基于级联光纤光栅的双模外腔半导体激光器的实验研究

实现了使用两个级联的光纤Bragg光栅的外腔半导体激光器的双模运转.两个模的峰值波长取决于光纤Bragg光栅的峰值反射波长,分别为1531.5nm与1549.4nm.注入电流为53mA时,两模峰值功率达到均衡为0.5mW,边模抑制比为27dB.     

基于级联光纤Bragg光栅的外腔半导体激光器三波长同时激射

实现了使用3个级联的光纤Bragg光栅外腔半导体激光器3波长同时激射.3条谱线的峰值波长取决于光纤Bragg光栅的峰值反射波长,分别为1 531.5 nm、1 549.4 nm与1 554.8 nm.注入电流为52 mA时,激光器总输出功率为1 mW.该激光器的主要优点包括,由于输出波长被锁定在光纤Bragg光栅的Bragg波长上,因此输出波长稳定,谱线窄,成本低.可应用于多波长干涉测量以及全光通信等领域中.     

全光纤激光相干合成光谱响应特性研究

基于N-腔镜谐振腔理论对全光纤激光相干合成进行了理论分析，数值模拟了迈克尔逊型相干合成激光器的光谱特性，对两个光纤Bragg光栅的中心波长差和两路光的光程差对合成光谱特性的影响给出了理论解释.用啁啾光纤光栅取代其中一个光纤Bragg光栅，使激光相干合成的带宽由0.3 nm拓展到1.0 nm.     

用于抽运铯蒸气激光器的半导体激光器波长稳定与线宽窄化研究

针对铯蒸气激光器对窄线宽与高稳定852nm半导体激光抽运源的要求,采用体布拉格(Bragg)光栅作为外腔输出镜,研究了体Bragg光栅衍射效率对外腔半导体激光器输出光谱特性的影响。研究结果表明,衍射效率为24%、32%与37%的体布拉格光栅均能够改善半导体激光器输出光谱特性;输出光束中心波长锁定在852nm附近、输出线宽约为0.26nm;外腔半导体激光器输出波长随抽运电流、温度的变化速率分别小于10.4pm/A、7.2pm/℃,优于自由运行半导体激光器;随着光栅衍射效率增加,全系统外腔效率从91%降低至86%。     

两路关联光纤激光器互注入锁相实验

基于角锥互注入锁相相干合成方案,利用光纤Bragg光栅（R=85％@1064nm）作为两路光纤激光器的共用腔镜,实现了两路光纤激光器相关联,进一步提高了激光的互注入能量。采用外腔结构,较容易实现了两路光纤激光器的能量互注入锁相。在实验上观察到了远场清晰稳定的干涉条纹（可见度超过0．8）,获得了功率合成效率约为80％的线偏振相干激光输出。     

基于光纤光栅的可调谐半导体激光器

本文利用光纤光栅(FBG)形成外腔反馈及F-P半导体激光器的多模特性,得到波长稳定、可调谐的半导体激光光源,系统研究了不同反馈比率对激光器光谱特性的影响.通过向FBG施加轴向拉力和压力可实现10nm的波长调谐,得到一系列波长间隔0.94nm的激光输出,边模抑制比达35dB,光谱线宽小于0.2nm.     

大功率多波长可转换双包层光纤激光器

在多模掺镱双包层光纤上,利用相位掩模法直接写制Bragg光栅作为激光器后腔镜,得到多波长激光输出.在室温下,通过调节偏振控制器可以得到稳定的单波长及多波长的激光输出,输出波长范围在1 056～1 061 nm,线宽均小于0.02 nm.在25 W的976 nm激光泵浦下,激光器得到功率为6 W的多波长输出.     

基于激光器激射特性的新型应变传感系统

报道了一种基于掺铒光纤激光器瞬态特性的新型应变传感系统.用光纤环反射镜和光纤Bragg光栅(FBG)构成Fabry-Perot线型腔.腔内插入一个长周期光纤光栅(LPG)，其透射谱的中心波长为1574.4nm.FBG的带宽为0.23nm，不受力时其反射波长为1557.98nm，位于LPG的透射谱左沿；当FBG受力时激射波长向长波方向移动，激光通过LPG时透射损耗增大，腔损耗的增加将使激光激射延迟时间增加.因此，应变的大小可以通过激光产生的延迟时间来测量.这种新型应变传感器的分辨率和灵敏度由抽运光脉冲的高、 关键词： 应变传感 光纤激光器 时域测量 光纤Bragg光栅     

光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法 ,在D形内包层掺Yb3 双包层光纤一端直接写制出Bragg光栅 ,用作双包层光纤激光器的输出腔镜 .试验得到了线宽为 0 196nm ,波长为 10 5 8 2nm ,最高输出功率为 5 70mW的稳定激光输出 ,解决了激光器中模式竞争造成的输出不稳定现象 .从速率方程出发 ,对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析 ,结果与实验符合很好     

光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法，在D形内包层掺Yb3+双包层光纤一端直接写制出Bragg光栅，用作双包层光纤激光器的输出腔镜.试验得到了线宽为0.196nm，波长为1058.2nm，最高输出功率为570mW的稳定激光输出，解决了激光器中模式竞争造成的输出不稳定现象.从速率方程出发，对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析，结果与实验符合很好. 关键词： 双包层光纤光栅 掺Yb3＋双包层光纤激光器 相位掩模 速率方程     

Wavelength stabilization of a 980-nm semiconductor laser module stabilized with high-power uncooled dual FBG

An optimized dual fiber Bragg grating (FBG) is proposed for 980-nm semiconductor lasers without thermoelectric coolers to restrict temperature-induced wavelength shift.The mathematical model of the temperature-induced wavelength shift of the laser with the dual FBG is built using the external cavity feedback rate equations.The external cavity parameters are optimized for achieving the stability mode-locking laser output.The spectral characteristics of the dual FBG stabilized laser are measured to range from 0 to 70 °C.The side mode suppression ratio (SMSR) is more than 45 dB,while the full-width at half-maximum (FWHM) is less than 1 nm.The peak wavelength shift is less than 0.1 nm.The dual FBG wavelength shift proportional coefficient is between 0.1086 and 0.4342.     

Multi-peak output Tm-doped silica fiber laser based on femtosecond-written multi-mode fiber Bragg grating

The all-fiber Tm-doped double-clad laser was reported, incorporating a phase mask scanning technology writing FBG directly into the Tm-doped multi-mode fiber core as cavity mirror, using 800 nm femtosecond laser sources. A fiber grating of 12 mm length was realized with a period of 1.35 μm. Pumped by the 793 nm pigtail fiber output LD, the continuous wave (CW) power could scale to 25.4 W at 1.96 μm with the slope efficiency of 38% respected to the LD output power. The output laser spectrum exhibited multi-peak, due to the multi-mode FBG reflective characteristic.     

Theoretical investigation into spectral characteristics of a semiconductor laser with dual-FBG external cavity

A new theoretical model of the dual-FBG external cavity based on the couple-mode theory has been proposed for controlling the output spectral characteristics of the semiconductor laser with dual-FBG external cavity. The output spectral characteristics have been studied through the analyses of the external cavity length, the FBG length and the fiber length between the two FBGs. The results reveal that the side mode suppression ratio (SMSR), the full wave at half maximum (FWHM), the longitudinal mode interval (LMI) and the stability of the central wavelength are mainly determined by the effective external transmissivity, the fiber length between the two FBGs and the external cavity length, respectively. Furthermore, the rising/falling tendencies of the SMSR and the FWHM are exactly opposite. There exist the maximum of the SMSR and the minimum of the FWHM in a semiconductor laser with dual-FBG external cavity. The increase of the fiber length between the two FBGs results in the exponential decrease of the LMI. The increase of the external cavity length leads to the better stability of the central wavelength.     

A pump power controlled 1,060 nm multiwavelength fiber ring laser using nonlinear polarization rotation of SOA

We propose and experimentally demonstrate a both channel spacing and wavelength-tunable 1,060 nm multiwavelength fiber laser using nonlinear polarization rotation of semiconductor optical amplifier (SOA). The SOA in the cavity can not only provide the gain but also generate a pump power controlled phase-shift between two orthogonal linear states of polarization. The experimental result shows that the fast and continuous wavelength tuning is achieved with external light injection, while the channel spacing of the multiwavelength laser can be varied by adjusting the length of polarization maintaining fiber. When an external laser source with 13 dBm power is injected into the SOA as a control pump, optically tunable operation of up to 20 wavelength channels, from 1,042 to 1,058 nm, with a wavelength spacing of 0.8 nm has been demonstrated with the signal-to-spontaneous-noise ratio over 40 dB at room temperature. The lasers are stable with a maximum power fluctuation per channel of less than 0.5 dB during 2-h test.     

Low-threshold performance of fiber Bragg grating external-cavity semiconductor lasers using genetic algorithms

The lowest threshold current of the external-cavity semiconductor laser with fiber Bragg grating using genetic algorithms is investigated. Effects of the external cavity length, coupling efficiency and anti-reflection coating reflectivity on static characteristics, such as L-I curves and side mode suppression ratios (SMSR) are investigated by using multi-mode rate equation. It is found that the reflectivity of the anti-reflection coating for low-threshold performance needs to be increased at the cost of the stability of the fiber grating external-cavity semiconductor laser. The optimal external cavity length obtained by genetic algorithms can be used to obtain the lowest threshold current for sacrificing a little SMSR. However, with the decrease of AR-coating reflectivity, output powers and SMSRs are slightly dependent on the external cavity length.     

体布拉格光栅外腔半导体激光器光谱特性研究

用体布拉格光栅(VBG)作为反馈元件与瓦级半导体激光器(LD)以及快轴准直柱透镜构成一个可以将半导体激光器的工作波长稳定在体布拉格光栅布拉格波长处的外腔激光器。测量了体布拉格光栅外腔激光器的波长稳定性与其工作电流、热汇温度、激光束准直装置等因素的关系。分析了波长稳定效果与半导体激光器增益谱特性、外腔结构参量等因素的关系。研究表明,在相同的工作电流、热汇温度下,当准直柱透镜直径为0.4 mm时的波长稳定效果较好;在此情况下,当热汇温度控制在30℃,工作电流从0.5 A增加到1.5 A的测量范围内,以及当工作电流固定在1.5 A,热汇温度从20℃增加到35℃时,测得的光谱特性表明,半导体激光器的工作波长可以很好地稳定在体布拉格光栅的布拉格波长处。与该激光器在同样条件下自由运转的光谱比较,可以看到,自由运转激射波长与体布拉格光栅的布拉格波长差值小于2.6 nm情况下,可以获得很好的波长稳定效果。实验也表明,当该值大于4.8 nm时波长稳定效果变差。     

Experimental Study on Single Frequency Semiconductor Lasers with Fiber Bragg Reflector External Cavity

ＥｘｐｅｒｉｍｅｎｔａｌＳｔｕｄｙｏｎＳｉｎｇｌｅＦｒｅｑｕｅｎｃｙＳｅｍｉｃｏｎｄｕｃｔｏｒＬａｓｅｒｓｗｉｔｈＦｉｂｅｒＢｒａｇｇＲｅｆｌｅｃｔｏｒＥｘｔｅｒｎａｌＣａｖｉｔｙ￥ＡＮＨｏｎｇｌｉｎ；ＬＩＮＸｉａｎｇｚｈｉ；ＹＡＮＨｏｎｇ；ＣＵＩＸ...     

Spectrum Improvement of a High-Power Broad-Area Laser Diode Based on a Grating Semi-Feedback External Cavity Scheme

We propose a grating semi-feedback external cavity (GSFEC) scheme for high-power broad-area laser diodes for improving the spectrum characteristics of high-power semiconductor lasers. We design this scheme as two crossed cylindrical resonators employing a holographic diffraction grating and a rectangular highly reflecting mirror. In our experiments, we obtain stable spectrum characteristics over a tuning range of 5 nm, with maximum output power up to 764 mW at an operating current of 3.5 A. The wavelength drift rate with injection current decreases from 0.59 nm/A of free-running condition to 0.2 nm/A, and the laser bandwidth is compressed to 21.5% at 2 A.