介质柱型二维Triangular格子光子晶体的禁带特性

采用平面波展开法数值计算了空气背景中由圆形、正六边形和正方形介质柱构造的二维三角晶格光子晶体禁带结构,并研究了介质方柱旋转角度、介质折射率和填充比对完全光子禁带宽度的影响.结果表明,在低频区,介质方柱旋转17°时,出现最大完全光子禁带,且最大禁带宽度随介质折射率的变化较为稳定.在高频区,介质方柱旋转30°时,完全光子禁带宽度最大;且介质材料折射率n=2.2时即出现完全光子禁带,n=2.6时,完全光子禁带达到最大.     

大带隙二维三角格子光子晶体结构参数的优化设计

光子晶体结构设计优化是理论研究的一个重要内容.运用平面波展开法对圆柱、方柱及正六边柱构造的二维三角格子光子晶体的禁带进行仿真计算,讨论了介质材料分别为GaAs、Si和Ge情况下,柱子形状、旋转角度、填充比的变化对完全光子禁带的影响.发现:对于二维三角格子光子晶体,相对于介质柱,空气柱更易获得完全光子禁带;而相对于圆柱及...     

TM模式下二维非磁化等离子体光子晶体的禁带调制特性分析

采用时域有限差分法(FDTD)中的分段线性电流密度卷积(PLCDRC)算法研究了TM波入射时二维非磁化等离子体光子晶体的禁带特性.从频域角度分析得到微分高斯脉冲的透射系数,并讨论该光子晶体的介质圆柱的介电常数、晶格常数、介质圆柱半径,周期常数和等离子体参数对其禁带特性的影响.结果表明,增加周期常数和等离子体碰撞频率不会改变禁带宽度,增加介质圆柱的相对介电常数和等离子体频率可以展宽禁带的宽度. 当填充率一定时,减小介质圆柱的半径和晶格常数可以实现禁带的拓展. 关键词： 等离子体 光子晶体 禁带 PLCDRC算法     

二维正方光子晶体完全禁带与导波特性数值分析

以简单二维正方排列的光子品体为例,计算分析了完全禁带随介质填充率和介质折射率比变化出现的条件和规律,结果显示对两者同时进行调谐是获取完全禁带的最佳途径,选取晶格常数为0.7 μm,介质填充率0.5,介质折射率比为4时,在光子晶体中引人线缺陷后,对处于完全禁带中的波长为1.55μm的光显示良好的导波特性.     

禁带理论应用于溶液浓度检测的研究

利用平面波展开法针对三角晶格二维光子晶体的禁带结构进行了数值模拟,研究了不同浓度的NaCl溶液和酒精溶液对光子带隙的影响。选用砷化镓为三角晶格光子晶体的背景材料,这两种溶液分别为三角晶格二维光子晶体的空气孔介质材料。当不同浓度和不同折射率的NaCl溶液和酒精溶液注入光子晶体中,TE模式不出现带隙,而TM模式出现宽度不同的五种带隙,为方便选取了最大禁带宽度为参考数据。     

二维斜三角晶格光子晶体完全带隙研究

在二维正三角晶格光子晶体的基础上,通过改变晶体的晶格基矢构造了一种全新的周期结构。该周期结构的最小周期单元不再是传统意义上的等边三角形,而是一种更为优化的斜三角形结构。利用平面波展开法理论模拟了二维斜三角晶格光子晶体完全带隙的情况,发现所设计结构的完全带隙宽度是二维正三角晶格光子晶体完全带隙宽度的4.3 2倍。分析了介质柱宽度,介质柱旋转角度以及相对介电常数对所构造结构的完全带隙的影响,所得结果对二维光子晶体的理论研究和实际应用有所帮助。为任意角度的二维光子晶体集成波导的研究和制作提供了理论基础。     

二维圆柱形光子晶体的完全禁带研究

用平面波展开法研究了二维圆柱形光子晶体的完全禁带与填充比、介电常数比之间的关系. 研究发现,并非介电常数比越大,完全禁带宽度就越大,而是有一个峰值. 关键词： 二维光子晶体 完全禁带 平面波展开法     

二维光子晶体能带结构温度特性研究

采用有限元法对二维光子晶体的能带特性进行了分析.当光子晶体所受的温度发生变化时,由于构成二维光子晶体介质的热光效应,引起介质的折射率变化,介质的热膨胀效应引起介质厚度发生变化,改变了光子晶体的晶格周期,使得光子晶体的能带结构发生变化.分析了温度变化对二维光子晶体的第一禁带和第二禁带结构特性的影响,各禁带的起始波长、截止...     

圆环杆与平板连杆的适合光路集成的二维正方晶格光子晶体

提出了一种基于圆环杆与平板连杆的二维正方晶格光子晶体结构,讨论了绝对禁带的计算过程和各参数对绝对禁带宽度的影响.通过平面波展开法结合逐次逼近方法发现其最大绝对禁带相对值达到19.026％,比采用圆柱杆和平板连杆结构的二维正方晶格光子晶体以及采用圆环杆但无连杆的二维正方晶格光子晶体的最大绝对禁带相对值分别提高10.181％和712.035 9％;圆环杆的外径、圆环的相对厚度以及连杆的宽度都存在一个最佳值,且连杆宽度对绝对禁带相对值的影响比较敏感.     

二维光子晶体层状超晶格透射特性研究

把平面波展开法(Plane Wave Expansion Method,PWM)用于数值研究圆柱柱体粗细及折射率层状间隔构成的二维光子晶体超晶格的传输特性.数值结果表明,层状超晶格的透射谱中禁带宽度在柱体折射率相同时与粗细柱体半径差异成线性关系,半径相差越大禁带宽度越小,禁带中心位置越向低频方向移动.在半径相同时禁带宽度与层间折射率差异同样成线性关系,折射率相差越大禁带宽度越小,禁带中心位置越向低频方向移动.因此人们可以根据实际应用中的禁带需要利用上述各种可调因素进行调节.     

Superprism properties in 2D polymer photonic crystals at high normal frequencies

The superprism effects of higher bands, i.e., for normal frequencies of higher than one, in two-dimensional (2D) polymer photonic crystals (PCs) are investigated. It is shown that in a polymer PC of triangular symmetry with filling factor of about 31%, the gradual transition of the hexagonal into triangular equi-frequency dispersion contours leads to a strong superprism in the 6th band at a normal frequency of 1.2. This dispersion is more prominent than those observed in the lower bands in 2D PCs. Also, this requires a lattice constant longer than the concerned wavelength. Furthermore, in a 2D polymer PC with a filling factor of about 83% a strong discontinuous superprism effect occurs at normal frequencies higher than one, which is due to an abrupt transition between two modes with the refraction angles of opposite signs. The effect can be exploited for switching applications as demonstrated in the paper.     

Band gap studies of 2D photonic crystals with hybrid scatterers

Two-dimensional (2D) photonic crystals (PCs) of a square lattice with dielectric hybrid rods in air are proposed; these PCs consist of a square rod at the center of the unit cell and additional circular rods with their outermost edges against the middle of each side of the lattice unit cell. The band gap structures of PCs can be tailored and optimized by rotating the square rods and adding circular rods to the lattice unit cell. The variation of bands near the complete photonic band gap boundaries, due to some specific modes, is sensitive to certain structural parameters of the system. The results can be understood by analyzing the spatial energy distribution of the electromagnetic fields. Based on such a field analysis, a novel interpretative model is proposed. The PC can be fabricated easily and operated in the microwave region and, hence, should be suitable for applications in new microwave devices.     

一维电介质-金属光子晶体的光学特性研究

利用传输矩阵方法,研究了一维电介质-金属光子晶体的光学特性,该光子晶体通过在Si/SiO₂组成的电介质型光子晶体中插入一定厚度Al层形成。计算结果表明,金属层的引入可以有效提高反射效率,[Si(46 nm)/SiO₂(60 nm)/Al(10 nm)/SiO₂(60 nm)]5结构的单位周期传输衰减从[Si(46 nm)/SiO₂(120 nm)]5的7.2 dB增大到了20 dB;可以得到更宽频率范围的全方向反射带隙,例如[Si(46 nm)/SiO₂(60 nm)/Al(30 nm)/SiO₂(60 nm)]5结构即可提供550 nm带宽的全方向反射;同时讨论了金属吸收、金属层厚度及插入位置对其光学特性的影响。这种电介质-金属光子晶体有望作为性能优异的光学反射镜得到应用。     

Properties of defect modes in one-dimensional symmetric defective photonic crystals

We theoretically investigate the properties of defect modes in one-dimensional symmetric defective photonic crystals. We consider three defective photonic crystal structures, air/[(AB)^NsA^α(BA)^Ns]^Np/air, air/[(AB)^NsAB^βA(BA)^Ns]^Np/air, and air/{[(AB)^NsAB^βA(BA)^Ns]B^γ}^Np−1[(AB)^NsAB^βA(BA)^Ns]/air, where A and B are respectively taken to be the high- and low-index dielectric materials. The first has a defect layer of A^α, the second has a composite defect, AB^βA, and the third has a interleaving defect B^γ. The effect of thickness on the defect mode is studied by varying the parameters α, β, and γ, respectively, for the above model structures. It is found that the positions and the number of defect modes can be significantly changed due to the change in the defect thickness. In addition, by increasing the repeated number N_p, we can have multiple defect modes, leading to a possible design of tunable multichannel filter.     

一维和二维系统中电子禁带与光子禁带的数学等价特性

论证了在不针对特殊的结构和未做任何近似的情况下,一维和二维系统中的电子的Schrdinger方程和沿垂直方向传播的S极化光子的Maxwell方程具有完全相同的数学形式,即二者在数学上是完全等价的,这自然解释了到目前为止发现的存在于电子晶体的电子禁带和光子晶体的光子禁带之间的许多相似性.这种等价性还表明,在电子晶体中出现的许多现象可以推广到光子晶体中;研究电子晶体的理论和方法也可以应用于光子晶体的研究中去.     

Microcavity filters based on hexagonal lattice 2-D photonic crystal structures embedded in ridge waveguides

Two-dimensionally periodic photonic crystal microcavity filters in a ridge waveguide format have been designed and fabricated. Transition mode-matching features were added to increase the optical throughput by more than a factor of two. An increase of Q-factor (more than 100%) was achieved by the addition of two further rows of photonic crystal holes to the microcavity filters. Attempts have also been made to tailor the filter response by applying design concepts used in other Bragg-grating optical filter technologies.     

Novel optical modulator using silicon photonic crystals

We propose a novel compact and integrated optical modulator, which consists of p–i–n silicon photonic crystals with triangular lattice and a line defect waveguide. The device operation is based on a dynamic shift of the photonic band gap (PBG), which induced change in the silicon refractive index by the free carrier injection. We have numerically analyzed and investigated its light modulation performance by using plane wave expansion (PWE) method and finite-difference time-domain method. With small size, rapid response time and high extinct ratio, the designed optical modulator can be used in photonic integrated circuits.     

Photonic crystal beam splitters

In this work, the beam splitter with two input ports and two output ports in two-dimensional photonic crystals is studied through the finite-difference time-domain method. The beam splitter consists of two orthogonally cross line defects. The diameter of the two diagonal air holes at the intersection of the two line defects was modified. The input light can be identically divided into the two output ports. The beam splitters can be applied in the photonic crystal Mach-Zehnder interferometers or photonic crystal optical switches.     

A detailed derivation of eigenvalue equation in two dimensional and three dimensional photonic crystals

A detailed derivation of eigenvalue equation in two dimensional and three dimensional photonic crystals is given by the plane-wave expansion method. Some mathematical formulas such as the rotation of vector, the gradient of scalar, the divergence of the vector, the vector triple product and the conversion between scalar and vector are employed. The eigenvalue equation in photonic crystals has become the important base for obtaining the band structure and the distribution of eigenmode.     

Fabrication and characterization of three-dimensional metallodielectric photonic crystals for infrared spectral region

We propose a technique for the realization of three-dimensional metallodielectric photonic crystals based on fabricating polymeric structures using the interference lithography followed by the magnetron deposition of a gold nanolayer. The infrared reflectance spectra of the fabricated photonic crystals are studied. The spectrometry and finite-difference time-domain modeling data show that there is a photonic band gap centered at the wavelength approximately equal to the photonic crystal period.