, 34, 25 and 12.3 K for Tb-, Dy-, Ho- and ErPdIn respectively, while transition temperatures are T_t=6, 14 and 6 K for Tb-, Dy- and HoPdIn respectively. TbPdIn reveals an additional transition at 27 K connected with the intermediate ferrimagnetic phase. The critical fields for the magnetization process of the low-temperature phase are high (52 and 150 kOe for TbPdIn and 32 kOe for DyPdIn at T=4.2 K) yet these values decrease remarkably with increasing temperature. Results of the study are compared with magnetic and neutron diffraction data hitherto available. We state that irreversibility of the zero-field cooled–field cooled magnetization is not connected with the spin-glass phase claimed elsewhere.