基于拉锥光纤布拉格光栅的法布里-珀罗应变传感器的仿真研究

为解决干涉型光纤应变传感器自由光谱范围较小或干涉条纹精细度较低等问题，提出了一种基于单拉锥光纤布拉格光栅的法布里-珀罗腔的应变传感结构及其改进方案。利用啁啾光纤布拉格光栅不同位置反射不同波长的特性，形成腔长随波长连续变化的法布里-珀罗腔，得到了无穷大的自由光谱范围且谐振谷精细度高。数值计算结果表明，应变传感灵敏度与拉锥光纤的腰区直径和栅区长度正相关。在0～300 με范围内，当腰区直径为光纤直径的3/25，栅区长度为30 mm时，应变传感灵敏度为7.05 pm/με。该结果对其他干涉型传感结构的设计具有一定的参考价值。     

Mach-Zehnder all-fiber interferometer using two in-series fattened fiber gratings

We present an all-fiber Mach-Zehnder interferometer consisting of two consecutive fattened sections of dispersion-shifted fiber that act as in-series long period fiber gratings. The proposed Mach-Zehnder interferometer shows a broad fringe pattern ranging from 1000 to 1500 nm and is stable against changes in temperature and strain. By tapering a section of 5mm in length to 50% diameter between the fattened sections we observe an increased sensitivity to temperature changes. The measured temperature and strain sensitivities were in the range of 9–17 pm/°C and 1.44–2.9 pm/μɛ, respectively.     

Characteristics of supercontinuum generationin tapered fibers using femtosecond laser pulses

Drawing single mode fibers over a flame generates tapered fibers with waist diameters of approximately 1–3 micrometers and waist lengths of up to 90?mm. We demonstrate how the profile of such tapered fibers can be determined. We then characterize the white light that is generated in a variety of such fibers, showing its dependence on waist length and waist diameter and demonstrating its dependence on pulse parameters such as pulse duration, spectral position, and pulse power. A comparison with theoretical calculations using a nonlinear Schrödinger equation model including Kerr nonlinearities is given. Furthermore, we show XFROG spectrograms of the pulses propagating through tapered fibers, confirming the model of soliton splitting in the anomalous dispersion regime.     

Ultra-longer fiber cantilever taper for simultaneous measurement of temperature and relative humidity

An ultra-longer fiber cantilever taper for simultaneous measurement of the temperature and relative humidity (RH) with high sensitivities was proposed. The structure was fabricated by using the simple and cost-effective method only including fiber cleaving, splicing, and tapering. The length of the cantilever taper is about 1.5 mm. The dip A and dip B were measured simultaneously, owing to the ultra-long length and super-fine size, the temperature sensitivities of the dip A and dip B reached as high as 127.3 pm/℃ and 0 pm/℃ between 25 ℃ and 50 ℃, and the RH sensitivities are -31.2 pm/% RH and -29.2 pm/% RH with a broad RH interval ranging from 20% RH to 70% RH. Besides, the proposed structure showed good linearity in the sensing process and small temperature crosstalk. It will be found in wide applications in environmental monitoring, food processing, and industries.     

飞秒泵浦不同锥长微结构光纤超连续谱的产生

对飞秒脉冲泵浦下,不同锥长及锥腰直径的微结构光纤的超连续谱产生进行了实验研究。采用“快速低温拉锥方法”,在保持d/Λ不变的情况下,对实验室自制的空气孔间距Λ=6.53 μm,归一化孔径d/Λ=0.79的微结构光纤进行了拉锥,分别得到6,8,10 mm等不同锥长微结构光纤。理论计算表明,随着锥长变长,锥腰直径变小,锥腰处零色散波长向短波移动：未拉锥及6,8和10 mm锥微结构光纤锥腰处零色散波长分别为1 129,885,806和637 nm。利用中心波长为810 nm,重复频率76 MHz,脉宽120 fs的钛蓝宝石飞秒激光器对拉锥后微结构光纤进行了实验研究：锥长为6 mm时,泵浦光中心波长位于整根光纤的正常色散区,锥腰的零色散点附近,内脉冲拉曼散射和级联四波混频是光谱初始展宽的主要因素。泵浦功率达到450 mW时,在可见波段390～461 nm及红外波段1 134～1 512 nm形成-5 dB的平坦宽带连续光谱。泵浦功率达到500 mW时,出现366～2 450 nm覆盖紫外、可见、近红外、中红外的超连续谱,其光谱红蓝移边缘已经接近实验用微结构光纤的传输带宽。锥长为8 mm、泵浦功率为450 mW时,在群速度匹配和群加速度失配的共同影响下,连续谱蓝移边缘达到366 nm,比6 mm锥时蓝移9 nm;锥长为10 mm时,由于锥腰处零色散点移动到可见光区域,可见区光谱仍能满足相位匹配条件。通过级联四波混频效应,在可见区域实现了频率上转换及光谱蓝移。泵浦光功率达到500 mW时,在382～412 nm得到谱宽仅为30 nm,转换效率达到27.7%的频率上转换。     

超连续谱光纤合束器的数值模拟

设计了一种用于超连续谱合束的光纤合束器,这种合束器通过将多路光子晶体光纤拉锥后对接到一路多模光纤制成。借助有限差分波束传输法对该合束器进行了数值模拟,结果表明拉锥过渡长度和拉锥比例对耦合损耗具有较大影响,当拉锥过渡长度小于拉锥衍射长度时合束器有较大传输损耗,而过渡长度足够大以及拉锥比例较小时,合束器具有较低的耦合损耗以及优良的宽光谱耦合特性。所得出的数值结果为光子晶体光纤拉锥和超连续谱光纤合束器研制提供了一定的参考依据。     

熔锥型微纳光纤耦合器的理论与实验研究

针对熔融拉锥系统制得的熔锥型微纳光纤耦合器,选择适当的连续函数描述其光场分布,采用归一化的三角分布和矩形分布的加权叠加,以及高斯分布和三角分布的加权叠加实现了模场沿耦合器区域的连续变化;利用局部模式耦合理论推导出腰区及腰区附近锥形区的耦合系数计算公式,并得到微纳光纤耦合器输出光功率随拉伸长度的变化曲线.计算结果表明,随着拉伸长度的增加,光能量在两臂中来回交替耦合的程度变小并且呈现包络样,直至腰区耦合功能消失.通过实时监测拉制微纳光纤耦合器的输出光功率,得到火焰扫描宽度以及氢气流量对双纤失去耦合效应拉伸长度的影响:火焰扫描宽度(均匀腰区)越宽,拉伸长度临界值越大;氢气流量(熔融度)越大,拉伸长度临界值越小.实验结果显示,当光纤耦合器腰区直径达到1.6μm时,耦合功能消失,两输出端口光功率相同且恒定,微纳光纤耦合器具备稳定的光学传输特性.     

Spectral superbroadening of subnanojoule Cr:Forsterite femtosecond laser pulses in a tapered fiber

Spectral superbroadening of subnanojoule femtosecond Cr:forsterite laser pulses is demonstrated for the first time in experiments with a tapered fiber. Coupling 40-fs 0.6-nJ pulses of 1.25-μm Cr:forsterite laser radiation into a tapered fiber with a taper waist diameter of about 2 μm and a taper waist length of 90 mm, we observed the spectra spanning more than two octaves at the output of the fiber. These experimental results open new horizons for the creation of compact femtosecond systems based on Cr:forsterite lasers and tapered fibers for optical metrology and biomedical applications.     

Two-octave spectral broadening of subnanojoule Cr:forsterite femtosecond laser pulses in tapered fibers

Spectral broadening of femtosecond Cr:forsterite laser pulses is enhanced due to the use of tapered fibers. Supercontinuum generation with unamplified subnanojoule femtosecond Cr:forsterite laser pulses is observed for the first time. With 40-fs 0.6-nJ pulses of 1.25-μm Cr:forsterite laser radiation coupled into a tapered fiber having a taper waist diameter of about 2 μm and a taper waist length of 90 mm, we observed the spectra spanning more than two octaves at the output of the fiber in the regime of anomalous group-velocity dispersion. This result opens the way for the creation of compact femtosecond Cr:forsterite laser plus tapered fiber systems for optical metrology and biomedical applications. Received: 23 October 2001 / Accepted: 16 January 2002 / Published online: 14 March 2002     

Temperature compensation of multimode-interference-based fiber devices

Single-mode-multimode-single-mode (SMS) fiber structures have been demonstrated to be a simple and effective way to realize multimode interference (MMI) in optical fibers. The temperature dependence of the spectral characteristics of SMS devices is investigated. By utilizing the feature that the response spectra of SMS devices with opposite polarities to temperature and axial tensile strain, I demonstrate that temperature compensation of SMS devices can be realized by using materials with a proper coefficient of thermal expansion. A temperature stability of 1.0 pm/ degrees C has been experimentally demonstrated with a ceramic as the packaging material.     

Spatial optical filter sensor based on hollow-core silica tube

A spatial optical filter based on a hollow-core silica tube is proposed. Because of the hollow-core dimensions, it is possible to obtain a periodical spatial filter ranging from 1200 to 1700 nm with a channel spacing of 2.64 THz. The bandwidth is approximately 5.32 nm, and the isolation loss is ~30 dB. The optical losses are approximately ~0.67 dB/mm for a wavelength of 1500 nm. The 40 mm long spatial optical filter is tested as a sensing element and subjected to different physical parameters. The spatial optical filter is wavelength sensitive to strain and temperature, while for refractive-index variations there is an optical power dependency. This fiber structure can be used as a sensing element for extreme conditions, such as in very high temperature environments, where it presents a sensitivity of 27.5 pm °C(-1).     

光纤布拉格光栅嵌入SMS光纤结构的湿度传感器

提出了一种基于光纤布拉格光栅嵌入单模-多模纤芯-单模(single-mode-multimode fiber core-single mode, SMS)光纤结构的湿度传感器。当环境湿度变化时,SMS光纤结构的干涉光谱会发生漂移,而光纤布拉格光栅对湿度不敏感,其纤芯基模保持不变。因此利用SMS光纤结构对环境湿度的敏感性去调制光纤布拉格光栅纤芯基模,通过检测光纤布拉格光栅纤芯基模的反射能量变化就可以实现湿度测量。数值模拟了SMS光纤结构的内部光场分布规律,理论计算了不同环境折射率时,多模纤芯的长度、直径对SMS光纤结构输出能量耦合系数的影响。理论模拟表明,随着环境折射率变化,SMS光纤结构中传输的纤芯基模的输出能量耦合系数会发生变化。同时制作了传感器样品并对其进行了传感实验研究,实验结果表明多模纤芯长35 mm、纤芯直径为85 μm的传感器在45%～95%RH湿度变化范围内,湿度灵敏度为0.06 dBm·(%RH)-1。在20～80 ℃温度范围内,传感器的温度灵敏度为0.008 nm·℃-1,温度所带来的湿度测量误差为0.047%RH·℃-1。传感器具有制作简单、灵敏度高、反射式能量检测等优点,在湿度测量领域有一定的应用价值。     

Single S-tapered fiber Mach-Zehnder interferometers

A fiber Mach-Zehnder interferometer (MZI) sensor, novel to our knowledge, based on a single "S"-like fiber taper has been fabricated via applying nonaxial pull in fiber tapering by a fusion splicer. The typical feature size of the structure has a length of 660 μm and the axial offset of 96 μm. This S fiber taper MZI has a refractive index (RI) sensitivity of 1590 nm/refractive index unit in the RI range of 1.409-1.425 and a strain sensitivity of about -60 pm/microstrain, which is 30 times higher than that of the normal two-taper-based MZI sensors.     

新型缓变锥型PCF结构接口耦合损耗特性

提出一种新型的缓变锥型光纤接口器件。该接口器件是一个长度为150mm左右的缓变锥型光子晶体光纤。利用有限元方法对模场直径差别较大的不同光纤进行拼接时的损耗问题进行研究。研究结果表明:在模场直径分别为9μm和10.4μm的光纤之间加入锥型光纤后可以有效降低耦合损耗,并且在不同波长下耦合损耗都维持在一个较低水平。因此,该接口器件能够实现光纤拼接时物理结构的过渡和不同模场直径的转换,从而使拼接损耗降到最低。     

Visible supercontinuum generation in tapered photonic crystal fiber pumped by picosecond pulse at 1064 nm

Short photonic crystal fibers (PCFs) with different tapered waist diameter are made to extend the continuum spectrum in the visible range. The diversification of output continuum spectrum with the diameter of the tapered waist is experimentally observed. An all fiber visible supercontinuum source with 1.88 W output is demonstrated in our experiments. To the best of our knowledge, it is the highest all fiber visible supercontinuum generation in tapered PCF, pumping by picosecond pulse at 1064 nm. The suitably designed short tapered PCF can extend the visible spectrum, while, how to preserve the tapered waist is crucial for the all fiber visible supercontinuum source in the practical applications.     

Tunable laser generation with erbium-doped microfiber knot resonator

A tunable laser is demonstrated using a microfiber knot resonator structure made by erbiumdoped fiber (EDF). The laser is made of a 2 m long EDF where 30 mm of its end section is tapered to construct a microfiber knot resonator (MKR). The combination of the EDF and MKR generates a stable single wavelength laser at 1555 nm wavelength with a signal to noise ratio (SNR) of 33.7 dB using a 63 mW of 980 nm pump power. The peak wavelength of the laser can be tuned by 340 pm as the MKR diameter reduces from 5.0 to 0.5 mm with an acceptable penalty in output power.     

Self tapering and uptapering of a self guided laser beam in an absorbing/gain medium with nonlinearity

The absorption/gain induced self tapering and uptapering of a self guided Gaussian laser beam when the beam propagates in a saturable nonlinear medium has been discussed. Using the WKBJ and abberationless paraxial ray approximation a beam width equation has been derived. Conditions for tapering/uptapering for both cases i.e., for absorption and gain have been discussed. The beam width of tapered/uptapered beam depends on the rate of absorption/gain, and the length of absorption/gain region along the beam propagation direction. The importance of the present study is pointed out.     

Broadband second harmonic generation in a tapered isotropic semiconductor slab using total internal reflection quasi phase matching

This paper analytically describes the concept of enhancing the bandwidth of second-harmonic generation in the mid-infrared region in an isotropic tapered semiconductor slab configuration. In this slab geometry, the lengths between successive reflection points due to total internal reflection of the incident laser radiation increase when it propagates through the slab. A computer aided simulation has been carried out to determine the possibility of generating broadband second harmonic intensity for broadband fundamental laser radiations as they are allowed to undergo total internal reflection inside the tapered isotropic semiconductor crystal slab made of either gallium arsenide (GaAs) or zinc selenide (ZnSe). The simulated results indicate wide 3 dB bandwidths of 187 nm and 196 nm in a 30 mm long tapered slab of GaAs and ZnSe respectively. The conversion efficiency, after considering the absorption and reflection losses, is quite satisfactory (≈ 1%). The effects of variations in temperature, incident angle of the fundamental laser radiations at the air-slab interface, length and tapering angle of the semiconductor slab have been studied for generated second harmonic radiations in both GaAs and ZnSe crystals. Optimising these parameters a wider broadband frequency converter with appreciable conversion efficiency can be designed.     

一种单模-多模-单模结构的干涉型光纤温度传感器

SMS光纤结构是一种近年来新兴的光纤器件,该结构光纤具有结构简单、易于实现、成本低廉、灵敏度高和无温度应力交叉敏感等特性.在光纤传感技术领域是一种继光纤光栅之后的具有广泛发展前景的光纤器件.从理论上分析了SMS结构和SMS级联结构的光纤传感原理,并从实验上研究了SMS结构和级联SMS结构的温度传感特性.实验表明:对于SMS结构光纤传感器,随着温度的增加,特征波长移动量逐渐增加,向长波方向漂移了4.05 nm,其传感器的温度灵敏度为15.76 pm/℃;对于级联SMS结构的光纤传感器,级联后不改变原来SMS结构的中心波长的位置,两个SMS结构仍然是独立的,不相互影响.所以说将两个SMS结构串联是可行的,可以用于温度和应力的同时测量,也可以用于分布式光纤传感器.     

Ultrastructure and morphometry of the egg of Psorophora albigenu Lutz, 1908 (Diptera: Culicidae)

Eggs of Psorophora albigenu were analyzed by light and scanning electron microscopy. Eggs were laid singly and were black and elliptical in outline. A length of approximately 586.4 ± 10.83 μm, a width of 172.3 ± 8.09 μm (n=30), and an egg index (length/width ratio) of 3.33 were observed. The anterior extremity tapered abruptly from a width of 64.9 μm, while such tapering was more gradual at the posterior extremity from a width of 77.4 μm. The ventral surface of the chorionic coating presented cells with tubular aspect containing tubercles in rows with a density of 9-16 tubercles per cell. These tubercles presented two different sizes, with the largest measuring 7.87 ± 01.58 μm and the smallest measuring 0.71 ± 0.53 μm (n=30) in longitudinal diameter. The micropyle orifice was very evident, with a diameter of 3.36 μm. The morphometric characteristics of Ps. albigenu obtained in this study were distinct from those of other species of the Psorophora genus, including Psorophora varipes which has been considered for a long time to be synonymous with Ps. albigenu.