Novel optic-fiber switches based on the wobble-type MEMS electromagnetic microactuator

Some novel optic-fiber switches based on an MEMS electromagnetic microactuator are developed in this paper and their design, fabrication and performance are described. A new kind of wobble-type MEMS electromagnetic microactuator is successfully developed, which can drive mirrors to enter or leave the optical path of a switch. It is layered, composed of two stators and one wobble disc, which improve the output torque of the actuator. Finally, 1×2, 2×2, 1×4 and 1×8 single mode optic-fiber switches, which have been fabricated, are measured. The operating voltage is less than 8 V, switching time is less than 5 ms, insertion loss is less than 0.8 dB, crosstalk is 60 dB, and extinction ratio is 60 dB. These optic-fiber switches show a promising future in optical fiber communication systems.     

The Landau gauge gluon propagator in lattice QCD

A Monte Carlo calculation of the gluon propagator in the Landau gauge in SU(3) lattice gauge theory is described. The results of calculations at β = 5.6 (200 4³ × 8 lattices), β = 5.8 (400 4³ × 10 lattices and 100 6³ × 12 lattices), and β = 6.0 (100 4³ × 8 lattices) indicate that the gluon propagator resembles a massive particle propagator in which the mass grows with separation. At the largest distances accessible with these lattices, the mass is about 600 MeV.     

微变形镜在自适应光学中的应用与发展

自适应光学系统主要用于校正由大气湍流等引起的波前畸变,经过半个多世纪的发展,自适应光学系统已经应用到了许多领域。传统自适应光学系统中的变形镜在许多情况下已经不能满足自适应光学新发展的需要。随着微制造技术的发展,用微制造技术制作的新型微变形镜大大提高了致动单元的集成度,简化了电源,提高了可靠性,降低了自适应光学系统的体积和造价。综述了微变形镜技术的发展情况及其在自适应光学中的应用,并且讨论了其发展前景。     

Development of a compact on-beam SEOP neutron spin filter

We have designed and demonstrated a prototype on-beam spin-exchange optical pumping (SEOP) ³He neutron spin filter (NSF). It is designed as the incident neutron polarizer for spallation neutron sources, where the installation space is limited due to thick radiation shielding. The size of the NSF is roughly 50 cm×50 cm×25 cm including the diode-laser optics with a frequency narrowing external cavity, and a cylindrical ³He cell as large as a diameter of 5 cm and a length of 10 cm can fit. A neutron beam test was performed at the NOP beamline of JRR-3 to see the performance of the NSF.     

同步辐射中双压电片反射镜的研究现状

反射镜是同步辐射光束线中应用广泛的光学元件之一,双压电片反射镜由于具有结构简单、面形能动以及自适应可调等优点,逐渐引起同步辐射界的重视.本文综述了同步辐射中双压电片反射镜的研究现状.主要讨论了双压电片反射镜的工作原理和研究概况,包括在几个大型同步辐射装置中的结构特点、制备技术及面形校正结果等;简要介绍了双压电片反射镜面形校正时所采用的反射波前探测技术和反馈控制算法;最后总结了其发展中存在的关键问题,并展望了其未来的发展方向.     

Fast-acting adaptive mirrors and their efficiency at compensating for random phase perturbations

Research in adaptive optics represents a new stage in the development of optical systems. Adaptive optics can be used for compensating for phase fluctuations of a light field propagated through the atmosphere and through optical media. The idea of dynamic compensation of phase fluctuations originated in the 1950s [1] as an effort to improve the resolutions of telescopes designed for observing stars through the turbulent atmosphere. However, the technological level required for applying this technique to detection and transmission systems has only recently been achieved with the successful development of fast-acting optical elements — adaptive mirrors [2].Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 11, pp. 106–117, November, 1985.     

Micro-electro-mechanical deformable mirrors for aberration control in optical systems

Controlling optical aberrations is one of the enduring problems in optics. Recent advances in adaptive optics for astronomical applications have shown the promise of adaptive optics technology for controlling aberrations. Micro-electro-mechanical deformable mirrors (MEM-DMs) offer an alternative to conventional adaptive optics which, due to the inexpensive nature of MEM-DM technology, will enable a wide range of commercial and scientific applications for optical wave front control. In this paper we describe MEM-DMs, present results of modelling the performance of an MEM-DM for optical aberration control, and present results of experiments to verify that MEM-DMs can control optical aberrations.     

Fabrication of nested elliptical KB mirrors using profile coating for synchrotron radiation X-ray focusing

This paper describes fabrication methods used to demonstrate the advantages of nested or Montel optics for micro/nanofocusing of synchrotron X-ray beams. A standard Kirkpatrick-Baez (KB) mirror system uses two separated elliptical mirrors at glancing angles to the X-ray beam and sequentially arranged at 90° to each other to focus X-rays successively in the vertical and horizontal directions. A nested KB mirror system has the two mirrors positioned perpendicular and side-by-side to each other. Compared to a standard KB mirror system, Montel optics can focus a larger divergence and the mirrors can have a shorter focal length. As a result, nested mirrors can be fabricated with improved demagnification factor and ultimately smaller focal spot, than with a standard KB arrangement. The nested system is also more compact with an increased working distance, and is more stable, with reduced complexity of mirror stages. However, although Montel optics is commercially available for laboratory X-ray sources, due to technical difficulties they have not been used to microfocus synchrotron radiation X-rays, where ultra-precise mirror surfaces are essential. The main challenge in adapting nested optics for synchrotron microfocusing is to fabricate mirrors with a precise elliptical surface profile at the very edge where the two mirrors meet and where X-rays scatter. For example, in our application to achieve a sub-micron focus with high efficiency, a surface figure root-mean-square (rms) error on the order of 1 nm is required in the useable area along the X-ray footprint with a ∼0.1 mm-diameter cross section. In this paper we describe promising ways to fabricate precise nested KB mirrors using our profile coating technique and inexpensive flat Si substrates.     

Practical common-path heterodyne surface profiling interferometer with automatic focusing

In modern semiconductor and optics industries, there is a strong demand for a highly sensitive and non-contact surface profilometer. This paper describes a practical heterodyne surface profiling interferometer for on-line non-contact measurement which has been developed recently. The essential feature of the profilometer is a newly designed common-path configuration to minimize the effects caused by vibration, air turbulence and other environmental variations. A single-mode frequency-stabilized laser diode (780 nm) serves as the light source to make the whole system compact (total volume 250L×200W×100H mm). A powerful signal processing scheme is also developed, which includes three parts: automatic voltage control, phase measurement with wide range and automatic focusing control. All these make the repeatability and stability of the profiling interferometer greatly improved. The system has vertical resolution of 0.39 nm and lateral resolution of 0.73 μm. During approximately an hour, the stability is within 1.95 nm(3σ).     

Surface structures of in (√3 × √3 )R30° and (5√3 × 2) phases studied by surface extended X-ray absorption fine structure spectroscopy

The local surface structures of in the ( √3 × √3) R30° and (5√3 × 2) phases have been investigated by means of polarization-dependent sulfur K-edge surface EXAFS. In the (√3 × √3 ) R30° phase, sulfur adatoms are found to occupy threefold hollow sites with a S---Ni distance of 2.13 Å and an inclination angle ω of the Sz.sbnd;Ni bonds at 44° from the surface plane. In contrast, in the (5√3 × 2) phase, it is determined that the Sz.sbnd;Ni bond is longer, 2.18 Å, more inclined, ω = 31°, and that the coordination number is not 3 but 4. These results strongly support a picture involving reconstruction of the top nickel layer to form a rectangular structure. Consideration of several models proposed for the (5√3 × 2) phase leads to one which is compatible with both the present results and results recently reported using STM.     

Efficient generation of blue light by intracavity frequency doubling of a cw Nd:YAG laser with LBO

We report on the efficient room-temperature operation of ⁴F_3/2–⁴I_9/2 transition in a diode pumped Nd:YAG laser operating at 946 nm. An output power of 5.1 W and a slope efficiency of 23.6% at 946 nm have been obtained. Different LBO crystals of length 3×3×10 mm³, 3×3×15 mm³, 3×3×18 mm³ were selected as frequency doubling material for comparison. A maximum single-ended output power of 1.3 W at 473 nm was achieved by frequency doubling with an optical conversion efficiency of 5%. When the Nd:YAG rod was replaced by the one with high reflectivity coating at 473 nm on the pump side, the output power of blue light was almost twice that without high reflectivity coating for 473 nm at the same pump power level. Moreover, the theoretical optimum length of LBO crystal for intracavity frequency doubling was discussed, and the experimental results made a good agreement with it.     

Boron and indium incorporation in GaP(0 0 1) surfaces by vapour deposition: Density-functional supercell calculations of the surface stability

Using surface supercells and the density-functional method, surface formation energies are calculated for probable GaP(0 0 1) reconstructions without and with indium or/and boron substitutions. Obtained surface stability diagrams provide surface compositions and surface structures in dependence on the growth conditions: indium atoms are built into the c(4 × 4) patterns under strongly P-rich conditions and into the β2(2 × 4) reconstruction under less P-rich conditions. Under In-rich and non-P-rich conditions, initial structures of metallic InGa phases are formed in the (2 × 4) mixed-dimer reconstruction. In the c(4 × 4) and (2 × 4) mixed-dimer patterns the full range of In:Ga content is accessible by variation of the In:Ga ratio in the gas phase. Boron can be built into the c(4 × 4) patterns of the GaP(0 0 1) surface in form of isolated atoms or nearest-neighbours under strongly P-rich and moderately to strongly B-rich conditions. The boron incorporation is strongly enhanced at the surface in respect to theoretical predictions for the bulk, what explains the larger content found experimentally. Assuming P-rich conditions, which are suitable for the growth of the ternary alloys, the obtained surface stability diagram for the quaternary (BInGa)P shows that nearly the full range of In:Ga content is accessible. However, the boron content in the alloy is restricted as found analogously for (BGa)P and is independent of the indium content. The expected increase of the boron content in presence of indium cannot be confirmed. Contrary to the analogous GaAs systems, boron atoms do not substitute phosphor atoms (antisite position) in GaP, (InGa)P, (BGa)P, and (BInGa)P.     

Optimum deformable mirror modes for sensorless adaptive optics

Wavefront sensorless adaptive optics schemes rely upon the accurate generation of aberration modes by the adaptive element, usually a deformable mirror. Analytic functions are often used for representation of the aberrations in these systems. Such functions cannot be perfectly reproduced by deformable mirrors and the approximation errors can affect the aberration correction procedure. We derive alternative modal basis sets directly from the actuator influence functions, thus avoiding the approximation errors. We investigate how the choice of aberration modes affects the performance of a sensorless adaptive imaging system. The new modes are found to be most advantageous for deformable mirrors with a small number of actuators.     

Linear quadratic regulator for laser beam shaping

The performance of an adaptive optics system depends on multiple factors, including the quality of the laser beam before being projected to the mesosphere. In general, cumbersome procedures are required to optimize the laser beam in terms of amplitude and phase. However, aberrations produced by the optics of the laser beam system are still detected during the operations due to, for example, uncertainty in the utilized models. In this paper we propose the use of feedback to overcome the presence of model uncertainty and disturbances. In particular we use a Linear Quadratic Regulator (LQR) for closed loop laser beam shaping using a setup of two deformable mirrors. The proposed method is studied and simulated to provide an automatic optimization of the Amplitude of the laser beam. The performance of the LQR control algorithm is evaluated via numerical simulations using the root mean square error (RMSE). The results show an effective amplitude correction of the laser system aberrations after 20 iterations of the algorithm, a RMSE less than 0.7 was obtained, with about 140 actuators per mirror and a separation of z=3 [m] among the mirrors.     

Efficient phase estimation for large-field-of-view adaptive optics

We propose a maximum a posteriori-based estimation of the turbulent phase in a large field of view (FOV) to overcome the anisoplanatism limitation in adaptive optics. We show that, whatever the true atmospheric profile, a small number of equivalent layers (two or three) is required for accurate restoration of the phase in the whole FOV. The implications for multiconjugate adaptive optics are discussed in terms of the number and conjugated heights of the deformable mirrors. The number of guide stars required for wave-front measurements in the field is also discussed: three (or even two) guide stars are sufficient to produce good performance.     

变形镜像差拟合能力的有限元仿真

为了研究变形镜对于Zernike多项式像差模式的拟合能力, 利用有限元仿真方法, 建立了两种不同单元排布方式的变形镜有限元模型. 通过给促动器施加理论位移, 进行了仿真分析. 结果指出了不同的促动器排布方式与像差拟合能力之间的关系, 同时表明57点促动器密布的排列方式已经能校正像差到λ/20甚至更小, 验证了促动器对变形镜“印透效应”等的影响.     

Laser output power over 5 W at 1.06 μm for Nd:GdVO4 single crystal

In this paper, we report the polarization absorption spectra from 400 to 850 nm, polarization emission spectra from 1050 to 1100 nm and laser properties of an Nd:GdVO₄ crystal. An output power of up to 5.29 W at 1.06 μm has been achieved with a 3×3×3 mm Nd:GdVO₄ crystal sample when it is pumped by a cw laser diode.     

Adaptive optics by incoherent digital holography

Adaptive optics in astronomical and other imaging systems allows compensation of aberrations introduced by random variations of the refractive index in the imaging path. I propose what I believe is a new type of adaptive optics system that dispenses with the hardware lenslet arrays and deformable mirrors of conventional systems. Theoretical and experimental studies show that wavefront sensing and compensation can be achieved by numerical processing of digital holograms of the incoherent object and a guide star. The incoherent digital holographic adaptive optics is seen to be particularly robust and efficient, with envisioned applications in astronomical imaging, as well as fluorescence microscopy and remote sensing.     

A core level and valence band photoemission study of the (1 1 1) and ( ) surfaces of 3C–SiC

A core level and valence band photoemission study of thick 3C–SiC(1 1 1) and 3C–SiC( ) epilayers grown by sublimation epitaxy is reported. The as introduced samples show threefold 1×1 low-energy electron diffraction patterns. For the Si face and reconstructed surfaces develop after in situ heating to 1100°C and 1300°C, respectively. For the C face a 3×3 reconstruction form after heating to 980°C. A semiconducting behavior is observed for the and 3×3 reconstructed surfaces while the reconstruction show a Fermi edge and thus a metallic-like behavior. The surface state on the surface is investigated and found to have Λ₁ symmetry and a total band width of 0.10 eV within the first surface Brillouin zone. For the Si 2p and C 1s core levels binding energies and surface shifted components are extracted and compared to earlier reported results for 6H– and 4H–SiC.     

Effect of oxygen partial pressure on the structural and optical properties of dc reactive magnetron sputtered molybdenum oxide films

Molybdenum oxide films (MoO₃) were deposited on glass and crystalline silicon substrates by sputtering of molybdenum target under various oxygen partial pressures in the range 8 × 10⁻⁵–8 × 10⁻⁴ mbar and at a fixed substrate temperature of 473 K employing dc magnetron sputtering technique. The influence of oxygen partial pressure on the composition stoichiometry, chemical binding configuration, crystallographic structure and electrical and optical properties was systematically studied. X-ray photoelectron spectra of the films formed at 8 × 10⁻⁵ mbar showed the presence of Mo⁶⁺ and Mo⁵⁺ oxidation states of MoO₃ and MoO_3−x. The films deposited at oxygen partial pressure of 2 × 10⁻⁴ mbar showed Mo⁶⁺ oxidation state indicating the films were nearly stoichiometric. It was also confirmed by the Fourier transform infrared spectroscopic studies. X-ray diffraction studies revealed that the films formed at oxygen partial pressure of 2 × 10⁻⁴ mbar showed the presence of (0 k 0) reflections indicated the layered structure of α-phase MoO₃. The electrical conductivity of the films decreased from 3.6 × 10⁻⁵ to 1.6 × 10⁻⁶ Ω⁻¹ cm⁻¹, the optical band gap of the films increased from 2.93 to 3.26 eV and the refractive index increased from 2.02 to 2.13 with the increase of oxygen partial pressure from 8 × 10⁻⁵ to 8 × 10⁻⁴ mbar, respectively.