基于局域表面等离子体共振效应的聚合物波导传感器特性研究

以SU-8光刻胶作为波导芯层材料,设计了基于金纳米粒子的局域表面等离子体共振(LSPR)波导传感器。根据Mie理论,建立了金纳米粒子的消光模型,理论分析了纳米粒子半径、待测物折射率等因素对局域表面等离子体共振曲线的影响。分析表明:当待测液体折射率增大时,LSPR共振峰的位置发生红移。随着金纳米粒子半径的逐渐增大,传感器灵敏度增加。共振吸收峰逐渐由单峰变为双峰,其中一个峰位于520 nm波长附近,主要由表面等离子体吸收造成;另一个峰随金纳米粒子半径的增大而逐渐红移,主要由表面等离子体散射造成。     

金属复合纳米粒子的局域表面等离子体特性研究

提出了一种在银层上面覆盖一层金的四棱台复合纳米结构。采用离散偶极子近似(DDA)方法,针对光激发复合金属纳米粒子的局域表面等离子体共振(LSPR)进行研究,讨论了四棱台纳米粒子金银复合结构在不同尺寸、不同混合比等条件下的消光特性及折射率灵敏度。计算结果显示,在银层厚度为50 nm的四棱台纳米粒子上覆盖金层,其折射率灵敏度不变。同时,四棱台银纳米粒子厚度的增加会使其消光峰值波长蓝移。金材料比例的增加会使金银复合纳米结构的消光峰值波长红移。当金银复合结构的纳米粒子的厚度大于自由电子的平均自由程时,其局域表面等离子体激发强度不发生变化。     

利用Ag@SiO_2纳米粒子等离子体共振增强发光二极管辐射功率的数值研究

金属纳米粒子利用其局域表面等离子体共振效应(LSPR),可以增强附近荧光分子的自发辐射速率,因而在光学传感、光电器件等领域中具有潜在的应用价值.金属纳米粒子的LSPR与其自身的材料、形状、尺寸以及周围环境介质密切相关,这影响着纳米粒子在具体器件中的应用.本文利用三维时域有限差分法,研究了相同体积的球形、椭球形、立方形与三棱柱形银纳米粒子对薄膜发光二极管辐射功率的影响;计算了不同形状银纳米粒子对偶极子光源辐射功率和薄膜器件光出射强度的增强,并结合LSPR效应讨论了辐射功率变化的物理机理.研究结果表明:银纳米粒子自身形状尖锐程度的增加有利于提高LSPR的共振强度;同时纳米粒子的形状影响了LSPR共振电场与薄膜器件中偶极子辐射电场之间的耦合作用,其中立方形纳米粒子因为能实现最强的耦合作用而对器件的辐射功率增强最大.在此基础上进一步讨论了不同薄膜材料对LSPR共振及光源辐射功率的影响,发现较高的材料折射率有利于增强金属纳米粒子的LSPR与器件的耦合作用,从而改善发光二极管性能.     

金属纳米颗粒光学性质的离散偶极近似计算

采用离散偶极子近似(DDA)方法,研究了单体银纳米粒子和银纳米粒子阵列的光谱特性。研究结果发现,单体银纳米粒子的表面等离子体共振消光峰的位置随着周围介质折射率和粒子尺寸的增大逐渐红移,并且消光光谱的峰宽也越来越大。当银纳米粒子正方阵列的周期接近单体的共振波长时,阵列的消光光谱中会出现尖锐的共振峰,改变粒子尺寸的大小可以发现消光光谱中共振峰的峰值和位置有大幅度地改变,通过改变阵列在平行和垂直于入射光偏振方向上的周期,可以调节二维长方阵列共振峰的峰宽和峰位。该研究为纳米粒子在光学显微镜、生物传感元件、数据存储等领域中的应用提供有效地理论参考。     

单芯帽纳米颗粒的光学性质

基于三维时域有限差分法,计算了非球对称单芯帽纳米颗粒在不同结构参数作用下的局域表面等离子体共振(LSPR)响应。采用模板法和真空蒸镀技术制备了SiO_2@Au芯帽结构纳米颗粒,通过透射电子显微镜和紫外可见近红外分光光度计对其形貌和光学性质进行了测量分析,获得了金壳厚度、芯壳比、芯径和金属表面覆盖率等纳米结构参数对LSPR峰值吸收波长和吸收截面的影响规律。结果表明,芯帽纳米颗粒结构参数的微小改变会导致LSPR峰在可见光到近红外波段的宽带红移。     

菱形金属纳米粒子光学性质的研究

金属纳米粒子的光学性质与金属纳米粒子的组成、形状、尺寸及周围的介电常数有关。利用时域有限差分法研究菱形纳米粒子的尺寸与其消光特性关系, 发现粒子尺寸的大小对其消光谱共振峰有较大影响, 随着粒子尺寸的增大, 消光谱共振峰可分裂成两个或多个共振峰。而且在可见光范围内波长大于480 nm的区域, 表面等离子体共振峰是偶极子激发模式; 而在波长小于480 nm的区域, 共振模式则比较复杂, 有偶极子模式, 也有多极子模式。计算表明, 波长为480~ 600 nm区间与波长大于600 nm的区间, 菱形纳米粒子的尺寸对消光光谱的峰值和谱线宽度影响不同。在波长为480~600 nm之间, 短轴为140 nm时, 其消光效率最高。     

消光式核壳二聚体传感器的设计与光谱特性分析

根据ITO/Au纳米核壳二聚体粒子在生物医学领域的应用合理性,设计了一种实时检测生物液体的核壳二聚体探针消光式传感器;由偶极子理论推导出输出波长与外界环境折射率关系;利用MATLAB设计ITO/Au纳米核壳二聚体粒子结构;采用软件DDSCAT7.3结合离散偶极近似法,利用二聚体有效半径模拟计算了300~950nm可见光到红外光波段不同核壳比、二聚体间距、以及不同介质折射率的消光光谱;根据传感芯片折射率与偶极共振、耦合八级共振的响应关系得出ITO/Au二聚体的折射率灵敏特性。与传统Ag/Au核壳纳米粒子相比,ITO/Au纳米核壳二聚体结构引入了可作为传感芯片灵敏性自参考参数的耦合八级共振峰,同时ITO/Au二聚体结构的折射率灵敏度可达到419nm/RIU。这些工作及其结果对制作消光式传感器具有重要的意义。     

不同单体形状生物粒子凝聚体消光特性的差异分析

针对生物粒子凝聚体单体形状和光学特性的复杂多变,构建了5种不同单体形状的生物粒子凝聚体空间结构,并用离散偶极子近似方法计算了生物粒子凝聚体的消光特性参数,分析了不同单体形状生物粒子凝聚体的消光特性差异。计算结果表明：非球形生物粒子凝聚体在将其单体形状等效为球形时,平均质量消光系数的相对偏差绝对值在6%以内;不同单体形状生物粒子凝聚体对光的散射能力不同是消光特性存在差异的主要表现,且通常情况下单体形状越偏离球形,相对偏差越大,因此,由不同单体形状引起的消光特性的差异不应被忽略。此项工作可应用于准确评估和优化生物粒子材料的消光性能。     

Slot结构聚合物波导微环光学生物传感器研究

Slot结构在提高集成波导光学传感器灵敏度和降低探测极限值方面具有极大的优势。对基于Slot结构的聚合物PSQ-Ls波导微环光学生物传感器进行了研究。分析了850 nm波段Slot波导的单波导高度、狭缝宽度及单波导宽度对传感器灵敏度的影响,在满足单模传输的条件下,得到了优化的微环传感器横截面尺寸参数。对Slot结构波导微环的弯曲损耗、自由光谱范围等进行了仿真分析,得到微环传感器的消光比、品质因子等随结构参数的变化,确定了优化的微环弯曲半径、耦合效率。与正脊形结构波导微环传感器相比,Slot结构波导微环传感器的灵敏度是前者的两倍,探测极限值是其一半。     

用于下一代传感和光源的新型材料、光纤及器件

制造技术与复杂模型、设计工具的进步使微纳结构光学器件的实现成为可能。微纳结构光学器件可用于导光与光的相互作用,液态或气态新型光源和传感器件。IPAS致力于新型光学材料研究与开发,将玻璃工艺和光纤开发有机结合,重点研究微纳结构光纤,光纤表面功能处理和器件开发。介绍了IPAS的研究实力和近年的发展概况,其中包括中红外光学材料、纳米粒子嵌入玻璃材料、新型化学和生物传感器(适用于超低量样本及/或体内样本)、激光器件,以及用于光数据处理的新型高非线性光纤。     

Laser-Scanning Microscopy for Electrophoretic Mobility Characterization of Single Nanoparticles

To enable detailed studies of interactions between nanoparticles and their environment and the correlations between various nanoparticle properties, one must go beyond ensemble averages and toward single-particle measurements. However, current methodologies for the single-nanoparticle analysis of charge and size either lack the flexibility to study dynamic processes on the single-particle level or are highly specific and require complex microfluidic devices. In addition, accurate measurements of the electrophoretic mobility (or zeta-potential) based on the optical detection of single nanoparticles remain challenging due to the low photon budget, the required sampling frequency, and the fact that electroosmosis in typical microfluidic devices must be analyzed carefully. In this study, a method is investigated to accurately characterize the electrophoretic mobility of individual nanoparticles and estimate their size by simultaneously analyzing the electrokinetic- and Brownian motion in a simple microfluidic channel. Fast laser scanning excitation and sensitive detection of fluorescent photons enable single-nanoparticle velocimetry experiments in an oscillating electric field at high frame rates.     

Theoretical near-field optical properties of branched plasmonic nanoparticle networks

Extended branched networks of single-nanoparticle chains have recently been self-assembled from colloidal suspensions. In particular, gold nanoparticle linear chains and complex chain networks have revealed unique signatures of plasmon modes in their extinction spectra. In this Letter, we investigate theoretically their near-field optical properties and show that a real space mapping of these modes can be achieved with a photon scanning tunneling microscope setup. A distinct subwavelength patterning of the optical near-field gives rise to well-resolved photon scanning tunneling microscope images that can be used to identify the network segments able to efficiently carry optical energy.     

Localized surface plasmon resonance scattering imaging and spectroscopy for real-time reaction monitoring

Abstract

In the last decade, plasmonic nanoparticles-based scattering imaging and spectroscopy has introduced the analysis and sensing to the single nanoparticle and molecule level, such as the biomolecules adsorption process and the quantitative detection of small molecules and ions. Recently, this technology has also been focus on the real-time and in-situ reaction monitoring, which is a new emerging branch of the single-nanoparticle imaging, revealing the reaction dynamic information and the related controlling factors. In this mini-review, recent applications of plasmon resonance scattering imaging and spectroscopy in the real-time reaction monitoring in the past 5?years are highlighted and discussed.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Effect of nanostructured MoS2 morphology on the glucose sensing of electrochemical biosensors

In this study, the effects of the morphological characteristics of MoS₂ nanomaterials on the glucose sensing of electrochemical biosensors were explored. Nanostructured MoS₂ materials, including nanoparticles (NPs), nanoflowers (NFs), and nanoplatelets (NPLs), were prepared via a simple hydrothermal method. The structure and morphological characteristics of MoS₂ nanomaterials were examined through X-ray diffraction, field emission scanning electron microscopy, and Raman spectroscopy. Electrochemical properties were analyzed through cyclic voltammetry. Results showed that the obtained sensitivity was 64, 68.7, and 77.6 μAmM⁻¹ cm⁻² for MoS₂ NP-, MoS₂ NF-, and MoS₂ NPL-based biosensors, respectively. The limit of detection (LOD) of all MoS₂-based glucose biosensors was 0.081 mM. In addition, the pH, temperature, glucose oxidase (GOx) concentration, reproducibility, specificity, and stability of glucose biosensors with different MoS₂ morphologies were also investigated and indicated the oxidation current response of the MoS₂ NPL-based glucose biosensor was higher than that of MoS₂ NF- and NP-based biosensors.     

Genetically modified organism (GMO) detection by biosensor based on SWCNT material

This paper reports single-walled carbon nanotube-based biosensors for genetically modified organism (GMO) detection. Electrochemical electrode and single-walled carbon nanotube field effect transistor (SWCNT-FET)-based biosensors are used to determine the CaMV 35S promoter of Roundup Ready soybean. Given optimal conditions, both biosensors can effectively detect full complementarity with concentration as low as 1 nM. The sensitivity of the electrode-based biosensor is approximately 0.6 kΩ/nM while that of the SWCNT-FET-based biosensor is 0.32 nA/nM. Both biosensors were also used to determine a polymerase chain reaction-amplified sample. The obtained results showed that both sensors determined transgenic organisms well, thereby providing a useful tool for screening analysis of food samples.     

Optical biosensor with dispersion compensation

Dispersion limits performance in many optical systems. In surface plasmon resonance (SPR) biosensors, the sensing area is an optical element in which the dispersion depends on the effective refractive index of the biochemical compounds to be measured. We report a method of compensating for wavelength dispersion in SPR biosensors employing two integrated diffractive optical coupling elements in a polymer substrate. The dispersion compensation is achieved over the whole dynamic measurement range and provides a biosensor more robust to wavelength fluctuations than prism-coupler SPR systems. The concept can readily be employed in other types of sensor measuring refractive-index changes.     

表面等离激元共振生物传感分析及应用

基于物理中发生在金属表面的表面等离激元现象 ,阐述表面等离激元共振生物传感分析原理 ;进而建立表面等离激元共振生物传感成像。给出应用表面等离激元共振研究生物单元相互作用的实例。     

An experimental correlation study between field–target overlap and sensitivity of surface plasmon resonance biosensors based on sandwiched immunoassays

In this report, we have studied the effectiveness of field–target overlap to evaluate detection sensitivity of surface plasmon resonance (SPR) biosensors. The investigation used theoretical analysis based on the transfer matrix method, which was experimentally confirmed by thin film-based detection in sandwich and reverse sandwich immunoglobulin G (IgG) assays. Both theoretical and experimental results show that strong correlation exists between the overlap and the sensitivity with the coefficient of correlation higher than 95% in all the cases that we have considered. We have also confirmed the correlation in diffraction grating-based SPR measurement of IgG/anti-IgG interactions. The correlation elucidates the mechanism behind the far-field detection sensitivity of SPR biosensors and can lead to the enhancement of SPR biosensing with molecular scale sensitivity.     

Characterization of immobilization methods of antiviral antibodies in serum for electrochemical biosensors

In this paper, we describes different methods to immobilize Japanese encephalitis virus (JEV) antibodies in human serum onto the interdigitated surface of a microelectrode sensor for optimizing electrochemical detection: (1) direct covalent binding to the silanized surface, (2) binding to the silanized surface via a cross-linker of glutaraldehyde (GA), (3) binding to glutaraldehyde/silanized surface via goat anti-human IgG polyclonal antibody and (4) binding to glutaraldehyde/silanized surface via protein A (PrA). Field emission scanning electron microscopy, Fourier transform infrared spectrometry, and fluorescence microscopy are used to verify the characteristics of antibodies on the interdigitated surface after the serum antibodies immobilization. The analyzed results indicate that the use of protein A is an effective choice for immobilization and orientation of antibodies in serum for electrochemical biosensors. This study provides an advantageous immobilization method of serum containing antiviral antibodies to develop electrochemical biosensors for preliminary screening of viruses in clinical samples from outbreaks.