介质加载复合光栅结构的色散特性研究

提出了一种用于Smith-Purcell器件的介质加载金属光栅周期慢波结构.通过采用本征函数法和单模近似法求解了介质加载金属光栅的"热"色散方程,在同步点得到了注-波互作用的一阶和二阶增长率,分析了光栅槽宽和槽深对色散特性的影响,并研究了电子注参数及其与光栅表面距离等主要参数对增长率特性的影响.结果表明:通过介质加载金属光栅有利于减弱色散,随着介质相对介电常数、槽宽度以及深度的增大,色散曲线变平缓且向低频区移动;当电子注参数变化时,一阶增长率曲线从整体上粗略地描述增长率变化趋势,二阶曲线则更精细地描述增长率相应值的变化.利用软件MAGIC对该结构的色散特性进行了二维模拟,模拟结果与理论计算值符合良好.     

波纹内导体返波振荡器的热腔特性

 导出了波纹内导体同轴慢波结构热腔色散方程，研究了周期波纹深度、电子注平均半径、电子注电流及加速电压对波纹内导体慢波结构的高频场时间增长率的影响。结果表明：慢波结构周期减小、波纹深度加深、电子注平均半径减小、电子注电流增大、加速电压增大均会使高频场时间增长率增大。建立了粒子模型并应用PIC粒子模拟软件进行仿真，对各影响参数进行优化，结果表明：当加速电压为0.5 MV、电子束电流85 kA、波纹周期长度4.4 cm、波纹幅度为0.23 cm、内轴平均半径为2.9 mm和外壁内径为4.4 cm时，可获得10 GHz，1.1 GW效率约25%的单频微波输出。     

介质加载的矩形截面Cerenkov脉塞中带状电子注与慢波结构互作用的研究

本文建立了介质加载的矩形截面Cerenkov脉塞中带状电子注与慢波结构互作用的三维物理模型. 采用Borgnis函数法和场匹配法求解了多层介质中场的匹配问题, 获得了注波互作用结构的混合模热色散方程(含电子注)及其近似解. 通过数值计算, 分析了热态下介质层厚度、电子注电压、电流密度、电子注厚度及电子注与 介质层间隙距离等主要结构和电参数对注波互作用增长率的影响.     

相对论返波管注-波作用不稳定区的研究

 以环形电子注驱动的、正弦型周期慢波结构的相对论返波管（RBWO）为模型，理论推导出RBWO慢波结构的色散方程，画出了不包括和包括电子注的色散曲线，然后采用在复平面上绘制等高线图进行逼近的方法对注-波作用不稳定区工作频率的实部和虚部进行了求解，绘出了完整的包括电子注的慢波结构色散关系曲线，并估算了微波的时间增长率和能量转换效率。研究得出：当a（电子注电流参数）较大时，电磁波与慢电荷波的相互作用是不稳定的；而在a较小时，注-波相互作用具有明显的三波作用的特点；微波增长是通过注-波不稳定作用引起的；随着a的增大，微波时间增长率先增大后减小，在a为0.02时有最大值1.37，此时的能量转换效率为19%；增大电子注半径或慢波结构的波纹深度都可以增强注-波不稳定作用。     

填充等离子体的介质同轴波导中的切伦科夫辐射

 利用自洽线性场理论，导出了薄环形相对论电子注通过填充等离子体的介质同轴波导中的注波互作用色散方程，得到了注波互作用产生切伦科夫辐射的同步条件和波增长率。分析了填充等离子体后的波与电子注之间的能量交换及等离子体密度对色散特性、波增长率和注波能量交换的影响。分析结果表明：切伦科夫辐射是由沿介质同轴波导传播的慢波与沿薄环形相对论电子注传播的负能空间电荷波耦合所致，且其耦合强度与电子注的密度成正比；输出频率和波增长率随着填充等离子体密度的增大而提高；保持一定的输出频率，增大电子注的束流可得到高的微波输出功率。     

金属柱平板慢波系统高频特性研究

对于离散的金属柱结构构建的周期性平板慢波系统,本文利用3维FDTD方法结合HFSS仿真软件深入分析了该慢波系统的高频特性.研究了金属柱高度、周期长度对色散特性的影响,计算了耦合阻抗,并与传统光栅慢波系统特性进行了对比分析.分析表明金属柱慢波系统既有与传统光栅慢波系统相似的高频特性,又具有独自的特点,位于离散的金属柱周期间隙中的电子注互作用耦合阻抗具有对称性;金属柱结构用作真空电子器件的高频系统可增加发生有效互作用的电子注厚度,降低起振电流密度,提高器件效率.本文的分析结果为设计低电流密度工作的多电子注短毫 关键词： 金属柱平板慢波系统 3维FDTD算法 色散特性 耦合阻抗     

填充等离子体的介质契伦柯夫脉塞

 利用自洽线性场理论，普遍讨论了电子在扰动场作用下的三维扰动，进而分别对薄环形相对论电子注和实心相对论电子注在填充等离子体的介质筒慢波波导中激励的契伦柯夫辐射进行了详细的分析，导出了其色散方程和波增长率。分析表明注波互作用是由于慢波系统中的波导模与电子注模耦合所致，填充等离子体后能大大提高注波互作用效率，并详细计算和分析了等离子体密度和电子注半径对波增长率的影响。     

介质加载折叠波导行波管的线性分析

提出了一种介质加载折叠波导慢波结构,给出了该结构中存在电子注时慢波互作用的热色散方程,在介电常数ε_r=1的特殊情况下该方程即简化为普通折叠波导的小信号工作方程.在给定慢波结构尺寸的基础上,分析比较了介质加载对放大器小信号增益特性的影响,结果表明:"弱加载"(介质厚度d/a<0.1)时,无需重新设计慢波结构的参数,只需适当调整工作电压和电流就可以满足原有设计要求,而且和未加载时相比增益特性更为平坦,降低的电子注阻抗也有利于电子效率的提高.考虑到 关键词： 折叠波导 行波管放大器 介质加载 热色散方程     

基于史密斯-帕赛尔效应的太赫兹振荡器的原理与特性分析

提出了一种基于史密斯-帕赛尔效应的太赫兹振荡器,该器件由电子枪、调制腔、输出腔、收集极等部分构成。在器件调制腔中,电子注的速度调制通过史密斯-帕赛尔效应完成的,当群聚电子注通过输出腔时,群聚电子注会在输出腔的间隙处激励起高频电场,该高频电场会使电子注的一部分动能转换为高频能量,并完成太赫兹振荡.模拟发现:当金属光栅的空间周期为0.6mm、电子注能量为100keV时,利用史密斯-帕赛尔效应调制的太赫兹振荡器可以输出频率为349.017GHz和346.324GHz、功率谱密度接近4kW/GHz、最大输出峰值功率超过2kW的太赫兹波.     

含等离子体柱的介质慢波波导中的注波互作用分析

提出了一种新的注波互作用慢波系统——在部分填充介质的波导中放置一等离子体柱．利用线性自洽场理论，对这一新慢波系统中的相对论电子注与波的互作用进行了分析．具体针对薄环形相对论电子注包围等离子体柱和在等离子体柱内穿过慢波系统这两种情况，分别导出了决定注波互作用的色散方程．并对色散方程直接进行了数值求解，求得了系统的截止频率、工作频率和波增长率等．讨论了等离子体柱等有关参数对它们的影响． 关键词：     

Field theory of dielectric Cherenkov maser

The effect of three-dimensional perturbed velocity and three-dimensional perturbed current density on the beam-wave interaction of dielectric Cherenkov maser is analysed by use of the self-consistent linear field theory. Three distinct cases are considered. First, the propagation of the electron beam in an annular dielectric liner enclosed by a loss-free conducting wall is investigated. The dispersion equation and the simultaneous condition of the beam-wave interaction are derived. It's clearly shown that the instability of the interaction results from the coupling of the TM mode in the dielectric lined slow-wave waveguide to the beam mode via the electron beam. And the coupling is proportional to the density of the beam. The growth rate of the wave produced by the electron beam are obtained. Then, the case of a relativistic electron beam guided by a longitudinal magnetic field in the same slow-wave structure is examined. The motion of electrons could be approximated to be one-dimensional when the simultaneous condition of the beam-wave interaction of dielectric Cherenkov maser is satisfied. Finally, the effect of the background plasma on the instability of the beam-wave interaction is studied.This work is supported by National Natural Science Foundation of China.     

Linear Theory of Plasma-Filled Coaxial Cylindrical Cherenkov Maser

Injection of background plasma into the beam-wave interaction region can greatly enhance the beam-wave interaction efficiency and the microwave output power of the device. In this paper, a new type of plasma-filled slow-wave structure, i.e., plasma-filled, dielectric-loaded coaxial cylindrical waveguide with a dielectric ring enclosing tightly the inner conductor, is developed. The Cherenkov radiation excited by the beam-wave interaction in the slow-wave structure is examined by use of the self-consistent linear field theory. The dispersion equation and the synchronized condition of the beam-wave interaction are derived. It's clearly shown that the Cherenkov radiation excited by the beam-wave interaction results from the coupling between the slow electromagnetic wave, TM-modes, propagated along the slow-wave structure and the negative-energy space-charge wave propagated along the relativistic electron beam. And the wave growth rate is solved, and the beam-wave energy exchange in the presence of the background plasma is discussed. Finally, the effects of the background plasma density on the dispersion characteristics, the distribution of the longitudinal fluctuating electric field, the wave growth rate and the beam-wave energy exchange are calculated and discussed.     

速调型相对论返波管理论研究

对速调型相对论返波管慢波结构色散特性及束波相互作用进行了理论研究。色散特性研究表明:器件工作模式为TM01模,近点,耦合阻抗较高。色散特性预测的工作频率与粒子模拟结果非常接近。慢波结构峰值增长率相对较小,这与电子束与慢波结构相距较大有关,因而器件从起振到饱和的时间较长。在束波相互作用理论中,全面考虑了电子束与慢波结构前向波基波、反向波－1次空间谐波及空间电荷场相互作用、谐振反射器对电子束进行的束流调制和能量调制作用,以及调制腔和提取腔处引入的耦合阻抗及轴向波数突变。稳态和非稳态计算结果均获得了超过40%的束波转换效率。     

A millimeter wavelength radiation source using a dual gratingresonator

A novel means of producing coherent radiation by passing an electron through a dual-grating resonator is presented, The observed radiation is in accordance with the Smith-Purcell dispersion relation for a single grating. Feedback is provided by a second grating. Experiments carried out at beam energies from 30-55 keV produced radiation at wavelengths from 6 to 0.75 mm. Power measurement were used to clarify the grating beam interaction, Indications are that operation could be easily extended to shorter wavelengths to provide an inexpensive and compact radiation source in the far-infrared     

0.14 THz双环超材料慢波结构表面波振荡器数值研究

本文研究了一种太赫兹波段双环超材料慢波结构, 并具有同轴引出结构的相对论过模表面波振荡器. 设计了超材料同轴过模慢波结构; 通过色散特性, 进行了模式选择和过模结构电子束电参数和几何参数的设计; 根据超材料同轴慢波结构的特点, 设计了具有同轴引出结构的末端同轴输出段. 粒子模拟结果表明, 在电子束电压为600 kV和电流为1.0 kA, 引导磁场为2.0 T 时, 同轴超材料慢波结构过模表面波振荡器输出稳定单频的0.141 THz电磁波, 峰值功率为316.8 MW.     

DIELECTRIC EFFECT ON THE RADIO-FREQUENCY CHARACTERISTICS OF A RECTANGULAR WAVEGUIDE GRATING TRAVELING WAVE TUBE

A new type of partial-dielectric-loaded rectangular waveguide grating slow-wave structure (SWS) for millimeter wave traveling wave tube (TWT) is presented in this paper. The radio-frequency characteristics including the dispersion properties, the longitudinal electric field distribution and the beam-wave coupling impedance of this structure are analyzed. The results show that the dispersion of the rectangular waveguide grating circuit is weakened, the phase velocity is reduced and the position of the maximum E _z is basically invariant after partially filling the dielectric materials in the rectangular waveguide grating SWS. Although the coupling impedance decreases a little, it still keeps above 40 Ω.     

Design of Smith-Purcell emitter in femtosecond accelerator

Based on the femtosecond accelerator device, we are planning to build a broad band and tunable THz source using the Smith-Purcell radiation mechanism. Coherent Smith-Purcell radiation could be achieved owing to the super-short bunch produced in the device. To shorten the distance between the beam and grating, we use Transport to match the beta function producing a sheet beam on the grating surface. The optimization of grating length, groove depth and groove width are given in the paper. Then the radiation power for the shallow and deep grating using these parameters are presented. The detection devices and methods are also briefly discussed.     

Design of Smith-Purcell emitter in femtosecond accelerator

Based on the femtosecond accelerator device,we are planning to build a broad band and tunable THz source using the Smith-Purcell tadiation mechanism.Coherent Smith-Purcell radiation could be achieved owing to the super-short bunch produced in the device.To shorten the distance between the beam and grating,we use Transport to match the beta function producing a sheet beam on the grating surface.The optimization of grating length,groove depth and groove width are given in the paper.Then the radiation power for the shallow and deep grating using these parameters are presented.The detection devices and methods are also briefly discussed.