Characterization of Y<Subscript>2</Subscript>BaCuO<Subscript>5</Subscript> nanoparticles synthesized by nano-emulsion method

Nanoscale yttrium–barium–copper oxide (Y₂BaCuO₅, Y211) particles were synthesized using the emulsion method and the solution method. The basic water-in-oil (w/o) emulsion system consisted of n-octane (continuous oil phase), cetyltrimethylammonium bromide (cationic surfactant), butanol (cosurfactant) and water. The composition of the emulsion system was varied and characterized by measuring the conductivity of the solutions and droplet size. The droplet size of emulsion was determined by using the dynamic light scattering method. The water content, cosurfactant content, and surfactant/n-octane ratio affected the droplet size which was in the range of 3–8 nm, and hence the w/o emulsion system was referred to as a nano-emulsion system. A model was used to verify the droplet size. The influence of salt (Y₂(NO₃)₃) content on the droplet size was investigated and the addition of salt reduced the droplet size. The effects of reaction time and temperature on the Y211 particle sizes were also investigated. The particles were characterized using the TEM, SEM, and XRD. Nanoparticles produced by the nano-emulsion method were calcined at 850°C to form the Y211 phase as compared to solid state processing temperature of 1050°C. Based on the TEM analysis, the average diameter of the Y211 particles produced using the nano-emulsion method was in the range of 30–100 nm. The effect of adding 15% Y211 nanoparticles to the superconductor YBCO-123 as flux pinning centers, was investigated, and the transition temperature was reduced by 3 K.     

Structural investigation of viscoelastic micellar water/CTAB/NaNO<Subscript>3</Subscript> solutions

A highly viscoelastic worm-like micellar solution is formed in hexadecyltrimethylammonium bromide (CTAB) in the presence of sodium nitrate (NaNO₃). A gradual increase in micellar length with increasing NaNO₃ was assumed from the rheological measurements where the zero-shear viscosity (η ₀) versus NaNO₃ concentration curve exhibits a maximum. However, upon increase in temperature, the viscosity decreases. Changes in the structural parameters of the micelles with addition of NaNO₃ were inferred from small angle neutron scattering measurements (SANS). The intensity of scattered neutrons in the low q region was found to increase with increasing NaNO₃ concentration. This suggests an increase in the size of the micelles and/or decrease of intermicellar interaction with increasing salt concentration. Analysis of the SANS data using prolate ellipsoidal structure and Yukawa form of interaction potential between micelles indicate that addition of NaNO₃ leads to a decrease in the surface charge of the ellipsoidal micelles which induces micellar growth. Cryo-TEM measurements support the presence of thread-like micelles in CTAB and NaNO₃.      

Effect of hydrophobicity of cationic carbocyanine dyes DiOC<Subscript><Emphasis Type="Italic">n</Emphasis></Subscript> on their binding to anionic surfactant micelles

The interaction of a series of cationic dialkyloxacarbocyanine perchlorate (DiOC _n ) dyes of different degrees of hydrophobicity with micelles of an anionic surfactant, sodium dodecylsulfate (SDS), has been studied spectrophotometrically in aqueous solutions. The Benesi–Hildebrand equation was used to calculate binding constants (K _b ) of the dyes to surfactant micelles, the fraction of dye bound to the micelles (f _mic ), and the standard free-energy change (ΔG ⁰) for the transfer of dye from the aqueous to micellar phase. It has been shown that the interaction of oppositely charged dye molecules and surfactant micelles is controlled by both electrostatic and hydrophobic interactions. A small increase in dye hydrophobicity due to lengthening of the hydrocarbon radical has been shown to cause an abrupt nonlinear increase of the fmic value. This points to a key role of hydrophobic interactions in the binding of dye molecules with the micelles.     

The influence of the structural characteristics of the substrate and the medium on the stability of triflusal and acetylsalicylic acid in micellar systems

A spectrophotometric study of the alkaline hydrolysis of two salicylic acid (SA) derived drugs, performed on acetylsalicylic acid (ASA) and triflusal, both in the absence and presence of cationic micelles. In the absence of micelles, a catalytic effect is produced by the favoured OH⁻ ion in the molecule of triflusal, due to the presence of the trifluoromethyl group. The surfactants used were: hexadecyltrimethylammonium hydroxide (HDTAOH), hexadecyltrimethylammonium chloride (HDTACl), hexadecyltrimethylammonium bromide (HDTABr), hexadecylethyldimethylammonium bromide (HDEDABr) and tetradecyltrimethylammonium bromide (TDTABr). In micelles with reactive counterions, the pseudo-first-order rate constant (k_obs) increases with the increase in surfactant concentration, while in micelles with non-reactive counterions, the rate constant increased with surfactant concentration at low concentration, reaching a maximum, and decreased at high surfactant concentration, even to below the value found in the absence of micelle. The micellar binding constant of both drugs (K_S), the micellar rate constant (k_M) and the ion-exchange constant (K_X^OH) were determined according to variation in k_obs in relation to surfactant concentration, through the application of the pseudophase ion-exchange model (PPIE) proposed. The empirical parameters obtained were found to depend on the substrate and the surfactant structure, these parameters were: the counterion of the micelle, the size of the headgroup and the chain length of the hydrophobic tail of the surfactant.     

Influence of solvents on the morphological properties of AgBr nano-structures prepared using ultrasound irradiation

Nano-structures of AgBr have been prepared by reaction between AgNO₃ and KBr under ultrasound irradiation. Particle sizes and morphology of nanoparticle are depending on temperature, power of sonicating, reaction time and concentration. The effects of these parameters in growth and morphology of the nano-structures have been studied. Results suggest that an increasing of temperature, sonication power and concentration led to a decreasing of particle size. The samples were characterized with powder X-ray diffraction (XRD) and scanning electron microscopy (SEM).     

Green synthesis of silver nanoparticle by <Emphasis Type="Italic">Penicillium purpurogenum</Emphasis> NPMF: the process and optimization

An eco-friendly microbial method for synthesis of silver colloid solution with antimicrobial activity is developed using a fungal strain of Penicillium purpurogenum NPMF. It is observed that increase in concentration of AgNO₃ increases the formation of silver nanoparticle. At 5 mM concentration highly populated polydispersed nanoparticles form. Furthermore, change in pH of the reaction mixture leads to change in shape and size of silver nanoparticles. At lower pH two peaks are observed in the absorption spectra showing polydispersity of nanoparticles. However, highly monodispersed spherical nanoparticles of 8–10 nm size form with 1 mM AgNO₃ concentration at pH 8. Antimicrobial activity of nanoparticles is demonstrated against pathogenic gram negative bacteria like Escherichia coli and Pseudomonas aeruginosa, and gram positive bacteria like Staphylococcus aureus. The antimicrobial activity of silver nanoparticles obtained at different initial pH show strong dependence on the surface area and shape of the nanoparticles.     

Effects of solubilized dodecylamine on the microstructure of cetylpyridinium bromide-<Emphasis Type="Italic">n</Emphasis>-butanol-hexane-water system studied by pulsed-gradient spin echo NMR and ESR spin label methods

The effect of solubilized dodecylamine (DDA) on the structure of the cetylpyridinium bromide-n-butanol-hexane-water microemulsions has been studied by the Fourier-transform pulsed-gradient spin-echo¹H nuclear magnetic resonance and the electron spin resonance spin label method. The sample compositions were chosen to examine three different microemulsion structures: oil-in-water, water-in-oil and bicontinuous. In all systems the DDA molecules are shown to be incorporated into the oil-water interface, resulting in essential changes in the microemulsion structure. In the micellar systems the DDA emergence in the interface causes an increase of the micelle size and a redistribution of butanol and water between micelle and bulk phases. In the oil-in-water microemulsions of amine-containing systems the quantity of micellized butanol and water decreases. In the water-in-oil microemulsions the introduction of DDA leads to an increase of butanol and water involved in the micelle formation. The redistribution of butanol and water between polar and organic phases in the microemulsions would be expected to cause changes in the bicontinuous structure.     

One-step synthesis of colloidal Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> and γ-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles at room temperature

A facile room-temperature synthesis has been developed to prepare colloidal Mn₃O₄ and γ-Fe₂O₃ nanoparticles (5 to 25 nm) by an ultrasonic-assisted method in the absence of any additional nucleation and surfactant. The morphology of the as-prepared samples was observed by transmission electron microscopy. High-resolution transmission electron microscopy observations revealed that the as-synthesized nanoparticles were single crystals. The magnetic properties of the samples were investigated with a superconducting quantum interference device magnetometer. The possible formation process has been proposed.     

Monitoring the Phase Transition of C12E5/Water/Alkane Microemulsions Through Excimer Formation

The phase transition of microemulsions involving the nonionic surfactant C₁₂E₅ [C₁₂H₂₅(OCH₂-CH₂)₅OH], water, and alkanes (heptane, decane and tetradecane) has been investigated through the excimer formation of pyrene. On going to the microemulsion bicontinuous phase, by changing either composition or temperature, pronounced changes in the pyrene excimer-to-monomer fluorescence intensity ratio, I _E/I _M, are observed. Several differences in the steady-state emission spectra and in fluorescence decay curves show that as a probe pyrene is well suited to follow the transition from the water continuous to the oil continuous phase, through an intermediate bicontinuous (continuous in both water and oil) region. The results provide information about the different characteristics and structure of these three regions (water continuous, bicontinuous, and oil continuous) of the phase diagram for C₁₂E₅/water/alkane systems.     

Poly(ethylene glycol) and phospholipid packing in the structure of reverse micelles

The influence of water substitution by a substance with a different polarity on the structure of phospholipid monolayer interface in water-in-oil microemulsion has been studied by the Fourier-transform pulsed-gradient spin-echo (FT PGSE)¹H nuclear magnetic resonance (NMR) and electron spin resonance (ESR) spin-label methods. For this purpose the soybean phosphatidylcholine-based microemulsion and water soluble poly(ethylene glycol) with molecular weight 400 (PEG400) were used. Self-diffusion coefficients of all microemulsion components obtained by the FT PGSE NMR technique provided information about both the size of reverse micelles and distribution of components between different microemulsion compartments. The maximum hyperfine splitting, 2A _max, in the ESR spectra was used to characterize the degree of the phospholipid hydrocarbon chain mobility. It was shown that PEG400 alters significantly the size of the reverse micelles and the motion of the labeled segments of the lipid tails. A mechanism of PEG400 acting in solution of the phospholipid-based reverse micelles on the basis of the rough decrease of the micelle core polarity was suggested.     

Hydrodynamic effects in bicontinuous microemulsions measured by inelastic neutron scattering

The dynamical properties of bicontinuous microemulsions have been studied with neutron spin echo spectroscopy around length scales corresponding to the correlation peak q₀. Comparison of samples with different contrasts for neutrons shed light on the two modes dominated either by variation of the oil/water difference or surfactant concentration in the hydrodynamic regime. The results have been compared to theoretical predictions of the relaxation rates of bicontinuous microemulsions by Nonomura and Ohta [M. Nonomura, T. Ohta, J. Chem. Phys. 110, 7516 (1999)]. The influence of modification of the surfactant layer bending constants in the microemulsion by addition of homopolymers (polyethylenepropylene: PEP_X and polyethyleneoxide: PEO_X, X=5 kg/mol), dissolved in the oil phase and water, has been investigated.     

Memory effects in superparamagnetic La<Subscript>0.6</Subscript>Pb<Subscript>0.4</Subscript>MnO<Subscript>3</Subscript> nanoparticles

Using different temperature and field protocols, the memory behaviors in the dc magnetization and magnetic relaxation are observed at temperature below blocking temperature T_B = 93 K in weakly interacting manganite La_0.6Pb_0.4MnO₃ nanoparticles. The results indicate that the magnetic dynamics of this nanoparticle system is strongly correlated with a wide distribution of particle relaxation times, which may arise from the particle weak interaction and distribution of the particle size.     

Percolation phenomenon of calcium bis(2-ethylhexyl) sulfosuccinate water-in-oil microemulsions by conductivity and dielectric spectroscopy measurements

The sodium counterion (Na+) of the sodium bis(2-ethylhexyl) sulfosuccinate (AOT) surfactant was exchanged with calcium Ca2+ to investigate the counterion charge effect on the structure of water in normal decane microemulsions. Ohmic conductivity and dielectric permittivity measurements were performed on samples at constant water to surfactant mole ratio [water]/[Ca(AOT)(2)]=26.6. Increasing the volume fraction of the dispersed phase phi, a percolation phenomenon was observed at the constant temperature of 25 degrees C. The percolation threshold was found at phi approximately 15% by Ohmic conductivity and static dielectric permittivity studied as a function of phi, and by the frequency dependence of the complex permittivity. Critical exponents typical of the static percolation mechanism (formation of bicontinuous microemulsions) were found below and above threshold. The comparison of these results obtained for the two different counterions, Ca2+ and Na+, in AOT surfactant water in normal decane microemulsions allows detection of an important difference. The percolation below threshold is dynamic for the sodium-based microemulsions, accounting for the formation of clusters of droplets, whereas calcium-based microemulsions show a static percolation. For this system, the coalescence of droplets begins to occur below threshold at phi approximately 12%.     

A study of the properties of mixed nonionic surfactants microemulsions by NMR, SAXS, viscosity and conductivity

The pseudoternary phase behavior of the water/sucrose laurate/ethoxylated mono-di-glyceride/R (+)-limonene systems was investigated for different surfactants mixing ratios (w/w) at 25 °C. The microemulsion boundaries were determined and the surfactants content at the interface of water- R (+)-limonene was estimated. For surfactants mixing ratio (w/w) equals unity, the area of the one phase microemulsion region reaches its maximum. The system with the maximum microemulsion area was investigated using electrical conductivity, dynamic viscosity, small angle X-ray scattering, and nuclear magnetic resonance. Electrical conductivity increases as the water volume fraction increases and a percolation threshold was observed. Dynamic Viscosity varies as function of the water volume fraction in a non-monotonic way giving two-peaked plot. The characteristics of the domain size of the microemulsions called periodicity measured by small angle X-ray scattering increases with the increase in the water volume fraction. The correlation length of the domain size reaches a maximum when plotted against the water volume fraction in the microemulsions. Relative diffusion coefficients of water increase and those of oil decrease with increasing the water volume fractions in the microemulsions indicating structural transitions.     

Self-assembly of rutile (α-TiO<Subscript>2</Subscript>) nanoclusters into nanorods in microemulsions at low temperature and their photocatalytic performance

A novel method – inverse microemulsion has been developed not only for synthesizing low cost TiO₂ nanocrystals but also for the first time making these nanocrystals self-assemble into various nanoparticles at 85°C. By variation of the volume ratios of oil to water in reverse microemulsions, the morphologies of obtained samples turned from nanoclusters to nanospherules, then grew into nanodumbbells, and became nanorods at last. It could be observed by transmission electron microscope (TEM) directly. The resulting materials were characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FESEM) and high-resolution transmission electron microscope (HRTEM). The photocatalytic activity of TiO₂ was tested with photodegradation of Methyl Orange (MO) in water. The catalyst consisting of nanorods showed the highest photocatalytic activity, which is due to its large surface area. Furthermore, the mechanism of self-assembly of TiO₂ nanocrystals was discussed in detail.     

The effective reinforcement of magnesium alloy ZK60A using Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles

ZK60A nanocomposite containing Al₂O₃ nanoparticle reinforcement (50 nm average size) was fabricated using solidification processing followed by hot extrusion. The nanocomposite exhibited similar grain size to the monolithic alloy, reasonable Al₂O₃ nanoparticle distribution, non-dominant (0 0 0 2) texture in the longitudinal direction, and 15% higher hardness than the monolithic alloy. Compared to the monolithic alloy (in tension), the nanocomposite exhibited lower yield strength (0.2%TYS) (−4%) and higher ultimate strength (UTS), failure strain, and work of fracture (WOF) (+13%, +170%, and +200%, respectively). Compared to the monolithic alloy (in compression), the nanocomposite exhibited lower yield strength (0.2%CYS) (−5%) and higher ultimate strength (UCS), failure strain, and WOF (+6%, +41%, and +43%, respectively). The effects of Al₂O₃ nanoparticle addition on the enhancement of tensile and compressive properties of ZK60A are investigated in this article.     

Kinetics and mechanisms of the UV-radiation-assisted formation of gold nanoparticles in HAuCl<Subscript>4</Subscript>-doped chitosan solutions

Using methods of optical spectroscopy and small-angle X-ray scattering, the kinetics of the UV radiation-induced formation of gold nanoparticles in HAuCl₄-doped water–acid solutions of chitosan has been studied from the very beginning of the reaction. It has been shown that, during synthesis, as the mean size of nanoparticles grows from 2.9 to 6.3 nm, the maximum of the plasmon resonance shifts toward shorter waves (535–523 nm), whereas for a fully formed ensemble of nanoparticles, the reverse trend is observed. It has been found experimentally that the particle size distribution curve changes during synthesis. Based on the inverse problem analysis, conclusions have been drawn regarding the dominant mechanisms behind nanoparticle growth.     

Structural and optical properties of novel surfactant-coated Yb@TiO<Subscript>2</Subscript> nanoparticles

In this paper a novel hybrid approach to synthesise composite nanoparticles is presented. It is based on the laser ablation of a bulk target (Yb) immersed in a reversed micellar solution which contains nanoparticles of a different host material (TiO₂ nanoparticles) previously synthesised by chemical method. This approach thus exploits the advantages of the chemical synthesis through reversed micellar solution (size control, nanoparticle stabilisation), and of the laser ablation (“clean” synthesis, no side reactions). Central role is played by the microscopic processes controlling the deposition of the ablated Yb atoms onto the surface of TiO₂ nanoparticles which actually behave as nucleation seeds. The structural features of the resulting Yb@TiO₂ composite nanoparticles have been studied by Transmission Electron Microscopy, whereas their peculiar optical properties have been explored by UV–Vis spectroscopy and steady-state fluorescence. Results consistently show the formation of Yb and TiO₂ glued nanodomains to form nearly spherical and non-interacting nanoparticles with enhanced photophysical properties.     

Peroxide-based route assisted with inverse microemulsion process to well-dispersed Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> nanocrystals

Well-dispersed bismuth titanate (BIT) nanocrystals with an average size ranged from 3 to 60 nm were synthesized via a peroxide-based route assisted with an inverse microemulsion process. The crystallite size and lattice parameter of BIT upon variable-temperature were determined by X-ray diffraction (XRD). The particle size was confirmed by transmission electron microscopy (TEM). Thermal decomposition behaviour of Ti-peroxy and BIT gel and crystallization kinetics of BIT nanocrystals were investigated by differential scanning calorimetry/thermogravimetry (DSC/TG) and Fourier-Transform infrared spectroscopy (FTIR). Analysis of nonisothermal DSC data yielded a value of 220.84 ± 2.73 KJ/mol and 2.25 ± 0.26 for the activation energy of crystallization (E _a) and the Avrami exponent (n), respectively.     

Synthesis and photoluminescent properties of silica-coated LaCeF<Subscript>3</Subscript>:Tb nanocrystals

La_0.45Ce_0.45F₃:Tb (10 mol% Tb) nanoparticles was synthesized via sonochemical method and then coated with silica (SiO₂) shells through a microemulsion process, resulting in the formation of core/shell structured LaCeF₃:Tb/SiO₂ nanoparticles. The obtained core/shell LaCeF₃:Tb/SiO₂ nanoparticles are spherical and uniform in size (average size about 60 nm), strongly fluorescent, and long fluorescence lifetime (1.87 ms). This kind of nanoparticles was water-soluble, which could be applied in biological labeling and other fields.