基于等效源法和双面质点振速测量的声场分离方法

目前基于等效源法的声场分离方法有两种输入方式, 一种以双测量面上的声压为输入, 另一种以单测量面上的声压和质点振速为输入. 本文以双测量面上的质点振速为输入, 提出一种新的基于等效源法的声场分离方法. 首先给出了该方法的理论推导, 然后通过数值仿真和实验验证了该方法的有效性. 通过与基于双面声压测量的声场分离方法的比较, 证明了该方法在分离质点振速方面的优越性. 此外, 在仿真中还研究了干扰声源强度和测量面间距对分离精度的影响. 关键词： 声场分离 质点振速测量 等效源法 近场声全息     

基于声压-振速测量的平面近场声全息实验研究

常规的近场声全息均是采用全息面声压或质点振速作为输入量求解,由于采用单一输入量无法分离来自全息面背向声波的干扰,因此要求所有声源均位于全息面的同一侧,即测量声场为自由声场,这种要求大大限制了近场声全息的实际应用.基于声压-速度测量的近场声全息以全息面上声压和质点振速同时作为输入量,通过建立和求解两侧声源在全息面上的声压和质点振速耦合关系,可以实现全息面两侧声波的分离,从而解决上述问题.文中在前期对声场分离技术研究的基础上,基于欧拉公式和有限差分近似,推导了新的基于声压-速度测量的平面近场声全息理论公式.随后通过实验检验了该方法在有背景源干扰情况下实现声场分离和重建的有效性.     

非自由声场中目标声场还原与重建的等效源方法

为消除在非自由声场中重建声场时干扰声源对重建效果的影响,提出一种采用单个测量面上的声压和质点振速作为输入、等效源法作为分离和重建算法的非自由声场中目标声场还原与重建方法。该方法首先利用单面声压-质点振速测量和基于等效源法的声场分离技术将测量的混合声场分离为来自目标声源的向外传播的声场和来自干扰声源的向内传播的声场,然后利用向内传播的声场和目标声源的边界条件计算出干扰声在目标声源表面产生的散射声场,并将其从向外传播的声场中去除,还原出目标声源在自由声场条件下的辐射声场,最后利用还原的声场实现目标声场重建。通过数值仿真和实验检验了该方法的有效性和必要性。仿真和实验的结果表明,该方法可以在非自由声场的测量条件下,有效地去除干扰声的影响,实现目标声场的准确重建。      

基于声压-振速测量的单面声场分离技术

在近场声全息技术的基础上,研究了基于声压-质点振速测量的单面声场分离技术.分析了现有基于Fourier变换的单面声场分离技术中的奇异性问题,并应用波数域谱平均法提出了去除奇异性的修正声场分离公式.为改善分离效果,减小由于Fourier变换引起的卷绕误差等因素的影响,基于统计最优近场声全息提出了一种新的单面声场分离方法.通过仿真分析对各种单面声场分离方法做了比较,并用Microflown公司的声强探头做了基于声压-振速测量的单面声场分离实验研究,验证了提出的修正公式和基于统计最优单面声场分离方法的正确性和有效性. 关键词： 声场分离 近场声全息 统计最优 Fourier变换     

一种热对流式MEMS二维质点振速传感器

由空气质点振速传感器和声压传感器组成的矢量传声器是测量声场空间信息的重要方式。本文设计了一种新型热对流式二维质点振速传感器,不同于传统平行线式传感机制,该器件由多线进行交叉连结形成一个中央十字加热器和四个直角测温线,构成新的局域加热和温度传感方式,基于此设计能够获得更高的灵敏度并具有理想的正交性。通过数值分析对其传感机制进行了详细分析,并使用MEMS工艺进行器件制备和性能验证。实验结果表明,该器件具有良好的响应灵敏度和接近完美的正交指向性。所提出器件在体积受限的声场测量中具有潜在应用价值。     

全面感知水声信息的新传感器技术——矢量水听器及其应用

文章介绍了一种新型水声接收换能器——矢量水听器(矢量传感器),它可以同时共点地测量声场的声压和矢量(水媒质质点振速,振动加速度或声压梯度等),使用矢量水听器比常规声压水听器能获得更全面的声场信息,因此,在水声技术中获得了广泛的应用.文中描述了矢量水听器的结构设计和工作原理及特性,给出了一些重要的应用例子.     

匹配垂直质点振速的浅海地声参数反演

海底声学参数对海洋波导中的声场特性研究和相关应用具有重要意义。针对一次夏季黄海声传播实验,分析了浅海负跃层环境下垂直质点振速的传播特性和简正波结构,说明当声源和接收器均位于负跃层下时,除海底附近外的大部分深度上垂直质点振速能量较高,且与声压相比,号数高的简正波对垂直质点振速的贡献更大,利用垂直质点振速进行匹配场反演能获得更高的海底参数敏感性。分析了海底吸收系数对垂直质点振速匹配场反演的影响,结果表明只有当进行匹配场反演时设置的海底吸收系数接近真实值时,才能获得准确的海底声速、密度和海深反演结果。利用实验中矢量水听器获取的垂直质点振速信号进行匹配场反演,将海底吸收系数在变化范围内取不同值对海底声速、密度和平均海深进行全局搜索,根据代价函数值最大确定了海底声速、密度及平均海深的反演结果,并利用不同距离上的声压传播损失反演出不同频率下的海底吸收系数。根据反演得到的海底声学参数计算声压传播损失,与实验中声压水听器测量结果符合较好。     

双面声场反向神经网络声压外推分离

针对有限测量孔径造成的窗效应和离散传声器阵列带来的卷绕误差对双面声场分离技术的影响,提出了一种利用反向传播神经网络的全息面声压外推方法。该方法首先利用孔径内部测点平面坐标和相应声压值组成的学习样本训练神经网络,拟合出两者的函数关系。接着代入孔径外部测点坐标得到对应声压值,实现有限孔径外推。最后将已有测量值和外推测量值组成的虚拟大孔径导入双面声场分离处理。与传统外推方法相比,该方法不需要先验知识,操作简单,计算抗干扰能力强,结果准确性高。数值仿真和实验进一步验证了该方法在改善声场分离结果方面的可行性和有效性。      

声矢量传感器研究进展

声矢量传感器由传统的无指向性声压传感器和偶极子指向性质点振速传感器复合而成,可以同步共点测量声场中一点处的声压和质点振速若干正交分量,由此得到的幅度和相位信息为解决一些水声问题提供了新的思路。因其实际的和潜在的工程应用价值,所以在最近十年间与此相关的声矢量传感器技术备受水声界关注。本文尝试综述声矢量传感器技术近五十年间在物理基础、传感器设计制作、相关工程应用等各方面的发展历史、现状和所取得的一些研究进展。PACS数: 43.30,43.60,43.85     

基于矢量水听器的声压和质点振速的空间相关系数

矢量水听器同步测量声场空间一点处的声压和质点振速的三个正交分量,由此得到的幅度和相位信息有利于改善声呐的检测和估计性能。对三维球形各向同性噪声场中声压和质点振速的时空相关性本文进行了研究,推导了矢量水听器的噪声协方差矩阵的理论表达式;给出了矢量水听器水平线阵和垂直线阵的协方差矩阵;研究单个矢量水听器的噪声协方差矩阵,并给出了浅海近岸水域的试验结果;利用上述理论结果推导了矢量水听器阵列的声能流阵增益。     

Sound field separation with a double layer velocity transducer array (L)

In near-field acoustic holography sound field separation techniques make it possible to distinguish between sound coming from the two sides of the array. This is useful in cases where the sources are not confined to only one side of the array, e.g., in the presence of additional sources or reflections from the other side. This paper examines a separation technique based on measurement of the particle velocity in two closely spaced parallel planes. The purpose of the technique is to recover the particle velocity radiated by a source in the presence of disturbing sound from the opposite side of the array. The technique has been examined and compared with direct velocity based reconstruction, as well as with a technique based on the measurement of the sound pressure and particle velocity. The double layer velocity method circumvents some of the drawbacks of the pressure-velocity based reconstruction, and it can successfully recover the normal velocity radiated by the source, even in the presence of strong disturbing sound.     

Seabed geoacoustic characterization with a vector sensor array

This paper proposes a vector sensor measurement model and the related Bartlett estimator based on particle velocity measurements for generic parameter estimation, illustrating the advantages of the Vector Sensor Array (VSA). A reliable estimate of the seabed properties such as sediment compressional speed, density and compressional attenuation based on matched-field inversion (MFI) techniques can be achieved using a small aperture VSA. It is shown that VSAs improve the resolution of seabed parameter estimation when compared with pressure sensor arrays with the same number of sensors. The data considered herein was acquired by a four-element VSA in the 8-14 kHz band, during the Makai Experiment in 2005. The results obtained with the MFI technique are compared with those obtained with a method proposed by C. Harrison, which determines the bottom reflection loss as the ratio between the upward and downward beam responses. The results show a good agreement and are in line with the historical information for the area. The particle velocity information provided by the VSA increases significantly the resolution of seabed parameter estimation and in some cases reliable results are obtained using only the vertical component of the particle velocity.     

Modelling the pressure field in the vicinity of a microphone membrane using PIV

A new approach for estimating the acoustic pressure in the near field of a microphone based on non-intrusive direct measurement of acoustic particle velocity is proposed.This method enables the estimation of the acoustic pressure inside a domain located in front of the microphone membrane. The acoustic pressure is calculated using the acoustic particle velocity on the frontiers of this domain and a physical model based on the Green function of the system.Results are obtained using the acoustic velocity measured with Particle Image Velocimetry (PIV) in front of a microphone excited with a plane wave inside a rectangular waveguide. They show that the diffraction of the plane wave by the microphone leads to an increase of the acoustic pressure on the microphone edge in the order of magnitude of 0.1 dB.     

Simultaneous density and velocity measurements in a supersonic turbulent boundary layer

A novel technique for simultaneous measurements of instantaneous whole-field density and velocity fields of supersonic flows has been developed.The density measurement is performed based on the nano-tracer planar laser scattering(NPLS) technique,while the velocity measurement is carried out using particle image velocimetry(PIV).The present experimental technique has been applied to a flat-plate turbulent boundary layer at Mach 3,and the measurement accuracy of the density and velocity are discussed.Based on this new technique,the Reynolds stress distributions were also obtained,demonstrating that this is an effective means for measuring Reynolds stresses under compressible conditions.     

角度型表面等离子体振荡传感器测量精度提高的新方法

设计了一种基于棱镜的角度型表面等离子体振荡自动测量系统,建立了共轴双旋转台的机械结构,提出了新型扫描的角度测量法,得到表面等离子体振荡谐振曲线。研究了影响系统多次测量一致性的因素,提出了减少采样点、提高单点数据采集次数,并采用三级变步长的测量方法,测量时间缩短至小于原来的1/10,使系统测量精度从1E 4折射率单位提高到了4E-5折射率单位。     

Statistically optimized near field acoustic holography using an array of pressure-velocity probes

Statistically optimized near field acoustic holography (SONAH) differs from conventional near field acoustic holography (NAH) by avoiding spatial Fourier transforms; the processing is done directly in the spatial domain. The main advantage of SONAH compared with NAH is that the usual requirement of a measurement aperture that extends well beyond the source can be relaxed. Both NAH and SONAH are based on the assumption that all sources are on one side of the measurement plane whereas the other side is source free. An extension of the SONAH procedure based on measurement with a double layer array of pressure microphones has been suggested. The double layer technique makes it possible to distinguish between sources on the two sides of the array and thus suppress the influence of extraneous noise coming from the "wrong" side. It has also recently been demonstrated that there are significant advantages in NAH based on an array of acoustic particle velocity transducers (in a single layer) compared with NAH based on an array of pressure microphones. This investigation combines the two ideas and examines SONAH based on an array of pressure-velocity intensity probes through computer simulations as well as experimentally.     

Scanning moiré and spatial-offset phase-stepping for surface inspection of structures

In order to develop a high-speed and accurate surface inspection system of structures such as tunnels, a new surface profile measurement method using linear array sensors is studied. The sinusoidal grating is projected on a structure surface. Then, the deformed grating is scanned by linear array sensors that move together with the grating projector. The phase of the grating is analyzed by a spatial offset phase-stepping method to perform accurate measurement. The surface profile measurements of the wall with bricks and the concrete surface of a structure are demonstrated using the proposed method. The change of geometry or fabric of structures and the defects on structure surfaces can be detected by the proposed method. It is expected that the surface profile inspection system of tunnels measuring from a running train can be constructed based on the proposed method.     

梯度穿缝型双孔隙率多孔材料的吸声性能

在传统单一孔隙率多孔材料中引入宏观尺度的周期性梯度穿缝结构设计,构造出梯度穿缝型双孔隙率多孔材料,其包含多孔材料基体微孔尺度与穿缝尺度两个尺度。采用分层等效的理论建模方法,将复杂梯度渐变问题变为多层均匀等效层叠加问题。针对不同特征尺寸的多孔材料薄层,分别采用低、高两种渗透率对比度双孔隙率理论,给出了其等效密度和动态压缩系数,再应用传递矩阵方法得到了相邻薄层之间的声压和质点速度传递关系并求得其表面声阻抗,从而建立了梯度穿缝型双孔隙率多孔材料的吸声理论模型。发展了多尺度材料声学有限元数值模型,在所考虑的100~3000 Hz频段范围内数值模拟结果完全吻合理论模型结果。理论与模拟分析了多尺度结构参数对双孔隙率多孔材料吸声性能的影响,结果表明引入多尺度梯度结构设计能够显著提高单一孔隙率多孔材料的吸声性能,且穿缝尺度比穿缝梯度影响更为显著;精细数值模拟获得的声压和能量密度分布云图揭示了多尺度结构设计的吸声增强机制。该工作可用于指导双孔隙率多孔材料的多尺度结构设计,从而提高多孔材料的中低频吸声性能。      

高声压级时多孔金属板的吸声特性研究

针对高声压级下有限厚度多孔金属板在线性阻抗背衬条件下(背衬表面声压与声质点速度为线性关系)的吸声问题,提出了一个描述不同声压级下材料层法向吸声性能的一维模型,并给出求解材料层内部声质点速度的线化与差分方法,以预测多孔金属板在高声压级下的非线性吸声特性。在阻抗管中对两块多孔金属板进行了声学测试,得到了材料层法向表面阻抗和吸声系数随入射声压级变化的实验结果。研究表明:实验与理论预测符合良好,验证了模型与数值方法的正确性。本文所提原理和方法,可用于一般硬质多孔材料。