Sol-gel synthesis of sub-50 nm ZnO nanowires on pulse laser deposited ZnO thin films

A simple synthesis route to high-quality sub-50 nm ZnO nanowires is reported, utilizing ZnO thin films grown by pulse laser deposition (PLD) as seed layers. Depending upon the PLD growth conditions, the surface morphology of the ZnO nanowires on ZnO film was distinctively different whereas the diameters were almost the same. With the increase of the concentration of zinc nitrate/methenamine solution from 0.002 to 0.02 M, the average diameter of the ZnO nanowire increased but remained sub-50 nm. The grown ZnO nanowires showed a high crystallinity with a low defect density confirmed by a sharp photoluminescence spectrum.     

Study of the morphological evolution of ZnO nanostructures on various sapphire substrates

Zinc oxide (ZnO) nanostructures were grown on A-, C- and R-plane sapphires by metal organic chemical vapor deposition (MOCVD) technique. The shape of nanostructures was greatly influenced by the underlying sapphire substrate. Vertical aligned nanowires were observed on A- and C-plane sapphires, whereas the nanopencils were grown on R-plane sapphire. A correlation between the morphological and optical properties of the nanostructures has been established, where the morphological and structural characteristics are responsible for the evolution of optical properties. The nanowires, grown on C-plane sapphires, have shown superior optical properties. Comparatively higher photo-induced wettability transition has also been observed for ZnO nanostructures on R-plane sapphire.     

Effect of sputtered films on morphology of vertical aligned ZnO nanowires

Vertical aligned ZnO nanowires were grown by MOCVD technique on silicon substrate using ZnO and AlN thin films as seed layers. The shape of nanostructures was greatly influenced by the under laying surface. Vertical nanopencils were observed on ZnO/Si, whereas the nanowires on both sapphire and AlN/Si substrate have the similar aspect ratio. XRD patterns suggest that the nanostructures have good crystallinity. High-resolution transmission electron microscopy (HRTEM) confirmed the single crystalline growth of the ZnO nanowires along [0 0 1] direction. Room-temperature photoluminescence (PL) spectra of ZnO nanowires on AlN/Si clearly show a band-edge luminescence accompanied with a visible emission. More interestingly, no visible emission for the nanopencils on ZnO/Si substrates, were observed.     

Fabrication of ZnO nanostructures of various dimensions using patterned substrates

ZnO nanostructures were grown on silicon, porous silicon, ZnO/Si and AlN/Si substrates by low-temperature aqueous synthesis method. The shape of nanostructures greatly depends on the underlying surface. Scattered ZnO nanorods were observed on silicon substrate, whereas aligned ZnO nanowires were obtained by introducing sputtered ZnO film as a seed layer. Furthermore, both the combination of nanorods and the bunch of nanowires were found on porous silicon substrates, whereas platelet-like morphology was observed on AlN/Si substrates. XRD patterns suggest the crystalline nature of aqueous-grown ZnO nanostructures and high-resolution transmission electron microscopy images confirm the single-crystalline growth of the ZnO nanorods along [0 0 1] direction. Room-temperature photoluminescence characterization clearly shows a band-edge luminescence along with a visible luminescence in the yellow spectral range.     

Growth, modulation and photoresponse characteristics of vertically aligned ZnO nanowires

Vertically aligned, c-axis oriented zinc oxide (ZnO) nanowires were grown on Si substrate by metal organic chemical vapor deposition (MOCVD) technique, where sputtered aluminum nitride (AlN) film was used as an intermediate layer and thermally evaporated barium fluoride (BaF₂) film as a sacrificial layer. The aspect ratio and density of the nanowires were also varied using only Si microcavity without any interfacial or sacrificial layer. The UV detectors inside the microcavity have shown the higher on-off current ratio and fast photoresponse characteristics. The photoresponse characteristics were significantly varied with the aspect ratio and the density of nanowires.     

Synthesis of ZnO nanowires by pulsed laser deposition in furnace

ZnO nanowires were fabricated on Au coated (0 0 0 1) sapphire substrates by using a pulsed Nd:YAG laser with a ZnO target in furnace. ZnO nanowires have various sizes and shapes with a different substrate position inside a furnace. The length and the diameter of these ZnO nanowires were around 3-4 μm and 120-200 nm, respectively, confirmed by scanning electron microscopy (SEM). The diameter control of the nanowires was achieved by varying the position of substrates. The ultraviolet emission of nanowires from the near band-edge emission (NBE) was observed at room temperature. The formation mechanism and the effect of different position of substrates on the structural and optical properties of ZnO nanowires are discussed.     

Effects of sapphire substrate annealing on ZnO epitaxial films grown by MOCVD

The annealing effects of sapphire substrate on the quality of epitaxial ZnO films grown by metalorganic chemical vapor deposition (MOCVD) were studied. The atomic steps formed on (0 0 0 1) sapphire (α-Al₂O₃) substrate surface by annealing at high temperature was analyzed by atomic force microscopy (AFM). The annealing effects of sapphire substrate on the ZnO films were examined by X-ray diffraction (XRD), AFM and photoluminescence (PL) measurements. Experimental results indicate that the film quality is strongly affected by annealing treatment of the sapphire substrate surface. The optimum annealing temperature of sapphire substrates is given.     

Epitaxial ZnO films grown on ZnO-buffered c-plane sapphire substrates by hydrothermal method

ZnO films are hydrothermally grown on ZnO-buffered c-plane sapphire substrates at a low temperature of 70 °C. A radio-frequency (RF) reactive magnetron sputtering has been used to grow the ZnO buffer layers. X-ray diffraction, scanning electron microscopy, and room temperature photoluminescence are carried out to characterize the structure, morphology and optical property of the films. It is found that the films are stress-free. The epitaxial relationship between the ZnO film and the c-plane sapphire substrate is found to be ZnO (0 0 0 1)||Al₂O₃ (0 0 0 1) in the surface normal and in plane. Sapphire treatment, as such acid etching, nitridation, and oxidation are found to influence the nucleation of the film growth, and the buffer layers determine the crystalline quality of the ZnO films. The maximum PL quantum efficiency of ZnO films grown with hydrothermal method is found to be about 80% of single-crystal ZnO.     

Growth and characterization of type-II ZnO/ZnTe core-shell nanowire arrays for solar cell applications

Large area, well-aligned type-II ZnO/ZnTe core-shell nanowire arrays have been fabricated on an a-plane sapphire substrate. The ZnO nanowires were grown in a furnace by chemical vapor deposition with gold as catalyst and then were coated with a ZnTe shell on the ZnO nanowires surface by a metal-organic chemical deposition chamber. The morphology and size distribution of the ZnO/ZnTe core-shell nanowire arrays were studied by scanning electron microscopy (SEM) and the crystal structure was examined by x-ray diffraction (XRD). Transmission measurement was used to study the optical properties of the core-shell nanowires. The results indicated that the ZnO/ZnTe core-shell nanowire arrays have good crystalline quality. In addition, it was found that the nanowire arrays have good light absorption characteristics and these properties make it suitable for making photovoltaic devices.     

Photoluminescence from amorphous silica nanowires synthesized using TiN/Ni/SiO2/Si and TiN/Ni/Si substrates

Photoluminescence characteristics of amorphous silica nanowires (a-SiONWs) grown on TiN/Ni/Si and TiN/Ni/SiO₂ substrates have been studied. A-SiONWs grown on TiN/Ni/Si substrates show a Si-rich composition compared to those grown from TiN/Ni/SiO₂/Si. The emission characteristics of the nanowires were found to depend on the type of substrate. By annealing the a-SiONWs grown on TiN/Ni/Si in air, emission bands shift from blue to green bands. It is likely that silicon to oxygen ratio is an important factor in deciding the types of defects and emission bands of amorphous silica nanowires.     

Catalyst-free synthesis of novel brush-shaped ZnO particles by a simple oxidation in air

Brush-shaped ZnO particles were synthesized by controlling the growth time in the direct melt oxidation process of Al-Zn mixture in air at atmospheric pressure. Particles with two kinds of structures were formed. One was consisted of nanowires grown along [0 0 0 1] direction at the six corners and the center of (0 0 0 1) basal plane on hexagonal ZnO microrod. The other was constructed by nanobelts between the corner-nanowires as well as nanowires at the corners on ZnO microrod. The structural configuration that the nanowires and the nanobelts have a well coherent orientation alignment with the base microrod implies that the brush-shaped ZnO is single crystal. Room temperature PL spectrum of the brush-shaped ZnO particles displayed predominant green emission with a wavelength of 510 nm.     

Post-deposition atomic terraces growth of ZnO thin films deposited on epi-GaN templates

We demonstrate how growth processes affect on ZnO film properties, which are to be essential guides to prevent defect formation in order to synthesize reproducible high quality ZnO films. First, we reveal that deposition at a low temperature is indispensable to transfer underlying GaN atomic terraces to ZnO surface. As the film thickness is increased, however, the terraces disappear to develop island morphology. It is found that the thick film surface is smoothed to the extent that atomic terraces can be seen after an appropriate thermal treatment. Adverse effects associated with high annealing temperatures are then demonstrated as evidenced by cracks formation, increased yellow cathode-luminescence and intermixing at the interface.     

Aligned growth of ZnO nanowires by NAPLD and their optical characterizations

Not only vertically aligned ZnO nanowires but also horizontally aligned ZnO nanowires have been successfully grown on the annealed (0 0 0 1) c-cut and (1 1 2 0) a-cut sapphire substrates, respectively using catalyst-free nanoparticle-assisted pulsed-laser ablation deposition (NAPLD). The as-synthesized ZnO nanowires exhibit an ultraviolet emission at around 390 nm and the absent green emission under room temperature. The single ZnO nanowire was collected in the electrode gap by dielectrophoresis (DEP). Under the optical pumping, the single ZnO nanowire exhibited UV emission at around 390 nm with several sharp peaks whose energy spacings are almost constant, which greatly differs from the broad UV emission of the film with many nanowires, suggesting ZnO nanowires as candidates for laser media. The single ZnO nanowire showed polarized photoluminescence (PL). The as-synthesized ZnO nanowires could find many interesting applications in short-wavelength light-emitting diode (LED), laser diode and gas sensor.     

Electroluminescence from ZnO nanowire-based p-GaN/n-ZnO heterojunction light-emitting diodes

Vertically aligned ZnO nanowires were successfully grown on the sapphire substrate by nanoparticle-assisted pulsed laser deposition (NAPLD), which were employed in fabricating the ZnO nanowire-based heterojunction structures. p-GaN/n-ZnO heterojunction light-emitting diodes (LEDs) with embedded ZnO nanowires were obtained by fabricating p-GaN:Mg film/ZnO nanowire/n-ZnO film structures. The current–voltage measurements showed a typical diode characteristic with a threshold voltage of about 2.5 V. Electroluminescence (EL) emission having the wavelength of about 380 nm was observed under forward bias in the heterojunction diodes and was intensified by increasing the applied voltage up to 30 V.     

Influence of substrate temperature on the optical and piezoelectric properties of ZnO thin films deposited by rf magnetron sputtering

In this study, ZnO thin films were fabricated using the rf magnetron sputtering method and their piezoelectrical and optical characteristics were investigated for various substrate temperatures. The ZnO thin film has the largest crystallization orientation for the (0 0 2) peak and the smallest FWHM value of 0.56° at a substrate temperature of 200 °C. The surface morphology shows a relatively dense surface structure at 200 °C compared to the other substrate temperatures. The surface roughness shows the smallest of 1.6 nm at a substrate temperature of 200 °C. The piezoelectric constant of the ZnO thin film measured using the pneumatic loading method (PLM) has a maximum value of 11.9 pC/N at a substrate temperature of 200 °C. The transmittance of the ZnO thin film measured using spectrophotometry with various substrate temperatures ranged from 75 to 93% in the visible light region. By fitting the refractive index from the transmittance to the Sellmeir dispersion relation, we can predict the refractive index of the ZnO thin film according to the wavelength. In the visible light range, the refraction index of the ZnO thin film deposited at a substrate temperature of 200 °C is the range of 1.88-2.08.     

Epitaxially grown ZnO thin films on 6H-SiC(0 0 0 1) substrates prepared by spin coating-pyrolysis

Epitaxially grown ZnO thin film on 6H-SiC(0 0 0 1) substrate was prepared by using a spin coating-pyrolysis with a zinc naphthenate precursor. As-deposited film was pyrolyzed at 500 °C for 10 min in air and finally annealed at 800 °C for 30 min in air. In-plane alignment of the film was investigated by X-ray pole-figure analysis. Field emission-scanning electron microscope, scanning probe microscope, and He-Cd laser (325 nm) was used to analyze the surface morphology, the surface roughness and photoluminescence of the films. In the photoluminescence spectra, near-band-edge emission with a broad deep-level emission was observed. The position of the near-band-edge peak was around 3.27 eV.     

Electron transport in high quality undoped ZnO film grown by plasma-assisted molecular beam epitaxy

High quality ZnO films were grown on c-plane sapphire substrate using low temperature ZnO buffer layer by plasma-assisted molecular beam epitaxy. The film deposited at 720 °C showed the lowest value of full-width at half maximum for the symmetric (0002) diffraction peak of about 86 arcsec. The highest electron mobility in the films was about 103-105 cm²/V s. From temperature-dependent Hall effect measurements, the mobility strongly depends on the dislocation density at low temperature region and the polar optical phonon scattering at high temperature, respectively. Moreover, by obtaining the activation energy of the shallow donors, it was supposed that hydrogen was source of n-type conductivity in as-grown ZnO films.     

Non-catalytic growth of high aspect-ratio ZnO nanowires by thermal evaporation

High-density and high aspect-ratio ZnO nanowires were grown on Si(100) substrates by the thermal evaporation of metallic zinc powder without the use of metal catalysts or additives. The as-grown nanowires had diameters in the range of 60-100 nm with lengths 5-15 μm. Detailed structural characterization indicated that the obtained nanowires are single-crystalline with a perfect hexagonal facet and surfaces. The room temperature PL spectrum exhibited strong UV emission, affirming that the as-grown products have good optical properties. The possible growth mechanism for the formation of hexagonal-faceted and perfect surface ZnO nanowires is also discussed.     

Regrowth of ZnO thin film with high surface flatness and enhanced optical properties on annealed buffer layers by rf sputtering deposition

We report a study on improving the surface flatness, optical properties, and crystallinity of ZnO thin films by rf sputtering deposition. ZnO thin films grown on sapphire substrate were first exposed to post-growth annealing, and then used to regrow high-quality ZnO thin films on top. Under the same deposition conditions, the regrown ZnO layers showed much improved crystallinity, surface flatness and enhanced optical properties. The effect of the annealed layer in improving the quality of the ZnO thin film is discussed in terms of characterization results from crystal orientation, surface morphology, and photoluminescence. It was clearly observed that, during the annealing process, the ZnO grains coalesced to form larger grains and smoother surfaces, with better crystallinity and fewer defects, which resulted in the much improved quality of the regrown ZnO thin films.     

Influence of Sb on a controlled-growth of aligned ZnO nanowires in nanoparticle-assisted pulsed-laser deposition

Single-crystalline ZnO nanowires on a sapphire substrate have been synthesized by a nanoparticle-assisted pulsed-laser deposition (NAPLD) using a pure and Sb₂O₃ doped ZnO target. Low density and vertically well-aligned ZnO nanowires were grown on hexagonal cone-shape ZnO cores by introduction of a ZnO buffer layer. More than 90% of the ZnO cores of the Sb-induced ZnO nanowires are formed in the same size of 400 nm. The ZnO nanowires consist of single-crystalline wurtzite ZnO crystal and grow along [0001] direction. The room-temperature photoluminescence spectrum exhibited a strong ultraviolet emission at around 380 nm and a relatively low broad band emission in the visible region, indicating a low concentration of structural defect in the nanowires. Sb can be used as one of the effective additives to control the morphology and alignment of ZnO nanowires synthesized by NAPLD.