Application of spatially and temporally apodized non-confocal acoustic transmission microscopy to imaging of directly bonded wafers

Application of a line-shaped point spread function (PSF) to imaging of void defects in directly bonded wafers is considered. Two non-confocally adjusted spherical transducers are employed to implement an acoustic microscope operating in transmission with a time dependent point spread function, whose shape is optimized by both temporal apodization of the received signal and spatial apodization of the transducer aperture. Strong imaging artifacts resulting from the generation and detection of edge waves are eliminated in this way. It is shown by several examples that only a broadband system can be utilized in order to obtain a line-shaped PSF suitable for imaging.     

一维非线性声波传播特性

针对一维非线性声波的传播问题进行了有限元仿真和实验研究. 首先推导了一维非线性声波方程的有限元形式, 含有高阶矩阵的非线性项导致声波具有波形畸变、谐波滋生、基频信号能量向高次谐波传递等非线性特性. 编制有限元程序对一维非线性声波进行了计算并对仿真得到的畸变非线性声波信号进行处理, 分析其传播性质和物理意义. 为验证有限元计算结果, 开展了水中的非线性声波传播的实验研究, 得到了不同输入信号幅度激励下和不同传播距离的畸变非线性声波信号. 然后对基波和二次谐波的传播性质进行详细讨论, 分析了二次谐波幅度与传播距离和输入信号幅度的变化关系及其意义, 拟合出二次谐波幅度随传播距离变化的方程并阐述了拟合方程的物理意义. 结果表明, 数值仿真信号及其频谱均与实验结果有较好的一致性, 证实计算方法和结果的正确性, 并提出了具有一定物理意义的二次谐波随传播距离变化的简单数学关系. 最后还对固体中的非线性声波传播性质进行了初步探讨. 本研究工作可为流体介质中的非线性声传播问题提供理论和实验依据.     

超声检测用压电换能器瞬态特性可控可调

超声检测用压电换能器瞬态特性主要包括瞬态空间响应和瞬态时间响应。本文通过调整控制换能器和激励源,实现瞬态空间响应和瞬态时间响应的某些特性的可控可调。其中包括在空间响应方面消除边缘波以获得平行声束和消除平面波以获得聚焦绳声束;在时间响应方面,调整换能器的背衬阻抗以获得可调首次波幅比和调整换能器结构和激励电信号以获得任意检测信号等。     

Shear horizontal (SH) ultrasound wave propagation around smooth corners

Shear horizontal (SH) ultrasound guided waves are being used in an increasing number of non-destructive testing (NDT) applications. One advantage SH waves have over some wave types, is their ability to propagate around curved surfaces with little energy loss; to understand the geometries around which they could propagate, the wave reflection must be quantified. A 0.83 mm thick aluminium sheet was placed in a bending machine, and a shallow bend was introduced. Periodically-poled magnet (PPM) electromagnetic acoustic transducers (EMATs), for emission and reception of SH waves, were placed on the same side of the bend, so that reflected waves were received. Additional bending of the sheet demonstrated a clear relationship between bend angles and the reflected signal. Models suggest that the reflection is a linear superposition of the reflections from each bend segment, such that sharp turns lead to a larger peak-to-peak amplitude, in part due to increased phase coherence.     

一种用于变压器局部放电在线监测的光纤声发射传感器实验研究

提出了一种光纤声发射传感器并构建传感系统实现变压器局部放电在线监测,利用传感光栅体积小,重量轻,灵敏度高和抗电磁干扰的特点,将传感器置于变压器内部实现局部放电声发射信号的测量。研究了传感光栅实现声发射应力波测量的机理,声发射信号引起传感光栅反射光谱发生漂移,导致特定频点处反射光强发生变化,通过反射光强的变化实现声发射信号的测量。构建声发射传感系统实验模型并提出了一种系统性能优化策略,使系统工作在传感光栅反射光谱上升或下降沿的半峰值频点处,从而保障传感系统具有良好的线性输出特性;研究传感系统工作点稳定技术,设计信号反馈回路自动跟踪反射光谱的漂移,保证系统稳定工作在传感光栅半峰值频点处,消除温度变化对传感系统测量精度的影响。将封装好的传感器用于变压器局部放电现场检测,结果表明,光纤光栅声发射传感器与压电传感器相比具有灵敏度高、动态范围宽等优点,可以实现变压器局部放电在线监测。     

Nonlinear modulation technique for NDE with air-coupled ultrasound

The present study is aimed at expanding flexibility and application area of nonlinear acoustic modulation (NAM-) technique by combining the benefits of noncontact ultrasound excitation (remote locating and imaging of defects) with sensitivity of nonlinear methods in a new air-coupled NAM-version. A pair of focused air-coupled transducers was used to generate and receive (high-frequency) longitudinal or flexural waves in plate-like samples. Low-frequency (LF-) vibrations were excited with a shaker or a loudspeaker. Temporal and spectral analysis of the output signal revealed an extremely efficient nonlinear amplitude modulation and multiple frequency side-bands for sound transmission and flexural wave propagation through cracked defects. On the contrary, a negligible modulation was observed for large and medium scale inclusions and material inhomogeneities (linear defects). A new subharmonic mode of the NAM was observed at high excitation levels. It was also shown for the first time that nonlinear vibrations of cracks resulted in radiation of a very high-order harmonics (well above 100) of the driving excitation in air that enabled imaging of cracks remotely by registration their highly nonlinear "acoustic emission" with air-coupled transducers.     

Measuring technique for static electricity using focused sound

A novel method is proposed for non-contact measurement of the distribution of electrostatic charge on a surface based on scanning the sample surface with a focused high frequency acoustic beam to excite movement of the sample surface. An electric field is induced by exciting a charged film-like object, and an electric field sensor measures it instead of an electrostatic field. The focused ultrasound waves are generated by controlling individually the phase of each 285 airborne ultrasound transducers.     

基于群速度失配的超声兰姆波二次谐波的时域测量方法

考虑到发射和接收换能器对超声兰姆波时域二次谐波信号所带来的不可避免的影响,提出一种基于基频与二倍频兰姆波群速度失配的超声兰姆波二次谐波的时域测量方法。当基频与二倍频超声兰姆波的相速度匹配而群速度失配时,在超声兰姆波传播过程中所发生的二次谐波信号,在时域上可与源于斜劈换能器的二次谐波信号相分离。采用仅源自于基频兰姆波的时域二次谐波的积分振幅,定量描述兰姆波二次谐波的发生效率。以铝板中传播的兰姆波为例,给出了时域二次谐波的具体测量过程。本文提出的测量方法放宽了超声兰姆波二次谐波的测量条件,且扣除了换能器对二次谐波信号所带来的影响,所测得的二次谐波信号完全来自于基频兰姆波时域信号的二次谐波发生效应。      

Ultrasound fields in attenuating media

For medical ultrasonic imaging and for nondestructive testing, the attenuation of pressure waves and the resulting shift in wave velocity are important features in commonly used transmission media such as biological tissue. An algorithm for the numerical evaluation of pressure field distributions generated by ultrasonic transducers is presented. The attenuation and dispersion of the sound transmission medium are taken into consideration. The sound fields are computed numerically for continuous wave as well as pulse excitation. The transducer has plane or gently curved geometry and is embedded in a plane rigid baffle. The numerically determined pressure fields are presented as 3D plots, as gray-scale images for a fixed time stamp (like a snapshot), or as isobars regarding the maximum values over time for each local point in the area under investigation. The algorithm described here can be utilized as a tool for design of ultrasound transducers, especially array antennas.     

Wideband chaotic oscillation in a self-oscillatory system with a nonlinear transmission line on magnetostatic waves

Wideband chaotic microwave oscillation in a ring self-oscillatory system is studied. The system includes a solid-state power amplifier and a wideband nonlinear transmission line with a ferromagnetic film in which magnetostatic waves of different types are excited. It is found that the eigenmodes of the self-oscillatory system excited in the passband of the transmission line on magnetostatic waves become noisy because of spin wave parametric excitation due to the magnetostatic wave and nonlinearity of the power amplifier. A continuous spectrum of modes observed in the wideband chaotic signal is associated with the presence of a descending portion in the dynamic characteristic of the nonlinear transmission line, which arises when a magnetostatic surface wave is excited.     

Effects of size and arrangement of virtual transducer on photoacoustic tomography

In this paper, we investigate the effects of the relative size and arrangement of a virtual transducer on the image quality in limited-view photoacoustic tomography. A virtual transducer refers to the acoustic scatterers used to reflect photoacoustic waves and improve the images reconstructed from incomplete PA signal. Size and spatial arrangement determine the performance of the virtual transducer. In this study, the scatterers utilized as virtual transducers are arranged in different manners, such as on a straight line or on an arc line. We find that virtual transducers with a big distributing angle can provide more significant image improvement than with a small distributing angle, which is similar to the true transducers. We also change the size of virtual transducer and study its influence on image quality. It is found that the bigger scatterers provide better images than the smaller ones. Especially, when the size of scatterers is reduced to the wavelength of photoacoustic wave, the image quality observably decreases, owing to the strong diffraction effect. Thus, it is suggested that the size of the acoustical scatterers should be much larger than the photoacoustic wavelength. The simulations are conducted, and the results could be helpful for the application and further study of virtual transducer theory in limited-view photoacoustic tomography.     

Using streamlines to visualize acoustic energy flow across boundaries

For spherical waves that radiate from a point source in a homogeneous fluid and propagate across a plane boundary into a dissimilar homogeneous fluid, the acoustic field may differ significantly from the geometric acoustic approximation if either the source or receiver is near the interface (in acoustic wavelengths) or if the stationary phase path is near the critical angle. In such cases, the entire acoustic field must be considered, including inhomogeneous waves associated with diffraction (i.e., those components that vanish with increasing frequency). The energy flow from a continuous-wave monopole point source across the boundary is visualized by tracing acoustic streamlines: those curves whose tangent at every point is parallel to the local acoustic intensity vector, averaged over a wave cycle. It is seen that the acoustic energy flow is not always in line with the "Snell's law" or stationary phase path. Also, plots of acoustic energy streamlines do not display unusual behavior in the vicinity of the critical angle. Finally, it is shown that there exists a law of refraction of acoustic energy streamlines at boundaries with density discontinuities analogous to Snell's law of refraction of ray paths across sound speed discontinuities. Examples include water-to-seabed transmission and water-to-air transmission.     

Theoretical analysis of an ultrasonic interferometer for precise measurements at high pressures

Expressions making it possible to calculate the transmission coefficient of an ultrasonic interferometer, its Q factor and errors of interferometric measurements are presented. These expressions are obtained on the basis of a one-dimensional model which takes into account the non-ideal reflection of acoustic waves from the transducers, diffraction losses and electromechanical properties of transducers. Fixed path ultrasonic interferometers which are widely used for high precision measurements of ultrasound absorption and velocity in liquids, include air-backed transducers. Air-backing limits the application of these interferometers for the measurements under the high pressures. The influence of non-gaseous backing of transducers on the characteristics of an interferometer is theoretically analysed by means of suggested expressions. Frequency dependences of main parameters of the interferometer are obtained. The possibility of high precision measurements of velocity and absorption of ultrasound in liquids under the high pressures by means of fixed path interferometers with liquid-backed transducers is shown.     

Backscattering enhancements from Rayleigh waves on the flat face of a tilted solid cylinder in water

When the face of a finite solid elastic cylinder is ensonified by an acoustic wave, a variety of backscattering contributions associated with acoustic wave coupling into elastic waves are observed. A significant backscattering enhancement is observed for tilts such that the acoustic wave is incident on the face of the cylinder in the vicinity of the coupling angle for launching Rayleigh waves across the face. The observed backscattering indicates that the Rayleigh waves are reflected at the edge of the face and subsequently radiate acoustic waves in the backscattering direction. The measured backscattering is compared to an approximate theoretical prediction. Approximating the focusing of the Rayleigh wave after reflection at the (circular) edge by a Gaussian beam pressure distribution on the cylinder's face yields simple expressions for the amplitude which are consistent with the measurements. In the vicinity of end-on incidence, other backscattering contributions due to the reflection of waves traveling down the length of the cylinder are observed. There is also evidence of a face-traversing longitudinal wave for slightly tilted cylinders.     

基于Rayleigh-Bloch模式的单层结构弯曲声波导

基于一维声栅中的Rayleigh-Bloch(RB)模式基本特点,设计了一种单层结构弯曲声波导.利用有限元方法从时域和频域两方面验证了弯曲声波导的有效性,RB模式波可以沿着波导的弯曲界面传播.研究发现,由于采用了环形结构基本单元,在该波导中存在两种传播模式,分别对应能量局域在单元间(模式-1)和单元内部(模式-2)两种情况.其中,模式-2声传输效果更佳,几乎可实现无损传输.时域研究中分别采用了调制脉冲和高斯脉冲两种信号形式,分析了它们在弯曲声波导中的传输过程.由于波导中只允许RB模式波传播,因此对于宽频信号来说,可起到滤波的效果.并且,不同模式(频率)的信号会出现在声波导的不同位置,所得结果对于声波定向传输、声探测与识别等研究具有理论与应用价值.     

Propagation of terahertz waves in a dust acoustic wave

The propagation of terahertz waves in a dust acoustic wave is investigated numerically. By assuming a sinus profile of the dust number density in the dust acoustic waves, the transmission properties are calculated using finite difference time domain method. It shows that the dust acoustic wave can function similarly as a Bragg filter to block the terahertz waves of a certain wavelength. The bandwidth of the filter depends on the density profile of the dust acoustic wave.     

Surface acoustic waves in an elastic wedge media

We consider surface acoustic waves in an elastic wedge media. It is established that the investigated waves substantially differ from known ones. For example, the movement of surface Rayleigh wave in the direction to the edge leads to a change of its structure, accompanied by the splitting of the initial wave to two separate modes and radiation of shift and longitudinal waves. Along the edge of the wedge the surface wave is strongly localized in the transverse direction. Are discussed the properties of the wedge antisymmetric normal waves, propagating parallel to the edge of the wedge.     

南海北部海域内波环境下声传播损失起伏统计特性

浅海内波会引起声传播能量随时间的起伏变化,进而影响水声设备的工作性能.本文利用2015年南海北部一次浅海声场起伏实验数据,对比分析了浅海线性内波和孤立子内波条件下的声传播损失统计特性.在孤立子内波条件下,声传播损失起伏明显加剧,可达11 dB,且分布明显展宽,相对于线性内波的环境,声传播损失起伏可增加5 dB.从简正波...     

Pulsed Sounding of Cracks with the Use of the Modulation of Ultrasound by Vibrations

The possibility of using the effect of the modulation of ultrasound by vibrations due to the presence of cracks for the nonlinear acoustic detection of cracks is demonstrated. The method is based on a pulsed ultrasonic sounding with gating the received signal and simultaneously exciting low-frequency vibrations in the sample. The presence of a crack is characterized by the modulation of the ultrasonic wave reflected from the crack. The visualization of the crack position in a model object (a metal rod) is performed. The possibility of selecting a crack on the background of an intense signal reflected from a cavity is experimentally demonstrated. The manifestation of the nonlinear properties of a crack is studied as a function of the polarization of the flexural vibrations of the rod.     

Theoretical Analysis of Shear Wave Interference Patterns by Means of Dynamic Acoustic Radiation Forces

Acoustic radiation forces associated with high intensity focused ultrasound stimulate shear wave propagation allowing shear wave speed and shear viscosity estimation of tissue structures. As wave speeds are meters per second, real time displacement tracking over an extend field-of-view using ultrasound is problematic due to very high frame rate requirements. However, two spatially separated dynamic external sources can stimulate shear wave motion leading to shear wave interference patterns. Advantages are shear waves can be imaged at lower frame rates and local interference pattern spatial properties reflect tissue's viscoelastic properties. Here a theoretical analysis of shear wave interference patterns by means of dynamic acoustic radiation forces is detailed. Using a viscoelastic Green's function analysis, tissue motion due to a pair of focused ultrasound beams and associated radiation forces are presented. Overall, this paper theoretically demonstrates shear wave interference patterns can be stimulated using dynamic acoustic radiation forces and tracked using conventional ultrasound imaging.