轴向隐失波激励的回音壁模式光纤激光器

采用轴向隐失波激励增益的方式,使激光增益区域局限在光纤回音壁模式的模场区域内,显著地降低了回音壁模式光纤激光辐射的抽运阈值,由此形成一种低阈值的回音壁模式光纤激光器.在微焦耳量级的低抽运能量条件下,用回音壁模式光纤激光器研究了激光染料的浓度效应.实验结果表明,随着激光染料浓度的增加,回音壁模式激光辐射的波长向长波方向移动,激光波长范围变宽.用回音壁模式染料激光的四能级模型得到激光上能级和所有能级上的分子数比值γ(λ)曲线后,很好地解释了实验结果.低抽运阈值的回音壁模式光纤激光器,为研究液体激光现象提供了极为便利的手段.     

光纤回音壁模式的三波段激光辐射研究

将石英光纤浸入低折射率的激光染料溶液中构成圆柱形微腔.采用沿光纤轴向光抽运的消逝波激励增益方式,获得了沿光纤轴向长距离的激光染料增益,受激辐射光在圆柱形微腔中回音壁模式的支持下形成激光振荡.在直径为288 μm的同一根光纤外分三段分别填入罗丹明6G、罗丹明610和罗丹明640激光染料乙二醇溶液,实现了波长分别在567～575 nm、605～614 nm和656～666 nm三个不同波段的回音壁模式激光振荡,用一根光纤同时获得了红、橙、黄三种不同颜色的激光辐射.对实验所获得的回音壁模式激光光谱做了模式标定,依据标定的模式数计算了各种模式以及抽运光在光纤截面的强度分布.计算结果表明,激光增益区域总是局限在圆柱形微腔回音壁模式的模场区域内,由此可以显著地提高抽运效率,增加抽运光沿光纤轴向的增益长度.     

回音壁模式光纤激光器的阈值特性研究

研究了一种新型光纤激光器——消逝波激励的回音壁模式光纤激光器的阈值特性.将不同直径的石英光纤分别浸入低折射率的罗丹明6G乙醇和乙二醇混合溶液中,采用沿光纤轴向光抽运消逝波激励染料增益的方式,发现回音壁模式光纤激光辐射的阈值能量和混合溶液的折射率存在不同的依赖关系.随折射率的增加,对小直径光纤,阈值能量随之增加;对大直径光纤,阈值能量单调缓慢递减;对直径适中的光纤,阈值能量先减后增,存在一个和最小阈值能量对应的最佳折射率.用消逝波激励的回音壁模式激光理论,导出了回音壁模式光纤激光的阈值能量公式.理论计算曲线 关键词： 光纤激光器 回音壁模式 激光阈值 消逝波     

消逝波激励的双波段光纤回音壁模式激光辐射

将石英光纤浸入低折射率的染料溶液中后构成圆柱形微腔.采用轴向光抽运消逝波激励激光增益的方式,使增益区域局限在圆柱形微腔回音壁模式的模场区域内,由此显著地提高了抽运效率,增加了沿光纤轴向的增益长度.在一根石英光纤的轴向分段填入浓度同为2×10^-3mol/L的罗丹明6G和罗丹明B乙醇溶液,在567—576nm 和592—600nm的两个波长范围内同时获得回音壁模式的激光辐射;分段填入浓度为8×10^-4和8×10^-3mol/L的罗丹明B乙醇溶液, 关键词： 消逝波激励 圆柱形微腔 回音壁模式 双波段激光辐射     

光纤回音壁模式激光产生长度的实验与理论研究

采用沿光纤轴向光抽运消逝场激励增益的方式,获得了沿光纤轴向较长范围的回音壁模式激光辐射.研究了这种激光器的激光产生长度与抽运能量间的关系.实验发现:当抽运能量刚超过激光产生阈值时,激光产生长度迅速增长;随抽运能量的继续增加,产生长度的增长趋势变缓;产生长度随抽运能量的变化关系决定于增益包层溶液的染料浓度和溶液折射率.根据抽运光沿光纤轴向以受抑全反射方式传播的物理特性,在抽运能量中引入了遵循比尔吸收定律的指数衰减函数,结合消逝场激励增益的回音壁模式激光理论,在分析系统增益和损耗的基础上由激光阈值条件推导出了 关键词： 回音壁模式 受抑全反射 消逝场 激光产生长度     

染料掺杂液晶填充毛细管的激光发射特性研究

本文提出利用染料掺杂液晶填充PI光控取向膜毛细管获得可调谐激光.采用532 nm YAG倍频脉冲激光器抽运,实验及理论研究了有聚酰亚胺(PI)取向膜和无PI取向膜毛细管的激光发射特性,对比分析了两种情形的激光产生阈值以及随温度变化的特性.结果表明:经PI光控取向处理的染料掺杂胆甾相液晶毛细管的激光发射模式具有分布反馈模式和回音壁模式,同时,激光产生阈值为4.5 m J·mm~(-2);发现当温度升高时,发射光谱发生"蓝移",中心波长调谐范围为5.9 nm,温度升高到43℃时,形成质量非常好的回音壁模式,其自由光谱范围为1.05 nm.经PI光控取向处理的染料掺杂向列相液晶激光发射模式为随机激光,并且较无PI取向时激光发射峰减少.     

倏逝波抽运的回音壁模式激光增益计算

倏逝波抽运条件下的回音壁模式光纤激光器增益计算,涉及抽运光束在光纤内的角度分布函数及其数值计算。基于射线光学理论,推导出了高斯分布光束及均匀分布光束经透镜耦合后在光纤内表面的角度分布函数;采用复合辛普生数值积分公式对分布函数进行了数值计算,并用分布函数计算的结果研究了抽运光沿光纤轴向以受抑全反射方式传播时产生的回音壁模式激光的增益特性。所得结果对这类光纤激光器的研究具有理论和实验参考价值。     

基于非线性偏振旋转效应的多波长光纤激光器

多波长光纤激光器是未来波分复用光通信系统的理想光源,提出和展示了一个基于非线性偏振旋转效应的多波长光纤激光器,非线性偏振旋转诱导的强度相关非均匀损耗能有效地抑制均匀加宽增益介质掺铒光纤中的模式竞争,从而使光纤激光器在室温下产生稳定的多波长输出,实验实现了最多18个波长的多波长输出.另外,此激光器没有使用传统的滤波器,而是在激光腔内插入一段保偏光纤,保偏光纤与偏振相关隔离器构成一等效Lyot双折射光纤周期性滤波器.利用这种在线型的双折射光纤滤波器简化了光纤激光器的结构,使它更易于集成.还实验研究了多波长输出随抽运功率的演化,发现抽运功率对多波长的均匀性影响很大.     

一种新型自激发布里渊掺铒光纤激光器

利用级联的受激布里渊效应,自激发布里渊掺铒光纤激光器可以实现常温下的多波长激光输出。通过在自激发掺铒光纤激光器中引入一个高双折射萨尼亚克(Sagnac)环形滤波器,调节萨尼亚克环形滤波器的偏振控制器(PC),实现了可调谐多波长输出,同时在实验中观测到双布里渊多波长带的现象。研究了这种光纤激光器中萨尼亚克环形滤波器的带宽和980 nm抽运光功率对输出波长数的影响,在萨尼亚克环形滤波器的带宽为83.3 nm以及980 nm抽运光功率为260 mW时,得到了52个间隔为0.088 nm的多波长激光输出。     

具有非均匀零色散波长光纤中的四波混频

提出了一种分析具有非均匀零色散波长光纤中四波混频(FWM)的简便方法,导出了多段不同零色散波长组成的光纤中和零色散波长连续变化的光纤中四波混频效率的计算公式.实例计算结果表明,光纤中零色散波长分布的不均匀,会影响四波混频效率,特别是在抽运光和检测光波长间隔较大时,影响尤为显著. 关键词： 四波混频 相位匹配 零色散波长     

Linearly polarised three-colour lasing emission from an evanescent wave pumped and gain coupled fibre laser

A novel Whispering--Gallery--Mode (WGM) fibre laser, emitting linearly polarised three-colour light, is demonstrated by pumping and gain coupling with evanescent waves. The pump light is longitudinally coupled into a bare optical fibre immersed in a dye solution of lower refractive index. The dye molecules around the bare fibre are excited by the evanescent waves of pump light when they propagate along the fibre in a total internal reflection. When the pump beam within the fibre is a meridian beam, the WGM lasing emission from the fibre laser is a linearly polarised transverse electric wave, while it is a mixed wave of the linearly polarised transverse electric and magnetic waves if the pump beam is a skew beam within the fibre. Because the excited molecules are located within the evanescent field of WGM, a good spatial overlap between the dye gain and the evanescent field leads to a high pumping efficiency and a longer gain distance along the fibre. Once the bare fibre is inserted into three glass capillaries filled with Rhodamine 6G, 610 and 640 dye solutions, respectively, WGM laser oscillations at the wavelengths of 567--575, 605--614 and 656--666~nm occur simultaneously, and a linearly polarised three-colour lasing emission is achieved in a single optical fibre.     

激光入射角度对薄膜热场分布影响的数值分析

在多层介质薄膜中，激光的入射方式是影响薄膜抗损伤能力的关键因素之一.提出了一种模拟锥角高斯光入射多层介质薄膜后电场和热场分布的方法.该方法能够分析薄膜中高斯光各个角谱分量叠加形成的电场分布，进而得到由于薄膜本征吸收产生的热量沉积以及薄膜内部的温度场分布.针对中心波长为4.3 μm的中红外高反膜进行了分析，给出了高反膜系的温升峰值随激光入射角度和偏振态的变化.结果表明：对于s偏振光，斜入射时膜系的最高温升峰值高于垂直入射峰值，而p光的结果则相反.此种模拟方法克服了原有方法对激光入射角度的限制，较好地反映出斜入射情况下激光偏振态对薄膜损伤的影响. 关键词： 多层介质薄膜 高斯光 热过程 数值分析     

Chaos synchronization in semiconductor lasers with polarization-rotated optical feedback

Chaotic oscillations of the transverse magnetic (TM) mode, which is not a common lasing mode, are excited by using polarization-rotated optical feedback from the transverse electric (TE) mode in a semiconductor laser. In our previous paper, we found that the dynamics were strongly dependent on their RF components under the condition of moderate optical feedback from the TE mode to the TM mode and that they were divided into three RF regions; low-pass filtered signals with a lower frequency than the laser relaxation oscillation frequency, intermediate RF components including the relaxation oscillation frequency, and high-pass filtered signals with a higher frequency higher than the relaxation oscillation frequency. Depending on the frequency bands, the laser outputs showed different correlations. In the present study, using such schemes, the polarization-rotated beam from a transmitter laser (i.e., the rotated TE-mode beam of a transmitter laser) is injected into a receiver laser. We experimentally observe chaos synchronization in accordance with the dynamics of RF components on the transmitter laser side. We also perform numerical calculations using a model and obtain good agreement between the theoretical and experimental results.     

Beat excitation of terahertz radiation in a semiconductor slab in a magnetic field

Two infrared lasers of frequencies ω₁ and ω₂ propagating in the TM/TE mode along $\stackrel{?}{z}$ direction in a rippled density semiconductor waveguide are shown to resonantly excite terahertz radiation at the beat frequency when ripple wave number is suitably chosen to satisfy the phase matching. The wave vector of the density ripple is along the direction of laser propagation while a static magnetic field is applied transverse to it. The lasers exert a ponderomotive force on the electrons at the beat frequency. This force, in the presence of density ripple and transverse magnetic field, produces a nonlinear current at the terahertz frequency. The magnetic field enhances the amplitude of the terahertz wave. However terahertz yield is significantly higher in the TM mode laser beating than in the TE mode laser beating.     

Characteristics of whispering-gallery-mode dye lasers utilizing dye-doped solid microspheres by UV N2-laser pumping

The characteristics of a whispering-gallery-mode (WGM) dye laser using a variety of dye-doped solid microspheres, pumped by a UV N₂-laser, are presented. Experimental results for the WGM dye laser are presented with the spatial distribution and spectral and temporal responses of lasing. The spectral response of a new variety of WGM dye laser is in the blue-green or red spectral regions, and over a wide spectral range.     

Cavity-Q-driven phenomena in an evanescent-wave pumped and gain coupled whispering-gallery-mode fiber laser

We study cavity-Q-driven lasing wavelength shift and line-width widening in an evanescent-wave pumped and gain coupled Whispering-Gallery-Mode (WGM) fiber lasers. A bare optical fiber is immersed in a lower refractive index (RI) dye solution, pumped and gain coupled by evanescence waves, and linearly polarized WGM lasing emission is observed from the rim of the fiber. We find that both lasing wavelengths and line width of WGM peaks are sensitive to the RI of the dye solution and the fiber diameter, with the increase of the RI of the dye solution or decrease of the fiber diameter, a blue shift of the lasing spectrum and a widening on the spectral line width are observed. The observed phenomena have been attributed to the change of quality factor of a circular cavity built in the fiber cross section, the achieved experimental data agree well with the calculated values of the quality factor.     

柱形微腔回音壁激光光谱模式的精确标定

由柱形微腔中回音壁模式满足的本征值方程,得到确定回音壁模式位置和间距的近似解析公式。以此近似解析公式,首次对直径在215～328 μm间的5个柱形微腔回音壁激光光谱做了模式标定。在用近似解析公式对柱形微腔激光光谱的数值作拟合的计算中,除了回音壁模的径向模式数(l)和角动量模式数(n)外无需其他拟合参数,解析公式的拟合值和实验激光光谱波长值间的偏差小于0.05 nm,拟合结果精确可靠。柱形微腔回音壁激光光谱模式的精确标定在模式的场分布计算以及频移型微腔生物传感器的研究应用中具有重要作用,文章介绍的方法亦可应用于柱形微腔直径和折射率的精密测量。