熔体旋甩工艺对Zn掺杂Ⅰ-型Ba8Ga12Zn2Ge32笼合物微结构及热电性能的影响

采用新颖的熔体旋甩(MS)结合放电等离子烧结(SPS)技术制备了单相Zn掺杂的Ⅰ-型Ba₈Ga₁₂Zn₂Ge₃₂笼合物,研究了熔体旋甩工艺对其微结构以及热电性能的影响. 结果表明,MS得到的薄带自由面主要由300nm—1μm的小立方体单晶组成,薄带经SPS烧结后得到了具有大量层状精细结构的致密块体. 与熔融+SPS工艺制备的试样相比,熔融+MS+SPS制备的Ba₈Ga₁₂Zn 关键词： 熔体旋甩 Ⅰ-型笼合物 热电性能     

熔体旋甩工艺对n型InSb化合物的微结构及热电性能的影响

采用新颖的熔体旋甩结合放电等离子烧结技术制备了单相InSb化合物,研究了熔体旋甩工艺对其微结构以及热电性能的影响. 结果表明,熔体旋甩得到的薄带自由面主要由300 nm—2 μm的小柱状晶组成,薄带接触面为非晶或精细纳米晶,薄带经烧结后得到了具有大量层状精细纳米结构的致密块体,尺寸约为40 nm. 与熔融+放电等离子体烧结制备样品相比,在测试温度范围内（300—700 K）,试样的电导率略有下降,但Seebeck系数显著增加,热导率和晶格热导率显著降低,室温下晶格热导率降低幅度约为106%,700 K下晶格热导率的降低幅度达1664%,熔融+熔体旋甩+放电等离子体烧结制备的InSb化合物试样在700 K时其最大ZT值达到049,与熔融+放电等离子体烧结试样相比提高了29%. 关键词： 熔体旋甩 n型InSb化合物 微结构 热电性能     

熔体旋甩工艺对n型InSb化合物的微结构及热电性能的影响

采用新颖的熔体旋甩结合放电等离子烧结技术制备了单相InSb化合物,研究了熔体旋甩工艺对其微结构以及热电性能的影响. 结果表明,熔体旋甩得到的薄带自由面主要由300 nm—2 μm的小柱状晶组成,薄带接触面为非晶或精细纳米晶,薄带经烧结后得到了具有大量层状精细纳米结构的致密块体,尺寸约为40 nm. 与熔融+放电等离子体烧结制备样品相比,在测试温度范围内（300—700 K）,试样的电导率略有下降,但Seebeck系数显著增加,热导率和晶格热导率显著降低,室温下晶格热导率降低幅度约为106%,700 K下晶格热导率的降低幅度达1664%,熔融+熔体旋甩+放电等离子体烧结制备的InSb化合物试样在700 K时其最大ZT值达到049,与熔融+放电等离子体烧结试样相比提高了29%.     

In0.3Co4Sb12-xSex 方钴矿热电材料的制备和热电性能

用熔融退火结合放电等离子烧结法制备了In_0.3Co₄Sb_12-xSe_x(x=0—0.3)方钴矿热电材料,探讨了In的存在形式,系统研究了Se掺杂量对结构和热电性能的影响.结果表明:In可以填充到方钴矿二十面体空洞处,过量In在晶界处形成InSb第二相,Se对Sb的置换使晶格常数减小,In填充上限降低;In_0.3Co₄Sb_12-xSe_x样品呈n型传导,随着Se掺杂量的增大,载流子浓度降低,电导率下降,Seebeck系数增大,功率因子有所降低;由于在结构中引入了质量波动及晶格畸变,适量的Se掺杂可以大幅降低材料晶格热导率;样品In_0.3Co₄Sb₁₂和In_0.3Co₄Sb_11.95Se_0.05的最大ZT值均达到1.0以上. 关键词： 掺杂 填充式方钴矿 热电性能     

熔体旋甩法合成n型(Bi_(0.85)Sb_(0.15))_2(Te_(1-x)Se_x)_3化合物的微结构及热电性能

采用熔体旋甩结合放电等离子烧结(MS-SPS)技术制备了单相n型四元(Bi0.85Sb0.15)2(Te1-xSex)3(x=0.15,0.17,0.19,0.21)化合物,并对所得样品的微结构和热电传输性能进行了系统研究.样品自由断裂面的场发射扫描电子显微镜及抛光面的背散射电子成分分析表明:块体材料晶粒细小,晶粒排列紧密,成分分布均匀且相结构单一,样品中存在大量10—100nm的层状结构.随着Se含量x的增加,样品的电导率和热导率逐渐增加,而Seebeck系数逐渐降低.相比商业应用的区熔材料,MS-SPS方法合成的高Se组成的样品均在425K后表现出更高的ZT值,其中(Bi0.85Sb0.15)2(Te0.83Se0.17)3样品具有最高的ZT值,在360K可达到0.96,并在320—500K均保持较高的ZT值,500K时其ZT值相比区熔材料提高了48%.此外,通过调节Se的含量,可以有效地调控材料的ZT峰值出现的温度段,这对多级或梯度热电器件的制备具有重要意义.     

熔体旋甩工艺对Zn掺杂Ⅰ-型Ba8Ga12Zn2Ge32笼合物微结构及热电性能的影响

采用新颖的熔体旋甩(MS)结合放电等离子烧结(SPS)技术制备了单相Zn掺杂的I-型Ba8Ga12Zn2Ge32笼合物,研究了熔体旋甩工艺对其微结构以及热电性能的影响.结果表明,MS得到的薄带自由面主要由300 nm-1 μm的小立方体单晶组成,薄带经SPS烧结后得到了具有大量层状精细结构的致密块体.与熔融+SPS工艺制备的试样相比,熔融+MS+SPS制备的Ba8Ga12Zn2Ge3笼合物室温载流子浓度增加而迁移率降低,在测试温度范围内,试样的电导率略有下降,Seebeck系数增加,热导率和晶格热导率显著降低,900 K时其晶格热导率从1.06 W/mK降低至0.42W/mK.熔融+MS+SPS制备的Ba8Ca12Zn2Ge32笼合物试样在900 K时其最大ZT值达到0.90,与熔融+SPS试样相比提高了75%.     

p型BayFexCo4-xSb12化合物的热电性能

以2+价的Ba作为填充原子,在x=1.0—1.6,y=0—0.63的组成范围内,系统地研究了Ba填充分数及Fe含量对p型Ba_yFe_xCo_4-xSb₁₂化合物电性能及热性能的影响,探讨了填充原子的氧化价对电性能的影响规律,优化了p型Ba_yFe_xCo_4-xSb₁₂化合物的组成和热电性能,对于富Co组成的Ba_0.27FeCo₃Sb₁₂试样,本研究得到了0.9最大无量纲热电性能指数(ZT). 关键词： 填充分数 载流子浓度 电导率 赛贝克系数 晶格热导率     

Zn掺杂p型Ba8Ga16ZnxGe30－x笼合物的合成及热电性能

用熔融法结合放电等离子烧结方法合成了Zn掺杂单相p型Ge基Ⅰ型笼合物Ba₈Ga₁₆Zn_xGe_30-x(x=3, 4, 5, 6)，探索Zn取代Ge对其热电性能的影响规律，结果表明：所制备的Ba₈Ga₁₆Zn_xGe_30-x化合物为p型传导，随Zn取代量x关键词： p型笼合物 合成 热电性能     

p型Ag0.5(Pb8－xSnx)In0.5Te10化合物的制备及其热电性能

采用高温熔融缓冷和放电等离子烧结工艺制备了p型Ag_0.5(Pb_8-xSn_x)In_0.5Te₁₀五元化合物.研究了Sn含量对化合物载流子传输特性及热电性能的影响规律.结果表明：在Ag_0.5(Pb_8-xSn_x)In_0.5Te₁₀(x 关键词： 0.5(Pb_8-xSn_x)In_0.5Te₁₀')" href="#">Ag_0.5(Pb_8-xSn_x)In_0.5Te₁₀ 合成 载流子 热电性能     

Ca和Ce双原子复合填充p型CamCenFexCo4－xSb12化合物的合成及热电性能

用高温熔融法合成了Ca和Ce复合填充的单相p型Ca_mCe_nFe_{xCo4-xSb12化合物，探索了两种原子复合填充对其热电性能的影 响规律.研究结果表明，填充分数相同时，Ca和Ce两种原子复合填充的p型CamCe nFexCo4-xSb12化合物的载流子浓度和电 导率介于Ca或Ce一种原子单独填充的化合物之间，且随两种原子填充分数m+n的增加而降低 ；赛贝克系数随两种原子填充总量，尤其是Ce填充分数m的增加以及温度的上升而增加；在 相同填充分数时，两种原子复合填充的p型CamCenFexC o4-xSb12化合物的晶格热导率较Ca或Ce一种原子单独填充的化合物 的晶格热导率低，当总填充分数m+n为0.3左右，且Ca和Ce的填充量大致相等时，化合物的晶 格热导率最低.p型Ca0.18Ce0.12Fe1.45Co2.55Sb12.21化合物的最大热电性能指数ZT值在750K时达到1.17. 关键词： skutterudite化合物 双原子复合填充 合成 热电性能}     

Crystallization of Fe-B amorphous alloy powders produced by chemical reduction

The crystallization behaviour of the Fe?B amorphous alloy powders prepared by the chemical reduction method has been investigated by Mössbauer spectroscopy. In comparison to amorphous ribbons prepared by melt-spinning, a different crystallization behaviour has been observed. After annealing the amorphous samples entirely crystallized into three crystalline phases: α-Fe, Fe₃B, and Fe₂B. In the case of Fe₈₀B₂₀ amorphous alloy ribbons produced by melt-spinning technique eutectic crystallization is commonly observed and results in the crystalline phases: α-Fe and Fe₃B. This kind of crystallization was not observed in the chemically prepared samples. The metastable tetragonal Fe₃B phase transformed completely into α-Fe and Fe₂B after annealing at 973 K for one hour.     

纳米复合永磁Pr9Fe74Co12B5Snx(x=0, 0.5)的磁化行为与磁黏滞性

用熔体快淬法制备了纳米复合永磁样品Pr₉Fe₇₄Co₁₂B₅ 与Pr₉Fe₇₄Co₁₂B₅Sn_0.5，分析了样品的起始磁化、反磁化过程，测得样品的总磁化率、可逆磁化率以及样品的磁黏滞性.结果表明，两样品在室温下均表现为单一硬磁相磁化行为，在低温下表现为双相行为，且由于添加Sn后使晶粒均匀化从而导致样品低温下的双相行为更加明显.添加Sn后引起样品中软磁相含量和软磁相晶粒尺寸的增加，使磁化反转中可逆磁化部分增多，且使反磁化形核场降低.磁黏滞性研究表明，热激活体积与软磁相晶粒的大小有关. 关键词： 纳米复合永磁 磁化反转 磁粘滞     

Melt-spun magnetically anisotropic SmCo5 ribbons with high permanent performance

We have succeeded in preparing magnetically anisotropic SmCo₅ ribbons with high permanent performance by single-roller melt spinning at low wheel velocity. The anisotropy is associated with a crystallographic texture formed during melt-spinning process, with the c-axis parallel to the longitudinal direction of the ribbons. The formation of the crystallographic texture is attributed to a directional solidification process resulting from a thermal gradient. A remanence of 9.1 kG, remanence ratio of 0.9, intrinsic coercivity of 16.2 kOe and energy product of 18.2 MGOe at room temperature are obtained in the melt-spun and subsequently annealed SmCo₅ ribbons prepared at 5 m/s.     

急冷条件下NiAl-Mo三元共晶合金的组织形成机制

采用单辊急冷技术实现了NiAl-Mo三元两相共晶合金的快速凝固, 同时与常规条件下的凝固组织进行了对比研究. 实验发现, 单辊急冷的合金条带与常规条件的凝固样品均由B2结构的NiAl金属间化合物和bcc结构的Mo固溶体两相组成, 两相均具有(110)晶面优先生长的趋势, 并呈现出(110)NiAl//(110)Mo取向关系. 常规条件下得到的微观结构主要由规则的两相共晶组织组成, 形成了类似菊花状的共晶胞. 而单辊急冷条件下形成的组织结构主要是由近辊面的柱状晶区和近自由面的等轴晶区组成的凝固组织. 理论计算发现, 合金熔体的单辊辊速由10 m/s增大至50 m/s后, 其冷却速率从1.01×10⁷ K/s逐渐增大到2.46×10⁷ K/s, 冷却速率明显高于常规铸造过程, 因而形成了差别很大的凝固组织. 随着辊速(冷却速率)的增加, 合金条带的厚度从54.4 μm减小至22 μm, 近辊面柱状晶区的厚度所占比例也逐渐增大, 晶粒发生了明显细化. 关键词： 快速凝固 三元共晶 共晶转变 冷却速率     

不同快淬速度对Nd8Fe85Mo1B6磁性的影响

通过直接快淬制备了不同淬速的Nd₈Fe₈₅Mo₁B₆样品.由振动样品磁强计测量的结果发现,快淬速度对样品的磁性有很大的影响.对样品进行X射线衍射和热磁分析发现,随着淬速的增加样品中的TbCu₇相增多,同时软磁相的晶粒尺寸降低,认为样品的相组成和晶粒尺寸的变化是其磁性存在差异的原因. 关键词：     

Quick preparation and thermal transport properties of nanostructured β-FeSi2 bulk material

This paper reports that the nanostructured β-FeSi2 bulk materials are prepared by a new synthesis process by combining melt spinning(MS) and subsequent spark plasma sintering(SPS).It investigates the influence of linear speed of the rolling copper wheel,injection pressure and SPS regime on microstructure and phase composition of the rapidly solidified ribbons after MS and bulk production respectively,and discusses the effects of the microstructure on thermal transport properties.There are two crystalline phases(α-Fe2Si5 and ε-FeSi) in the rapidly solidified ribbons;the crystal grains become smaller when the cooling rate increases(the 20 nm minimum crystal of ε-FeSi is obtained).Having been sintered for 1 min above 1123 K and annealed for 5 min at 923 K,the single-phase nanostructured βFeSi2 bulk materials with 200-500 nm grain size and 98% relative density are obtained.The microstructure of β-FeSi2 has great effect on thermal transport properties.With decreasing sintering temperature,the grain size decreases,the thermal conductivity of β-FeSi2 is reduced remarkably.The thermal conductivity of β-FeSi2 decreases notably(reduced 72% at room temperature) in comparison with the β-FeSi2 prepared by traditional casting method.     

Facile synthesis of nanostructured n-type SiGe alloys with enhanced thermoelectric performance using rapid solidification employing melt spinning followed by spark plasma sintering

SiGe alloy is widely used thermoelectric materials for high temperature thermoelectric generator applications. However, its high thermoelectric performance has been thus far realized only in alloys synthesized employing mechanical alloying techniques, which are time-consuming and employ several materials processing steps. In the current study, for the first time, we report an enhanced thermoelectric figure-of-merit (ZT) ∼ 1.1 at 900 °C in n-type Si₈₀Ge₂₀ nano-alloys, synthesized using a facile and up-scalable methodology consisting of rapid solidification at high optimized cooling rate ∼ 3.4 × 10⁷ K/s, employing melt spinning followed by spark plasma sintering of the resulting nano-crystalline melt-spun ribbons. This enhancement in ZT > 20% over its bulk counterpart, owes its origin to the nano-crystalline microstructure formed at high cooling rates, which results in crystallite size ∼7 nm leading to high density of grain boundaries, which scatter heat-carrying phonons. This abundant scattering resulted in a very low thermal conductivity ∼2.1 Wm⁻¹K⁻¹, which corresponds to ∼50% reduction over its bulk counterpart and is amongst the lowest reported thus far in n-type SiGe alloys. The synthesized samples were characterized using X-ray diffraction, scanning electron microscopy and transmission electron microscopy, based on which the enhancement in their thermoelectric performance has been discussed.     

Exchange bias behavior in Ni50.0Mn35.5 In14.5 ribbons annealed at different temperatures

Heusler alloy Ni_50.0Mn_35.5In_14.5 ribbons were prepared by melt-spinning technique. Several short time annealings were carried out in order to enhance the exchange bias effect in this alloy ribbon. The magnetic transition temperature increases with the annealing, compared to the as-spun sample, however no significant differences in respective Curie temperatures were observed for austenite and martensite phases in such annealed samples. Exchange bias effect is observed at low temperatures for all samples and practically vanishes at 60 K for the as-spun sample, whereas for the annealed ribbons it vanishes at 100 K.     

Amorphous-crystalline dual-layer structures resulting from metastable liquid phase separation in （Fe50Co25B15Si10）80Cu20 melt-spun ribbons

（Fe50Co25B15Si10）80Cu20 ribbons are prepared by using the single-roller melt-spinning method. A dual-layer structure consisting of a （Fe, Co）-rich amorphous phase and a Cu-rich crystalline phase forms due to metastable liquid phase separation before solidification. The magnetic hysteresis loops of the as-quenched and annealed samples are measured at room temperature. It is indicated that the coercivity of the ribbon is almost zero in the as-quenched state. The crystallization leads to the increase of coercivity and decrease of saturation magnetization.