Laser-induced incandescence for soot particle size and volume fraction measurements using on-line extinction calibration

A novel technique for two-dimensional measurements of soot volume fraction and particle size has been developed. It is based on a combined measurement of extinction and laser-induced incandescence using Nd:YAG laser wavelengths of 532 nm and 1064 nm. A low-energy laser pulse at 532 nm was used for extinction measurements and was followed by a more intense pulse at 1064 nm, delayed by 15 ns, for LII measurements. The 532-nm beam was split into a signal beam passing the flame and a reference beam, both of which were directed to a dye cell. The resulting fluorescence signals, from which the extinction was deduced, together with the LII signal, were registered on a single CCD detector. Thus the two-dimensional LII image could be converted to a soot volume fraction map through a calibration procedure during the same laser shot. The soot particle sizes were evaluated from the ratio of the temporal LII signals at two gate time positions. The uncertainty in the particle sizing arose mainly from the low signal for small particles at long gate times and the uncertainty in the flame temperature. The technique was applied to a well-characterized premixed flat flame, the soot properties of which had been previously thoroughly investigated. Received: 21 June 2000 / Revised version: 11 September 2000 / Published online: 7 February 2001     

Numerical investigation of the effect of signal trapping on soot measurements using LII in laminar coflow diffusion flames

Laser-induced incandescence has been rapidly developed into a powerful diagnostic technique for measurements of soot in many applications. The incandescence intensity generated by laser-heated soot particles at the measurement location suffers the signal trapping effect caused by absorption and scattering by soot particles present between the measurement location and the detector. The signal trapping effect was numerically investigated in soot measurements using both a 2D LII setup and the corresponding point LII setup at detection wavelengths of 400 and 780 nm in a laminar coflow ethylene/air flame. The radiative properties of aggregated soot particles were calculated using the Rayleigh–Debye–Gans polydisperse fractal aggregate theory. The radiative transfer equation in emitting, absorbing, and scattering media was solved using the discrete-ordinates method. The radiation intensity along an arbitrary direction was obtained using the infinitely small weight technique. The contribution of scattering to signal trapping was found to be negligible in atmospheric laminar diffusion flames. When uncorrected LII intensities are used to determine soot particle temperature and the soot volume fraction, the errors are smaller in 2D LII setup where soot particles are excited by a laser sheet. The simple Beer–Lambert exponential attenuation relationship holds in LII applications to axisymmetric flames as long as the effective extinction coefficient is adequately defined.     

Relationship between soot volume fraction and LII signal in AC-LII: effect of primary soot particle diameter polydispersity

Theoretical analysis and numerical calculations were conducted to investigate the relationship between soot volume fraction and laser-induced incandescence (LII) signal within the context of the auto-compensating LII technique. The emphasis of this study lies in the effect of primary soot particle diameter polydispersity. The LII model was solved for a wide range of primary soot particle diameters from 2 to 80 nm. For a log-normally distributed soot particle ensemble encountered in a typical laminar diffusion flame at atmospheric pressure, the LII signals at 400 and 780 nm were calculated. To quantify the effects of sublimation and differential conduction cooling on the determined soot volume fraction in auto-compensating LII, two new quantities were introduced and demonstrated to be useful in LII study: an emission intensity distribution function and a scaled soot volume fraction. When the laser fluence is sufficiently low to avoid soot mass loss due to sublimation, accurate soot volume fraction can be obtained as long as the LII signals are detected within the first 200 ns after the onset of the laser pulse. When the laser fluence is in the high fluence regime to induce significant sublimation, however, the LII signals should be detected as early as possible even before the laser pulse reaches its peak when the laser fluence is sufficiently high. The analysis method is shown to be useful to provide guidance for soot volume fraction measurements using the auto-compensating LII technique.     

Soot formation characteristics in a lab-scale turbulent pulverized coal flame with simultaneous planar measurements of laser induced incandescence of soot and Mie scattering of pulverized coal

Soot formation characteristics of a lab-scale pulverized coal flame were investigated by performing carefully controlled laser diagnostics. The spatial distributions of soot volume fraction and the pulverized coal particles were measured simultaneously by laser induced incandescence (LII) and Mie scattering imaging, respectively. In addition, the radial distributions of the soot volume fraction were compared with the OH radical fluorescence, gas temperature and oxygen concentration obtained in our previous studies [1], [2]. The results indicated that the laser pulse fluence used for LII measurement should be carefully controlled to measure the soot volume fraction in pulverized coal flames. To precisely measure the soot volume fraction in pulverized coal flames using LII, it is necessary to adjust the laser pulse fluence so that it is sufficiently high to heat up all the soot particles to the sublimation temperature but also sufficiently low to avoid including a too large of a change in the morphology of the soot particles and the superposition of the LII signal from the pulverized coal particles on that from the soot particles. It was also found that the radial position of the peak LII signal intensity was located between the positions of the peak Mie scattering signal intensity and peak OH radical signal intensity. The region, in which LII signal, OH radical fluorescence and Mie scattering coexisted, expanded with increasing height above the burner port. It was also found that the soot formation in pulverized coal flames was enhanced at locations where the conditions of high temperature, low oxygen concentration and the existence of pulverized coal particles were satisfied simultaneously.     

LII–lidar: range-resolved backward picosecond laser-induced incandescence

A novel concept for remote in situ detection of soot emissions by a combination of laser-induced incandescence (LII) and light detection and ranging (lidar) is presented. A lidar setup based on a picosecond Nd:YAG laser and time-resolved signal detection in the backward direction was used for LII measurements in sooty premixed ethylene–air flames. Measurements of LII–lidar signal versus laser fluence and flame equivalence ratio showed good qualitative agreement with data reported in literature. The LII–lidar signal showed a decay consisting of two components, with lifetimes of typically 20 and 70 ns, attributed to soot sublimation and conductive cooling, respectively. Theoretical considerations and analysis of the LII–lidar signal showed that the derivative was proportional to the maximum value, which is an established measure of soot volume fraction. Utilizing this, differentiation of LII–lidar data gave profiles representing soot volume fraction with a range resolution of ~16 cm along the laser beam propagation axis. The accuracy of the evaluated LII-profiles was confirmed by comparison with LII-data measured simultaneously employing conventional right-angle detection. Thus, LII–lidar provides range-resolved single-ended detection, resourceful when optical access is restricted, extending the LII technique and opening up new possibilities for laser-based diagnostics of soot and other carbonaceous particles.     

The influence of wavelength in extinction measurements and beam steering in laser-induced incandescence measurements in sooting flames

The accuracy of laser-induced incandescence (LII) measurements is significantly influenced by the calibration process and the laser profile degradation due to beam steering. Additionally, the wavelength used for extinction measurements, needed for LII calibration, is critical and should be kept as high as possible in order to avoid light absorption by molecular species in the flame. The influence of beam steering on the LII measurement was studied in turbulent sooting C₂H₄/air flames at different pressures. While inhomogeneities in the laser profile become smoothed out in time-averaged measurements, especially at higher pressure, the corresponding single-shot beam profiles reveal an increasing effect of beam steering. In the current configuration it was observed that the resulting local laser fluence remains within certain limits (30% to 200%) of the original value. A sufficiently high incident laser fluence can thus prevent the local fluence from dropping below the LII threshold value of approximately 0.3 J/cm² at the cost of increased soot surface vaporization. A spatial resolution in the dimension of the sheet thickness of below 1 mm cannot be guaranteed at increased pressure of 9 bars due to beam steering. A feasibility study in a combustor at technical conditions demonstrates the influence of both effects beam steering and choice of calibration wavelength and led to the conclusion that, however, a shot-to-shot calibration of LII with simultaneously measured extinction can be realized.     

Effects of soot absorption and scattering on LII intensities in laminar coflow diffusion flames

Absorption and scattering of laser-induced incandescence (LII) intensities by soot particles present between the measurement volume and the detector were numerically investigated at detection wavelengths of 400 and 780 nm in a laminar coflow ethylene/air flame. The radiative properties of aggregated soot particles were calculated using the Rayleigh-Debye-Gans polydisperse fractal aggregate theory. The radiative transfer equation in emitting, absorbing, and scattering media was solved using the discrete-ordinates method. The radiation intensity along an arbitrary direction was obtained using the infinitely small weight technique. The effects of absorption and scattering on LII intensities are found to be significant under the conditions of this study, especially at the shorter detection wavelength and when the soot volume fraction is higher. Such a wavelength-dependent signal-trapping effect leads to a lower soot particle temperature estimated from the ratio of uncorrected LII intensities at the two detection wavelengths. The corresponding soot volume fraction derived from the absolute LII intensity technique is overestimated. The Beer-Lambert relationship can be used to describe radiation attenuation in absorbing and scattering media with good accuracy provided the effective extinction coefficient is adequately.     

Investigation on the influence of soot size on prompt LII signals in flames

Theoretical papers predict that prompt LII signals are weakly dependent on the soot size due to the fact that larger particles reach higher temperatures during the heating process by nanosecond laser pulses. This question is of crucial importance for establishing LII as a practical technique for soot volume fraction measurements. In this work two-color prompt LII measurements have been performed in several locations of diffusion and rich premixed ethylene-air flames. The experimental apparatus was carefully designed with a probe volume of uniform light distribution and sharp edges, a 4 ns integration time around the signal pulse peak and narrow spectral bandwidth. Measurements did not confirm the theoretical predictions concerning an increase of temperature for larger particles. On the contrary, larger particles in richer premixed flames exhibit a lower 400/700 signal ratio. This can probably be attributed to small differences in the refractive index of soot.     

Influence of long pulse duration on time-resolved laser-induced incandescence

Time-resolved laser-induced incandescence (LII) signal of soot in an ethylene laminar diffusion flame was measured with varying laser pulse durations in the range 50–600 ns. This study presents original results since the majority of LII studies reported are based on 7–10-ns pulse duration. The LII signal from soot is a combination of heating and cooling processes of different time scales, and the influence of the pulse duration is therefore particularly relevant. The most striking finding is that when the pulse durations is longer than approximately 100 ns, the time-resolved LII signal reveals a rebound of the LII signal during its slow decaying part. This feature occurs preferably at high fluence and is unexpected as none of the physical and chemical processes known to control LII signal behaviour, and their models suggest such an effect. The phenomenon occurs with both top hat and near Gaussian temporal laser shapes. Inspection of the time-resolved emission spectra shows no indication of a laser-induced fluorescence effect, although gas-phase PAH generated during the laser heating of soot particles cannot be rejected. Other hypotheses are that the mechanism responsible for that behaviour is linked to a slow rate change of the soot morphological characteristics or to the generation of new particles during the long-duration laser excitation. Finally, experiments show that soot volume fraction measured by integrating the temporal LII signal is not affected by the pulse duration in any regions of the flame, implying that the LII method is applicable with long pulse duration lasers.     

Laser induced incandescence measurements of soot volume fraction and effective particle size in a laminar co-annular non-premixed methane/air flame at pressures between 0.5–4.0 MPa

An auto-compensating laser-induced incandescence (AC-LII) technique was applied for the first time to measure soot volume fraction (SVF) and effective primary particle diameter (dp_eff) in a high pressure methane/air non-premixed flame. The measured dp_eff profiles had annular structures and radial symmetry, and the particle size increased with increasing pressure. LII-determined SVFs were lower than those measured by a line of sight attenuation (LOSA) technique. The LOSA measured soot volume fractions were corrected for light scattering using the Rayleigh–Debye–Gans polydisperse fractal aggregate (RDG-PFA) theory, the dp_eff data, and assumptions regarding the soot aggregate size distribution. The correction dramatically improved agreement between data obtained using these two measurement techniques. Qualitatively, soot volume distributions obtained using LII had more annular shapes than those obtained using LOSA. Nonetheless, it has been demonstrated that the AC-LII technique is very well suited for application in media where attenuation of the excitation laser pulse energy can exceed 45%. This paper also underlines the importance of correcting LOSA SVF measurements for light scattering in high pressure flames. PACS 07-60.-j; 47.70.Pq; 65.80.+n; 78.67.-n     

Experimental and theoretical comparison of spatially resolved laser-induced incandescence (LII) signals of soot in backward and right-angle configuration

In-situ measurements of soot volume fraction in the exhausts of jet engines can be carried out using the laser-induced incandescence (LII) technique in backward configuration, in which the signal is detected in the opposite direction of the laser beam propagation. In order to improve backward LII for quantitative measurements, we have in this work made a detailed experimental and theoretical investigation in which backward LII has been compared with the more commonly used right-angle LII technique. Both configurations were used in simultaneous visualization experiments at various pulse energies and gate timings in a stabilized methane diffusion flame. The spatial near-Gaussian laser energy distribution was monitored on-line as well as the time-resolved LII signal. A heat and mass transfer model for soot particles exposed to laser radiation was used to theoretically predict both the temporal and spatial LII signals. Comparison between experimental and theoretical LII signals indicates similar general behaviour, for example the broadening of the spatial LII distribution and the hole-burning effect at centre of the beam due to sublimation for increasing laser pulse energies. However, our comparison also indicates that the current heat and mass transfer model overpredicts signal intensities at higher fluence, and possible reasons for this behaviour are discussed. PACS 42.62.Fi; 44.40.+a     

Combination of LII and extinction measurements for determination of soot volume fraction and estimation of soot maturity in non-premixed laminar flames

The measurement of soot and soot precursors is important for understanding the formation of soot particles in flames. In this paper, we use the difference between laser-induced incandescence (LII) and two-dimensional extinction measurements to assess the contribution of soot precursors to the extinction measurement. LII measurements are performed with a high spatial resolution of 100 µm to determine the soot volume fraction (f _V) in a laminar ethylene/air non-premixed flame at the standard Gülder conditions. While LII is specific to mature soot only, the extinction data represent attenuation due to mature and young soot (absorption and elastic scattering) and also absorption by soot precursors. The difference between the two measurements indicates the contribution of soot precursors and allows a determination of the maturity of soot. This is important knowledge for those using extinction techniques to measure soot concentration, as the contribution from soot precursors may lead to an overestimation of the mature soot concentration. Further, regions with high soot-precursor concentrations, which lead to soot formation, can be identified.     

Soot volume fraction measurements in aero-engine exhausts using extinction-calibrated backward laser-induced incandescence

Control and reduction of soot particle emissions from aeronautic turbines requires a monitoring system suitable for quantification of these emissions. Currently, such emissions are estimated using the technique of smoke number. This is an extractive method, which is not sensitive enough for the low emission levels of modern gas turbines. Within a recent European project, AEROTEST, part of the project aimed at investigating an alternative soot monitoring technique, laser-induced incandescence (LII) as an in-situ optical diagnostic for quantification of soot emissions. For aero-engine applications, especially those involving large-scale turbines, it is necessary to perform the measurements at long distance from the turbine. The LII technique is favourable in this respect as it provides for non-intrusive measurements and, by detecting the isotropic LII signal along the same axis as the incoming laser beam (so called backward LII), both the laser and the detector can be built inside one system located several meters from the turbine. The concept was initiated in the previous European projects, AEROJET I and II. This paper describes the modified version of the system and the procedure developed to achieve reliable and quantitative soot volume fraction measurements in the exhausts of aero-engines. Application of the backward LII technique is demonstrated in the exhaust of a military turbojet engine for different engine speeds.     

Soot sublimation studies in a premixed flat flame using laser-induced incandescence (LII) and elastic light scattering (ELS)

Laser-induced incandescence (LII) as a diagnostic technique is based on rapid heating of soot particles to temperatures of several thousand Kelvin and subsequent detection of the thermal radiation from the laser-heated particles. At such high temperatures, soot sublimation effects must be considered when estimating uncertainties in LII measurements. In this work we have investigated the use of various laser fluences in LII using a Nd:YAG laser at 1,064 nm. Using another Nd:YAG laser at 532 nm, the elastic light scattering (ELS) signal from soot particles heated by the 1,064-nm laser was monitored. This approach makes it possible to determine at which fluence of the LII laser soot sublimation starts to become visible as a decrease in the ELS signal. By performing the measurements at various heights in a premixed sooting flat ethylene/air flame, the fluence threshold above which the ELS signal decreased was found to be higher at the lower flame heights corresponding to younger, smaller and less aggregated particles. The results from this work indicate that the different fluence thresholds for sublimation may be explained by a lower absorption function E(m) for the younger soot particles.     

Comparison of LII derived soot temperature measurements with LII model predictions for soot in a laminar diffusion flame

Laser-induced incandescence (LII) was used to derive temperatures of pulsed laser heated soot particles from their thermal emission intensities detected at two wavelengths in a laminar ethylene/air co-annular diffusion flame. The results are compared to those of a numerical nanoscale heat and mass transfer model. Both aggregate and primary particle soot size distributions were measured using transmission electron microscopy (TEM). The model predictions were numerically averaged over these experimentally derived size distributions. The excitation laser wavelength was 532 nm, and the LII signal was detected at 445 nm and 780 nm. A wide range of laser fluence from very low to moderate (0.13 to 1.56 mJ/mm²) was used in the experiments. A large part of the temporal decay curve, beginning 12–15 nsec after the peak of the laser excitation pulse, is successfully described by the model, resulting in the determination of accommodation coefficients, which varies somewhat with soot temperature and is in the range of 0.36 to 0.46. However, in the soot evaporative regime, the model greatly overpredicts the cooling rate shortly after the laser pulse. At lower fluences, where evaporation is negligible, the initial experimental cooling rates, immediately following the laser pulse, are anomalously high. Potential physical processes that could account for these effects are discussed. From the present data the soot absorption function, E(m), of 0.4 at 532 nm is obtained. A procedure for correcting the measured signals for the flame radiation is presented. It is further shown that accounting for the local gas temperature increase due to heat transfer from soot particles to the gas significantly improves the agreement in the temperature dependence of soot cooling rates between model and experiments over a large range of laser fluences.     

On the dependence of the laser-induced incandescence (LII) signal on soot volume fraction for variations in particle size

“The laser-induced incandescence (LII) signal is proportional to soot volume fraction” is an often used statement in scientific papers, and it has – within experimental uncertainties – been validated in comparisons with other diagnostic techniques in several investigations. In 1984 it was shown theoretically in a paper by Melton that there is a deviation from this statement in that the presence of larger particles leads to some overestimation of soot volume fractions. In the present paper we present a detailed theoretical investigation of how the soot particle size influences the relationship between LII signal and soot volume fraction for different experimental conditions. Several parameters have been varied; detection wavelength, time and delay of detection gate, ambient gas temperature and pressure, laser fluence, level of aggregation and spatial profile. Based on these results we are able, firstly, to understand how experimental conditions should be chosen in order to minimize the errors introduced when assuming a linear dependence between the signal and volume fraction and secondly, to obtain knowledge on how to use this information to obtain more accurate soot volume fraction data if the particle size is known. PACS 42.62.-b; 44.40.+a; 61.46.Df; 78.70.-g; 65.80.+n     

Investigation on thermal accommodation coefficient and soot absorption function with two-color Tire-LII technique in rich premixed flames

Although the two-color laser-induced incandescence technique (2C-LII) has proved to be a significant tool for soot diagnostics, many efforts are still required to gain a whole understanding of the chemical and physical processes involved. Time-resolved two-color LII measurements are carried out in a rich ethylene/air premixed flame at different heights above the burner and by changing the laser fluence. The prompt LII at two wavelengths and the corresponding soot incandescence temperature are obtained at different stages of the soot growth and under different laser irradiations. The decay rate of the LII signals, as a method for soot sizing, is investigated at different laser fluence. The time-resolved LII curves, obtained in the low laser fluence regime, are analyzed by a numerical simulation, available on the web. By considering the gas/particle initial temperature obtained with thermocouple measurements and by knowing soot particle diameter with previous TEM and extinction/scattering measurements, information about soot parameters, such as absorption function and thermal accommodation coefficient are obtained. The presence of the so-called young or mature soot along the flame height is strictly related to different optical and heat-exchange properties necessary to fit all the experimental data available.     

Influence of spatial laser energy distribution on evaluated soot particle sizes using two-colour laser-induced incandescence in a flat premixed ethylene/air flame

Time-resolved laser-induced incandescence (LII) has been developed rapidly during the last decade as a useful non-intrusive technique for particle size determination. Still several parameters should be investigated in order to improve the accuracy of LII for particle sizing and the spatial distribution of the laser energy is one of these. Generally a top-hat profile is recommended, as this ensures a uniform heating of all particles in the measurement volume. As it is generally not straightforward to create a uniform beam profile, it is of interest to establish the influence of various profiles on the evaluated particle sizes. In this work we present both an experimental and a theoretical investigation of the influence of the spatial profile on evaluated sizes. All experiments were carried out using a newly developed setup for two-colour LII (2C-LII) which provides online monitoring of both the spatial and temporal profile as well as the laser pulse energy. The LII measurements were performed in a one-dimensional premixed sooting ethylene/air flame, and evaluated particle sizes from LII were compared with thermophoretically sampled soot particles analysed using transmission electron microscopy (TEM). The results show that although there is some influence of the spatial laser energy distribution on the evaluated particle sizes both in modelling and experiments, this effect is substantially smaller than the influence of the uncertainties in gas temperature and the thermal accommodation coefficient.     

Peak soot temperature in laser-induced incandescence measurements

In order to understand the processes involved in the laser-induced incandescence (LII) technique, the value of soot temperature at the peak of the incandescence signal has been studied. To this purpose, an absolute two-color LII technique has been applied on ethylene and methane diffusion flames, based on the comparison with a calibrated tungsten ribbon lamp. The dependence of peak temperature on the fluence has been investigated by using a sharply edged probe beam. Above a certain fluence threshold a value close to 4000 K was obtained for both flames at all locations, that means in largely different soot conditions. At a suitably selected laser fluence, radial and axial profiles of peak soot temperature and volume fraction were performed. Soot volume fraction data have been validated with results from laser extinction technique measurements. The quite low values observed for methane prove the sensitivity of the LII technique. Moreover, a discussion about soot refractive index is presented. In the visible region a test of its influence on both soot volume fraction and soot peak temperature was carried out, while in the infrared the heating process was analyzed. PACS 42.62.b; 42.87-d; 44.40+a     

2D soot concentration and burning rate of a vertical PMMA slab using Laser-Induced Incandescence

In the field of fire studies, it is interesting to provide useful data for the validation of soot production and radiation models. 2D soot concentration in the flame and burning rate of the solid surface have been determined in the case of the combustion of a vertical PMMA slab. The local soot concentration has been measured with the Laser-Induced Incandescence method. This one has been calibrated with in situ extinction measurements performed simultaneously (at 1064 nm). The interference signals of LII caused by laser scattering and Laser-Induced fluorescence have been considered and eliminated by a well suited detection. The flat field effect caused by the ICCD camera has also been corrected. The trapping effect on the LII signal has also been considered. The flame grows on the slab after the ignition, and after 1500 s a steady state of combustion appears. During this period, the soot profiles in the boundary layer have been measured at two heights in the flame and their main features will be discussed. It has been possible to determine the burning rate of the PMMA slab from the observation of the displacement of soot profiles in the camera field. The values at both heights are respectively 5.55 and 6.95 g/s/m². These values will be compared with results obtained in other studies.