Electrochemical performances of a novel lithium bis(oxalate)borate-based electrolyte for lithium-ion batteries with LiFePO4 cathodes

Lithium bis(oxalate)borate (LiBOB) is a promising salt for lithium-ion batteries. However, it is necessary to exert the electrochemical performance of LiBOB by the appropriate solvent. With dimethyl sulfite (DMS) as mixed solvents, the electrochemical behavior of γ-butyrolactone (GBL) with LiBOB is studied in this paper. It shows that LiBOB-GBL/DMS electrolyte has high oxidation potential (>5.3 V) and satisfactory conductivities. When used in lithium and mesophase carbon microbead cells, the novel electrolyte exhibits not only excellent film-forming characteristics but also low impedances of the interface films. Besides, when used in LiFeO₄/Li cells, compared to the cell with the electrolyte system of 1 mol L^?1 LiPF₆–ethylene carbonate (EC)/dimethyl carbonate (DMC) (1:1, v/v), LiBOB-based electrolyte exhibits several advantages, such as more stable cycle performance at room temperature and higher mean voltage.     

Preparation and performance of the polyethylene-supported polyvinylidene fluoride/cellulose acetate butyrate/nano-SiO<Subscript>2</Subscript> particles blended gel polymer electrolyte

The preparation of polyethylene-supported poly(vinylidene fluoride)/cellulose acetate butyrate/nano-SiO₂ particle (PVDF-CAB-SiO₂/PE) blended gel polymer electrolytes (GPEs) is reported here. The electrolyte uptake, mechanical properties, thermal stability, and electrochemical performance of these electrolytes are characterized to evaluate their potential application in lithium-ion batteries (LIBs). The results indicate that the particle size of SiO₂ can be adjusted by the tetraethyl orthosilicate (TEOS) concentration and affects the physicochemical properties of the membrane. By doping 5 wt.% SiO₂ (500 nm) into the PVdF-CAB blended polymer, the porosity of the membrane increases from 40 to 42.3 %, the mechanical strength from 117.3 to 138.7 MPa, the electrolyte uptake from 149 to 195 %, the oxidation decomposition potential from 4.7 to 5.2 V, and the ionic conductivity of the corresponding GPE is improved from 1.16 to 2.98 mS cm^?1 at ambient temperature. The PVDF-CAB-SiO₂/PE-based GPE and the two electrodes are suitably compatible, and the thermal stability is higher than that of the polyethylene (PE) membrane. The LIBs with the as-prepared GPE also exhibit enhanced discharge capacity and cycle stability, indicating the promising application of these GPEs in LIBs.     

Effect of sulfolane and lithium bis(oxalato)borate-based electrolytes on the performance of spinel LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathodes at 55 °C

To seek a promising candidate electrolyte at elevated temperature for lithium manganese oxide (LiMn₂O₄)/Li cells, the electrochemical performance of 0.7 mol L^?1 LiBOB (lithium bis(oxalate)borate)-SL (sulfolane)/DEC (diethyl carbonate) (1:1, in volume) electrolyte was studied at 55 °C. The Mn dissolution in electrolyte was analyzed by inductively coupled plasma (ICP) analysis. AC impedance measurement and scanning electron microscopy (SEM) analysis were used to analyze the formation of the surface film on the LiMn₂O₄ electrode. The results demonstrate that the LiBOB-SL/DEC electrolyte can slow down the dissolution and erosion of Mn ions, and decrease the interface impedance. Moreover, the LiBOB-SL/DEC electrolyte could obviously improve the capacity retention, the operating voltage (4.05 V), and the rate performance of LiMn₂O₄/Li cells.     

Preparation,properties, and Li-ion battery application of EC + PC-modified PVdF-HFP gel polymer electrolyte films

Based on poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) and lithium tetrafluoroborate (LiBF₄) salt along with blending plasticizers, ethylene carbonate (EC) and propylene carbonate (PC), high Li-ion-conducting gel polymer electrolyte films are developed. Their properties are characterized by various techniques. The ambient temperature ionic conductivity of the 85PVdF-HFP:15LiBF₄ + 150(EC + PC) electrolyte film has a high value of 8.1 × 10^?4 S cm^?1. Its crystallinity, melting point, and electrochemical stability window are 9.5%, 115 °C, and 4.6 V, respectively. The mechanical testing shows that the Young’s modulus, yield strength, and breaking strain of this electrolyte film are 36.8 MPa, 3.4 MPa, and 320%, respectively. Lithium-ion batteries based on the gel polymer electrolyte film exhibit remarkable charge–discharge and cycling performances. The initial discharge capacity of this battery is as high as 165.1 mAh g^?1 at 0.1 C and just shows a small capacity fading of 4.8% after 120 cycles, indicating that the 85PVdF-HFP:15LiBF₄ + 150(EC + PC) system is an excellent electrolyte candidate for lithium-ion battery applications. The charge–discharge performance of the Li-ion cell fabricated with this gel polymer electrolyte film is apparently better than that of the previously reported Li-ion cells fabricated with other PVdF-HFP-based gel polymer electrolyte films.     

Triethylbutylammonium bis(trifluoromethanesulphonyl)imide ionic liquid as an effective electrolyte additive for Li-ion batteries

Ionic liquids are promising additives for Li-ion batteries owing to its desirable physicochemical properties. Triethylbutylammonium bis(trifluoromethanesulphonyl)imide ([N₂₂₂₄][Tf₂N]) ionic liquid was synthesized and their physical and electrochemical properties were investigated. Among several quaternary ammonium ionic liquids, [N₂₂₂₄][Tf₂N] exhibited higher conductivity (1.31 mS?cm^?1), better thermal and electrochemical stabilities, and wide electrochemical window, i.e., more than 5.9 V. Standard solution was prepared by dissolving lithium bis(trifluoromethanesulphonyl)imide (LiTf₂N) in ethylene carbonates/dimethyl carbonate (1:1, by weight). The conductivity for the electrolyte containing [N₂₂₂₄][Tf₂N] and the mixed electrolyte without additives at 25 °C are 10.24 and 8.79 mS?cm^?1, respectively. LiFePO₄ half-cell containing 0.6 mol?L^?1 LiTf₂N-based organic electrolyte with [N₂₂₂₄][Tf₂N] showed relatively high initial discharge capacity and coulombic efficiency at first cycle. It is found that the mix [N₂₂₂₄][Tf₂N] electrolyte exhibits relatively high-rate capacity. The capacity retention of half-cell containing [N₂₂₂₄][Tf₂N] is 2 % more than without additive at 0.2 C. However, the rate capacity retention of the half-cell with mix [N₂₂₂₄][Tf₂N] electrolyte is above 10 % more than without additive at 0.5 C. The results showed that [N₂₂₂₄][Tf₂N] was an effective electrolyte additive in LiFePO₄ half-cell.     

Effect of different compositions of ethylene carbonate and propylene carbonate containing iodide/triiodide redox electrolyte on the photovoltaic performance of DSSC

The effect of different compositions (in weight percent) of ethylene carbonate (EC) and propylene carbonate (PC) containing iodide/triiodide redox electrolyte on the photoelectrochemical performance of N719-sensitized nanocrystalline TiO₂ solar cell was studied. The cells consisted of 0.6 M 1-hexyl-2,3-dimethylimidazolium iodide, 0.1 M LiI, 0.05 M I₂ and 0.5 M 4-tert-butylpyridine in different compositions such as 1:1, 1:2, and 2:1 wt% of EC and PC. In 1:1 wt% of EC and PC containing redox electrolyte, short circuit photocurrent density (J _sc) increased and open circuit voltage (V _oc) decreased. But in 1:2 and 2:1 wt% of EC and PC containing redox electrolytes, V _oc increased and J _sc decreased but fill factor remained relatively constant. Dye-sensitized solar cells (DSSCs) prepared using these electrolytes give a short circuit photocurrent densities of 16.86, 12.71, and 12.09 mA/cm²; an open circuit voltages of 0.73, 0.78, and 0.79 V; fill factors of 0.63, 0.64, and 0.64; and an overall conversion efficiencies of 7.76, 6.34, and 6.13 % at an incident light of 100 mWcm^?2 for 1:1, 2:1, and 1:2 wt% of EC/PC containing redox electrolytes, respectively. The incident photon-to-current conversion efficiency was higher in the case of 1:1 wt% of EC and PC containing redox electrolyte than 1:2 and 2:1 wt% of EC and PC containing redox electrolyte. It revealed that 1:1 wt% of EC and PC containing iodide/triiodide redox electrolyte is an effective electrolyte system for the fabrication of long-term stable DSSC.     

Effect of sodium salts on the cycling performance of tin anode in sodium ion batteries

To determine the effect of electrolyte salts on the cycling properties of tin anodes in sodium ion batteries, sodium/tin cells were prepared using eight electrolytes containing NaCF₃SO₃, NaBF₄, NaClO₄, and NaPF₆ in ethylene carbonate-dimethyl carbonate (EC-DMC) and EC-DMC/fluoroethylene carbonate (FEC) solvents. The first charge capacity and cycling properties strongly depended on the electrolyte salts. Additionally, an appropriately chosen electrolyte salt in combination with the FEC additive improved the cycling properties of the tin electrode. The tin electrode in the presence of the FEC-containing NaPF₆-based electrolyte exhibited the best cycling properties. The first charge capacity and charge capacity after the 45th cycle were 220 and 189 mAh g^?1 _electrode, respectively at a current density of 84.7 mA g^?1 _electrode. The rate performance is also studied using the optimized electrolyte which reveals the ability of the electrode to perform in high current application. At a high current density of 4235 mA g^?1 _electrode, the capacity delivered is 24 mAh g^?1 _electrode. At a current rate of 1694 mA g^?1 _electrode, at the end of 1400th cycle, capacity is about 45 mAh g^?1 _electrode. The results of the study clearly indicate that the electrolyte salts critically affect the electrochemical performance of the tin anode in sodium ion batteries.     

The physical and electrochemical properties of poly(vinylidene chloride-co-acrylonitrile)-based polymer electrolytes prepared with different plasticizers

Lithium ion-conducting membranes with poly(ethylene oxide) (PEO)/poly(vinylidene chloride-co-acrylonitrile) (PVdC-co-AN)/lithium perchlorate (LiClO₄) were prepared by solution casting method. Different plasticizers ethylene carbonate (EC), propylene carbonate (PC), gamma butyrolactone (gBL), diethyl carbonate (DEC), dimethyl carbonate (DMC), and dibutyl phthalate (DBP) were complexed with the fixed ratio of PEO/PVdC-co-AN/LiClO₄. The preparation and physical and electrochemical properties of the gel polymer electrolytes have been briefly elucidated in this paper. The maximum ionic conductivity value computed from the ac impedance spectroscopy is found to be 3?×?10^?4 S cm^?1 for the EC-based system. From DBP-based system down to EC-based system, a decrease of crystallinity and an increase of amorphousity are depicted by X-ray diffraction technique, the decrease of band gap energy is picturized through UV–visible analysis, the decrease of glass transition temperature is perceived from differential scanning calorimetry plots, and the reduction of photoluminescence intensity is described through photoluminescence spectroscopy study at an excitation wavelength of 280 nm. Atomic force microscopic images of EC-based polymer electrolyte film show the escalation of micropores. Fourier transform infrared spectroscopy study supports the complex formation and the interaction between the polymers, salt, and plasticizer. The maximum thermal stability is obtained from thermogravimetry/differential thermal analysis, which is found to be 222 °C for the sample complexed with EC. The cyclic voltagram of the sample having a maximum ionic conductivity shows a small redox current at the anode, and cathode and the chemical stability is confirmed by linear sweep voltammetry.     

LiClO4-doped plasticized chitosan and poly(ethylene glycol) blend as biodegradable polymer electrolyte for supercapacitors

Biodegradable polymer electrolyte comprising the blend of chitosan (CS) and poly(ethylene glycol) (PEG) plasticized with ethylene carbonate and propylene carbonate, as host polymer, and lithium perchlorate (LiClO₄), as a dopant, was prepared by solution casting technique. The ionic conductivity has been calculated using the bulk impedance obtained through impedance spectroscopy. The variation of conductivity and dielectric properties has been investigated as a function of polymer blend ratio, plasticizer content and LiClO₄ concentration at temperature range of 298–343 K. The DSC thermograms show two broad peaks for CS/PEG blend and increased with increase in the LiClO₄ content. The maximum conductivity has been found to be 1.1?×?10^?4 S cm^?1 at room temperature for 70:30 (CS/PEG) concentration. The electric modulus of the electrolyte film exhibits a long tail feature indicative of good capacitance. The activation energy of all samples was calculated using the Arrhenius plot, and it has been found to be 0.12 to 0.38 eV. A carbon–carbon supercapacitor has been fabricated using this electrolyte, and its electrochemical characteristics and performance have been studied. The supercapacitor showed a fairly good specific capacitance of 47 F?g^?1.     

Porous NiO hollow quasi-nanospheres derived from a new metal-organic framework template as high-performance anode materials for lithium ion batteries

Porous hollow metal oxides derived from nanoscaled metal-organic framework (MOF) have drawn tremendous attention due to their high electrochemical performance in advanced Li-ion batteries (LIBs). In this work, porous NiO hollow quasi-nanospheres were fabricated by an ordinary refluxing reaction combination of a thermal decomposition of new nanostructured Ni-MOF, i.e., {Ni₃(HCOO)₆·DMF}_n. When evaluated as an anode material for lithium ion batteries, the MOF derived NiO electrode exhibits high capacity, good cycling stability and rate performance (760 mAh g^?1 at 200 mA g^?1 after 100 cycles, 392 mAh g^?1 at 3200 mA g^?1). This superior lithium storage performance is mainly attributed to the unique hollow and porous nanostructure of the as-synthesized NiO, which offer enough space to accommodate the dramstic volume change and alleviate the pulverization problem during the repeated lithiation/delithiation processes, and provide more electro-active sites for fast electrochemical reactions as well as promote lithium ions and electrons transfer at the electrolyte/electrode interface.     

Investigation on (EC/DMC)(70−x)wt% to LiBETI(x)wt% impact on PVdF-co-HFP/octadecylamine-MMT(montmorillonite) nano clay composite electrolytes

The composition dependence of plasticizer (ethylenecarbonate(EC)/dimethyl carbonate(DMC))_(70?x)wt% to Lithium bis(perfluoroethanesulfonyl)imide(LIBETI)_(x)wt% salt (where x?=?1.5, 3.0, 4.5, 6.0 wt%) on PVdF-co-HFP (25 wt%)/surface modified octadecylamine containing montmorrillonite (ODA-MMT) nano clay (5 wt%) matrix has been investigated by AC impedance, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and dielectric and cyclic voltammetry studies. The enhanced conductivity 2.1?×?10^?5 Scm^?1 is noted in salt rich phase (EC/DMC)_(70–6)wt% /LiBETI_(x=6)wt% (VK4). In XRD, 2θ at 20.9° confirms β-phase. In FTIR studies, vibrational bands 838, 522 and 611 cm^?1 confirm β-phase of PVdF due to clay intercalation. In DSC studies, the melting of α-phase crystallites is noted between 140–150 °C. In SEM studies, one of the membranes presents fern leaf texture confirming swelling of clay. The increase in dielectric constant and dielectric loss with decrease in frequency is attributed to high contribution of charge accumulation at the electrode–electrolyte interface. In cyclic voltammetry studies, salt-rich phase membrane (VK4) shows good cyclability than other membranes.     

Nanoporous carbon microspheres as anode material for enhanced capacity of lithium ion batteries

Nanoporous carbon microspheres (NCMs) are prepared by a one-step carbonizing and activating resorcinol?formaldehyde polymer spheres (RFs) in inert and CO₂ atmosphere for anode materials of lithium-ion batteries (LIBs). Compared with RFs carbon microspheres (RF-C), after activating with hot CO₂, the NCMs with porous structure and high BET surface area of 2798.8 m² g^?1, which provides abundant lithium-ion storage site as well as stable lithium-ion transport channel. When RF-C and NCM are used to anode material for LIBs, at the same current density of 210 mA g^?1, the initial specific discharge capacity are 482.4 and 2575.992 mA h g^?1, respectively; after 50 cycles, the maintain capacity are 429.379 and 926.654 mA h g^?1, respectively. The porous spherical structure of NCM possesses noticeably lithium-ion storage capability, which exhibits high discharge capacity and excellent cycling stability at different current density. The CO₂ activating carbonaceous materials used in anode materials can tremendously enhance the capacity storage, which provides a promising modification strategy to improve the storage capacity and cyclic stability of carbonaceous anode materials for LIBs.     

Effects of lithium bis(oxalato)borate on electrochemical stability of [Emim][Al<Subscript>2</Subscript>Cl<Subscript>7</Subscript>] ionic liquid for aluminum electrolysis

Electrodeposition of aluminum from ionic liquids has been considered a promising approach to low-temperature aluminum electrolysis. In this study, we first investigated the electrochemical stability of 1-ethyl-3-methylimidazolium chloride ([Emim][Al₂Cl₇]) electrolyte, which is a typically used electrolyte for aluminum electrodeposition. It was found that part of imidazole ions decomposed on the cathode during the electrolysis process, especially when the temperature was at or over 353 K. In order to enhance the stability of the electrolyte, we further studied the effects of lithium salt and lithium bis(oxalato)borate (LiBOB), on the electrochemical stability of the [Emim][Al₂Cl₇] ionic liquid system. It was found that the electrochemical window of the electrolyte was broadened from 2.59 to 2.74 V at 373 K by addition of 1 mol% LiBOB. With the existence of LiBOB, the reduction current density of Al₂Cl₇ ^- increased before ?0.58 V and the electrodissolution of Al was more complete. The possible mechanism on the LiBOB increases the stability of the electrolyte systems also discussed based on our theoretical calculations.     

A High‐Performance Anode Material for Li‐Ion Batteries Based on a Vertically Aligned CNTs/NiCo2O4 Core/Shell Structure

3D vertically aligned carbon nanotubes (CNTs)/NiCo₂O₄ core/shell structures are successfully synthesized as binder‐free anode materials for Li‐ion batteries (LIBs) via a facile electrochemical deposition method followed by subsequent annealing in air. The vertically aligned CNTs/NiCo₂O₄ core/shell structures are used as binder‐free anode materials for LIBs and exhibit high and stable reversible capacity (1147.6 mAhg^?1 at 100 mAg^?1), excellent rate capability (712.9 mAh g^?1 at 1000 mAg^?1), and good cycle stability (no capacity fading over 200 cycles). The improved performance of these LIBs is attributed to the unique 3D vertically aligned CNTs/NiCo₂O₄ core/shell structures, which support high electron conductivity, fast ion/electron transport in the electrode and at the electrolyte/electrode interface, and accommodate the volume change during cycling. Furthermore, the synthetic strategy presented can be easily extended to fabricate other metal oxides with a controlled core/shell structure, which may be a promising electrode material for high‐performance LIBs.     

Lithium ion conductivity and dielectric properties of P(VdCl-co-AN-co-MMA)-LiCl-EC triblock co-polymer electrolytes

Lithium ion conducting polymer electrolytes based on triblock polymer P(VdCl-co-AN-co-MMA)–LiCl were prepared using a solution casting technique. XRD studies show that the amorphous nature of the polymer electrolyte has been increased due to the addition of LiCl. The maximum amorphous nature has been observed for 40 m% P(VdCl-co-AN-co-MMA)/60 m% LiCl samples. The FTIR study of the lithium ion conducting polymer membrane confirms the complex formation between the polymer P(VdCl-co-AN-co-MMA) and LiCl. The lithium ion conductivity is found to be 1.6 × 10^?5 Scm^?1 for the 40 m% P(VdCl-co-AN-co-MMA)/60 m% LiCl sample at room temperature. This value is found to be greater than that of pure polymer whose conductivity is found to be 1.5 × 10^?8 Scm^?1. To improve ionic conductivity, ethylene carbonate has been added as a plasticizer to the 40 m% P(VdCl-co-AN-co-MMA)/60 m% LiCl sample. When we add 0.6 m% of ethylene carbonate, it has been observed that the lithium ion conductivity has increased to 1.3 × 10^?3 Scm ^?1 . This value is two orders of magnitude greater than the 40 m% P(VdCl-co-AN-co-MMA)/60 m% LiCl sample. It is also observed from XRD patterns of 40 m% P(VdCl-co-AN-co-MMA)/60 m % LiCl/0.6 m % EC that the amorphous nature has been increased further. A dielectric study has been performed for the above membranes.     

Development of gel polymer electrolytes for application in quantum dot-sensitized solar cells

A methylcellulose–polysulfide gel polymer electrolyte has been prepared for application in quantum dot-sensitized solar cells (QDSSCs) having the configuration FTO/TiO₂/CdS/ZnS/SiO₂/electrolyte/Pt(cathode). The electrolyte with the composition of 30.66 wt.% methylcellulose, 67.44 wt.% Na₂S, and 1.90 wt.% sulfur exhibits the highest conductivity of 0.183 S cm^?1 with the lowest activation energy of 6.14 kJ mol^?1. CdS quantum dot sensitizers have been deposited on TiO₂ film via the successive ionic layer absorption and reaction (SILAR) method. The QDSSC fabricated using the highest conducting electrolyte and CdS QD prepared with five SILAR cycles exhibits a power conversion efficiency (PCE) of 0.78%. After deposition of zinc sulfide (ZnS) and silicon dioxide SiO₂ passivation layers, the PCE of the QDSSC with photoanode arrangement of TiO₂/CdS(5)/ZnS(2)/SiO₂ increased to 1.42%, an improvement in performance by 82%.     

Influence of pyrazole on the photovoltaic performance of dye-sensitized solar cell with polyvinylidene fluoride polymer electrolytes

We investigate the influence of the pyrazole content on the polyvinylidene fluoride (PVDF)/KI/I₂ electrolytes for dye-sensitized solar cells (DSSCs). The solid polymer electrolyte films consisting of different weight percentage ratios (0 20, 30, 40, and 50 %) of pyrazole doped with PVDF/KI/I₂ have been prepared by solution casting technique using N,N-dimethyl formamide (DMF) as a solvent. The as-prepared polymer electrolyte films were characterized by various techniques such as Fourier transform infrared spectroscopy (FT-IR spectroscopy), differential scanning calorimetry (DSC), X-ray diffractometer (XRD), alternate current (AC)-impedance analysis, and scanning electron microscopy (SEM). The 40 wt% pyrazole-PVDF/KI/I₂ electrolyte exhibited the highest ionic conductivity value of 9.52?×?10^?5 Scm^?1 at room temperature. This may be due to the lower crystallinity of PVDF and higher ionic mobility of iodide ions in the electrolyte. The DSSC fabricated using this highest ion conducting electrolyte showed an enhanced power conversion efficiency of 3.30 % under an illumination of 60 mW/cm² than that of pure PVDF/KI/I₂ electrolyte (1.42 %).     

Utilization of saffron (<Emphasis Type="Italic">Crocus sativus L.</Emphasis>) as sensitizer in dye-sensitized solar cells (DSSCs)

Photoelectrodes of dye-sensitized solar cells (DSSCs) have been prepared using nanosized titanium dioxide that have soaked in a solution of different saffron (Crocus sativus L.) spice content in ethanol. The optimized polyacrylonitrile (PAN)-based gel polymer electrolyte with 40.93 wt.% ethylene carbonate, 37.97 wt.% propylene carbonate, 4.37 wt.% tetrapropylammonium iodide, 9.86 wt.% PAN, 1.24 wt.% 1-butyl-3-methylimidazolium iodide, 4.35 wt.% lithium iodide and 1.28 wt.% iodine has been used as the electrolyte for DSSC. The electrolyte has conductivity of 2.91 mS cm^?1 at room temperature (298 K). DSSCs were also sensitized with saffron solution that has been added with 30 wt.% chenodeoxycholic acid (CDCA) co-adsorbent and designated as DSSC P4. The solar cell converts light-to-electricity at an efficiency of 0.31%. This is 29% enhancement in efficiency for the DSSC without addition of CDCA in the saffron-ethanol solution. The DSSC exhibits current density at short-circuit (J _sc ) of 1.26 mA cm^?2, voltage at open circuit (V _oc ) of 0.48 V and 51% fill factor. DSSC P4 also exhibits the highest incident photon-to-current density of more than 40% at 340 nm wavelength.     

Hierarchical Co<Subscript>3</Subscript>O<Subscript>4</Subscript>@C hollow microspheres with high capacity as an anode material for lithium-ion batteries

Three-dimensional hierarchical Co₃O₄@C hollow microspheres (Co₃O₄@C HSs) are successfully fabricated by a facile and scalable method. The Co₃O₄@C HSs are composed of numerous Co₃O₄ nanoparticles uniformly coated by a thin layer of carbon. Due to its stable 3D hierarchical hollow structure and uniform carbon coating, the Co₃O₄@C HSs exhibit excellent electrochemical performance as an anode material for lithium-ion batteries (LIBs). The Co₃O₄@C HSs electrode delivers a high reversible specific capacity, excellent cycling stability (1672 mAh g^?1 after 100 cycles at 0.2 A g^?1 and 842.7 mAh g^?1 after 600 cycles at 1 A g^?1), and prominent rate performance (580.9 mAh g^?1 at 5 A g^?1). The excellent electrochemical performance makes this 3D hierarchical Co₃O₄@C HS a potential candidate for the anode materials of the next-generation LIBs. In addition, this simple synthetic strategy should also be applicable for synthesizing other 3D hierarchical metal oxide/C composites for energy storage and conversion.     

A facile synthesis of heteroatom-doped carbon framework anchored with TiO<Subscript>2</Subscript> nanoparticles for high performance lithium ion battery anodes

Titanium dioxide (TiO₂)-based materials have been well studied because of the high safety and excellent cycling performance when employed as anode materials for lithium ion batteries (LIBs), whereas, the relatively low theoretical capacity (only 335 mAh g^?1) and serious kinetic problems such as poor electrical conductivity (~?10^?13S cm^?1) and low lithium diffusion coefficient (~?10^?9 to 10^?13 cm² s^?1) hinder the development of the TiO₂-based anode materials. To overcome these drawbacks, we present a facile strategy to synthesize N/S dual-doping carbon framework anchored with TiO₂ nanoparticles (NSC@TiO₂) as LIBs anode. Typically, TiO₂ nanoparticles are anchored into the porous graphene-based sheets with N, S dual doping feature, which is produced by carbonization and KOH activation process. The as-obtained NSC@TiO₂ electrode exhibits a high specific capacity of 250 mAh g^?1 with a coulombic efficiency of 99% after 500 cycles at 200 mA g^?1 and excellent rate performance, indicating its promising as anode material for LIBs.