Soot formation characteristics in a lab-scale turbulent pulverized coal flame with simultaneous planar measurements of laser induced incandescence of soot and Mie scattering of pulverized coal

Soot formation characteristics of a lab-scale pulverized coal flame were investigated by performing carefully controlled laser diagnostics. The spatial distributions of soot volume fraction and the pulverized coal particles were measured simultaneously by laser induced incandescence (LII) and Mie scattering imaging, respectively. In addition, the radial distributions of the soot volume fraction were compared with the OH radical fluorescence, gas temperature and oxygen concentration obtained in our previous studies [1], [2]. The results indicated that the laser pulse fluence used for LII measurement should be carefully controlled to measure the soot volume fraction in pulverized coal flames. To precisely measure the soot volume fraction in pulverized coal flames using LII, it is necessary to adjust the laser pulse fluence so that it is sufficiently high to heat up all the soot particles to the sublimation temperature but also sufficiently low to avoid including a too large of a change in the morphology of the soot particles and the superposition of the LII signal from the pulverized coal particles on that from the soot particles. It was also found that the radial position of the peak LII signal intensity was located between the positions of the peak Mie scattering signal intensity and peak OH radical signal intensity. The region, in which LII signal, OH radical fluorescence and Mie scattering coexisted, expanded with increasing height above the burner port. It was also found that the soot formation in pulverized coal flames was enhanced at locations where the conditions of high temperature, low oxygen concentration and the existence of pulverized coal particles were satisfied simultaneously.     

Laser-induced incandescence for soot particle size and volume fraction measurements using on-line extinction calibration

A novel technique for two-dimensional measurements of soot volume fraction and particle size has been developed. It is based on a combined measurement of extinction and laser-induced incandescence using Nd:YAG laser wavelengths of 532 nm and 1064 nm. A low-energy laser pulse at 532 nm was used for extinction measurements and was followed by a more intense pulse at 1064 nm, delayed by 15 ns, for LII measurements. The 532-nm beam was split into a signal beam passing the flame and a reference beam, both of which were directed to a dye cell. The resulting fluorescence signals, from which the extinction was deduced, together with the LII signal, were registered on a single CCD detector. Thus the two-dimensional LII image could be converted to a soot volume fraction map through a calibration procedure during the same laser shot. The soot particle sizes were evaluated from the ratio of the temporal LII signals at two gate time positions. The uncertainty in the particle sizing arose mainly from the low signal for small particles at long gate times and the uncertainty in the flame temperature. The technique was applied to a well-characterized premixed flat flame, the soot properties of which had been previously thoroughly investigated. Received: 21 June 2000 / Revised version: 11 September 2000 / Published online: 7 February 2001     

Experimental and theoretical comparison of spatially resolved laser-induced incandescence (LII) signals of soot in backward and right-angle configuration

In-situ measurements of soot volume fraction in the exhausts of jet engines can be carried out using the laser-induced incandescence (LII) technique in backward configuration, in which the signal is detected in the opposite direction of the laser beam propagation. In order to improve backward LII for quantitative measurements, we have in this work made a detailed experimental and theoretical investigation in which backward LII has been compared with the more commonly used right-angle LII technique. Both configurations were used in simultaneous visualization experiments at various pulse energies and gate timings in a stabilized methane diffusion flame. The spatial near-Gaussian laser energy distribution was monitored on-line as well as the time-resolved LII signal. A heat and mass transfer model for soot particles exposed to laser radiation was used to theoretically predict both the temporal and spatial LII signals. Comparison between experimental and theoretical LII signals indicates similar general behaviour, for example the broadening of the spatial LII distribution and the hole-burning effect at centre of the beam due to sublimation for increasing laser pulse energies. However, our comparison also indicates that the current heat and mass transfer model overpredicts signal intensities at higher fluence, and possible reasons for this behaviour are discussed. PACS 42.62.Fi; 44.40.+a     

Laser-induced incandescence technique to identify soot nucleation and very small particles in low-pressure methane flames

This paper presents the study we carried out on the formation of soot particles in low-pressure premixed CH₄/O₂/N₂ flames by using Laser-Induced Incandescence (LII). Flames were stabilised at 26.6 kPa (200 torr). Four different equivalence ratios were tested (Φ = 1.95, 205, 2.15 and 2.32), Φ = 1.95 corresponding to the equivalence ratio for which LII signals begin to be measurable along the flame. The evolution of the LII signals with laser fluence (fluence curve), time (temporal decay) and emission wavelength is reported at different heights above the burner. We specifically took advantage of the low-pressure conditions to probe with a good spatial resolution the soot inception zone of the flames. Significant different behaviours of the fluence curves are observed according to the probed region of the flames and Φ. In addition, while the surface growth process is accompanied by an increase in the LII decay-times (indicator of the primary particle diameter) at higher Φ, decay-times become increasingly short at lower Φ reaching a constant value along the flame at Φ = 1.95. These behaviours are consistent with the detection of the smallest incandescent particles in the investigated flames, these particles having experienced very weak surface growth. Flame modelling including soot formation has been implemented in flames Φ = 2.05 and 2.32. Experimental quantitative soot volume fraction profiles were satisfactorily reproduced by adjusting the fraction of reactive soot surface available for reactions. The qualitative variation of the computed soot particle diameter and the relative weight of surface growth versus nucleation were consistent with the experimental observations.     

Soot sublimation studies in a premixed flat flame using laser-induced incandescence (LII) and elastic light scattering (ELS)

Laser-induced incandescence (LII) as a diagnostic technique is based on rapid heating of soot particles to temperatures of several thousand Kelvin and subsequent detection of the thermal radiation from the laser-heated particles. At such high temperatures, soot sublimation effects must be considered when estimating uncertainties in LII measurements. In this work we have investigated the use of various laser fluences in LII using a Nd:YAG laser at 1,064 nm. Using another Nd:YAG laser at 532 nm, the elastic light scattering (ELS) signal from soot particles heated by the 1,064-nm laser was monitored. This approach makes it possible to determine at which fluence of the LII laser soot sublimation starts to become visible as a decrease in the ELS signal. By performing the measurements at various heights in a premixed sooting flat ethylene/air flame, the fluence threshold above which the ELS signal decreased was found to be higher at the lower flame heights corresponding to younger, smaller and less aggregated particles. The results from this work indicate that the different fluence thresholds for sublimation may be explained by a lower absorption function E(m) for the younger soot particles.     

2D imaging of laser wing effects and of soot sublimation in laser-induced incandescence measurements

The distribution of Laser-Induced Incandescence (LII) signal in sooting flames along the laser beam is imaged using two directions of observation: one counter to the propagation direction of the incident laser (backward LII) and one at right angles. It is shown that the effective probe volume, in which the LII signal is observed, is highly dependent on the laser irradiance profile. At high fluence, the LII from the central part of the beam decreases because of soot sublimation. This decrease can be compensated by an increase in the LII from the wings of the laser beam. This interaction is particularly important in the extraction of quantitative information in the backward LII case, which is the configuration best suited to the practical application of LII for in-situ particle concentration measurements in the exhaust of aero-engines.     

Peak soot temperature in laser-induced incandescence measurements

In order to understand the processes involved in the laser-induced incandescence (LII) technique, the value of soot temperature at the peak of the incandescence signal has been studied. To this purpose, an absolute two-color LII technique has been applied on ethylene and methane diffusion flames, based on the comparison with a calibrated tungsten ribbon lamp. The dependence of peak temperature on the fluence has been investigated by using a sharply edged probe beam. Above a certain fluence threshold a value close to 4000 K was obtained for both flames at all locations, that means in largely different soot conditions. At a suitably selected laser fluence, radial and axial profiles of peak soot temperature and volume fraction were performed. Soot volume fraction data have been validated with results from laser extinction technique measurements. The quite low values observed for methane prove the sensitivity of the LII technique. Moreover, a discussion about soot refractive index is presented. In the visible region a test of its influence on both soot volume fraction and soot peak temperature was carried out, while in the infrared the heating process was analyzed. PACS 42.62.b; 42.87-d; 44.40+a     

Modeling laser-induced incandescence of soot: a summary and comparison of LII models

We have performed a comparison of ten models that predict the temporal behavior of laser-induced incandescence (LII) of soot. In this paper we present a summary of the models and comparisons of calculated temperatures, diameters, signals, and energy-balance terms. The models were run assuming laser heating at 532 nm at fluences of 0.05 and 0.70 J/cm² with a laser temporal profile provided. Calculations were performed for a single primary particle with a diameter of 30 nm at an ambient temperature of 1800 K and a pressure of 1 bar. Preliminary calculations were performed with a fully constrained model. The comparison of unconstrained models demonstrates a wide spread in calculated LII signals. Many of the differences can be attributed to the values of a few important parameters, such as the refractive-index function E(m) and thermal and mass accommodation coefficients. Constraining these parameters brings most of the models into much better agreement with each other, particularly for the low-fluence case. Agreement among models is not as good for the high-fluence case, even when selected parameters are constrained. The reason for greater variability in model results at high fluence appears to be related to solution approaches to mass and heat loss by sublimation. PACS 65.80.+n; 78.20.Nv; 42.62.-b; 44.05.+e     

Investigation on thermal accommodation coefficient and soot absorption function with two-color Tire-LII technique in rich premixed flames

Although the two-color laser-induced incandescence technique (2C-LII) has proved to be a significant tool for soot diagnostics, many efforts are still required to gain a whole understanding of the chemical and physical processes involved. Time-resolved two-color LII measurements are carried out in a rich ethylene/air premixed flame at different heights above the burner and by changing the laser fluence. The prompt LII at two wavelengths and the corresponding soot incandescence temperature are obtained at different stages of the soot growth and under different laser irradiations. The decay rate of the LII signals, as a method for soot sizing, is investigated at different laser fluence. The time-resolved LII curves, obtained in the low laser fluence regime, are analyzed by a numerical simulation, available on the web. By considering the gas/particle initial temperature obtained with thermocouple measurements and by knowing soot particle diameter with previous TEM and extinction/scattering measurements, information about soot parameters, such as absorption function and thermal accommodation coefficient are obtained. The presence of the so-called young or mature soot along the flame height is strictly related to different optical and heat-exchange properties necessary to fit all the experimental data available.     

LII–lidar: range-resolved backward picosecond laser-induced incandescence

A novel concept for remote in situ detection of soot emissions by a combination of laser-induced incandescence (LII) and light detection and ranging (lidar) is presented. A lidar setup based on a picosecond Nd:YAG laser and time-resolved signal detection in the backward direction was used for LII measurements in sooty premixed ethylene–air flames. Measurements of LII–lidar signal versus laser fluence and flame equivalence ratio showed good qualitative agreement with data reported in literature. The LII–lidar signal showed a decay consisting of two components, with lifetimes of typically 20 and 70 ns, attributed to soot sublimation and conductive cooling, respectively. Theoretical considerations and analysis of the LII–lidar signal showed that the derivative was proportional to the maximum value, which is an established measure of soot volume fraction. Utilizing this, differentiation of LII–lidar data gave profiles representing soot volume fraction with a range resolution of ~16 cm along the laser beam propagation axis. The accuracy of the evaluated LII-profiles was confirmed by comparison with LII-data measured simultaneously employing conventional right-angle detection. Thus, LII–lidar provides range-resolved single-ended detection, resourceful when optical access is restricted, extending the LII technique and opening up new possibilities for laser-based diagnostics of soot and other carbonaceous particles.     

Laser induced incandescence measurements of soot volume fraction and effective particle size in a laminar co-annular non-premixed methane/air flame at pressures between 0.5–4.0 MPa

An auto-compensating laser-induced incandescence (AC-LII) technique was applied for the first time to measure soot volume fraction (SVF) and effective primary particle diameter (dp_eff) in a high pressure methane/air non-premixed flame. The measured dp_eff profiles had annular structures and radial symmetry, and the particle size increased with increasing pressure. LII-determined SVFs were lower than those measured by a line of sight attenuation (LOSA) technique. The LOSA measured soot volume fractions were corrected for light scattering using the Rayleigh–Debye–Gans polydisperse fractal aggregate (RDG-PFA) theory, the dp_eff data, and assumptions regarding the soot aggregate size distribution. The correction dramatically improved agreement between data obtained using these two measurement techniques. Qualitatively, soot volume distributions obtained using LII had more annular shapes than those obtained using LOSA. Nonetheless, it has been demonstrated that the AC-LII technique is very well suited for application in media where attenuation of the excitation laser pulse energy can exceed 45%. This paper also underlines the importance of correcting LOSA SVF measurements for light scattering in high pressure flames. PACS 07-60.-j; 47.70.Pq; 65.80.+n; 78.67.-n     

Influence of long pulse duration on time-resolved laser-induced incandescence

Time-resolved laser-induced incandescence (LII) signal of soot in an ethylene laminar diffusion flame was measured with varying laser pulse durations in the range 50–600 ns. This study presents original results since the majority of LII studies reported are based on 7–10-ns pulse duration. The LII signal from soot is a combination of heating and cooling processes of different time scales, and the influence of the pulse duration is therefore particularly relevant. The most striking finding is that when the pulse durations is longer than approximately 100 ns, the time-resolved LII signal reveals a rebound of the LII signal during its slow decaying part. This feature occurs preferably at high fluence and is unexpected as none of the physical and chemical processes known to control LII signal behaviour, and their models suggest such an effect. The phenomenon occurs with both top hat and near Gaussian temporal laser shapes. Inspection of the time-resolved emission spectra shows no indication of a laser-induced fluorescence effect, although gas-phase PAH generated during the laser heating of soot particles cannot be rejected. Other hypotheses are that the mechanism responsible for that behaviour is linked to a slow rate change of the soot morphological characteristics or to the generation of new particles during the long-duration laser excitation. Finally, experiments show that soot volume fraction measured by integrating the temporal LII signal is not affected by the pulse duration in any regions of the flame, implying that the LII method is applicable with long pulse duration lasers.     

The effects of pulsed laser injection seeding and triggering on the temporal behavior and magnitude of laser-induced incandescence from soot

The effect of sub-nanosecond fluence fluctuations and triggering on time-resolved laser-induced incandescence (LII) from soot has been studied using an injection-seeded pulsed Nd:YAG laser that produces a smooth laser temporal profile. Without injection seeding, this multi-mode laser generates pulses with large intensity fluctuations with sub-nanosecond rise times. The experimental results described here demonstrate that at fluences below 0.6 J/cm² LII signals are insensitive to fluence fluctuations on nanosecond time scales. At fluences above 0.6 J/cm² fluctuations in the laser profile cause the rising edge of the LII profile to move around in time relative to the center of the laser pulse causing a broader average profile that shifts to earlier times. Such fluctuations also lead to a decrease in the average LII temporal profile by up to 12% at a fluence of 3.5 J/cm². A timing jitter on the trigger of the data acquisition, such as that produced by triggering on the laser Q-switch synchronization pulse, has a negligible effect on the shape and temporal maximum of the LII signal. Additional jitter, however, considerably reduces the peak of the LII temporal profiles at fluences as low as 0.15 J/cm². Neither fast fluence fluctuations nor trigger jitter have a significant effect on gated LII signals, such as those used to infer soot volume fraction.     

Determination of the ratio of soot refractive index function E(m) at the two wavelengths 532 and 1064 nm by laser induced incandescence

A new method is proposed to measure the ratio of the refractive index function of soot particles E(m) at the two fixed wavelengths: 532 and 1064 nm. Using a non-intrusive, in-situ laser based technique, the ratio E(m,1064 nm)/E(m,532 nm) can be determined by comparing laser induced incandescence (LII) intensities at 532 and 1064 nm excitation wavelengths. The method consists of selecting laser energies that insure the equality of the LII signals in the low fluence regime under given conditions. Such equality is consistent with the fact that the soot particle will have reached the same temperature independently of the laser wavelength, i.e. the soot particle has absorbed the same energy. As the absorbed energy is proportional to the laser irradiance times E(m), the measurement of the laser energies required to insure perfect concordance of the LII intensities (spatially and temporally) serves to deduce the ratio E(m,1064 nm)/E(m,532 nm). The method is demonstrated in an acetylene/air flame, validated against extinction measurements performed by cavity ring-down spectroscopy (CRDS) by using laser radiations at 532 nm and 1064 nm and finally applied to different flame conditions. PACS 78.20.Ci; 78.90.+t; 81.05.Uw; 42.62.-b     

Numerical investigation of the effect of signal trapping on soot measurements using LII in laminar coflow diffusion flames

Laser-induced incandescence has been rapidly developed into a powerful diagnostic technique for measurements of soot in many applications. The incandescence intensity generated by laser-heated soot particles at the measurement location suffers the signal trapping effect caused by absorption and scattering by soot particles present between the measurement location and the detector. The signal trapping effect was numerically investigated in soot measurements using both a 2D LII setup and the corresponding point LII setup at detection wavelengths of 400 and 780 nm in a laminar coflow ethylene/air flame. The radiative properties of aggregated soot particles were calculated using the Rayleigh–Debye–Gans polydisperse fractal aggregate theory. The radiative transfer equation in emitting, absorbing, and scattering media was solved using the discrete-ordinates method. The radiation intensity along an arbitrary direction was obtained using the infinitely small weight technique. The contribution of scattering to signal trapping was found to be negligible in atmospheric laminar diffusion flames. When uncorrected LII intensities are used to determine soot particle temperature and the soot volume fraction, the errors are smaller in 2D LII setup where soot particles are excited by a laser sheet. The simple Beer–Lambert exponential attenuation relationship holds in LII applications to axisymmetric flames as long as the effective extinction coefficient is adequately defined.     

On the dependence of the laser-induced incandescence (LII) signal on soot volume fraction for variations in particle size

“The laser-induced incandescence (LII) signal is proportional to soot volume fraction” is an often used statement in scientific papers, and it has – within experimental uncertainties – been validated in comparisons with other diagnostic techniques in several investigations. In 1984 it was shown theoretically in a paper by Melton that there is a deviation from this statement in that the presence of larger particles leads to some overestimation of soot volume fractions. In the present paper we present a detailed theoretical investigation of how the soot particle size influences the relationship between LII signal and soot volume fraction for different experimental conditions. Several parameters have been varied; detection wavelength, time and delay of detection gate, ambient gas temperature and pressure, laser fluence, level of aggregation and spatial profile. Based on these results we are able, firstly, to understand how experimental conditions should be chosen in order to minimize the errors introduced when assuming a linear dependence between the signal and volume fraction and secondly, to obtain knowledge on how to use this information to obtain more accurate soot volume fraction data if the particle size is known. PACS 42.62.-b; 44.40.+a; 61.46.Df; 78.70.-g; 65.80.+n     

Optical and microscopy investigations of soot structure alterations by laser-induced incandescence

2 at 1064 nm, vaporization/fragmentation of soot primary particles and aggregates occurs. Optical measurements are performed using a second laser pulse to probe the effects of these changes upon the LII signal. With the exception of very low fluences, the structural changes induced in the soot lead to a decreased LII intensity produced by the second laser pulse. These two-pulse experiments also show that these changes do not alter the LII signal on timescales less than 1 μs for fluences below the vaporization threshold. Received: 20 October 1997/Revised version: 16 February 1998     

Comparison of LII derived soot temperature measurements with LII model predictions for soot in a laminar diffusion flame

Laser-induced incandescence (LII) was used to derive temperatures of pulsed laser heated soot particles from their thermal emission intensities detected at two wavelengths in a laminar ethylene/air co-annular diffusion flame. The results are compared to those of a numerical nanoscale heat and mass transfer model. Both aggregate and primary particle soot size distributions were measured using transmission electron microscopy (TEM). The model predictions were numerically averaged over these experimentally derived size distributions. The excitation laser wavelength was 532 nm, and the LII signal was detected at 445 nm and 780 nm. A wide range of laser fluence from very low to moderate (0.13 to 1.56 mJ/mm²) was used in the experiments. A large part of the temporal decay curve, beginning 12–15 nsec after the peak of the laser excitation pulse, is successfully described by the model, resulting in the determination of accommodation coefficients, which varies somewhat with soot temperature and is in the range of 0.36 to 0.46. However, in the soot evaporative regime, the model greatly overpredicts the cooling rate shortly after the laser pulse. At lower fluences, where evaporation is negligible, the initial experimental cooling rates, immediately following the laser pulse, are anomalously high. Potential physical processes that could account for these effects are discussed. From the present data the soot absorption function, E(m), of 0.4 at 532 nm is obtained. A procedure for correcting the measured signals for the flame radiation is presented. It is further shown that accounting for the local gas temperature increase due to heat transfer from soot particles to the gas significantly improves the agreement in the temperature dependence of soot cooling rates between model and experiments over a large range of laser fluences.     

Effect of aggregation on the absorption cross-section of fractal soot aggregates and its impact on LII modelling

This study concerns the effect of particle aggregation on laser heating rate of soot aggregates in laser-induced incandescence. Three aggregate absorption models were investigated: the Rayleigh-Debye-Gans approximation, the electrostatics approximation, and the numerically exact generalized multi-sphere Mie-solution method. Fractal aggregates containing 5-893 primary particles of 30 nm in diameter were generated numerically using a combined particle-cluster and cluster-cluster aggregation algorithm with specific fractal parameters typical of soot. The primary particle size parameters considered are 0.089, 0.177, and 0.354. The Rayleigh-Debye-Gans approximation neglects the effect of particle aggregation on absorption; so it underestimates the aggregate absorption cross-section area by approximately 10%, depending on the aggregate size and primary particle size parameter. The electrostatics approximation is somewhat better than the Rayleigh-Debye-Gans approximation, but cannot account for the effect of primary particle size parameter. The aggregate absorption submodel affects the calculated soot temperature in laser-induced incandescence mainly in the low laser fluence regime. At high laser fluences, the effect diminishes due to the enhanced importance of soot sublimation cooling and neglect of aggregation effect in the sublimation in the present numerical model of laser-induced incandescence.