Poly ∶ DCJTB 为功能层LEC器件的能量传递

在有机发光器件中,掺杂染料分子是改变发光颜色,提高发光性能的有利手段。在掺杂体系中,主体材料向掺杂剂的能量传递是主要的激发态弛豫过程。在LEC器件中,利用掺杂手段改变发光颜色的方法报道很少。研究了以发射绿光(峰值550 nm)的共聚物Poly 中掺杂DCJTB作为功能层的LEC器件的发光特性。器件的结构为ITO/Poly ∶ DCJTB+PEO+LiCF₃SO₃/Al。共聚物的光致发光光谱几乎覆盖了整个DCJTB吸收光谱的范围,满足能量传递的要求。通过光致发光与电致发光光谱的研究,发现掺杂后的薄膜不论是光致发光还是电致发光,都以DCJTB的发射为主,说明二者之间的确存在能量传递。     

掺杂DCJTB聚合物电化学池（LEC）的发光性质

通过在聚合物电化学池(LEC)发光器件的发光材料MEH-PPV中掺杂红光染料DCJTB,对LEC器件的发光性质进行研究。基于器件结构为ITO/MEH-PPV PEO LiCF3SO3/Al的薄膜LEC器件,其电致发光峰在570nm左右,通过在MEH-PPV与PEO的混合膜中掺杂不同比例的红光染料DCJTB,随着掺杂比例的增加,器件的发光峰由570nm向红光波段移动,通过控制DCJTB的掺杂比例制备了发光峰在570~650nm连续变化的LEC电致发光器件。对其分析认为从LEC主体发光聚合物MEH-PPV到染料DCJTB间发生了良好的能量传递。     

以蓝色发光材料DPVBi为基质的白色发光器件

白色有机发光器件是实现彩色平板显示的重要方案之一。利用蓝色发光材料DPVBi[4，4′—(2，2—苯乙烯基)—1，1′—联苯]掺杂红光染料DCJTB[4—氰甲烯基—2—叔丁基—6—(1，1，7，7—四甲基久洛尼定基—9—烯炔基—4H—吡喃)]作发光层制备了白色发光器件。研究了DPVBi掺杂不同浓度IDCJTB薄膜的光致发光性质，根据光致发光结果，制备了以DPVBi掺杂不同浓度DCJTB作发光层的电致发光器件，其结构为ITO／GuPc／NPB／DPVBi：DCJTB／Alq3／LiF／Al。当DCJTB质量分数为0．0008时，器件实现了白色发光(色度x=0．25，y=0．32)，电致发光和光致发光的掺杂比例基本相符，表明器件的白色发光主要是由基质DPVBi向掺杂剂DCJTB的能量传递产生的。研究还发现：白色器件随电压升高，光谱中蓝色成分相对于红色成分的比例略有增加，文章对此现象进行了分析。该白光器件在14V时达到最高亮度7822cd／cm^2，在20mA／cm^2电流密度下的亮度为-489cd／cm^2，最大流明效率为1．75lm／W。     

利用级联式能量传递的有机电致发光器件

为了提高掺杂型有机电致发光器件(OLED)中主体发光材料与客体荧光染料间能量传递的效率,2-对联苯-8-羟基喹啉锌(Zn ₂)作为NPB : DCJTB掺杂体系的能量助传递剂,制备了结构如:ITO/NPB/NPB : DCJTB/Zn ₂/BCP/Al的有机电致发光器件。助传递剂Zn ₂的加入,能够两次利用Frster能量转移,实现NPB向DCJTB级联式的能量传递过程,提高低浓度时掺杂染料DCJTB红光发射的纯度;此外,还探讨了三者间能量传递的有效距离,即当助传递剂与掺杂体系的距离在小于10 nm的范围内,其参与能量传递的效率随着距离的增加而逐渐下降。     

掺杂DCJTB聚乙烯咔唑的发光性质

研究了PVK∶DCJTB体系的发光特性。实验结果表明,PVK∶DCJTB薄膜光激发时,PVK和DCJTB之间存在能量传递,DCJTB的浓度从1%增加到2%,能量传递效率明显增强,但仍然不充分。引入Alq3层后的PVK∶DCJTB/Alq3双层薄膜,PVK的发光被有效地抑制了,Alq3明显促进了PVK向DCJTB的能量传递效率,说明Alq3起到了能量传递的"桥梁"作用。而结构为ITO/PVK∶DCJTB/Alq3/LiF(1nm)/Al的器件的电致发光光谱与光致发光光谱明显不同。电致发光时,Alq3层的发光的相对强度比光致发光时大许多,而且发光强度随着驱动电压的增加而增强,说明随电压的增加,有更多的空穴注入到Alq3层,致使载流子在Alq3层的复合几率随电场的增强而增大。     

两种铽配合物与PVK混合体系的发光机理研究

研究了稀土配合物Tb(p-MBA)₃phen(样品Ⅰ)和Tb(p-ClBA)₃phen(样品Ⅱ)与导电聚合物材料PVK掺杂体系的光致发光和电致发光特性。发现在样品Ⅰ与PVK混合薄膜的光致发光中,除了三价铽离子的发光外,还能看到明显的PVK的发光;而在电致发光中,PVK的发光完全被抑制,只能看到Tb3+的绿光发射。对样品Ⅱ与PVK的混合发光层,无论其光致发光谱还是电致发光谱,都没有看到410 nm处PVK的发射。进一步测量两种材料的激发光谱,初步探讨了器件的发光机理。样品Ⅰ的发光可能来源于两个方面,一是PVK到稀土配合物的不完全的能量传递,二是由于载流子俘获机理;样品Ⅱ的发光则是由于PVK到稀土配合物的完全的能量传递。     

掺杂不同一维纳米材料的空穴缓冲层对有机电致发光器件性能的影响

对一维纳米材料在空穴缓冲层PEDOT中的作用进行了研究。光致发光表明在PEDOT中掺杂一维纳米材料(二氧化钛纳米管和氧化锌纳米棒)可以提高双层样品PEDOT/MEH-PPV的发光效率。拉曼光谱的结果说明正是由于一维纳米材料与PEDOT之间存在的强相互作用,才减少了PEDOT/MEH-PPV界面上猝灭发光的缺陷态的产生。在以MEH-PPV作为发光层的聚合物电致发光器件中,在PEDOT中掺杂二氧化钛纳米管和氧化锌纳米棒后,器件的最大效率分别提高了2倍和2.5倍。     

基于量子点和MEH-PPV的白光发光二极管的研究

利用无机纳米材料与有机聚合物材料相结合的方法制备白光发光二极管器件, 研究了蓝光量子点QDs(B)掺杂聚[2-甲氧基-5-(2-乙基己氧基-1, 4-苯撑乙烯撑](MEH-PPV) 复合体系的发光特性及量子点QDs(B) 掺杂浓度(质量分数)不同对器件发光特性的影响. 制备了ITO/PEDOT:PSS/MEH-PPV:QDs(B)/LiF/Al 结构的电致发光器件, 测试了器件的电致发光光谱和电学、光学特性. 当QDs掺杂浓度为40%, 驱动电压为8 V时器件能得到较为理想的白光发射. 同时, 对比研究了非掺杂体系的发光特性, 制备了结构为ITO/PEDOT:PSS/MEH-PPV/QDs(B)/LiF/Al的器件, 掺杂体系相较于非掺杂体系, 器件的最大亮度增大, 启亮电压降低, 并分析了掺杂体系器件性能改善的原因.     

基于MEH-PPV/ZnSe纳米复合器件的电致发光特性的研究

以巯基乙酸作为稳定剂在水相中制备了ZnSe纳米晶,用X射线粉末衍射(XRD)和X射线光电子能谱(XPS)对其进行了表征。用表面活性剂将ZnSe纳米晶从水相中转移到有机相中,使其与聚合物MEH-PPV复合作为发光层,制备了多层电致发光器件Glass/ITO/MEH-PPV∶ZnSe/BCP/Alq₃。对ZnSe纳米晶和MEH-PPV薄膜的光致发光谱及其吸收光谱的比较表明ZnSe纳米晶和MEH-PPV之间存在着能量传递,这是导致纳米复合薄膜的光致发光光谱和电致发光光谱存在差异的原因之一。文章对其在光激发和载流子注入条件下的不同发光机制进行了讨论。通过对器件的光电特性进行研究,发现ZnSe纳米晶发光的比例随着外加电压的增加而增加,而且器件的I-V特性基本上符合二极管的特性。     

荧光染料超薄层对有机电致发光器件发光光谱的影响

采用在主体材料上蒸镀一层超薄层的方法,研究了三种有机小分子荧光染料dimethylquinacridon(DMQA)、4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethy ljulolidyl-9-enyl)-4-pyran(DCJTB)和5,6,11,12-tetraphenylnaphthacene(Rubrene)的浓度效应对有机电致发光器件(OLED)电致发光光谱的影响。结果表明,与常规掺杂器件相比,染料超薄层器件的光谱中出现了微弱的主体材料的发光峰,浓度猝灭现象更为明显。三种染料的浓度猝灭程度从高到低依次为DMQA、DCJTB和Rubrene。同时,我们使用此三种染料配制了溶液,测试了它们在不同浓度下的光致发光光谱强度,进一步探讨了掺杂剂浓度猝灭强弱与器件的发光光谱特性的关系。     

Radionuclides in deposition in the Ignalina NPP region in 2005

Results of radionuclide activity concentration measurements in deposition and ground-level air conducted at the station of the Institute of Physics situated 3.5 km from the Ignalina Nuclear Power Plant (Ignalina NPP) in 2005 are analyzed. Atmospheric depositional fluxes of ⁷Be, ⁶⁰Co and ¹³⁷Cs are estimated. Radionuclide particle deposition rates are calculated. The Hybrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT) model of the global dispersion and deposition is used to explain variations in the ¹³⁷Cs activity concentration in the ground-level air in the Ignalina NPP region in 2005. An increase in the ¹³⁷Cs activity concentration of up to 17.4 μBq m⁻³ on 30 October-5 November is studied. Modelling results show that the Chernobyl NPP Unit 4 Sarcophagus and the radiocaesium resuspension from the Chernobyl NPP accident polluted regions are sources of ¹³⁷Cs to the environment of the Ignalina NPP. Results on solubility in water of aerosols — carriers of ¹³⁷Cs — are discussed.     

Universal scaling in BCS superconductivity in three dimensions in non-s waves

The solutions of a renormalized BCS equation are studied in three space dimensions in s, p and d waves for finite-range separable potentials in the weak to medium coupling region. In the weak-coupling limit, the present BCS model yields a small coherence length and a large critical temperature, , appropriate for some high- materials. The BCS gap, , and specific heat as a function of zero-temperature condensation energy are found to exhibit potential-independent universal scalings. The entropy, specific heat, spin susceptibility and penetration depth as a function of temperature exhibit universal scaling below in p and d waves. Received: 18 July 1997 / Revised: 8 September 1997 / Accepted: 29 September 1997     

Thermal convection in Rivlin-Ericksen elastico-viscous fluid in porous medium in hydromagnetics

The thermal instability of a layer of Rivlin-Ericksen elastico-viscous fluid in porous medium acted on by a uniform magnetic field is considered. For stationary convection, Rivlin-Ericksen elastico-viscous fluid behaves like a Newtonian fluid. The magnetic field is found to have stabilizing effect whereas medium permeability has destabilizing effect. The magnetic field introduces oscillatory modes in the system, A sufficient condition for the non-existence of overstability is also obtained.     

Supergravity in theory in 11 dimensions

We present the action and transformation laws of supergravity in 11 dimensions which is expected to be closely related to the O(8) theory in 4 dimensions after dimensional reduction.     

Uncertainty in prediction and in inference

The concepts of uncertainty in prediction and inference are introduced and illustrated using the diffraction of light as an example. The close relationship between the concepts of uncertainty in inference and resolving power is noted. A general quantitative measure of uncertainty in inference can be obtained by means of the so-called statistical distance between probability distributions. When applied to quantum mechanics, this distance leads to a measure of the distinguishability of quantum states, which essentially is the absolute value of the matrix element between the states. The importance of this result to the quantum mechanical uncertainty principle is noted. The second part of the paper provides a derivation of the statistical distance on the basis of the so-called method of support.     

Fano-type features in magnetoabsorption in semiconductors

It is shown that bulk semiconductors exhibit strongly asymmetric Fano-type resonance profiles in magnetoabsorption processes involving the formation of hot electron-hole pairs (EHPs) and accompanied by the scattering of the EHPs by defects. This result is valid for transitions to electronic states with large Landau quantum numbers, when the Coulomb interaction plays a small role. The physical reason for such a sharp change in the magnetoabsorption coefficient as compared with the expected result for the ordinary density of states in a quantizing magnetic field is that the electronic excitations are quasi-one-dimensional. The form of the resonance absorption is in good qualitative agreement with the experimental data. Pis’ma Zh. éksp. Teor. Fiz. 63, No. 8, 619–622 (25 April 1996)     

Scale-free phenomenon in industries in China

In this paper, we investigate the data of industries in China and find that the frequency distributions of fixed assets and fixed-assets’ investment of industries obey power laws. We show that these power-law modes can be explained by the rules of the Simon Model, rather than the existing investment theories such as the classical investment theory or acceleration principle. Moreover, the mechanism of the investment distribution may be similar to the forest-fire model of self-organizing criticality. By introducing the complex system methods, this research changes the traditional opinion of the investment and gains some meaningful understanding in the dynamics of industries and the economic cycle.