Changes in Structural and Optical Properties of Polycarbonate Induced by Ag+ Ion Implantation

Transparent polycarbonate samples were implanted with 1 MeV Ag⁺ ions to various doses ranging from 5 × 10¹⁴ to 3 × 10¹⁶ ions cm^?2 with a beam current density of 900 nA cm^?2. Modification in the structure of polycarbonate as a function of the implantation fluence was investigated using micro-Raman spectroscopy, glancing angle X-ray diffraction, and UV-Vis spectroscopy. Raman spectroscopy pointed toward the formation of graphite structures/clusters due to the ion implantation. UV-Vis absorption analysis suggests the formation of a carbonaceous layer and a drastic decrease in optical band gap from 4.12 eV to 0.50 eV at an implanted dose of 3 × 10¹⁶ ions cm^?2. The correlation between the decrease in band gap and the structural changes is discussed.     

Resonance Raman study of He+ ion implanted nanostructured ZnS

ZnS nanocrytsals of size ∼2.5 nm were prepared by chemical precipitation technique. Pressed pellets of nanostructured ZnS were implanted with He⁺ ions at doses of 5 × 10¹⁴, 1 × 10¹⁵ and 5 × 10¹⁵ ions/cm². Raman spectra of both unimplanted and He⁺ ion implanted samples were recorded with ultraviolet (UV) excitation. LO, 2LO, 2TO, (LO + TA) and (2TO − TA) modes of ZnS were observed in the resonance Raman spectra of the unimplanted nanostructured ZnS samples. In addition, a surface mode was observed at 294 cm⁻¹. With the implantation of He⁺ ions, the 2TO mode disappeared and 2LO mode became prominent and this observation was attributed to the decrease in band gap of ZnS nanocrytsals due to ion implantation. The exciton–LO phonon coupling strength was determined from the intensity ratio of 2LO to LO modes and it was observed that the exciton–LO phonon coupling strength increases with increase in implantation dose. In the present work, we report for the first time the observation of 2TO mode in the resonance Raman spectrum of nanostructured ZnS and also the modification of exciton–LO phonon coupling strength of semiconductor nanoparticles by ion implantation. Copyright © 2008 John Wiley & Sons, Ltd.     

离子注入ZnO薄膜的拉曼光谱研究

室温下,用80 keV N⁺和400 keV Xe⁺离子注入ZnO薄膜,注入剂量分别为5.0×10¹⁴—1.0×10¹⁷/cm²和2.0×10¹⁴—5.0×10¹⁵/cm².利用拉曼散射技术对注入前后的ZnO薄膜进行光谱测量和分析,研究了样品的拉曼光谱随离子注入剂量的变化规律.实验结果发现,未进行离子注入的样品在99,435 cm<     

Crystalline to amorphous transformations in ion implanted GaP

Abstract

The amorphization process of GaP by ion implantation is studied. The samples of 〈111〉 oriented GaP were implanted at 130 K with various doses 5 × 10¹³-2 × 10¹⁶ cm^?2 of 150 keV N⁺ ions and with the doses of 6 × 10¹²-1.5 × 10¹⁵ cm^?2 of 150 keV Cd⁺ ions. Room temperature implantations were also performed to see the influence of temperature on defect production. Rutherford backscattering and channelling techniques were used to determine damage in crystals. The damage distributions calculated from the RBS spectra have been compared with the results of Monte-Carlo simulation of the defect creation.

The estimated threshold damage density appeared to be independent on ion mass and is equal 6.5 × 10²⁰ keV/cm³. It is suggested that amorphization of GaP is well explained on the basis of a homogenous model.     

Carbon (70 MeV) and copper (120 MeV) ions irradiation effects in Makrofol-N

Makrofol-N polycarbonate was irradiated with carbon (70 MeV) and copper (120 MeV) ions to analyze the induced effects with respect to optical and structural properties. In the present investigation, the fluence for carbon and copper beams was kept in the range of 1×10¹¹– 1×10¹³ ions/cm² to study the swift heavy ion induced modifications. UV–VIS, FTIR and XRD techniques were utilized to study the induced changes. The analysis of UV–VIS absorption studies revealed that the optical energy gap was reduced by 17% on carbon irradiation, whereas the copper beam leads to a decrease of 52% at the highest fluence of 1×10¹³ ions/cm². The band gap can be correlated to the number of carbon atoms, N, in a cluster with a modified Robertson's equation. In copper (120 MeV) ions irradiated polycarbonate, the number of carbon atoms in a cluster was increased from 63 to 269 with the increase of ion fluence from 0 to 1×10¹³ ions/cm², whereas N is raised only up to 91 when the same polymer films were irradiated with carbon (70 MeV) ions under similar conditions. FTIR analysis showed a decrease in almost all characteristic absorption bands under irradiation. The formation of hydroxyl (? OH) and alkene (C?C) groups were observed in Makrofol-N at higher fluence on irradiation with both types of ions, while the formation alkyne end (R? C≡ CH) group was observed only after copper ions irradiation. The radii of the alkyne production of about 3.3 nm were deduced for copper (120 MeV) ions. XRD measurements show a decrease in intensity of the main peak and an increase of the average intermolecular spacing with the increase of ion fluence, which may be attributed to the structural degradation of Makrofol-N on swift ion irradiation.     

Orientation of sp2 carbon nanoclusters in ion‐implanted polymethylmethacrylate as revealed by polarized Raman spectroscopy

Raman spectroscopy is widely used for the characterization of bonding type in carbon‐based materials, including carbonized surface layer in ion‐implanted polymers. Studies of the polarization properties of Raman scattering from amorphous carbonaceous materials, however, are very scarce. In this paper, we investigate the polarized Raman spectra of polymethylmethacrylate (PMMA) implanted with 50‐keV Si⁺ ions at fluences in the range 3.2 × 10¹⁴–1.0 × 10¹⁷ ions/cm² and for different visible excitation wavelengths. The spectra of the implanted samples are dominated by the D‐ and G‐bands of sp² carbon, which evidence strong carbonization of the ion‐modified layer. The multiwavelength excitation allowed us to resonantly probe the depolarization ratios for sp² clusters of different sizes. We established that the depolarization ratio ρ_G of the G‐band correlates with the sp² cluster size approaching the random orientation limit of 0.75 for the smallest clusters and a limiting value of 0.41 for the largest clusters. The experimental findings give evidence for a preferable orientation of the larger size clusters with their hexagonal planes perpendicular to the surface of the sample. A plausible explanation for such an arrangement is that the sp² clusters form tile‐like arrangements along the ion tracks. This finding may give clues for understanding of the strong transconductance of the ion‐modified layer, and open prospects for the application of polarized Raman spectroscopy as a characterization tool for surface morphology in ion‐implanted materials. Copyright © 2010 John Wiley & Sons, Ltd.     

Surface disorder in c-Si induced by swift heavy ions

The disorders induced in crystalline silicon (c-Si) through the process of electronic energy loss in the swift heavy ion irradiation were investigated. A number of silicon <1 0 0> samples were irradiated with 65 MeV oxygen ions at different fluences, 1×10¹³ to 1.5×10¹⁴ ions/cm², and characterized by the Raman spectroscopy, the optical reflectivity, the X-ray reflectivity, the atomic force microscopy (AFM) and the X-ray diffraction (XRD) techniques. The intensity, redshift, phonon coherence length and asymmetric broadening associated with the Raman peaks reveal that stressed and disordered lattice zones are produced in the surface region of the irradiated silicon. The average crystallite size, obtained by analyzing Raman spectrum with the phonon confinement model, was very large in the virgin silicon but decreased to<100 nm dimension in the ion irradiated silicon. The results of the X-ray reflectivity, AFM and optical reflectivity of 200–700 nm radiation indicate that the roughness of the silicon surface has enhanced substantially after ion irradiation. The diffusion of oxygen in silicon surface during ion irradiation is evident from the oscillation in the X-ray reflectivity spectrum and the sharp decrease in the reflectivity of 200–400 nm radiation. The rise in temperature, estimated from the heat spike model, was high enough to melt the local silicon surface. The results of XRD indicate that lattice defects have been induced and a new plane <2 1 1> has been formed in the silicon <1 0 0>after ion irradiation. The results of the present study show that the energy deposited in crystalline silicon through the process of electronic energy loss ～0.944 keV/nm per ion is sufficient to induce disorders of appreciable magnitude in the silicon surface even at a fluence of ～10¹³ ions/cm².     

Lattice disorder produced in GaAs by 60 keV Cd ions and 70 keV Zn ions

Abstract

We have used the standard channeling technique with a 1.0 MeV He⁺ analyzing beam to investigate the lattice disorder produced in GaAs by 60 keV Cd and 70 keV Zn ion implantations made at room temperature. The amount of disorder produced increases linearly with dose and saturates at a dose of approximately 1–2 × 10¹³ Cd ions/cm². The disorder present in low dose implants (～5 × 10¹² Cd ions/cm²) anneals appreciably by 150 °C. With increasing doses of Cd or Zn the samples show a continuous increase in the anneal temperature required to remove a substantial amount of lattice disorder. There is no apparent difference between the anneal of Zn and Cd implants. The rate at which lattice disorder is produced in GaAs by heavy ion implantations and the doses of heavy ions required to saturate the lattice disorder observed are significantly different from the values of the corresponding quantities for Si and Ge.     

Change of sheet resistance of high purity alumina ceramics implanted by Cu and Ti ions

High purity alumina ceramics (99% Al₂O₃) was implanted by copper ion and titanium ion in a metal vapour vacuum arc (MEVVA) implanter, respectively. The influence of implantation parameters was studied varying ion fluence. The samples were implanted by 68 keV Cu ion and 82 keV Ti ion with fluences from 1 × 10¹⁵ to 1 × 10¹⁸ ions/cm², respectively. The as-implanted samples were investigated by scanning electron microscopy (SEM), glancing X-ray diffraction (GXRD), scanning Auger microscopy (SAM), and four-probe method. Different morphologies were observed on the surfaces of the as-implanted samples and clearly related to implantation parameters. For both ion implantations, the sheet resistances of the alumina samples implanted with Cu and Ti ion fluences of 1 × 10¹⁸ ions/cm², respectively, reached the corresponding minimum values because of the surface metallization. The experimental results indicate that the high-fluence ion implantation resulted in conductive layer on the surface of the as-implanted high purity alumina ceramics.     

Enhanced Upconversion Luminescence of Erbium–Nitrogen-Doped Zinc Oxide Nano-Wires by Implantation of Ytterbium Ions

Erbium–nitrogen codoped zinc oxide nanowires of ytterbium-doped are prepared by thermal evaporation and ion implantation methods. Ytterbium ions are doped into nanowires at a fluence of (0, 1, 3, 5, and 9) × 10¹⁵ cm^?2. Microstructural and optical properties of specimen are investigated by X-ray diffractometer, absorption spectra, Raman, and upconversion photoluminescence examinations. Upconversion photoluminescence emissions at 550 nm and 660 nm are obtained under 980-nm light excitation. Both intensities of green and red peaks are enhanced by the introduction of ytterbium ions. When ytterbium ion fluence is 5 × 10¹⁵ cm^?2, light emission intensity reaches maximum value. The energy transfer and cross-relaxation processes are responsible for the change of emission intensity.     

Au5+ ion implantation induced structural phase transitions probed through structural,microstructural and phonon properties in BiFeO3 ceramics,using synergistic ion beam energy

Implanted Au⁵⁺-ion-induced modification in structural and phonon properties of phase pure BiFeO₃ (BFO) ceramics prepared by sol–gel method was investigated. These BFO samples were implanted by 15.8?MeV ions of Au⁵⁺ at various ion fluence ranging from 1?×?10¹⁴ to 5?×?10¹⁵?ions/cm². Effect of Au⁵⁺ ions’ implantation is explained in terms of structural phase transition coupled with amorphization/recrystallization due to ion implantation probed through XRD, SEM, EDX and Raman spectroscopy. XRD patterns show broad diffuse contributions due to amorphization in implanted samples. SEM images show grains collapsing and mounds’ formation over the surface due to mass transport. The peaks of the Raman spectra were broadened and also the peak intensities were decreased for the samples irradiated with 15.8?MeV Au⁵⁺ ions at a fluence of 5?×?10¹⁵?ion/cm². The percentage increase/decrease in amorphization and recrystallization has been estimated from Raman and XRD data, which support the synergistic effects being operative due to comparable nuclear and electronic energy losses at 15.8?MeV Au⁵⁺ ion implantation. Effect of thermal treatment on implanted samples is also probed and discussed.     

Recrystallization of hexagonal silicon carbide after gold ion irradiation and thermal annealing

Silicon carbide (SiC) single crystals with the 6H polytype structure were irradiated with 4.0-MeV Au ions at room temperature (RT) for increasing fluences ranging from 1?×?10¹² to 2?×?10¹⁵ cm^?2, corresponding to irradiation doses from ~0.03 to 5.3 displacements per atom (dpa). The damage build-up was studied by micro-Raman spectroscopy that shows a progressive amorphization by the decrease and broadening of 6H-SiC lattice phonon peaks and the related growth of bands assigned to Si–Si and C–C homonuclear bonds. A saturation of the lattice damage fraction deduced from Raman spectra is found for ~0.8?dpa (i.e. ion fluence of 3?×?10¹⁴ cm^?2). This process is accompanied by an increase and saturation of the out-of-plane expansion (also for ~0.8?dpa), deduced from the step height at the sample surface, as measured by phase-shift interferometry. Isochronal thermal annealing experiments were then performed on partially amorphous (from 30 to 90%) and fully amorphous samples for temperatures from 200 °C up to 1500 °C under vacuum. Damage recovery and densification take place at the same annealing stage with an onset temperature of ~200 °C. Almost complete 6H polytype regrowth is found for partially amorphous samples (for doses lower than 0.8 dpa) at 1000 °C, whereas a residual damage and swelling remain for larger doses. In the latter case, these unrelaxed internal stresses give rise to an exfoliation process for higher annealing temperatures.     

Structural and Chemical Modification in a Polymer by Metal Ion Implantation

Physical and chemical properties changes in a polymer have been studied for polycarbonate (PC) implanted with 100 keV Ni⁺ ions with varying fluence from 1 × 10¹⁴ to 1 × 10¹⁶ ions/cm². The changes in the surface morphology and composition have been observed with atomic force microscopy (AFM) and X-ray diffraction (XRD). The ions implanted induce changes in topography of PC and indicate that the roughness increases dramatically with ion fluence. Implanted metal ions shows direct evidence of compound formation on the surface. The chemical changes in the surface region have been carried out by Raman Spectroscopy and UV-VIS spectroscopy. UV-VIS absorption analysis indicates a drastic decline in optical band gap from 5.46 eV to 1.76 eV at an implanted dose of 1 × 10¹⁶ ions/cm². It could be shown that the partial destruction of chemical bonding under ion implantation leads to the creation of new amorphous and graphite-like structures, which is confirmed by Raman spectroscopy.     

Modification of the magnetic properties of polyimide films by cobalt ion implantation

The magnetic characteristics of polyimide films implanted with Co⁺ ions with an energy of 40 keV in the dose range D = 2.50 × 10¹⁶?1.25 × 10¹⁷ cm^?2 at ion current densities j = 4, 8, and 12 μA/cm² have been investigated. It has been shown that, at implantation doses of less than 5 × 10¹⁶ cm^?2, the superparamagnetic properties of modified samples are described by the Langevin equation. At higher doses, there is an intercluster interaction. It has been found that, with an increase in the ion current, the cluster size decreases. The sizes of the formed clusters are determined and vary in the range from 3.9 to 11.0 nm, depending on the implantation dose.     

Modifying a cylindrical surface irradiated with a radial beam of argon ions with energies of up to 5 keV

Aspects of the ion modification of the outer surfaces of tubular samples of E110 (Zr–1% Nb) alloy is studied. The samples are irradiated with a radial beam of argon ions (0.5–5.0 keV, (5–10) × 10¹⁸ ion/cm²) on the ILUR-03 setup. It is found that such ion bombardment smooths the relief formed by mechanical abrasive treatment. It is demonstrated that the effect of ion polishing is most pronounced for surface irregularities of a certain size.     

Enhancement in electrochemical properties of ionic liquid-based nanocomposite polymer electrolytes by 100 MeV Si9+ swift heavy ion irradiation

Swift heavy ion (SHI) irradiation has been used as a tool to enhance the electrochemical properties of ionic liquid-based nanocomposite polymer electrolytes dispersed with dedoped polyaniline (PAni) nanorods; 100 MeV Si⁹⁺ ions with four different fluences of 5?×?10¹⁰, 1?×?10¹¹, 5?×?10¹¹, and 1?×?10¹² ions cm^?2 have been used as SHI. XRD results depict that with increasing ion fluence, crystallinity decreases due to chain scission up to fluence of 5?×?10¹¹ ions cm^?2, and at higher fluence, crystallinity increases due to cross-linking of polymer chains. Ionic conductivity, electrochemical stability, and dielectric properties are enhanced with increasing ion fluence attaining maximum value at the fluence of 5?×?10¹¹ ions cm^?2 and subsequently decrease. Optimum ionic conductivity of 1.5?×?10^?2 S cm^?1 and electrochemical stability up to 6.3 V have been obtained at the fluence of 5?×?10¹¹ ions cm^?2. Ac conductivity studies show that ion conduction takes place through hopping of ions from one coordination site to the other. On SHI irradiation, amorphicity of the polymer matrix increases resulting in increased segmental motion which facilitates ion hopping leading to an increase in ionic conductivity. Thermogravimetric analysis (TGA) measurements show that SHI-irradiated nanocomposite polymer electrolytes are thermally stable up to 240–260 °C.     

50 MeV Li3+ ion irradiation effect on structural, electrical, and dielectric properties of PVA-based nanocomposite polymer electrolytes

Nanocomposite polymer electrolyte thin films of polyvinyl alcohol (PVA)-orthophosphoric acid (H₃PO₄)-Al₂O₃ have been prepared by solution cast technique. Films are irradiated with 50 MeV Li³⁺ ions having four different fluences viz. 5?×?10¹⁰, 1?×?10¹¹, 5?×?10¹¹, and 1?×?10¹² ions/cm². The effect of irradiation on polymeric samples has been studied and characterized. X-ray diffraction spectra reveal that percent degree of crystallinity of samples decrease with ion fluences. Glass transition and melting temperatures have been also decreased as observed in differential scanning calorimetry. A possible complexation/interaction has been shown by Fourier transform infrared spectroscopy. Temperature-dependent ionic conductivity shows an Arrhenius behavior before and after glass transition temperature. It is observed that ionic conductivity increases with ion fluences and after a critical fluence, it starts to decrease. Maximum ionic conductivity of ～2.3?×?10^?5 S/cm owing to minimum activation energy of ～0.012 eV has been observed for irradiated electrolyte sample at fluence of 5?×?10¹¹ ions/cm². The dielectric constant and dielectric loss also increase with ion fluences while they decrease with frequency. Transference number of ions shows that the samples are of purely ionic in nature before and after ion irradiation.     

Induced absorption in yttrium aluminium perovskite crystals irradiated by 12C and 235U ions

The present work is devoted to investigation of optical absorption in pure and neodymium-doped YAlO₃ (YAP) single crystals in the spectral range 0.2–1.1 μm induced by the influence of ¹²C ions irradiation with energy 4.50 MeV/u (MeV per nucleon) and a fluence 2 × 10⁹ cm^?2 or of ²³⁵U ion irradiation with energy 9.35 MeV/u and a fluence 5 × 10¹¹ cm^?2. The induced absorption in the case of ¹²C ions irradiation is caused by recharging of point growth defects and impurities under the radiation influence. After irradiation by ²³⁵U ions with fluence 5 × 10¹¹ cm^?2 the strong absorption rise is probably caused by contribution of the lattice destruction as a result of heavy ion bombardment.     

CEMS study on aluminium implanted iron

Up to now a great deal of investigations in ion beam mixing of iron-aluminium layers are known. However, the easier way to produce such layers by direct implantation of aluminium ions in iron is less studied. In the present work aluminium implanted iron layers are studied. Iron samples were implanted with aluminium ions at 50, 100, and 200 keV, respectively, with doses between 5×10¹⁶ and 5×10¹⁷ cm⁻². Independent of energy, at doses up to 2×10¹⁷ cm⁻², besides alpha iron further magnetic fractions with a Fe₃Al-like structure are formed while at a dose of 5×10¹⁷ cm⁻² amorphous nonmagnetic components are formed.     

Combined field ion microscopy and transmission electron microscopy of heavy ion damage in tungsten

Abstract

A field ion microscopy (FIM) and transmission electron microscopy (TEM) investigation of radiation damage in tungsten after heavy ion bombardment has been carried out. Field ion specimens of tungsten were irradiated with 180–230 keV Xe⁺ ions. The irradiation doses were varied between 4 × 10¹¹ and 4 × 10¹² ions/cm². The irradiated specimens were examined in FIM. Experiments combining both TEM and FIM were performed in order to compare the results obtainable by these two methods. The distribution of defects visible by TEM was inhomogeneous. The influence of the imaging field in FIM on the defects visible in TEM is discussed.