基于可调光延迟线的光子学微波频率测量

提出了一种基于可调光延迟线的光子学微波频率测量方法.经同一微波信号调制的两个不同波长光载波在经过一段可调色散介质传输后,解调输出两路具有不同相位的微波信号,得到的相干微波功率随着色散量的改变出现周期性变化,由此周期可得到输入微波频率值.采用由8个磁光开关和1.6 km单模光纤构成的7-bit光纤延迟线实现色散量的调节....     

A MZI-based photonic instantaneous microwave frequency measurement simplified by an optical polarizer

A novel photonic scheme of microwave signal frequency measurement with adjustable measurement range and resolution is proposed and experimentally demonstrated. The proposed scheme is based on simultaneous optical phase modulation and intensity modulation with interferometric detection. A low-pass frequency response is achieved by a Mach–Zehnder interferometer (MZI) while a bandpass frequency response is produced by a polarizer placed on the back instead of in front of the MZI. The microwave frequency can be estimated by the measured amplitude comparison function (ACF) obtained from the ratio of the two frequency responses. This scheme is simple, cost-effective as it requires no extra laser sources or modulators in the basic analog modulation link. The measurement errors as shown in experimental results can be kept in 0.1 GHz over a frequency range of 0.1–8.5 GHz.     

基于异步光取样的频率空间压缩法瞬时测频方法

瞬时测频技术是一项重要的电子技术。首次提出了一种基于异步光取样的频率空间压缩法瞬时测频方法。测量带宽可以从直流到40GHz,实验结果表明,响应曲线基本保持平坦响应,测频精度超过0.5MHz,可同时测量多个载波信号频率,在0.2μs或者更短时间内就可以完成一次测频。数值模拟表明,抗噪声性能可达-13dB以上,可以提取掩藏在100倍功率人为干扰中的有用信号频率。     

High-repetitive frequency millimeter-wave signal generation using multi-cascaded external modulators based on carrier suppression technique

We have numerically and experimentally investigated how to generate high-repetitive frequency millimeter (mm)-wave using multi-cascaded intensity modulators based on optical carrier suppression (OCS) scheme. We have found the rule how to generate the high-repetitive frequency mm-wave by adjusting the repetitive frequency of the radio-frequency (RF) signals and the phase relation between the RF signals on the intensity modulators. Based on this rule, we have experimentally demonstrated to generate over 80 GHz optical mm-wave.     

Ultrafast optical delay line by use of a time-prism pair

We demonstrate an all-fiber, programmable, ultrafast optical delay line based on reversible frequency conversion by use of a time-prism pair. Using electro-optic phase modulators to provide the time-prism phase profile, we show a record scanning rate of 0.5 GHz and a delay range of 19.0 ps. Computer modeling suggests that aberration correction in the time-prism system can extend the delay range to 28.0 ps. Finally, limitations and potential improvement of our techniques are discussed.     

Characterization of ROF signal based on cascaded optical carrier suppression modulation technique

The paper experimentally demonstrated the optical frequency quadrupling microwave signal generation, a 4 GHz radio frequency (RF) signals up-conversion to 16 GHz in a radio over fiber (ROF) link, using twice optical carrier suppression modulation. The RF signal was mixed with 1.25 Gbps NRZ-OOK data firstly and then modulated by two cascaded single-electrode optical intensity modulators. The obtained 1.25 Gbps/16 GHz ROF signal was transmitted and characterized in the optical fiber link. At BER of 10^?9, low power penalty of 1.0 and 1.4 dB were obtained over a fiber link with a transmission distance of 25 and 50 km.     

Switchable instantaneous frequency measurement by optical power monitoring based on DP-QPSK modulator

We propose and analyze an instantaneous frequency measurement system by using optical power monitoring technique with improved resolution. The primary component adopted in the proposal is a dual-polarization quadrature phase shift keying (DP-QPSK) modulator which is used to modulate the microwave signal that has a designed time delay and phase shifting. The generated optical signal is sent to polarization beam splitter (PBS) in DP-QPSK modulator. Owing to the complementary transmission nature of polarization interference introduced by PBS, the frequency information is converted into the optical power and the relationship between the amplitude comparison function (ACF) and microwave frequency to be measured is established. Thus, the frequency of the microwave signal can be easily measured through monitoring the optical powers of the two output ports of the PBS. Furthermore, by adjusting the direct current (DC) biases of the DP-QPSK modulator instead of changing the electrical delay, the measurement range and resolution can be switched. In this paper, the basic principle of the instantaneous frequency measurement system is derived in detail, and simulation has been performed to investigate the resolution, the measurement range, and the influence of imperfection devices. The proposed scheme is wavelength-independent and its measurement range is switchable, which can avoid the laser wavelength drifting problem and thus greatly increasing the system flexibility.     

Generation of very flat optical frequency combs from continuous-wave lasers using cascaded intensity and phase modulators driven by tailored radio frequency waveforms

We demonstrate a scheme based on a cascade of lithium niobate intensity and phase modulators driven by specially tailored RF waveforms to generate an optical frequency comb with very high spectral flatness. In this Letter, we demonstrate a 10 GHz comb with 38 comb lines within a spectral power variation below 1 dB. The number of comb lines that can be generated is limited by the power handling capability of the phase modulator, and this can be scaled without compromising the spectral flatness. Furthermore, the spectral phase of the generated combs in our scheme is almost purely quadratic, which, as we will demonstrate, allows for high-quality pulse compression using only single-mode fiber.     

Simulation of a flat optical frequency comb using a single-drive multi-RF Mach–Zehnder modulator in a cascaded intensity modulator chain

We proposed a scheme based on two cascaded lithium niobate intensity modulators to generate an optical frequency comb with very high flatness. Single-drive multi-RF waveforms are used for driving the first intensity modulator, and 9 lines within 1 dB power variation can be obtained. When cascading with another intensity modulator, by specially adjusting the DC bias and the drive amplitudes of the RF signals of the two intensity modulators, 27 or 45 comb lines with a spectral power variation about 1 dB are obtained. The scheme is relatively simple and adjustable, and the frequency interval of the OFC varies with microwave frequency applied on modulators.     

A cascaded traveling-wave electrooptic modulator

A novel configuration for a wide-band and low-drive power electrooptic modulator is proposed. The device is based on the compensation for the velocity difference between the electrical and optical signals by adjusting their relative delay between two succussive modulators. A cascaded traveling-wave optical modulator having a band-width of approximately 3 GHz and a required power of 150 mW for 30% linear modulation has been constructed.     

Instantaneous frequency measurement based on transversal microwave filters with high resolution

We propose a novel photonic technique for microwave frequency measurement based on transversal microwave filters with high resolution. Two parallel microwave filters with sine and cosine frequency responses are obtained by cross gain modulation in a single semiconductor optical amplifier, which introduces two different frequency responses to achieve an amplitude comparison function. We also demonstrate a proof- of-concept experiment. The measurement error is less than ±0.04 GHz for the first band range of 0–3.45 GHz and less than ±0.03 GHz for the second band range of 3.45–5.8 GHz. Our scheme is found to be capable of being extended for larger frequency range measurements using a shorter fiber length.     

Photonic vector signal generation employing a novel optical direct-detection in-phase/quadrature-phase upconversion

This work demonstrates the feasibility of the generation of an RF direct-detection vector signal using optical in-phase/quadrature-phase (I/Q) upconversion. The advantage of the proposed transmitter is that no electrical mixer is needed to generate the RF signal. Therefore, I/Q data of RF signals are processed at baseband at the transmitter, which is independent of the carrier frequency of the generated RF signal. A 10 Gb/s 16 quadrature amplitude modulation signal is experimentally demonstrated. Following transmission over a 50 km single-mode fiber, the power penalty is negligible. Moreover, I/Q imbalance of the proposed transmitter is studied and compensated by digital signal processing, which is both numerically and experimentally verified.     

A novel optical mm-wave generation scheme based on three parallel Mach-Zehnder modulators

We propose a novel optical mm-wave generation scheme based on three parallel Mach-Zehnder modulators (MZMs) for the first time. First, the scheme is investigated theoretically, which suggests that it can be used for sextupling, 12-tupling, and 18-tupling mm-wave generation. Then simulation results are given, 60 GHz mm-wave is generated from 5 GHz, or 10 GHz RF oscillator based on frequency 12-tupling or sextupling, and 90 GHz mm-wave is generated from 5 GHz RF oscillator based on frequency 18-tupling. The optical sideband suppression ratio (OSSR) and the radio frequency spurious suppression ratio (RFSSR) are analyzed by simulation, in which several non-ideal factors are taken into consideration. Results indicate that all the three mm-wave generation methods are practical and very good performance can be obtained when the extinction ratio of the MZM is 30 dB, even if the extinction ratio of the MZM is 20 dB, the performance is still good, especially for the sextupling mm-wave generation method, whose performance is excellent and insensitive to the extinction ratio of MZM, the non-ideal RF driving voltage and the non-ideal DC bias. At last, we set up a RoF system by simulation to verify the transmission performance of the scheme. The BER performance and eye diagrams are given.     

Carrier suppression in quadruple frequency modulation by cascaded optical external modulators for millimeter-wave generation

The optical carrier suppression in optical quadruple frequency modulation by cascaded external modulators is investigated theoretically and experimentally. Theoretical analysis demonstrates that the optical carrier suppression ratio is related with not only the initial phase difference of electrical signals applied on the two modulators, but also the optical phase shift between the two modulators. The maximum suppression ratio can be achieved when the total phase difference is equal to nπ＋π/2 （n = 1, 2,…）, which is verified by experiments. By properly controlling the total phase shift, 40-GHz millimeter-wave is generated by using a 10-GHz radio frequency （RF） source and the modulators.     

新型四倍频光生毫米波矢量信号调制技术

提出一种基于双并联马赫-曾德尔调制器(MZM)的新型四倍频光生毫米波技术,并用于矢量信号调制。传统的四倍频调制技术,由于数据信号同时调制到+2,-2阶边带上,拍频检测后两个边带上数据信号会产生相位叠加,只适用于不归零码(NRZ)等强度调制格式。提出的矢量信号调制技术将数据信号调制在一个-1阶边带上,另一个+3阶边带不携带数据,在拍频检测后幅度和相位信息被正确保留。同时,四倍频模块降低了传输过程中对电和光器件的带宽需求。理论分析和仿真结果表明,通过此方法产生的携带在60GHz载波上的6.25×108 symbol/s的四相相移键控(QPSK)信号,经过20km单模光纤传输后,误差向量幅度(EVM)损耗可以忽略。     

Photonic approach to the simultaneous measurement of the frequency, amplitude, pulse width, and time of arrival of a microwave signal

A photonic approach to the simultaneous measurement of the frequency, pulse amplitude (PA), pulse width (PW), and time of arrival (TOA) of an unknown pulsed microwave signal is proposed and demonstrated. The measurement is performed based on optical carrier-suppressed modulation, complementary optical filtering, low-speed photodetection, and electrical signal processing. A proof-of-concept experiment is carried out. A frequency measurement range of 2-11 GHz with a measurement error for frequency, PA, PW, and TOA within ±0.1 GHz, ±0.05 V, ±1 ns, and ±0.16 ns is achieved.     

Analysis of an optical mm-wave generation scheme with frequency octupling using two cascaded Mach-Zehnder modulators

We propose a novel method to generate optical mm-wave signals with frequency octupling using two cascaded Mach-Zehnder modulators (MZMs). First, the scheme is investigated both theoretically and by simulation, and results show that an 80 GHz mm-wave is generated by a 10 GHz RF oscillator. Then, an analytical expression is developed to describe the performance of the scheme. The influences caused by non-ideal factors are discussed in detail, and undesired sidebands suppression ratios are plotted and analyzed. At last a RoF system using the mm-wave generation scheme is demonstrated and its BER curves indicate that the performance of the system is still good even if the parameters deviate from the ideal values to a certain degree.     

Simulative investigation the impact of optical amplification techniques on single- and dual-electrode MZM and direct modulator's in single-tone RoF system

Since the introduction of erbium-doped fiber amplifier (EDFA) in optical fiber communication systems at 1550 nm, the fiber loss is no longer considered as the limiting factor but the fiber dispersion and chirp parameters play an important role in degrading the performance of optical communication systems. Further, the invention of external modulators of Mach-Zehnder (MS) type minimizes the transmission power penalty due to fiber chromatic dispersion as these modulators are consider almost chirp-free modulators. Also, better suppression of nonlinear distortions consists of harmonic distortions (HDs) and intermodulation distortions (IMDs) were achieved by using Mach-Zehnder external modulator [8]. In this work, a simulation comparison of external- and direct-modulation schemes using different optical amplifiers; SOA and EDFA in single-tone RoF system is reported. A single-tone channel of 20 GHz is transmitted over single-mode fiber (SMF) either externally modulated by using single-electrode (SEMZM) - and dual-electrode (DEMZM) - Mach-Zehnder modulator or by direct-modulation scheme. Better improvements in the measurement of received RF power of a 20 km linked single-tone RoF system are achieved by using SEMZM with EDFA, which means maximum optical link is achieved between Central Office (CO) and Base Station (BS). Further, this scheme provides better BER as compare to other schemes discussed in this paper.     

磁绝缘线振荡器谐振腔的高频特性研究

 利用数值方法计算了磁绝缘线振荡器(MILO)主慢波结构谐振腔和扼流腔的谐振频率和场分布。结果表明：当主慢波结构腔内半径为4.6 cm,扼流腔内半径为4.2 cm，阴极半径为3 cm时，MILO工作在3.6~4.4 GHz频率范围，扼流片可以阻止微波功率向脉冲功率源泄漏，这有利于提高器件微波输出的功率；4.5~4.9GHz频段为慢波结构的阻带，微波在该频段截止。计算了C波段MILO开放腔的谐振频率，当模式分别为3π/8,π/2,5π/8,3π/4时，其谐振频率分别为3.18,3.76,4.00,4.11 GHz;并通过实验测出了开放腔的谐振频率,其相应的值分别为3.80,3.94,4.08.4.18 GHz, Q分别为194，143，231，468。数值计算的谐振频率与实验测出的频率基本一致。     

A novel MI-insensitive and filterless frequency octupling scheme based on two parallel dual-parallel Mach–Zehnder modulators

A novel MI-insensitive and filterless frequency octupling scheme based on two parallel dual-parallel Mach–Zehnder modulators (DP-MZMs) is proposed. The proposed scheme is not sensitive to modulation index and relatively strong MMW signal with good radio frequency spurious suppression ratio (RFSSR) can be obtained without strict requirement on modulation index. Filterless feature makes the scheme quite suitable for wavelength division multiplexing (WDM) applications. For verification, a 60 GHz millimeter wave with 44 dB RFSSR is generated from a 7.5 GHz radio frequency wave by simulation. Performance of the proposed scheme has been characterized under different conditions including DC-bias drifts of MZMs, different amplitudes of RF inputs and different extinction ratios of MZMs.