常压介质阻挡放电等离子体发射光谱诊断及其在材料表面改性中的应用

使用介质阻挡放电光谱诊断装置,分析了常压等离子体放电电流与放电间隙的变化关系,提出了“放电临界间隙”的概念,记录和比较了空气和氩气常压介质阻挡放电等离子体发射光谱,并运用同一元素谱线的相对强度来诊断电子温度等物理参量,以达到对材料表面改性过程的实时监控。工作的结果对常压介质阻挡放电及其在材料改性中的应用具有重要的意义。     

纳秒脉冲下单间隙伪火花放电特性

采用单间隙伪火花放电装置,研究了纳秒脉冲下气压、间隙距离和小孔直径对伪火花放电特性的影响。研究结果表明,纳秒脉冲下伪火花放电电压随着气压、间隙距离和小孔直径的增加而减小。通过数值拟合,得到了放电电压与气压、间隙距离和小孔直径间的经验公式。放电电压随着气压、间隙距离和小孔直径的增加而减小,衰减系数分别为0.76,0.39和0.39。     

缩比间隙中辉光放电相似性的初步研究

为了研究缩比实验在气体放电中的有效性, 对缩比间隙中的低气压氩气放电进行了数值模拟. 根据气体放电相似性的猜想, 如果间隙气压p和间隙距离d的乘积为常量, 即p₁d₁=p₂d₂, 并且约化电场E/p 在两个间隙中的空间分布相同, 那么这两个放电间隙的放电特性存在相似性. 数值模拟中设置三个缩比间隙: 气隙A的长度为30 mm, 气压为1 Torr (1 Torr=133.322 Pa); 气隙B的长度为15 mm, 气压为2 Torr; 气隙C的长度为10 mm, 气压为3 Torr. 仿真结果表明, 三个间隙均为辉光放电, 并存在明显的阴极位降区. 间隙A, B, C 的阴极位降区的厚度d_C分别为2.71, 1.35和0.87 mm, 相对应的pd值几乎相同, 即pd_C≈2.70 Torr·mm. 这与氩气辉光放电Paschen曲线最低点(pd≈2.86 Torr·mm)相近. 缩比间隙的放电参数的特性(如工作电压、电场、电流密度、电子密度和离子密度的沿“空间”px的分布)的数值计算结果与放电相似性猜想所预计的结果一致. 所以, 可以认为放电相似性猜想适用于低气压氩气缩比间隙的辉光放电. 关键词： 放电相似性 辉光放电 缩比间隙     

强电离放电产生高浓度臭氧的基础理论与方法研究

论述了介质阻挡强电离放电形成方法及其产生臭氧的等离子反应过程。实现用电场强度、电子能量控制臭氧产生浓度和分解。采用α型Al2O3制成电介质薄层（230um）以及窄放电间隙（110um）的新工艺、新技术、取得折合电场强度E／n大于400Td的强电离放电,电子取得平均能量大于10eV,臭氧浓度达到250g/Nm^3,臭氧产生效率达到200g/kWh。进行实现了臭氧产生装置生产组合模块化、小型化。     

间隙绝缘电极辉光放电实验观察

实验研究了 ITER H₂/He 辉光放电壁处理(GDC)系统的电极合理的间隙绝缘参数及标定辉光过程中 沉积在电极头部的热负载。进行了 H₂/He 击穿电压特性试验,在 ITER GDC 预期的壁离子电流密度条件下研究了 H₂/He 辉光放电电压和试验电极上热负荷与压强的关系、试验电极启辉耐受特性、试验电极温度与热负荷的关系 以及在不同区域辉光放电的气压特性。介绍了 H₂/He 放电期间在电极及其附近区域的溅射和沉积的检测结果以及 对间隙绝缘的影响。为 ITER 辉光放电壁处理系统的设计和运行提供参考。      

基于LabView的监测系统在微细电火花加工中的应用

电火花加工过程中，间隙内进行能量转换，间隙状态的优劣直接影响脉冲电能的转换效果，在微细电火花加工过程中这种影响更加明显。同时，这也是评判放电加工是否顺利进行的主要标准。在科研生产过程中，需要对放电状态，特别是微细电火花放电加工过程中的波形进行研究，因此，组建了一套用于采集放电波形、检测放电状态的放电监测系统。     

常压窄间隙介质阻挡放电等离子体辐射特性

利用带有透明电极与可测向观察的一个介质阻挡放电(DBD)实验装置对它的常压窄间隙等离子体辐射特性进行了实验研究。结果表明：这一DBD装置的辐射特性会受激励电压、激励频率、DBD结构等多种因素影响。在频率为10～20kHz高压电源激励下,采用窄间隙、薄电介质层结构DBD可以大幅度提高放电空间的电场强度,增加放电功率密度,提高了放电装置性能。     

Experimental study on characteristics of nanosecond-pulse surface dielectric barrier discharge

在常规大气环境条件下,基于单极性纳秒脉冲电源对表面介质阻挡放电特性进行了实验研究.结果表明:纳秒脉冲表而介质阻挡放电的本质是丝状放电,放电集中在电压脉冲的上升沿;激励电压和脉冲重复频率越大,放电越强烈,越接近均匀放电,但电压的作用更侧重于均匀性,而频率的作用则侧重于放电的强度;电极间隙的优化可以使表面介质阻挡放电特性最好;玻璃作为阻挡介质时容易发生沿面闪络.     

纳秒脉冲表面介质阻挡放电特性实验研究

在常规大气环境条件下,基于单极性纳秒脉冲电源对表面介质阻挡放电特性进行了实验研究。结果表明:纳秒脉冲表面介质阻挡放电的本质是丝状放电,放电集中在电压脉冲的上升沿;激励电压和脉冲重复频率越大,放电越强烈,越接近均匀放电,但电压的作用更侧重于均匀性,而频率的作用则侧重于放电的强度;电极间隙的优化可以使表面介质阻挡放电特性最好;玻璃作为阻挡介质时容易发生沿面闪络。     

利用发射光谱进行常压介质阻挡放电等离子体诊断及其在材料表面改性上的应用(英文)

使用介质阻挡放电光谱诊断装置,对常压介质阻挡放电在材料改性过程中的等离子体发射光谱进行测量,记录和比较了空气、氦气和氩气常压介质阻挡放电等离子体发射光谱,并运用氩元素谱线的相对强度来诊断电子温度等物理参量,以达到对材料表面改性过程的实时监控。工作的结果对常压介质阻挡放电及其在材料改性上的应用具有重要的意义     

实验研究大气压多脉冲辉光放电的模式和机理

采用稍不平行电极进行大气压He气介质阻挡多脉冲辉光放电实验,通过增强电子耦合器件相机短时曝光照片,研究大气压多脉冲辉光放电在不同时刻的放电模式.通过气隙放电电流、表面电荷计算,理论分析了表面电荷、空间电荷、外加电压与气隙电场强度的关系,研究大气压辉光放电形成多脉冲的机理.实验结果表明,放电首先在间隙稍窄的电极左端开始;在第一个脉冲电流峰值,电极右端也开始放电;第一个电流脉冲经历了Townsend放电到辉光放电的过程;电流脉冲之间的时间内,间隙一直维持着微弱的辉光放电;随后的每个电流脉冲均是辉光放电.理论分析表明,大气压辉光放电的多个电流脉冲是表面电荷、空间电荷与外加电压共同演化的结果;除放电伊始出现Townsend放电外,同一半周期内的放电电流脉冲中不会再出现Townsend放电. 关键词： 介质阻挡放电 增强电子耦合器件 大气压辉光放电 多脉冲     

实验研究大气压多脉冲辉光放电的模式和机理

采用稍不平行电极进行大气压He气介质阻挡多脉冲辉光放电实验,通过增强电子耦合器件相机短时曝光照片,研究大气压多脉冲辉光放电在不同时刻的放电模式.通过气隙放电电流、表面电荷计算,理论分析了表面电荷、空间电荷、外加电压与气隙电场强度的关系,研究大气压辉光放电形成多脉冲的机理.实验结果表明,放电首先在间隙稍窄的电极左端开始;在第一个脉冲电流峰值,电极右端也开始放电;第一个电流脉冲经历了Townsend放电到辉光放电的过程;电流脉冲之间的时间内,间隙一直维持着微弱的辉光放电;随后的每个电流脉冲均是辉光放电.理论分析表明,大气压辉光放电的多个电流脉冲是表面电荷、空间电荷与外加电压共同演化的结果;除放电伊始出现Townsend放电外,同一半周期内的放电电流脉冲中不会再出现Townsend放电.     

Statistical analysis of the effect of dielectric barrier discharge (DBD) operating parameters on the surface processing of poly(methylmethacrylate) film

A dielectric barrier discharge (DBD) plasma, operating in air at atmospheric pressure, has been used to induce changes in the surface properties of poly(methylmethacrylate) (PMMA) films. The relative effects that key DBD operating parameters, specifically: discharge power, electrode gap and duration of exposure have on producing chemical and microstructural changes in the polymer surface region have been investigated. The approach taken involves the application of an orthogonal array experimental design and statistical analysis methodology. The various data sets obtained from these analyses have been used to develop an equation in which induced changes in the surface properties of the DBD modified PMMA films are expressed in terms of the effectiveness of the various processing parameters in producing them.In general, the results obtained clearly indicate that DBD plasma processing is an effective method for the controlled surface modification of PMMA. Relatively short exposures to the atmospheric pressure discharge produces a significant amount of oxygen incorporation at the surface as indicted by a pronounced reduction in water contact angle. Analysis of the role of each of the operating parameters concerned shows that they do indeed have selective effectiveness for inducing resultant surface modification. Duration of exposure to the DBD plasma, expressed here as the number of treatment cycles at a given speed of specimen transit through the electrode gap, was found to play a major role in decreasing the surface wettability of PMMA. Conversely, the magnitude of the discharge power was not a significant parameter in this regard. In contrast, the value of the applied power played the dominant role in achieving the observed enrichment of the surface oxygen abundance, as measured by XPS, with the duration of exposure to the discharge playing a secondary role in this case.The nature and scale of the induced surface changes that originate from the various processing conditions employed have been further considered to determine if an interrelationship exists between them. Non-parametric data analysis indicates that no significant correlation exists between the observed changes in measured polymer wettability and the attendant surface oxygen enrichment. This result suggests that the increase in surface wettability caused by DBD processing, as manifested in a reduced contact angle, is not merely attributable to changes in the surface chemistry. As such, it is postulated that changes in the surface microstructure may also contribute to this change in surface wettability.     

常压介质阻挡放电等离子体发射光谱的检测分析

以常压介质阻挡放电等离子体作为研究对象,在常温常压条件下使用介质阻挡放电光谱诊断装置,得到N2第二正系跃迁和Ar原子发射谱线。通过对放电光谱的检测分析,可以察知常压介质阻挡放电等离子体的特性,并可运用同一元素谱线的相对强度来诊断电子激发温度等物理参量,以达到对材料表面改性过程的实时监控,工作的结果对常压介质阻挡放电及其在材料改性的应用中具有重要的意义。     

Effect of corona discharge on cadmium sulphide and lead sulphide films

This paper describes the effect of corona discharge on cadmium sulphide (CdS) and lead sulphide (PbS) films prepared using the chemical route. The property of films before and after exposure to corona has been described in detail. The electronic properties of the CdS and PbS films have been studied by current-voltage (I-V), capacitance-voltage (C-V) measurements. The structural properties and surface morphology were studied by using X-ray diffraction and scanning electron microscopy before and after exposing to Corona discharge. The films displayed the change in surface morphology after exposure to the corona discharge. It has been found that the films showed an increase in resistivity after exposure. This change in property has been attributed to modification in surface states. Time-dependent recovery indicated that room temperature annealing is sufficient to regain the normal resistivity of the films. The experiment was carried with the aim of studying the effect of the interaction of corona discharge on the semiconductor films and its subsequent effects.     

空气中大气压下均匀辉光放电的可能性

利用介质阻挡电极结构,对101325×105Pa气压下空气间隙中的放电进行了实验研究,数值模拟计算了实验条件下电子雪崩的发展过程.结果表明:对于长度不大于2mm的空气间隙,可能实现辉光放电.对于长度不小于5mm的空气间隙,如果不能设法降低放电场强,放电必然是流注形式,不可能实现辉光放电.另外,实验结果未能验证“离子捕获”机理降低放电场强而实现辉光放电的正确性 关键词： 大气压辉光放电 电子雪崩 流注     

Characteristics of DC discharge in a wire-cylinder configuration at high ambient temperatures

In the present work, the characteristics of direct-current (DC) discharge in a wire-cylinder configuration at an ambient temperature range of 350–850 °C were studied by analyzing photographs of the discharging process and the corresponding V–I characteristics, with the aim of facilitating the application of plasma technology in the fields of energy and the environment. The influences of the ambient temperature, the inter-electrode gap, the gas medium and the cathode material on the DC discharge were investigated. The corona-onset threshold voltage (COTV) and the spark-breakdown threshold voltage (SBTV) decrease as the ambient temperature increases, and the SBTV decreases more rapidly. Increasing the inter-electrode gap enlarges the difference between the SBTV and the COTV. After spark breakdown, in an air atmosphere, glow discharge is more likely to take place under conditions of high ambient temperatures or small inter-electrode gaps. The values of the SBTV in different atmospheres have the following relation: air ≈ O₂ > CO₂. At an ambient temperature range of 350–850 °C and in an atmosphere of N₂, glow discharge and arc discharge occur successively as the output voltage of the power supply is increased, while in an atmosphere of O₂ and CO₂, only corona and arc discharge are successively observed. In an air atmosphere, when the inter-electrode gap is 29 mm, corona, glow and arc discharge occur successively with increasing output voltage when the ambient temperature is 850 °C, while only corona and arc discharge appear when the temperature is 350–750 °C. When the inter-electrode gap is 5 mm in an air atmosphere, corona, glow and arc discharge occur successively in an ambient temperature range of 350–850 °C. The cathode material has a minor influence on the COTV and a more significant influence on the SBTV. In a device using a cathode with a low work function, the SBTV is low, and the power to maintain arc discharge is small.     

大气压管板结构纳秒脉冲放电中时域X射线研究

纳秒脉冲放电能在大气压下产生高电子能量、高功率密度的低温等离子体,由于经典放电理论无法很好地解释纳秒脉冲放电中的现象,近年来以高能逃逸电子为基础的纳秒脉冲气体放电理论受到广泛关注.纳秒脉冲放电会产生高能逃逸电子,伴随产生X射线,研究X射线的特性可以间接反映高能逃逸电子的特性.本文利用纳秒脉冲电源在大气压下激励空气放电,通过金刚石光导探测器测量放电产生的X射线,研究不同电极间隙、阳极厚度下和空间不同位置测量的X射线特性.实验结果表明,在大气压下纳秒脉冲放电能产生上升沿约1 ns,脉宽约2 ns的X射线脉冲,其产生时间与纳秒脉冲电压峰值对应,经计算探测到的X射线能量约为2.3×10-3J.当增大电极间隙时,探测到的X射线能量减弱,因为增大电极间隙会减小电场强度和逃逸电子数,从而减少阳极的轫致辐射.电极间距大于50 mm后加速减弱,同时放电模式从弥散过渡到电晕.随着阳极厚度增加,阳极后方和放电腔侧面观察窗测得的X射线能量均有所减弱,在阳极后面探测的X射线能量减弱趋势更加明显,这说明X射线主要产生在阳极内表面,因此增加阳极厚度会使穿透阳极薄膜的X射线能量减少.