磁液磁光双稳特性的研究

本文基于磁液磁致双折射效应,实现了其磁光双稳特性的研究。理论上,建立了其磁光双稳传输模型、进行了计算机模拟,并在此基础上建立了相应的实验分析系统。研究表明:磁液薄膜具有良好的磁光双稳特性,可用作超长波红外波导器件。     

Passive mode-locking by use of waveguide arrays

A novel mode-locking technique is presented in which the intensity-dependent spatial coupling dynamics of a waveguide array is used to achieve temporal mode-locking in a passive optical fiber laser. By use of the discrete, nearest-neighbor spatial coupling of the waveguide array, low-intensity light can be transferred to the neighboring waveguides and ejected (attenuated) from the laser cavity. In contrast, higher-intensity light is self-focused in the waveguide and remains largely unaffected. Numerical studies of this pulse shaping mechanism (intensity discrimination) show that using current waveguide arrays and standard optical fiber technology produces stable and robust mode-locked soliton-like pulses.     

自由载流子吸收损耗控制研究

利用数值方法研究了SOI脊形光波导损耗问题,重点讨论了PIN结构对自由载流子损耗控制的影响情况。研究表明SOI脊形波导在引入PIN结构后,偏置电压、入射光强和本征区宽度是影响自由载流子吸收损耗的主要因素,通过调整PIN结所加偏置电压、入射光强和本征区宽度,可以实现对脊形波导自由载流子吸收损耗的控制。计算结果可为硅基光调制器和拉曼激光器的设计制备提供一定的参考依据。     

An azobenzene functionalized polymer for laser direct writing waveguide fabrication

We report on non-lithographic laser direct writing fabrication of optical waveguides by using a 4′-hydroxy-4-nitroazobene dye-functionalized polymer film. The polymer film reveals permanent change of refractive index at high laser illumination intensity. A focused continuous wave low power green laser beam at 532 nm wavelength is used to directly write waveguide structures on the polymer film. The magnitude of refractive index increase at film surface is about 0.006. One-step laser writing results in graded index waveguides in film depth direction under ambient conditions without pre- and post-processing. As a by-product, the laser writing also results in a very small air valley at the boundary between the laser written and non-written regions which may contribute in part although minimal to the waveguide lateral confinement and can be used for visual observation of waveguide patterns. The fabricated waveguide is found to be stable and easily reproducible.     

原油含水率测量的光学计量仪

油井含水率是油田开发过程中的一个重要指标。光纤传感器具有体积小、重量轻、抗干扰能力强、实时、高效、准确等优点,将其应用于石油测井,有利于提高勘探效率。介绍测井应用中原油含水率计量仪的结构,分析了光纤传感器对混合液体含水率测量的基本原理。激光在弯曲光纤中的传输效率随外界混合介质折射率的变化而改变,根据光纤输出光功率的大小可以测量外界混合介质的组成成分。通过数值模拟,给出了光纤传感器中光束强度随混合液体含水率的变化现象,计算得到混合液体中含水率测量结果。结果表明,光纤传感器计量仪能实现0%～100%含水量的连续测量。最后基于数值模拟结果讨论了系统设计中的注意事项。     

Output mode characteristics of an in-phase locked gain waveguide array CO2 laser

In this paper,experimental and theoretical studies of the output mode characteristics of an in-phase locked gain waveguide array CO 2 laser are reported.The experimental results of the optical oscillation mode frequency,the far-field intensity distribution and the burnt pattern of the sliced waveguide array laser are obtained.A revised mode expression of the rectangle waveguide,which is suited for this waveguide array CO 2 laser,is proposed.The theoretical simulation results based on the revised mode expression are shown to be in good agreement with the experimental results.     

基于波导、金和氧化锌的随机激光器的研究

通过将金属金嵌入到上下两层波导结构中,与ZnO随机粒子相结合,设计出一种新型结构的随机激光器。采用时域有限差分法(FDTD),数值模拟了该随机激光器系统的光场分布和模式频谱图,并针对金粒子和金薄膜两种情况进行对比分析。结果显示,采用金粒子作夹层时,出射激光模式数量减少,单色性较好;采用金薄膜作夹层时,出射激光光强较大。     

基于倏逝场耦合的石墨烯波导光传输相位特性仿真与实验研究

石墨烯材料应用到各种光波导器件中正成为新一代光子器件的重要发展方向之一,目前基于石墨烯的光纤和集成光子器件研究越来越受到国内外的重视. 本文建立了一种由微纳光纤耦合光倏逝场,并在石墨烯薄膜中传输的模型. 通过有限元分析法,研究了光在这种石墨烯波导中传输光场的强度分布和相位特性,并通过实验进行了验证. 结果表明,沿着微纳光纤-石墨烯光波导传播的倏逝场的强度分布和相位均受石墨烯材料作用,石墨烯材料能有效聚集和导行波导中传输的高阶模,在单位传输长度上具有更密集的等相位面. 本文提出了一种利用微纳光纤耦合光倏逝场研究石墨烯相位响应特性的新方法,对基于石墨烯波导的新型调制器、滤波器、激光器和传感器等光子器件的设计和应用具有一定的参考意义. 关键词： 石墨烯平面光波导 倏逝波 光场强度 相位     

基于振动弛豫理论提高光抽运太赫兹激光器输出功率的研究

以半经典密度矩阵理论和分子振动弛豫理论为基础,研究添加适当比例缓冲气体与适当减小波导芯径对光抽运太赫兹激光器输出光强的影响.计算结果表明,加入适当比例缓冲气体或适当减小波导的芯径均能提高太赫兹激光的输出光强;同时优化两个参数能进一步提高抽运激光能量转化为太赫兹激光能量的效率,延长工作腔中的有效激活区,延缓抽运饱和效应的出现,提高太赫兹激光输出光强.该研究对提高光抽运太赫兹激光器的能量转化效率、提高光抽运太赫兹激光器的输出功率及实现光抽运太赫兹激光器的小型化有重要的指导意义.     

Optical cavity coupled surface plasmon resonance sensing for enhanced sensitivity

A surface plasmon resonance (SPR) sensing system based on the optical cavity enhanced detection tech-nique is experimentally demonstrated. A fiber-optic laser cavity is built with a SPR sensor inside. By measuring the laser output power when the cavity is biased near the threshold point, the sensitivity, defined as the dependence of the output optical intensity on the sample variations, can be increased by about one order of magnitude compared to that of the SPR sensor alone under the intensity interrogation scheme. This could facilitate ultra-high sensitivity SPR biosensing applications. Further system miniaturization is possible by using integrated optical components and waveguide SPR sensors.     

Flat-topped beam output from a double-clad rectangular dielectric waveguide laser with a high-index inner cladding

A novel method to produce a flat-topped laser beam by using a double-clad rectangular waveguide laser with high-index inner cladding is presented. The waveguide dispersion equation for cosine mode was deduced, the condition for the flattened mode was given out, relative gains for guided modes were calculated numerically and analyzed. Results indicate that a gain advantage for the flattened mode is clear, a flat-topped laser beam can be achieved when the optical confinement factor, the gain intensity and the output coupler are chosen suitably.     

All optical switching in azo-polymer planar waveguide

In this paper all optical switching in planar methyl red doped poly (methyl methacrylate) (MR/PMMA) waveguide and the effects of different parameters on this process are presented. Switching was achieved by a 488 nm Ar ion laser (pump beam) on a 633 nm He-Ne laser (probe beam) when passed through the waveguide. The effect of temperature and pump intensity, polarization and chopping frequency on switching is investigated. The switching process is attributed to trans-cis-trans photoisomerization of azo dyes in the polymer host. By studying the absorption spectrum of the sample, it is shown that both pump and probe laser beams are effective on the switching process.     

基于平面光波导谐振腔的可调谐光电振荡器

提出了一种基于平面光波导谐振腔的可调谐光电振荡器.该振荡器中,相位调制器串联光波导谐振腔,取代了传统系统中的强度调制器、长光纤和滤波器.由于光学谐振腔对光子频率和相位敏感,调节激光器改变输出光的波长,不仅可以调制光的强度,还可以对微波光子进行选频输出.当光子在波导腔中发生谐振时,产生很强的延时特性,可以取代传统系统中的长光纤.整个光电振荡器系统体积为长29.5cm、宽21cm、高7cm.实验中,改变0.1pm的光子波长,能够产生步长为12.535.5 MHz的调谐,调谐范围达2 GHz,且系统能够产生10 GHz的微波信号,在中心频率为10 GHz处其相位噪声为-109.7dBc/Hz@10kHz.该研究为光电振荡器的小型化和实用化提供了一种新的思路.     

Stressed waveguides with tubular depressed-cladding inscribed in phosphate glasses by femtosecond hollow laser beams

We report on the single-step fabrication of stressed optical waveguides with tubular depressed-refractive-index cladding in phosphate glasses by the use of focused femtosecond hollow laser beams. Tubelike low index regions appear under direct exposure due to material rarefaction following expansion. Strained compacted zones emerged in domains neighboring the tubular track of lower refractive index, and waveguiding occurs mainly within the tube core fabricated by the engineered femtosecond laser beam. The refractive index profile of the optical waveguide was reconstructed from the measured transmitted near-field intensity.     

Bright and dark 40 GHz parabolic pulse generation using a picosecond optical pulse train and an arrayed waveguide grating

We demonstrate parabolic optical pulse generation by manipulating the intensity and phase of individual longitudinal modes of a 40 GHz picosecond optical pulse train in the spectral domain. Bright and dark parabolic pulses were generated from a 40 GHz mode-locked fiber laser using a 64-channel arrayed waveguide grating pulse shaper. The obtained parabolic pulse, which can easily generate a linear chirping, is useful for a number of applications to optical signal processing applications, including pulse compression and time-domain optical Fourier transformation.     

带有多孔二氧化硅间隔层的导模共振光栅实现染料激光器发射增强

导模共振光栅是一种典型的平面波导共振结构,可在光栅表面或波导层内形成较强的局域电场,能增强光与物质的相互作用.本文在导模共振结构的光栅层和基底层之间,引入低折射率的多孔二氧化硅间隔层,显著增强了局域电场与增益介质的接触度.结果表明,引入多孔二氧化硅后,共振产生的电场增强区域上移至激光染料层,增加了激光染料与电场的相互作用,实现了激光出射增强.本文基于时域有限差分法,对结构参数进行分析优化,研究了820 nm共振波长激发下的出射激光特性,得到了连续的激光出射,其能量阈值约为2.5 mJ/cm^2,线宽约为0.3 nm.本文提出的结构实现了对表面局域电场的有效调控,增强了激发光与增益介质的相互作用,不但可应用于激光器,还为其它发光器件的设计提供了参考.     

Compton散射下多信道平面光波导的空间光孤子开关

应用量子微扰理论和多光子非线性Compton散射模型,对Compton散射下多信道平面光波导的空间光孤子开关进行了研究.结果表明:在横向具有正弦形周期折射率调制的非线性平面光波导的多信道系统中,原先束缚在一个信道中的孤子可以靠由入射和散射光形成的耦合控制光点,通过交叉相位调制横向吸引孤子波束,使孤子从原信道切换到邻近信道,从而实现光孤子开关的功能.控制光点可由耦合光在势谷之间的横向聚焦来实现.散射既能使控制光点的有效强度的阈值和孤子的辐射损耗增大,势垒增高,幅度下降较小,有利于孤子开关的形成;又能使波束展宽较宽,并存在开关被破坏的危险.由此可见,Compton散射下恰当控制入射激光强度是实现孤子开关的关键.     

Efficient coupling of a laser to a waveguide using a taper designed by conformal mapping

Maximising the optical power collected in a waveguide from the diffracting field of a semiconductor laser is desirable in optical fibre communication systems. However, the spot size and phase front curvature of the laser field usually makes a poor overlap with the mode of the receiving waveguide. Various proposals have been made to improve this coupling. This paper presents the design of a tapered waveguide section, having the correct geometry and refractive index profile, to efficiently capture and transform the rapidly diffracting light from a semiconductor laser to a planar wavefront in a straight waveguide. Experimentally, such an approach requires the refining of available techniques (UV exposure, ion implantation or diffusion) to obtain the required grading of the refractive index profile within the tapered input section of the receiving waveguide.     

Nanoscopic photodeposited structures analyzed by an evanescent optical method

The evanescent field propagating in waveguides was used to evaluate the profile and growth rate of laser photodeposited a-Se. A pulsed KrF excimer laser was used for deposition. The differential-evanescent light leaking image, was used to analyze the nanostructures in the deposited zones. The relation between the emerging light intensity of the evanescent wave and the optical light intensity propagating in the waveguide was connected to an effective range of the evanescent wave leaking power into the deposited material. The technique provides the nanometric profiles of the ultra-thin photodeposited structures.     

Dispersion modified slot optical waveguides

Advent of slot waveguide structures had opened a new era where light can be confined in low index slot guarded by high index slabs. Already in use SOI slot waveguides (contrast ratio is 2.42) have two distinct properties over the conventional waveguides, i.e. high E-field amplitude, optical power, optical intensity in low index materials, and strong E-field confinement localized to nanometer-size low index regions. We hereby propose a low refractive index contrast ratio slot waveguide structure (ratio is 1.18) comprising of commercially available glass material. Novelty lies in showing high E-field amplitude, optical power, optical intensity, and strong E-field confinement in low index slot regions despite of lowest ever reported contrast ratio. A systematic numerical study on the higher order dispersion characteristics of the widely studied SOI-based slot structure and of our proposed low refractive index contrast slot structure is carried out. It has been demonstrated that low refractive index contrast ratio slot optical waveguide GVD properties are quite different than SOI slot optical waveguide. The less normal dispersion existing in this kind of waveguide could have an impact on their applications in various nonlinear or linear applications.