真空弧放电TiH合金阴极表面形貌分析

TiH合金电极是一种含氢量非常高的金属材料,用它作真空弧离子源的电极,可在真空环境下产生强度非常高的氢离子流。相比纯金属材料电极,TiH电极除了出现真空弧放电特有的融蚀现象外,还存在气体释放过程,所以它的表面形貌具有一定的独特性。利用扫描电子显微镜观察了单次放电和多次放电后阴极表面形貌,发现阴极斑在阴极表面微裂纹附近连续分布,气体释放生成很多小孔,使阴极斑区域呈絮状结构;弧流越大,阴极斑数量越多;多次放电后,阴极斑朝含氢量多的地方移动。该结果有助于了解含氢电极的真空弧放电过程,对该类放电的应用具有一定参考意义。     

含氘电极真空弧等离子体空间分布特性诊断研究

真空弧放电等离子体含有多种离子成分,并且各离子在空间上具有不同的分布规律.本文针对金属氘化物电极真空弧离子源,搭建了一台紧凑型磁分析装置,用来研究放电等离子体中氘离子与金属离子的空间分布.当离子源弧流为100 A左右时,该装置能有效地传输引出束流,并且具有较好的二次电子抑制效果,可准确获得各离子流强.利用该装置测量并获得了氘化钛含氘电极真空弧放电等离子体内氘离子和钛离子空间分布规律,结果表明:径向上,氘离子和钛离子都呈高斯分布,但氘离子分布均匀,而钛离子相对集中在轴线附近,导致轴线附近氘离子比例最低;轴向上,所有离子数量都以自然指数函数减少,而且相对幅度接近,所以氘离子比例几乎不变.本文研究结果不仅有助于理解真空弧放电等离子体膨胀过程,还可以指导金属氘化物电极真空弧离子源及其引出设计.     

用于真空弧等离子体放电阴极温度场测量的多光谱高温计

阴极表面温度是真空弧等离子体放电过程中一个重要参数,对真空弧等离子体的形成、电极腐蚀预测、热传导以及离子源的寿命都有重要影响。真空弧离子源的阴极具有目标小,放电过程快等特点,其温度的测量,对于时间分辨率和空间分辨率要求都很高,阴极表面温度的测量技术的欠缺,使得仅靠理论解析获得的结果难以得到验证。并且等离子体放电过程中测量仪器极易受到弧光的影响,如何避免放电过程中等离子体的辐射也是采用辐射法测量阴极表面温度要考虑的问题。这无疑给其温度场的测试研究带来困难。针对脉冲真空弧等离子体开展阴极表面温度测试实验有着重要意义,在分析了真空弧等离子体放电特性以及背景辐射特性和等离子体放电阴极测温的实际需求,本文基于高速CCD相机研制了一种新型的多光谱高温计。该高温计采用单色高速CCD相机,主要避免RGB彩色相机不能完全滤除背景辐射的弧光。为使用单色CCD相机实现多光谱辐射测温,设计了高温计的光学系统,该系统采用4孔径分光系统。将4种不同波长的滤光片嵌入到1个滤光片中。该研究设计的高温计可用于2 000~6 000 K的等离子体温度测量。并在中国工程物理研究院电子工程研究所进行现场测试,测试过程中将研制的高温计,通过外部触发形式对等离子体放电过程进行跟踪拍摄,高温计完全拍摄到等离子体放电过程。利用真空弧等离子体金属电极阴极放电的实测数据对高温计进行了验证。实验结果表明,设计的新型多光谱高温计能够用于测量真空弧等离子体放电时阴极温度场信息,测量的温度值低于放电电极的沸点温度,与等离子体放电过程中出现气化现象相符,说明高温计测的是等离子体放电阴极的温度。     

基于Mie散射在线测量真空弧放电液滴方法探索

金属液滴是真空弧放电的伴随产物,它对理解阴极斑放电性质具有重要作用,而且对工程应用也有重要影响.金属液滴的测量一般采用离线的收集法,不能获得全部空间和单次放电信息.本文提出了一种通过Mie散射在线测量真空弧放电液滴的新方法,并对它的可行性进行了探索研究.首先通过仿真程序计算了钛金属液滴的散射光性质,结果表明小直径颗粒散射光在全部角度上均有分布,随着直径增加,散射光越来越集中在前向,这为不同直径液滴信号的反演提供了可能.接着对探测器进行了分环设计,当探测器分为35环时,光能系数矩阵容易求解,同时保证测量系统具有良好的分辨率.初步实验结果表明,钛金属液滴直径主要分布在9.8 μm附近,验证了Mie散射测量真空弧液滴方法的有效性.但液滴直径分布和离线测量有较大差异,缺少小直径液滴信息,主要原因来源于测量系统信噪比不够,不能有效地获得小直径液滴散射信号,还需要进一步优化.     

MEVVA放电在材料表面改性上的应用

本文描述了金属蒸发真空弧放电的特点，阴极弧等离子体的形成过程，以及在加热蒸发电离方式相比ＭＥＶＶＡ放电的优越性。文章还叙述了建筑的ＭＥＶＶＡ离子源的实用参数，工作过程及ＭＥＶＶＡ等离子体源在全方位离子注入装置中的应用。     

含氢电极真空弧放电等离子体时空分布特性研究

真空弧离子源在真空镀膜、材料表面改性、真空大电流开关、加速器离子注入等领域有广泛应用,目前国内外对真空弧放电等离子体的研究主要针对纯金属或合金电极,对含氢电极的研究和公开报道较少.本文利用高时空分辨的四分幅图像诊断系统,结合氢和钛原子特征线单色器件,研究了含氢钛电极的真空弧微秒级脉冲放电等离子体的轴向和径向时空分布特性.研究表明:在真空击穿阶段,阳极区域发光更为明显,阳极电极解吸附释放的氢原子是引发击穿的主要放电介质;在真空弧阶段,阴极-绝缘-真空三结合点处产生圆锥状阴极斑,喷射出大量的等离子体以维持弧放电,同时电极内壁非阴极斑区域也有少量等离子体产生,等离子体中H原子的轴向和径向空间分布均比Ti原子均匀.     

高电流低气压等离子体阴极电子枪设计与实验

 设计了一种新型的高功率低气压等离子体电子枪。基于空心阴极效应和低压辉光放电原理与经验，确定了空心阴极、加速间隙、工作气压范围等。提出关于等离子体阴极电子枪产生高功率、高密度电子束源的整体方案。分别在连续馈气和脉冲馈气条件下进行实验测试，得到放电电流、收集极电流与气压、脉宽及调制器电压的关系。实验获得电子枪的典型放电电流为150~200 A，脉宽60 μs；传输电子束达到30~80 A，脉宽60 μs。该结果表明该新型等离子体阴极电子枪可以取代材料阴极作为大电流、长脉冲电子束源，特别适用于等离子体加载微波管。     

N2���������ŵ���΢���������ŵ�ת���PIC/MCģ��

开发了氮空心阴极放电PIC/MC二维自洽模型。研究了N2传统空心阴极向微空心阴极放电转变过程中电势和电场的变化。结果表明,不同尺寸的空心阴极放电的电势及电场分布规律几乎类似,但空心阴极孔径减小且气压增加时,电场近似线性增加;典型微空心阴极电场比传统空心阴极放电电场约大3个量级;微空心阴极放电产生的电子,氮分子离子和氮原子离子的密度比传统空心阴极放电约大3个量级,且微空心阴极放电中,N2+密度比N+密度大8倍以上。     

微空心阴极放电的流体模型模拟

采用流体模型研究了微空心阴极放电(MHCD)的特点，对放电中电场的形成，电子和离子的密度分布，电子能量分布进行了数值模拟.该计算是针对高气压，圆筒形阴极结构下的He放电.结果表明放电中存在空心阴极效应，从电子能量分布可以看出，放电中存在高能电子，放电空间的电场分布主要表现为径向电场.此外，通过改变气压，阴极孔径等参数计算出它们对放电的影响.分析表明减小孔径有利于负辉区更充分的重合.提高气压将缩短阴极位降区. 关键词： 微空心阴极放电 流体模型     

微空心阴极维持放电的实验研究

为在高气压下形成大体积均匀等离子体,将微空心阴极放电(MHCD)作为等离子体阴极,引入另一阳极而设计为微空心阴极维持放电(MCSD)的发生装置.实验研究了MCSD的产生放电条件,通过在氩气中添加少量氮气,分析氮分子第一正带系发射光谱的方法测量了MCSD中羽流区不同位置的气体温度.研究表明,当等离子体阴极电流增加到一个临...     

Effect of the discharge parameters on the generation of deuterium ions in the plasma of a high-current pulsed vacuum arc with a composite zirconium deuteride cathode

We have studied the mass and charge composition of an ion beam extracted from the plasma of a vacuum arc with a zirconium deuteride cathode for various durations of the arc current pulse (half width at half amplitude) of 2, 4, 7, and 17 μs. It has been established that the fraction of deuterium ions in the vacuum arc plasma increases with the current and the dependence achieve saturation for current of about 1 kA. For the fraction of deuterium atoms in the cathode at a level of 40%, the fraction of deuterium ions in the vacuum arc plasma can exceed 80%. The experimental results have been interpreted theoretically. It has been shown that the main sources of deuterium ions in a microsecond arc discharge are cathode spots. We have developed a model of deuterium desorption during the operation of cathode spots for quantitatively estimating the concentration of deuterium ions in the arc plasma.     

Displacement of Field Emitters by Vacuum Discharges

The location of field emitting micro-points, produced by nanosecond discharges in UHV, has been investigated by field emission microscopy. Weak discharges (duration < 5 ns, current < 10 A) caused a displacement of the field emission over the cathode by a distance that corresponds to average crater diameters (4–6 μm). Thus new emitters are produced at the boundary of discharge craters. More intense discharges show sometimes a far higher displacement. This can be explained by the formation of micro-points by splashes of molten metal that fly out of the discharge craters. The results support the model of the development of micro-points, as it was published in [1]. They show furthermore that the motion of arc cathode spots can be related to the displacement of microscopic field emitters.     

From Field Emission to Vacuum Arc Ignition: A New Tool for Simulating Copper Vacuum Arcs

Understanding plasma initiation in vacuum arc discharges can help to bridge the gap between nano‐scale triggering phenomena and the macroscopic surface damage caused by vacuum arcs. We present a new twodimensional particle‐in‐cell tool to simulate plasma initiation in direct‐current (DC) copper vacuum arc discharges starting from a single, strong field emitter at the cathode. Our simulations describe in detail how a sub‐micron field emission site can evolve to a macroscopic vacuum arc discharge, and provide a possible explanation for why and how cathode spots can spread on the cathode surface. Furthermore, the model provides us with a prediction for the current and voltage characteristics, as well as for properties of the plasma like densities, fluxes and electric potentials in a simple DC discharge case, which are in agreement with the known experimental values. (© 2015 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Microscopic high speed investigations of vacuum arc cathode spots

The main parameters and dimensions of cathode spots have been under discussion for years. To solve these current questions, a new system was specially designed. The image converting high speed framing camera (HSFC) combines a micrometer lateral resolution with a nanosecond time resolution and a very high optical sensitivity. This camera was used to study the microscopic behavior of vacuum arc cathode spots in a pulsed high current arc discharge on copper. The direct observation of these spots with high resolution revealed that one single cathode spot, as normally observed by optical means, consists of a number of simultaneously existing microscopic subspots, each with a diameter of about 10 μm and a mean distance of 30-50 μm between them. The mean existence time of these subspots on copper was found to be about 3 μs, where the position of a subspot remains unchanged (with an upper limit of about 5 μm) during its existence time. The lower limit of the current density in the cathode spots was estimated to be on the order of 10¹⁰-10¹¹ A/m². An upper limit of the crater surface temperature was estimated by a comparison between the brightnesses of a cathode spot and of a black body radiation lamp to about 3000 K     

Investigation of the Directional Velocities of Ions in a Vacuum Arc Discharge by Emission Methods

This paper is devoted to an investigation of the directional velocities of the ions generated in cathode spots of vacuum arc discharges. By using emission methods of studying the processes in a vacuum arc discharge, which involve the determination of the parameters and characteristics of the discharge plasma by analyzing the ion current extracted from the plasma and the ion charge states, the velocities of ions have been determined for the majority of cathode materials available in the periodic table. Is has been shown that at a low pressure of the residual gas in the discharge gap the directional velocities of the ions do not depend on the ion charge state. Comparison of the data obtained with calculated values allows the conclusion that the acceleration of ions in a vacuum arc occurs by the magnetohydrodynamic mechanism.     

Gyrocenter shift of low-temperature plasmas and the retrograde motion of cathode spots in arc discharges

The gyrocenter shift phenomenon explained the mechanism of radial electric field formation at the high confinement mode transition in fusion devices. This Letter reports that the theory of gyrocenter shift is also applicable to low temperature high collisional plasmas such as arc discharges by the generalization of the theory resulting from a short mean free path compared with the gyroradius. The retrograde motion of cathode spots in the arc discharge is investigated through a model with the expanded formula of gyrocenter shift. It is found that a reversed electric field is formed in front of the cathode spots when they are under a magnetic field, and this reversed electric field generates a rotation of cathode spots opposite to the Amperian direction. The ion drift velocity profiles calculated from the model are in agreement with the experimental results as functions of magnetic flux density and gas pressure.     

A Review of Anode Phenomena in Vacuum Arcs

This paper discusses arc modes at the anode, anode temperature measurments, anode ions, transitions of the arc into various modes (principally the anode-spot mode), and theoretical explanations of anode phenomena. A vacuum arc can exhibit five anode discharge modes: 1) a low-current mode in which the anode is basically passive, acting only as a collector of particles emitted from the cathode; 2) a second low-current mode that can occur if the electrode material is readily sputtered (a flux of sputtered atoms will be emitted by the anode); 3) a footpoint mode, characterized by the appearance of one or more luminous spots on the anode (footpoints are much cooler than the true anode spots present in the last two modes); 4) an anode-spot mode in which one large or several small anode spots are present (such spots are very luminous, have a temperature near the atmospheric boiling point of the anode material, and are a copious source of vapor and ions); and 5) an intense-arc mode where an anode spot is present, but accompanied by severe cathode erosion. The arc voltage is relatively low and quiet in the two low-current modes and the intense-arc mode. It is usually high and noisy in the footpoint mode, and it can be either in the anode-spot mode. Anode erosion is low, indeed negative, in the two low-current modes, and it is low to moderate in the footpoint mode. Severe anode erosion occurs in both the anode-spot and intense-arc modes.     

Current Density Per Cathode Spot in Vacuum Arcs

Two methods of computing the current density in a cathode spot of a metal arc are compared. The first method computes the spot area in terms of a crater left on the metal. Detailed arguments are presented as to why this method is not correct. Evidence is presented supporting a second method, that of estimating the cathode spot from the luminous glow observed during the discharge. The current density is estimated to be less than 105 A/cm2 during the lifetime of the spot.     

Triggered discharges with high arc voltages in a vacuum interrupter

Studies of nonsustained disruptive discharges (NSDDs), isolated cases of which can occur in vacuum interrupters, indicate lateral discharges between the cathode and shield, which can initiate a brief discharge between the contacts. To facilitate the study of such discharges, the sample discharges were triggered by a surface discharge induced by a spark gap, built into the side of the cathode, and observed with a high-speed film camera and image-converter camera. The tests showed a cathode spot after igniting. The emitted electrons first charge the shield negatively and then are directed toward the anode. The discharge burns at a high voltage, with current ranging from 10 to 100 A. After a period of up to 400 μs, the current demand increases abruptly; an arc discharge occurs between the contacts and discharges the capacitances near the switch. The contact gap undergoes a rapid dielectric recovery, and the restored voltage is maintained. These types of discharge were also observed with NSDDs; thus it can be assumed that the triggered discharges studied correspond to the NSDD type