Chitosan-ZnO/polyaniline ternary nanocomposite for high-performance supercapacitor

We report on the synthesis of chitosan-zinc oxide (ZnO)/polyaniline (CS-ZnO/PANI) ternary nanocomposites via in situ polymerization of aniline in the presence of CS-ZnO nanocomposite prepared by simple precipitation method. The structure, morphology, and physicochemical properties of prepared ternary composites are characterized by Fourier transform infrared, UV–visible, X-ray diffraction, SEM, EDXS, TEM, thermogravimetric/differential thermal analysis, and N₂ adsorption/desorption measurements. Their electrochemical properties are also investigated using cyclic voltammetry, galvanostatic charge–discharge tests, and electrochemical impedance spectroscopy. Electrochemical measurements show that the mesoporous CS_0.12-ZnO_2.5/PANI electrode yields larger specific capacitance (587.15 F g^?1) than the corresponding PANI-ZnO electrode without added chitosan and the capacitance retention is 80 % after 1,000 charge/discharge cycles at 175 mA cm^?2 current density in the voltage range of 0 to 0.8 V vs. SCE, due to the synergistic effect among three components which result in enhanced specific capacitance and cycling stability. The resulting composites are promising electrode materials for high-performance, environmentally friendly, and low-cost electrical energy storage devices.     

Synthesis and microwave absorption properties of graphene-oxide(GO)/polyaniline nanocomposite with Fe3O4 particles

In order to investigate the impedance matching properties of microwave absorbers,the ternary nanocomposites of GO/PANI/Fe₃O₄（GPF） are prepared via a two-step method,GO/PANI composites are synthesized by dilute polymerization in the presence of aniline monomer and GO,and GO/PANI/Fe₃O₄ is prepared via a co-precipitation method.The obtained nanocomposites are characterized by scanning electron microscopy（SEM）,X-ray diffraction（XRD）,and Fourier transform infrared spectroscopy（FTIR）,respectively.The microwave absorbability reveals enhanced microwave absorption properties compared with GO,PANI,and GO/PANI.The maximum reflection loss of GO/PANI/Fe₃O₄ is up to-27 dB at 14 GHz with its thickness being 2 mm,and its absorption bandwidths exceeding-10 dB are more than 11.2 GHz with its thickness values being in the range from 1.5 mm-4 mm.It provides that GO/PANI/Fe₃O₄ can be used as an attractive candidate for microwave absorbers.     

苯胺和丙烯酸协同聚合一步法制备聚苯胺纳米管

本文通过加入过硫酸铵(APS)引发苯胺和丙烯酸(AA)在水溶液中的协同聚合反应,一步合成出具有中空结构的聚苯胺纳米管. 聚苯胺纳米管的外径平均为180 nm,内径约80 nm,其形成取决于苯胺与丙烯酸的摩尔比(X_{ani/AA}). 当X_{ani/AA}不超过1时,主要得到聚苯胺纳米管. 在三电极体系中测定了所制备的聚苯胺纳米管的电化学性能. 在1 mol/L H₂SO₄为电解液,电流密度为0.5 A/g的条件下,聚苯胺纳米管比电容高达436 F/g,是通常聚苯胺纳米片的七倍. 此外,在0.5 A/g的电流密度下进行500次充放电循环后,其比电容能够保持最初始的89.2%,表现出优异的充放电循环稳定性.     

rGO supported self-assembly of 2D nano sheet of (g-C3N4) into rod-like nano structure and its application in sonophotocatalytic degradation of an antibiotic

Graphitic carbon nitride (g-C₃N₄) is an analog of graphite due to its unique electronic structure. g-C₃N₄ based materials have been used in photocatalytic applications. However, pure g-C₃N₄ suffers from major shortcomings which include poor disparity, low surface area and a high recombination rate of photo generated electron-hole pairs that significantly reduce its photocatalytic activity. In this work, self-assembly of g-C₃N₄ sheet into rod shaped g-C₃N₄ was developed via a simple polymerisation method. A composite made of g-C₃N₄ nanorods and rGO (rGO-RCN) was also prepared. The band gap g-C₃N₄ was shifted from 2.77 to 2.6 eV evidented by UV-DRS data. As a result, rGO-RCN showed a relatively high absorption in the visible region. Moreover, a fast electron transfer rate was observed with rGO-RCN composite as conformed from PL analysis and photocurrent measurement. The formation of nanorod and sheet morphologies was confirmed via TEM analysis. The photocatalytic activities of prepared sheet-g-C₃N₄ (SCN)_, Rod g-C₃N₄ (RCN), reduced graphene oxide supported sheet-g-C₃N₄ (rGO-SCN) and reduced graphene oxide supported Rod-g-C₃N₄ (rGO-RCN) were evaluated using a commonly used antibiotic (tetracycline). Among these catalysts, rGO-RCN nanocomposite showed sonophotocatalytic activity 3 times higher compared to pure g-C₃N₄. This superior sonophotocatalytic activity could be due to enhanced visible light absorption of the material, active sites generated by ultrasound, and the high electron transport property of rGO.     

Synthesis and Characterization of La‐Doped Fe3O4‐Polyaniline Magnetic Response Nanocomposites

Lanathum (La)‐doped Fe₃O₄ magnetic nanoparticles were prepared in aqueous solution at room temperature, then La‐doped Fe₃O₄‐polyaniline (PANI) nanocomposites containing a dispersion of La‐doped Fe₃O₄ nanoparticles were synthesized via in‐situ polymerization of aniline monomer. The structure and properties of the synthesized samples were characterized with X‐ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectrometry (FTIR), thermogravimetric analysis (TGA), inductively coupled plasma atomic emission spectrometry (ICPAES), and a vibrating sample magnetometer (VSM). The resulting particles of La‐doped Fe₃O₄ and La‐doped Fe₃O₄‐PANI were almost spherical with diameters ranging from 15 to 25 nm and 25 to 85 nm, respectively. The La‐doped Fe₃O₄‐PANI composite presented core‐shell structures; polyaniline covered the La‐doped Fe₃O₄ completely. The specific saturation magnetization of La‐doped Fe₃O₄‐PANI depended on the starting material of La‐doped Fe₃O_4. It increased with increasing amounts of La and Fe₃O₄ content.     

Electrochemical synthesis and performance of PANI electrode material for electrochemical capacitor

Polyaniline (PANI) electrode materials doped with sulfuric acid (H₂SO₄) were prepared by cyclic voltammetry (CV) method in different reaction conditions. The structure and morphology of PANI samples were characterized by Fourier transform infrared spectroscopy and scanning electron microscope. The electrochemical properties of PANI samples were studied by CV, galvanostatic charge/discharge, and electrochemical impedance spectroscopy tests. Additionally, the effects of reaction conditions including aniline concentration, voltammetry scan rate, and deposition time on the morphology and properties of PANI samples were investigated in detail. The results showed that the PANI synthesized under the optimal conditions of 0.2 mol?L^?1 aniline, scan rate 20 mV?s^?1, and deposition time 50 min is in the form of nanorods with a cross-linked network structure. It exhibits an outstanding capacitive performance with good cycle stability and high rate performance. Besides, the specific capacitance of PANI is as high as 757 F?g^?1.     

Novel molybdenum disulfide nanosheets–decorated polyaniline: Preparation,characterization and enhanced electrocatalytic activity for hydrogen evolution reaction

Novel molybdenum disulfide nanosheets–decorated polyaniline (MoS₂/PANI) was synthesized and investigated as an efficient catalyst for hydrogen evolution reaction (HER). Compared with MoS₂, MoS₂/PANI nanocomposites exhibited higher catalytic activity and lower Tafel slope for HER in H₂SO₄ solution. The amount of 19 wt% PANI for coupling with MoS₂ resulted in a high current density of 80 mA cm⁻² at 400 mV (vs. RHE). In addition, the optimal MoS₂/PANI nanocomposite showed impressive long-term stability even after 500 cycles. The enhanced catalytic activity of MoS₂/PANI nanocomposites was primarily ascribed to the effective electron transport channels of PANI and the increase of electrochemically accessible surface area in composite materials, which was advantageous to facilitate the charge transfer at catalyst/electrolyte interface.     

Modified g-C3N4/TiO2 nanosheets/ZnO ternary facet coupled heterojunction for photocatalytic degradation of p-toluenesulfonic acid (p-TSA) under visible light

Novel ternary nanocomposites with facet coupled structure were synthesized by using modified g-C₃N₄, TiO₂ nanosheets and nano-ZnO. Nanosheet/nanosheet heterojunction structure was investigated by TEM, XPS and XRD. FT–IR and Nitrogen adsorption were illustrated for chemical/physical structure analyses. Solution of p-Toluenesulfonic acid (p-TSA) was chosen as target pollutant for visible light photodegradation and the excellent removal efficiency was achieved by this structurally modified g-C₃N₄/TiO₂/ZnO hybrid. The visible light absorption improvement and quantum efficiency enhancement, which were testified by UV–vis DRS, PL and p-TSA photodegradation measurements, due to the facet coupled structure and appropriate quantity of modified g-C₃N₄ in the nanocomposites.     

In situ synthesis and characterization of LiNi0.5La0.08Fe1.92O4-polyaniline core-shell nanocomposites

Core-shell-structured LiNi_0.5La_0.08Fe_1.92O₄-polyaniline (PANI) nanocomposites with magnetic behavior were synthesized by in situ polymerization of aniline in the presence of LiNi_0.5La_0.08Fe_1.92O₄ nanoparticles. The structure, morphology and magnetic properties of samples were characterized by powder X-ray diffraction (XRD), Fourier transform infrared (FTIR), UV-vis absorption, transmission electron microscopy (TEM) and vibrating sample magnetometer (VSM) technique. The results of spectroanalysis indicated that there was interaction between PANI chains and ferrite particles. TEM study showed that LiNi_0.5La_0.08Fe_1.92O₄-PANI nanocomposites presented a core-shell structure with a magnetic core of 30-50 nm diameter and an amorphous shell of 10-20 nm thickness. The nanocomposites under applied magnetic field exhibited the hysteresis loops of the ferromagnetic nature. The saturation magnetization and coercivity of nanocomposites decreased with decreasing content of LiNi_0.5La_0.08Fe_1.92O₄. The polymerization mechanism and bonding interaction in the nanocomposites have been discussed.     

Characterization and optimization of Ce0.6Zr0.4−x Mn x O2 (x ≤ 0.4)

In situ synthesis method is used to synthesize g-C₃N₄-P25 composite photocatalysts with different mass rations. The experiment result shows that P25 particles with diameter at range of 20–30 nm were embedded homogenously in the sheets of g-C₃N₄. Coupling g-C₃N₄ with P25 can not only improve the visible light absorption, but also improve the visible light photocatalytic activity of P25. The g-C₃N₄-P25 nanocomposite has the higher photocatalytic activity than g-C₃N₄ under visible light. The optimal g-C₃N₄ content with the highest photocatalytic activity is determined to be 84 %, which is almost 3.3 times higher than that of individual g-C₃N₄ under the visible light. The enhanced visible light photocatalytic activity could be ascribed to the formation of g-C₃N₄ and TiO₂ heteojunction, which results in an efficient separation and transfer of photo-induced charge carriers. The electron spin resonance results show that the ^·O₂ ^? radicals are main active species for g-C₃N₄ and the g-C₃N₄-P25 nanocomposites.     

g-C3N4 modified Bi2O3 composites with enhanced visible-light photocatalytic activity

Novel g-C₃N₄ modified Bi₂O₃ (g-C₃N₄/Bi₂O₃) composites were synthesized by a mixing-calcination method. The samples were characterized by thermogravimetry (TG), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM), UV–vis diffuse reflection spectroscopy (DRS), photoluminescence (PL) and photocurrent-time measurement (PT). The photocatalytic activity of the composites was evaluated by degradation of Rhodamine B (RHB) and 4-chlorophenol (4-CP) under visible light irradiation (>400 nm). The results indicated that the g-C₃N₄/Bi₂O₃ composites showed higher photocatalytic activity than that of Bi₂O₃ and g-C₃N₄. The enhanced photocatalytic activity of the g-C₃N₄/Bi₂O₃ composites could be attributed to the suitable band positions between g-C₃N₄ and Bi₂O₃. This leads to a low recombination between the photogenerated electron–hole pairs. The proposed mechanism for the enhanced visible-light photocatalytic activity of g-C₃N₄/Bi₂O₃ composites was proven by PL and PT analysis.     

Ultrasonic-assisted preparation and characterization of magnetic ZnFe2O4/g-C3N4 nanomaterial and their applications towards electrocatalytic reduction of 4-nitrophenol

Nanoball-structured ferromagnetic zinc ferrite nanocrystals (ZnFe₂O₄ NPs) entrapped with graphitic-carbon nitride (g-C₃N₄) was produced via straightforward and facile sonochemical synthetical technique (titanium probe; 100 W/cm² and 50 KHz). The morphological (SEM), elemental (EDS), diffraction (XRD), XPS, and electrochemical studies (CV) have been carry out to verify the nanostructure and shape of the materials. The ZnFe₂O₄ NPs/g-C₃N₄ electrode (GCE) was constructed which displayed outstanding electrochemical ability towards toxic 4-nitrophenol (NTP). A sensitive, selective, reproducible, and durable electrochemical NTP sensor was developed by ZnFe₂O₄ NPs/g-C₃N₄ modified electrode. The modified sensor exhibited a high sensitivity and 4.17 nanomolars of LOD. It’s greater than the LOD of previously reported NTP modified sensors. The real-time experiments of the modified electrochemical (ZnFe₂O₄ NPs/g-C₃N₄ electrode) sensor were successfully explained in various water (river and drinking) samples and its showed high standard recoveries. Therefore, sonochemical synthetical method and fabrication of modified electrode were developed this work based on environmental analysis of NTP sensor.     

Pickering emulsion polymerization of polyaniline/LiCoO2 nanoparticles used as cathode materials for lithium batteries

The oil in water (o/w) emulsions were prepared using aniline dissolved in toluene and LiCoO₂ particles as stabilizers (Pickering emulsions). Pickering emulsions are stabilized by adsorbed solid particles instead of emulsifier molecules. The mean droplet diameter of emulsions was controlled by the mass ratio M (oil)/M (solid particles). The emulsions showed great stability during 3 days. The composite materials containing LiCoO₂ and the conductive polymer polyaniline (PANI) have been prepared by means of polymerization of aniline emulsion stabilized by LiCoO₂ particles. The composite materials were characterized by nanosphere and nanofiber-like structures. The nanofiber-like morphology of the powdered material was distinctly different of the morphologies of the parent materials. The electrochemical reactivity of PANI/LiCoO₂ composites as positive electrode in a lithium battery was examined during lithium ion deinsertion and insertion by galvanostatic charge–discharge testing; PANI/LiCoO₂ (1:4) composite materials exhibited the best electrochemical performance by increasing the reaction reversibility and capacity compared to that of the pristine LiCoO₂ cathode. The first discharge capacity of PANI/LiCoO₂ (1:4) was 167 mAh/g, while that of LiCoO₂ was136 mAh/g.     

Fabrication of g-C3N4/NiO heterostructured nanocomposite modified glassy carbon electrode for quercetin biosensor

Herein, we report a one-pot synthesis of structurally uniform and electrochemically active graphitic carbon nitride/nickel oxide (g-C₃N₄/NiO) nanocomposite and an investigation on the electrocatalytic oxidation of quercetin (QR). The synthesized g-C₃N₄/NiO nanocomposite has uniform surface distribution, which was characterized with scanning electron microscopy (SEM). Moreover, the composition of synthesized g-C₃N₄/NiO nanocomposite was characterized by UV–vis-spectroscopy, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR spectra), BET, SEM and HRTEM. The g-C₃N₄/NiO was electrochemically treated in 0.1 MPBS solution through cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The peak current response increases linearly with QR concentration from 0.010 μM to 250 µM with a fast response time of less than 2 s and a detection limit of 0.002 μM. To further evaluate the feasibility of using this sensor for real sample analysis, QR content in various real samples including green tea, green apple, honey suckle were determined and satisfactory results were achieved.     

Preparation and characterization of graphitic carbon nitride through pyrolysis of melamine

Graphitic carbon nitride (g-C₃N₄) has been synthesized via a two-step pyrolysis of melamine (C₃H₆N₆) at 800°C for 2 h under vacuum conditions. X-ray diffraction (XRD) patterns strongly indicate that the synthesized sample is g-C₃N₄. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) morphologies indicate that the product is mainly composed of graphitic carbon nitride. The stoichiometric ratio of C:N is determined to be 0.72 by elemental analysis (EA). Chemical bonding of the sample has been investigated by X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). Electron energy loss spectroscopy (EELS) verifies the bonding state between carbon and nitrogen atoms. Optical properties of the g-C₃N₄ were investigated by PL (photoluminescence) measurements and UV–Vis (ultraviolet–visible) absorption spectra. We suppose its luminescent properties may have potential application as component of optical nanoscale devices. Thermogravimetric analysis (TGA) and differential thermal analysis (DTA) were also performed.     

Sonocatalytic degradation of tetracycline hydrochloride with CoFe2O4/g-C3N4 composite

In this work, different mass percent ratios of CoFe₂O₄ coupled g-C₃N₄ (w%-CoFe₂O₄/g-C₃N₄, CFO/CN) nanocomposites were integrated through a hydrothermal process for the sonocatalytic eradication of tetracycline hydrochloride (TCH) from aqueous media. The prepared sonocatalysts were subjected to various techniques to investigate their morphology, crystallinity, ultrasound wave capturing activity and charge conductivity. From the investigated activity of the composite materials, it has been registered that the best sonocatalytic degradation efficiency of 26.71 % in 10 min was delivered when the amount of CoFe₂O₄ was 25% in the nanocomposite. The delivered efficiency was higher than that of bare CoFe₂O₄ and g-C₃N₄. This enriched sonocatalytic efficiency was credited to the accelerated charge transfer and separation of e⁻-h⁺ pair through the S-scheme heterojunctional interface. The trapping experiments confirmed that all the three species i.e. ^•OH, h⁺ and ^•O₂⁻ were involved in the eradication of antibiotics. A strong interaction was shown up between CoFe₂O₄ and g-C₃N₄ in the FTIR study to support charge transfer as confirmed from the photoluminescence and photocurrent analysis of the samples. This work will provide an easy approach for fabricating highly efficient low-cost magnetic sonocatalysts for the eradication of hazardous materials present in our environment.     

Synergistic effect of efficient adsorption g-C3N4/ZnO composite for photocatalytic property

Novel g-C₃N₄/ZnO composite photocatalyst was synthesized from an oxygen-containing precursor by direct thermal decomposition urea in air without any other templates assistance. Different percentages of g-C₃N₄ were hybridized with ZnO via the monolayer-dispersed method. The prepared g-C₃N₄/ZnO composites were characterized by XRD, SEM, UV–vis diffuse reflectance spectra (DRS), FT-IR, TEM and XPS. The composites showed much higher efficiency for degradation of Rhodamine B (RhB) than ZnO under UV and visible light irradiation. Especially, the photocatalytic efficiency was the highest under UV light irradiation when the percentage of g-C₃N₄ was 6%. The improved photocatalytic activity may be due to synergistic effect of photon acquisition and direct contact between organic dyestuff and photocatalyst. Then, effective separation of photogenerated electron–hole pairs at the interface of g-C₃N₄ is an important factor for improvement of photocatalytic activity. This work indicates that g-C₃N₄ hybrid semiconductors photocatalyst is a promising material in pollutants degradation.     

Synthesis and photocatalytic activity of polyaniline–TiO<Subscript>2</Subscript> composites with bionic nanopapilla structure

Polyaniline (PANI)–TiO₂ nanocomposites possessing both nano and microscale structures were prepared through a facile hydrothermal route in the presence of PANI. The nanopapilla particles were characterized by scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray analysis, X-ray photoelectron spectra, X-ray diffraction, FTIR spectra, UV–Vis spectroscopy, and N₂ adsorption analysis, etc. The results show that the composites possess both nano and microscale structures. The TiO₂ nanorods are dispersed on PANI with one end fixed to the surface. The photocatalytic properties of the powders were verified by the photodegradation of gaseous acetone under UV (λ = 254 nm) and visible-light irradiation (λ > 400 nm). In fact, the photocatalytic effects exhibited by the composite particles were superior to that of pure TiO₂ and P25 samples. This excellent behavior is attributed to the structural features of PANI–TiO₂ microspheres and the synergistic effect between PANI and TiO₂ which facilitates a larger amount of surface active sites. This in turn causes a faster charge separation and slower charge recombination which results in a more efficient decomposition of gaseous pollutants.     

高比表面积TiO2与g-C3N4复合材料的光催化性能及机理研究

本文通过简单的溶剂热法制备了g-C₃N₄与高比表面积的TiO₂复合材料,该方法操作简单且能耗低. 甲基橙降解实验结果表明,高比表面积的TiO₂有效提高了光催化活性. 光电化学测试结果表明,与g-C₃N₄复合后,TiO₂的电荷载流子迁移速率得到明显改善. g-C₃N₄/高比表面积-TiO₂的光催化活性很强,在100分钟内,6%-g-C₃N₄/高比表面积-TiO₂对甲基橙的降解程度可达92.44%. 6%-g-C₃N₄/高比表面积-TiO₂不仅具有良好的光催化降解性能,还具有较高的稳定性. 本文对6%-g-C₃N₄/高比表面积-TiO₂的光催化机理也进行了系统的研究.     

Polyaniline/LiNi0.5La0.08Fe1.92O4 Nanocomposite: A Study of Dielectric and Electric Modulus Spectroscopy

Polyaniline(PANI)/LiNi_0.5La_0.08Fe_1.92O₄ nanocomposite was synthesized by an in situ polymerization of aniline in the presence of LiNi_0.5La_0.08Fe_1.92O₄ nanoparticles. The dielectric properties of a PANI/LiNi_0.5La_0.08Fe_1.92O₄ (10 wt% weight ratio of LiNi_0.5La_0.08Fe_1.92O₄ to aniline monomer) nanocomposite were investigated in the frequency range of 10⁶–10⁹ Hz. The dielectric constant (?′) and dielectric loss (?″) were frequency dependent, having relatively high values at low frequency and decreasing with increasing frequency. The values of ?′ and ?″ of PANI/LiNi_0.5La_0.08Fe_1.92O₄ nanocomposite were found to be lower than those of the pristine PANI. Electric modulus analysis was carried out to understand the electrical relaxation process.