双后向结构的线宽拓展L波段超荧光光源

报道了采用两级级联双后向抽运的光源结构,实现高效率和线宽拓展的L波段掺铒光纤超荧光光源.通过数值模拟,研究了两级光纤长度分配和抽运功率比例对光源输出特性的影响.模拟表明,该结构可获得线宽拓展的平坦L波段光谱,相比常规L波段光谱线宽拓展了15 nm,达近60 nm.此外,抽运功率比例为1∶1时该结构的抽运转换效率最高.利...     

光纤陀螺用掺铒超荧光光纤光源输出特性研究

介绍了掺铒超荧光光纤光源(SFS)的基本原理和SFS各种基本结构的特点。结合实际应用选择了单程后向(SPB) SFS作为光纤陀螺用光源。理论分析了影响单程后向掺铒超荧光光纤光源输出特性的各种因素。通过实验分析了铒纤长度对单程后向掺铒光纤光源泵浦效率和输出光谱的影响,特别是对中心波长稳定性的影响,对于单程后向结构掺铒光纤光源来说,铒纤长度有一个最佳值。演示了铒纤在选择最佳长度的情况下,泵浦功率对输出谱型的影响。通过实验分析了-40℃～60℃之间光源输出光谱和输出光功率的温度稳定性。最终得到了适用于惯导级光纤陀螺的光源。     

芯泵浦高功率宽带谱平坦长波段光纤光源

为了获得高功率、宽带宽及谱平坦的长波段掺铒光纤光源,基于2级双程芯泵浦,应用偏振复用技术实现泵浦瓦级供给,在泵浦总功率和光纤总长度都不变的情况下,数值分析了4种光源结构的输出特性受泵浦和光纤分配比例的影响。结果表明,4种结构基本都能工作于L波段（1 565 nm~1 610 nm）,带宽受结构影响较小,但只有双程后向+双程后向结构可同时拥有高输出功率和高平坦度。其在总泵浦功率750 mW,第一级泵浦功率为300 mW,第二级泵浦功率为450 mW时,和光纤总长度21 m,第一级光纤长度为18 m,第二级光纤长度为3 m时,可实现输出功率314 mW,带宽32.41 nm,中心波长1 584.84 nm,平坦度2.23 dB的L波段超荧光光源。     

高稳定宽频带掺铒光纤超荧光光源

理论研究了双程后向结构掺铒光纤超荧光光源的特性。结果表明 ,在任意反射镜参数下 ,只要选取适当的掺铒光纤长度 ,该结构光源总能实现不依赖于抽运功率的平均波长高稳定性运行 ;在光源高稳定性的前提下 ,反射镜参数优化后的该结构光源具有较宽的频带宽度和较高的抽运效率     

铒纤长度对掺铒光源性能影响的实验研究

实验演示了铒纤长度的选择对1550 nm双通后向超荧光掺铒光纤光源(DPB SFS)的平均波长以及谱宽性能的影响,特别是对平均波长稳定性的影响,实验分析了－20℃~60℃之间光源固有平均波长的变化,最终得到了铒纤固有热系数以及整个样机的平均波长稳定性随铒纤长度变化的实验曲线,对超荧光掺铒光纤光源的器件选择和优化设计具有重要参考价值.     

同带泵浦高功率超荧光光源

报道了一台基于同带泵浦技术的主振荡功率放大(MOPA)结构超荧光光纤光源。首先利用自行搭建的超荧光种子源获得了半高全宽(FWHM)线宽10.3 nm的宽谱超荧光种子,经光谱滤波得到FWHM线宽1.8 nm的窄谱种子光;种子光经二级预放大器放大至104.4 W后注入主放大器;主放大器最高输出功率3.14 kW,最高输出功率时光光转换效率80.74%,光谱FWHM线宽4.68 nm,光束质量因子为1.59。进一步提高系统泵浦功率有望获得更高功率输出。     

Characteristic comparison of single-pumped L-band erbium-doped fiber amplified spontaneous emission sources

We experimentally investigate the single-pumped L-band (1570–1610 nm) erbium-doped fiber amplified spontaneous emission (ASE) source in four configurations with single-pass forward, single-pass backward, double-pass forward (DPF), and double-pass backward structures. The characteristics are examined and compared in terms of the output power, mean wavelength, spectral linewidth, and pumping conversion efficiency. Among them, only DPF configuration is satisfied, and other configurations are intrinsically hard to be an L-band ASE source for applications. Such results are significantly different as compared with their corresponding C-band counterparts.     

L波段高掺铒光纤超荧光光源

采用半导体激光二极管泵浦12cm长高掺铒光纤,在双程前向装置中,获得了10.8mW最大超荧光输出功率,斜率效率10.6%,在1553.1~1588.6nm接近36nm的范围内,功率抖动小于0.2dBm。作为比较,在相同实验条件下泵浦10cm长的高掺铒光纤,结果显示输出光谱带宽明显下降,C波段的放大自发辐射远大于L波段的,由此也证明了L波段的放大自发辐射是由C波段的放大自发辐射泵浦产生的。     

Influence of Er-doped superfluorescent fiber source's spectrum-stability on the SNR of fiber optic gyroscopes

The output spectrum-stability of Er-doped superfluorescent fiber source (SFS) was measured by changing the temperature around the excited Er-doped fiber (EDF). With the experiment results, the influences of the SFS's spectrum-stability on the signal-to-noise ratio (SNR) of fiber optic gyroscope (FOG) were simulated. The simulated results demonstrate that the SNR of FOG will change no matter the power, mean wavelength or the spectral bandwidth of the light output from the Er-doped SFS is changing. The results show that the changing of SNR caused by the output power's variation is three orders of magnitude larger than that caused by the variation of mean wavelength or bandwidth. And the main factor influencing the stability of FOG's SNR is the temperature-stability of the output power of Er-doped SFS.     

铒纤长度对单程掺铒光源输出特性的影响

 分析铒纤长度对掺铒光源输出特性的影响对于光源的优化设计有重要意义。实验分析了铒纤长度对单程前向和后向掺铒光纤光源(SFS)输出特性的影响。分析了铒纤长度与单程SFS输出光功率的关系,以及铒纤长度对单程SFS输出光谱宽度及中心波长的影响。找到了最佳铒纤长度的范围,对单程掺铒光纤光源的器件选择及性能优化有重要的参考价值。     

新型三段高性能的长波段掺铒光纤超荧光光源的研究

提出了一种第一段无泵浦、第二段前向泵浦和第三段后向泵浦的三段级联掺铒光纤超荧光光纤光源的新结构.数值分析了泵浦光波长、铒光纤长度以及泵浦比例对新结构性能的影响.结果表明可以找到一组适合制作成本低廉、输出功率高、谱平坦的长波段掺铒光纤超荧光光源.     

新颖的高功率L-波段掺铒光纤超荧光光源

研究了L-波段超荧光在光纤中的产生机理,设计了一种带光纤圈反射器的双级双程前向输出L-波段光源结构,通过对两级采用掺铒浓度不同的光纤并优化其长度及两级泵浦光功率,实验中获得了功率高达19.86mW(12.98dBm)、中心波长为1577.421nm的L-波段(1555-1620nm)超荧光光源。实现了低浓度掺铒光纤起诱导光及改善光谱的作用,高浓度光纤为主要发光源,采用光纤圈反射器提高了泵浦光的利用效率、光源的平坦度及稳定性。同时分析了结构中各个参量对光源各方面性能的影响,对光源的设计具有指导意义。     

3 dB带宽达80 nm的双包层掺镱超荧光光纤光源

采用大模面积双包层掺镱光纤作为增益介质搭建了一台双程前向超荧光光纤光源,该光源的输出功率随泵浦源注入电流的增加基本呈线性增加,最大输出功率为341 mW。其独特的优势是现实了掺镱光纤最宽的超荧光输出,在输出功率从201～341 mW之间,超荧光光谱的3 dB带宽超过80 nm。其输出功率虽然不是很高,但是在一般情况下能够满足人们对超荧光的需求。从镱离子的能级结构和镱离子在石英基质中的吸收截面与发射截面出发,分析了能够得到最宽超荧光输出的物理原因。这台双包层掺镱超荧光光纤光源由于充分利用了镱离子在1 025和1 075 nm附近的超荧光辐射,因而能够得到3 dB带宽为80 nm的超荧光输出。     

窄线宽纳秒脉冲光纤拉曼放大器的理论模型和数值分析

窄线宽纳秒脉冲光纤拉曼放大器在非线性频率变换、遥感探测和量子信息等领域有广泛的应用前景.综合考虑受激拉曼散射(stimulated Raman scattering,SRS)、受激布里渊散射(stimulated Brillouin scattering,SBS)、自相位调制(self-phase modulation)和交叉相位调制(cross-phase modulation)等非线性效应,建立了窄线宽纳秒脉冲光纤拉曼放大器的非线性动力学模型.仿真分析了放大器中脉冲激光的时频演化特性,对比研究了抽运脉冲宽度、光纤长度和信号光功率等因素对放大器性能的影响.研究发现,上述因素会影响放大器的SRS阈值、SBS阈值、输出激光线宽、激光转换效率等.例如,当脉冲宽度为800 ns时,SBS随着抽运功率的增加而发生,限制了激光功率的提升;减短抽运脉宽可以抑制SBS,但是输出激光的线宽易于展宽到数百MHz以上;增加光纤长度可以获得更低的SRS阈值和更高的转换效率,但是SBS效应和光谱展宽程度也随之增强.系统搭建中需要平衡各非线性效应,选择合适的系统参数.研究内容可以为窄线宽纳秒脉冲光纤拉曼放大器的设计搭建提供参考.     

C- and L-band tunable fiber ring laser using a two-taper Mach-Zehnder interferometer filter

A stable C- and L-band tunable fiber ring laser, using a two-taper Mach-Zehnder interferometer (MZI) as a filter, is proposed and demonstrated experimentally. One of the two taper waists is mechanically bent to tune the laser wavelength. Being amplified by an L-band erbium-doped fiber amplifier and an erbium-doped fiber, respectively, the fiber ring laser has a full L-band (1564-1605nm) and C-band (1550-1565nm) tuning range with a side-mode suppression ratio as high as 50dB. The laser linewidth and the minimum tuning step are related to the MZI's cavity length. It was also found that thermal annealing relieved the internal stresses of the tapers and greatly improved the laser performance.     

基于掺铒光子晶体光纤超荧光光源的实验研究

为了改进传统掺铒光纤超荧光光源的输出稳定性,提出基于掺铒光子晶体光纤的超荧光光源。构建了单程后向结构掺铒光子晶体光纤超荧光光源,研究了这种新型光源的输出特性。分析了掺铒光子晶平均波长体光纤长度和抽运功率对光源输出功率、光谱谱宽和平均波长的影响。结果表明,通过优化选取光纤长度28m和抽运功率220mW,获得了单程后向结构超荧光光源输出如下:输出功率45.74mW、光-光转换效率20.79%、谱宽31.5nm和平均波长1548.003nm。该实验结果为进一步研究掺铒光子晶体光纤超荧光光源在不同环境下的稳定性奠定了基础。     

High-power flat L-band erbium-doped fiber ASE source using dual forward-pumping scheme

We experimentally investigate a high output power L-band (1565–1605 nm) erbium-doped fiber amplified spontaneous emission (ASE) source using dual forward-pumping configuration. Such configuration allows high pumping-power operation and enhances the pumping efficiency. The high pumping efficiency of 36.1% is achieved for such ASE source with a mirror reflectance of 30%. The output power of about 72.2 mW and a linewidth of 40.8 nm with a power ripple of 0.7 dB are obtained without using any external spectral filters.     

Supercontinuum generation in a standard fiber pumped by noise-like pulses from a figure-eight fiber laser

We report the experimental study of broadband spectrum generation in a piece of standard fiber (SMF-28) using as the pump a train of noise-like pulses, or sub-nanosecond packets of sub-ps pulses with randomly varying amplitudes. The pulses are generated by an erbium-doped figure-eight fiber laser, and present a wide (∼50 nm) optical spectrum, which represents a significant advantage to seed the generation of new frequencies. Another advantage of the pulses is their relatively large energy, as they are made up of a large number of ultrashort pulses. After amplification with an Erbium Doped Fiber Amplifier (EDFA), the pulses were injected in a 0.75 km length of SMF-28 fiber. We obtained experimentally at the end of the fiber an output signal spectrum extending from 1530 nm to at least 1750 nm (the upper limit of the spectrum analyzer) for pump pulses with an average power of 20.4 mW, corresponding to a few kilowatts peak power. The spectral broadening is due to Raman self-frequency shift (SFS). It is noteworthy that the spectrum of the newly created frequencies was extremely uniform over the range of measurement. Considering that the Raman shift is directly related to the pump pulse duration, spectral flatness is a direct consequence of the random distribution of amplitudes and durations of the pulses in the packet. Finally, the results show the capabilities of noise-like pulses from a fiber laser for applications in supercontinuum generation based on nonlinear phenomena such as Raman SFS.     

L-band EDFA性能与增益光纤长度关系的分析

分析和模拟L_band EDFA的增益特性对其优化设计和实验有着重要的意义。基于Giles模型,数值模拟了L_band EDFA中的信号光、泵浦光和放大自发辐射(ASE)在一定泵浦功率下与铒光纤长度的关系;分析了L_band EDFA本征增益平坦的产生机理;数值模拟了小信号增益平坦特性。结果表明,在一定的泵浦功率下,如果在所选择的L_bandEDFA中铒光纤长度合适,则不需要任何平坦化处理就可以得到比较平坦的增益谱线。     

A 168-W high-power single-frequency amplifier in an all-fiber configuration

We present a high-power,single-frequency,narrow linewidth fiber amplifier based on master oscillator power amplification chains in an all-fiber configuration.The effect of the delivery fiber on the maximum output power is studied.A home-made 1064-nm seed laser with a 20-kHz linewidth is boosted to 129 W,and limited by stimulated Brillouin scattering(SBS) when the delivery fiber is 1.2 m long.By shortening the delivery fiber length to 0.7 m,the SBS threshold is increased efficiently and the maximum output power rises to 168 W with an 82.9% power conversion efficiency.The experimental results indicate that the output power can be further raised by shortening the delivery fiber length and increasing the pump power.