并联传感器系统压力传感器故障诊断系统设计

在工业生产过程中电子皮带秤普遍采用多个称重传感器输出信号的并联方法,而该方法对多个称重传感器无法独立采集同时无法准确判断故障。应用TI公司MSC1210单片机最小系统和信号分离器,设计一种并联传感器系统压力传感器故障诊断系统,实现多个称重传感器并联应用时的独立采集;发明一种皮带秤称重传感器累计量校准方法,将不断变化的累计量转换成定量值实现并联传感器系统压力传感器故障诊断。结果表明该系统较好实现多个称重传感器的独立采集和故障传感器判断,为皮带秤等计量装置并联传感器系统的技术升级提供有效手段。     

利用衍射法自动测量金属的弹性模量

采用夫琅禾费衍射原理，发展了一种利用衍射法自动测量金属丝弹性模量的新方法。利用CCD同时获得单缝衍射和单丝衍射图像，编写图像处理程序，对两类衍射条纹进行采集与自动化处理，得到衍射条纹的中央明条纹宽度，分别测量金属丝的微小伸长量和金属丝的直径，从而精确地获得金属丝的弹性模量。衍射法在微小尺度测量上具有较高精度，可用于精确测量金属丝的弹性模量，将光学测量应用于力学量测量，对于培养大学生综合实验技能具有重要作用。     

等倾干涉条纹的采集与处理

迈克尔逊干涉仪是测量微小长度的精密仪器。实验中,测量等倾干涉条纹个数是重要环节。为了实现单片机自动计数,对干涉条纹的采集和处理是前提条件。本文详细介绍了等倾干涉条纹,以及对它的采集与处理方法。     

基于无线通信的接触式带钢板形信号采集系统研制

针对滑环结构的接触式板形测试仪存在的不足,采用无线通信方式,研制了多单片机系统的嵌入式板形信号采集系统,通过光电接近开关的合理安装设计,巧妙解决了检测辊正反转时的信号采集和每组4个传感器信号区分问题,并给出了I2C总线系统中主、从单片机的流程。现场试验表明,在传感器为30组,检测辊10圈/秒转动时,系统的可靠性、数据传输速率和误码率均可满足板形闭环控制的要求。     

获得高质量Moire条纹信号的一种新方法

在细栅距的幅光栅系统中，衍射效应是很明显的，其能量约占总能量的１０～４０％左右，这种衍射光是造成Ｍｏｉｒｅ光电信号对比度不好和正弦性差的根本原因。本文分析了衍射光栅副±１级Ｍｏｉｒｅ条纹的位相关系与光栅副间隙等因素的关系，提出了利用±１级Ｍｏｉｒｅ条纹来获得高质量Ｍｏｉｒｅ条纹信号，实际应用，效果良好。     

基于两步成像的单缝衍射自动测量

建立基于两步成像的单缝衍射自动测量系统,用CCD连续采集成像于旋转白屏的单缝衍射图像,通过衍射图像的平均消除激光散斑的影响;通过分别对零级和非零级条纹成像,解决CCD动态范围较小的问题;用图像处理方法进行条纹水平矫正、极小值位置自动判读,实现单缝宽度自动测量功能.用此系统进行了单缝衍射条纹光强分布及单缝宽度的自动测量实验,相对偏差在2%以内.     

单片机莫尔条纹细分技术

介绍一种软件莫尔条纹细分方法,该方法利用单片机采集数据和数据处理手段细分莫尔条纹信号。该方法测量电路简单,对莫尔条纹信号要求低,细分数高,实时性好,可用于静态、动态测量。     

基于圆衍射条纹的激光准直系统设计

针对高层建筑电梯安装过程中导轨垂直度与平行度的要求,设计了一种新型的激光准直系统。该系统把带有同心圆衍射条纹的准直激光束透射过毛玻璃,用CMOS图像传感器作为接收器,获得准直激光束的光斑图像,由USB接口传输到计算机进行自动处理。基于改进的Hough变换算法,完成了同心圆衍射条纹中心的准实时自动提取,并能跟踪、记录条纹中心的变化轨迹。该系统可以在128mm×96mm的范围内接收准直激光束的圆衍射条纹,条纹中心提取精度在1～2个像素,很好地满足了实际应用的要求。     

测量杨氏模量的智能光电系统

以8051单片机为核心，结合叠栅条纹技术，研制出一种测量杨氏模量的智能光电系统，解决了杨氏模量的高精度测量问题。     

实际光栅系统的分辨本领

本文指出了传统的光栅分辨本领Ｒ＝ｋＮ只是在光源狭缝无限细的情况下的极限值。当光源狭缝还有一定宽度Ｗ时，衍射条纹将增宽，相应最小分辨角Δθｋ将增大，实际光栅系统的分辨本领将减小。文章运用衍射理论，给出了实际光栅系统分辨本领的修正公式。在实验中，在不同光栅宽度Ｄ的情况下，用ｋ＝１级衍射条纹，当测量恰能分辨钠黄光的双线结构的光源缝宽Ｗ时，这时光栅系统的分辨本领是λ／δλ≈１０００，与修正公式计算的理论值一致。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.     

Direction-of-arrival estimation using matrix spatial prefiltering approach

An approach to direction-of-arrival （DOA） estimation for multiple narrowband farfield signals is proposed. The technique uses a novel matrix spatial prefiltering approach. Specifically, a matrix filter is designed to spatially filter the incoming data snapshots. The un-wanted components arriving from the stopband angular sectors are attenuated and the desired components from the angular sector of interest pass with minimal distortion. The matrix filter spatially filters the element-space data and the output reserves the element-space data property, which makes it very useful by passing sensor data through a spatial prefilter prior to applying many other array processors to attenuate interferences and improve system performance. Several examples of DOA estimation problem are presented to illustrate the performance of the proposed spatial prefiltering approach. Results of simulation and real data show that the pre-filter can efficiently attenuate the spatial interferences and significantly improve the estimation and resolution capability of DOA estimators at low signal-to-noise ratios for the sources located inside the passband sector. In addition, the use of spatial prefilter makes it possible to estimate DOAs for multiple sources more than the number of the elements of an array.     

Quantum efficiency calibration of opto-electronic detector by means of correlated photons method

A new calibration method of detectors can be realized by using correlated photons generated in spontaneous parametric down-conversion (SPDC) effect of nonlinear crystal.An absolute calibration system of detector quantum efficiency is performed.And its principle and experimental setup are introduced.A continuouswave (CW) ultraviolet (351 nm),diode-pumped,frequency-doubled,and solid-state laser is used to pump BBO crystal.The quantum efficiencies of the photomultiplier at 633,702,and 789 nm are measured respectively.The coincidence peaks are observed using coincidence circuit.Some measurement factors including the filter bandwidth of trigger channel,the detector position alignment and polarization of the pump light are analyzed.The uncertainties of this calibration method are also analyzed,and the relative uncertainties of total calibration are less than 5.8%.The accuracy of this method could be improved in the future.