Polypropylene surface modification by entrapment of polypropylene-graft-poly(butyl methacrylate)

Surface modification of polypropylene was carried out by entraping a copolymer of polypropylene grafted poly(butyl methacrylate) into polypropylene. The effects of structure of copolymers, contact die and content of modifiers on their surface enrichment were studied by attenuated total reflection infrared spectroscopy (ATR-FTIR), contact angle measurements and scanning electron microscopy (SEM). The results indicated that PPw-g-PBMA could diffuse preferably onto the surface and effectively increase the hydrophilicity of PP. Lower content and higher surface energy die were in favor of the copolymer to enrich on the PP surface. PPw-g-PBMA with low PBMA contents, short length of PBMA distributed in PP with smaller phase domains and favored its selective enrichment on the surface of PP, especially at lower loadings in blends. The modified material exhibited excellent solvent-resistance.     

Surface modification of polypropylene and compatibilization of interfaces in incompatible blends of polypropylene with polystyrene by plasma of CO2

The effect of surface modification of polypropylene (PP) film is induced by CO₂ plasma in this study. The change in chemical structures on the surface of PP film is characterized by X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FT-IR). The polarity of modified surface of PP film is investigated by contact angle method. The compatibilization of interfaces between polypropylene and polystyrene phases in incompatible blends is studied by the treatment of plasma of CO₂. Transition layer thickness is measured by small angle light scattering (SALS).     

Surface modification of polypropylene non-woven fabric using atmospheric nitrogen dielectric barrier discharge plasma

In this paper, a dielectric barrier discharge operating in nitrogen at atmospheric pressure has been used to improve the surface hydrophilic property of polypropylene (PP) non-woven fabric. The changes in the hydrophilic property of the modified PP samples are investigated by the contact angle measurements and the variation of water contact angle is obtained as a function of the energy density; micrographs of the PP before and after plasma treatment are observed by scanning electron microscopy (SEM) and the chemical composition of the PP surface before and after plasma treatment is also analyzed by Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). The results show that the surface hydrophilic property of the PP samples is greatly improved with plasma treatment for a few seconds, as evidenced by the fact that the contact angle of the treated PP samples significantly decreases after plasma treatment. The analysis of SEM shows that the surface roughness of the treated PP samples increases due to bonding and etching in plasma processing. The analyses of FTIR and the C1s peak in the high-resolution XPS indicate that oxygen-containing and nitrogen-containing polar functional groups are introduced into PP surface in plasma processing. It can be concluded that the surface hydrophilic property of the modified PP samples has been obviously improved due to the introduction of oxygen-containing and nitrogen-containing polar groups and the increase of the surface roughness on the PP surface.     

交流和纳秒脉冲Ar/H2O介质阻挡放电聚丙烯材料表面亲水改性对比研究

为了提高等离子体对聚合物材料表面处理的应用效果,优化亲水处理的条件,研究了交流和纳秒脉冲氩气介质阻挡放电（DBD）中添加适量H₂O,对聚丙烯（PP）亲水改性的处理效果。利用电学和光学诊断方法,系统地对比了交流DBD和纳秒脉冲DBD的放电特性,结果表明,纳秒电源驱动DBD具有更高的放电瞬时功率,更好的放电均匀性和更高的能量效率。通过测量不同水蒸气含量下DBD的OH发射光谱强度,确定了PP材料亲水性处理中H₂O添加的最优含量。利用交流和纳秒脉冲电源驱动DBD分别对PP材料进行亲水改性的处理,测量了不同条件下改性处理后的表面水接触角,并利用原子力显微镜（AFM）和傅里叶红外光谱（FTIR）分别对处理前后PP材料的表面物理形貌和表面化学成分进行分析。结果发现,经DBD处理后PP材料的水接触角明显降低,表面粗糙度明显增大,表面的亲水性含氧基团,羟基（?OH）和羰基（C=O）的数量大幅增加。相比交流电源,纳秒脉冲DBD处理的改性效果更好,其处理后的材料表面水接触角,比交流DBD处理的低5°左右,表面粗糙度也有所提升。而水蒸气的加入可使PP材料的表面水接触角进一步减小4°左右,表面粗糙度明显提升。研究结果为优化DBD聚合物材料表面改性实验条件及处理的效果提供了重要的参考依据。     

Polypropylene modified with 2-hydroxyethyl acrylate-g-2-methacryloyloxyethyl phosphorycholine and its hemocompatibility

Polypropylene (PP) was modified with 2-hydroxyethyl acrylate (HEA) by solution radical grafting to introduce active hydroxyl groups on polypropylene backbone (PP-g-HEA). Then the biomimic monomer, 2-methacryloyloxyethyl phosphorycholine (MPC), was grafted onto the surface of PP-g-HEA film (PP-g-HEA-g-MPC) by redox graft polymerizations with ceric(IV) ammonium nitrate as an initiator. Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) showed that the HEA and MPC were introduced onto PP molecular chains and the copolymer, PP-g-HEA-g-MPC were formed. The water contact angle measurements demonstrated that the final modified PP film exhibited a better hydrophilic surface compared to the neat PP film. The platelets adhesion on the neat PP, PP-g-HEA and PP-g-HEA-g-MPC film was examined by scanning electron microscopy (SEM). It was found that a large number of platelets were adhered and activated on the surface of neat PP and PP-g-HEA films, while the number of platelets on PP-g-HEA-g-MPC surface was decreased remarkably. The result revealed that the introduction of poly(MPC) onto the PP surface improved the hemocompatibility of PP substantially.     

Enrichment of poly(methyl methacrylate) and its graft copolymer of polybutadiene on the surface of polypropylene blends

Poly(methyl methacrylate) (PMMA) and its graft copolymer of polybutadiene were used as the macromolecular surface modifiers of polypropylene. The enrichment and diffusion of the modifiers onto the surface of polypropylene blends were investigated using FTIR-ATR, CDA and SEM. It has been found that the selective aggregation of the modifier component on the surface of polypropylene was mainly affected by the content, molecular weight and size of the segregated domains. Lower content and higher surface energy die were in favor of the enrichment of the additive. PMMA with higher molecular weight showed larger domain phase and lower diffusion velocity which resulted in less enrichment on the surface of PP blends.     

Modification of surface properties of polypropylene (PP) film using DC glow discharge air plasma

The industrial use of polypropylene (PP) films is limited because of undesirable properties such as poor adhesion and printability. In the present study, a DC glow discharge plasma has been used to improve the surface properties of PP films and make it useful for technical applications. The change in hydrophilicity of modified PP film surface was investigated by contact angle (CA) and surface energy measurements as a function of exposure time. In addition, plasma-treated PP films have been subjected to an ageing process to determine the durability of the plasma treatment. Changes in morphological and chemical composition of PP films were analyzed by atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The improvement in adhesion was studied by measuring T-peel and lap shear strength. The results show that the surface hydrophilicity has been improved due to the increase in the roughness and the introduction of oxygen-containing polar groups. The AFM observation on PP film shows that the roughness of the surface increased due to plasma treatment. Analysis of chemical binding states and surface chemical composition by XPS showed an increase in the formation of polar functional groups and the concentration of oxygen content on the plasma-processed PP film surfaces. T-peel and lap shear test for adhesion strength measurement showed that the adhesion strength of the plasma-modified PP films increased compared with untreated films surface.     

衰减全反射傅里叶红外光谱在聚丙烯的表面改性的应用

应用衰减全反射傅里叶变换红外光谱法(ATR-FTIR)对聚丙烯共混薄膜的表面组成进行了测试.通过比尔定律的验证,确认1 103和1 733 cm-1可以分别用于含聚乙二醇和含羰基结构单元的改性剂共混体系的定量计算.利用ATR校正程序,以相应的特征峰峰面积比作为定量测定的基准,可以减少测试误差.通过工作曲线法,定量地分析了聚丙烯共混物薄膜表层中改性剂的含量.此外,利用变角全反射,通过改变入射光线的角度,可以测定不同深度的改性剂含量,剖析改性剂在PP共混薄膜的表层分布.     

Fabrication of superhydrophobic silica-based surfaces with high transmittance by using tetraethoxysilane precursor and different polymeric species

The preparation of superhydrophobic silica-based surfaces via the sol-gel process through the addition of different polymeric species into the precursor solution was done in this study. The surface roughness of the films was obtained by removing the organic polymer at a high temperature, and then the hydrophobic groups were bonded onto the films with a monolayer by chemical reaction with hexamethyldisilazane (HMDS). The characteristic properties of the as-prepared films were analyzed by contact angle measurements, scanning electron microscopy (SEM), atomic force microscopy (AFM), nitrogen adsorption/desorption, and UV-vis scanning spectrophotometer. The experimental results revealed that the superhydrophobic thin films with high transmittance could easily be prepared using polypropylene (PPG), polyethylene (PEG), and poly(vinylpyrrolidone) (PVP). Surface roughness and pore size were enhanced using PPG polymeric species. The distribution of pore size was from the microporous to the mesoporous and marcoporous regions. In addition, the contact angles of the rough surfaces prepared at 500 °C without modification of HMDS were smaller than 5° but larger than 156° after modified by HMDS.     

Biocompatibility of polypropylene non-woven fabric membrane via UV-induced graft polymerization of 2-acrylamido-2-methylpropane sulfonic acid

This work described the graft polymerization of a sulfonic acid terminated monomer, 2-acrylamido-2-methylpropane sulfonic acid (AMPS), onto the surface of polypropylene non-woven (NWF PP) membrane by O₂ plasma pretreatment and UV-induced photografting method. The chemical structure and composition of the modified surfaces were analyzed by FTIR-ATR and XPS, respectively. The wettability was investigated by water contact angle and equilibrium water adsorption. And the biocompatibility of the modified NWF PP membranes was evaluated by protein adsorption and platelet adhesion. It was found that the graft density increased with prolonging UV irradiation time and increasing AMPS concentration; the water contact angles of the membranes decreased from 124° to 26° with the increasing grafting density of poly(AMPS) from 0 to 884.2 μg cm⁻², while the equilibrium water adsorption raised from 5 wt% to 75 wt%; the protein absorption was effectively suppressed with the introduction of poly(AMPS) even at the low grafting density (132.4 μg cm⁻²); the number of platelets adhering to the modified membrane was dramatically reduced when compared with that on its virgin surface. These results indicated that surface modification of NWF PP membrane with AMPS was a facile approach to construct biocompatible surface.     

Crystallization Kinetics of Linear and Long‐Chain Branched Polypropylene

Isothermal crystallization kinetics of linear polypropylene (PP) and long‐chain branched (LCB) PPs were investigated on the basis of the Avrami theory. The Avrami exponents of LCB PPs are smaller than that of linear PP; moreover, they decrease with an increasing LCB level. The crystallization half‐time of LCB PP depends more strongly on the crystallization temperature than does that of linear PP. The Lauritzen‐Hoffman theory was used to study the effect of LCB on the crystal growth rate of PP. The fold surface free energy of LCB PP is lower than that of linear PP; moreover, it decreases with an increasing LCB level. However, when the LCB level is over a certain value, the fold surface free energy increases again. Furthermore, the crystal structures of linear PP and LCB PPs were studied by wide‐angle X‐ray diffraction (WAXD); it was observed that linear PP can crystallize in the α and β forms, while LCB PPs have only the α crystalline form. Moreover, the relative intensities of different α peaks were also influenced by the LCB level.     

Nanosurface Mechanical Properties of Polymers Based on Continuous Stiffness Indentation

A systematic experimental study of the large strain surface mechanical properties of a number of polymers {polymethylmethacrylate (PMMA), polyetheretherketone (PEEK), polystyrene (PS), polycarbonate (PC), polypropylene (PP), and ultra-high molecular weight polyethylene (UHMWPE)} at the nanometer scale is described. The polymeric surfaces were indented and the data were analyzed using a contact compliance method in conjunction with a nano-indenter system. The indentation experiments were performed using a Berkovich Tip indenter with a continuous contact compliance indentation mode. The indentations were performed using a constant loading rate (300 μN/sec) to a maximum penetration depth of 5 μm. The experimental results showed a considerable strain-rate hardening effect for the polymers and a peculiarly harder response of these surfaces at the near-to-surface (submicron) layers. PMMA was the hardest polymer of the selection, whereas UHMWPE and PP were observed to be the softest polymers. The paper includes practical consideration of a creeping effect and appropriateness of tip calibration using harder surfaces for nanoindentation experimentation of polymers.     

Different configurations of transferred atmospheric pressure plasma jet and their application to polymer treatment

The employment of atmospheric pressure plasma jets (APPJs) in a large sort of applications is limited by the adversities related to the size of the treated area and the difficulty to reach the target. The use of devices that employ long tubes in their structure has contributed significantly to overcome these challenges. In this work, two different plasma systems employing the jet transfer technique are compared. The main difference between the two devices is how the long plastic tube was assembled. The first one uses a copper wire placed inside a long plastic tube. The other device has a metallic mesh installed in a concentric arrangement between two coaxial plastic tubes. As a result, the two APPJ systems exhibit different properties, with the wire assembly being more powerful, also presenting higher values for the electrical current and rotational temperature when compared to the mesh mounting. X-ray photoelectron spectroscopy (XPS) demonstrates that both configurations were capable of inserting O-containing functional groups on the polypropylene (PP) surface. However, the transferred plasma jet with wire assembly was able to add more functional groups on the PP surface. The results from XPS analysis were corroborated with water contact angle measurements (WCA), being that lower WCA values were obtained when the PP surface presented higher amounts of O-containing groups. Furthermore, the results suggest that the APPJ with wire configuration is more appropriate for material treatments, while the transferred jet with mesh arrangement tends to present lower electrical current values, being more suitable for biological applications.     

极化电压对聚丙烯压电驻极体膜压电性能的影响

压电驻极体是具有压电效应的微孔结构空间电荷驻极体材料,其压电性能与材料的微结构和空间电荷密切相关.本文首先利用压缩气体膨化工艺对聚丙烯(PP)的微结构进行改性,然后利用接触极化方法,研究了极化电压与PP膜空间电荷密度之间的关系,及其对压电性能的影响.结果表明对于极化前厚度为100μm的PP膜,其内部建立有序空间电荷分布的阈值极化电压为2 kV;一旦有序空间电荷建立起来,PP膜即具有压电效应.随着极化电压的提高,PP膜的空间电荷密度逐步增大,压电效应显著增强.当峰值电压为8 kV时,PP膜电极上的电荷密度、准静态压电系数和品质因数FOMv(d33·g33)分别为0.56 mC/m2,379 pC/N和8.6(GPa)-1.PP压电驻极体膜的FOMv比聚偏氟乙烯(PVDF)铁电聚合物膜高2个量级以上,且声阻抗非常低(～0.025 MRayl),因此该压电膜在超声波发射-接收系统或脉冲-回波系统中具有明显的优势.     

Plasma-induced graft-polymerization of polyethylene glycol acrylate on polypropylene substrates

A detailed study of argon plasma-induced graft-polymerization of polyethylene glycol acrylate (PEGA) on polypropylene (PP) substrates (membranes and films) is presented. The process consists of four steps: (a) plasma pre-activation of the PP substrates; (b) immersion in a PEGA solution; (c) argon plasma-induced graft-polymerization; (d) washing and drying of the samples. Influence of the solution and plasma parameters on the process efficiency evaluated in terms of amount of grafted polymer, coverage uniformity and substrates wettability, are investigated. The plasma-induced graft-polymerization of PEGA is then followed by sample weighting, water droplet adsorption time and contact angle measurements, attenuated total reflection infrared spectroscopy (ATR-IR), X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) analyses. The stability of the obtained thin films was evaluated in water and in phosphate buffer saline (PBS) at 37 °C. Results clearly indicates that plasma-induced graft-polymerization of PEGA is a practical methodology for anti-fouling surface modification of materials.     

Mechanical,Thermal, and Surface Properties of Ultrahigh Molecular Weight Polyethylene/Polypropylene Blends

Various compositions of ultrahigh molecular weight polyethylene/polypropylene (UHMWPE/PP) blends were prepared in decalin, with the rheological, mechanical, thermal, and surface properties of the blends being determined using the solution cast film. Viscosity and mechanical properties of the blends decreased below the additivity value with increasing PP content implying that PP molecules disturb the entanglement of UHMWPE. Contact angle of the blend films with a water drop increased with increasing content of PP. The atomic force microscope (AFM) images showed that the surface of cast UHMWPE was very smooth whereas that of cast PP was very uneven. For blends, the surface became rough and uneven with increasing content of PP. The melting temperature of PP (T _mP) decreased in the blends with increasing UHMWPE content while that of UHMWPE (T _mU) remained almost constant in blends.     

3′-Hydroxy-4-methoxychalcone as a potential antibacterial coating on polymeric biomaterials

Antimicrobial property of chalcone coated high density polyethylene (HDPE), low density polyethylene (LDPE), polypropylene (PP) and polyurethane (PU) against Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa is reported here. The presence of chalcone on the surface was confirmed from fourier transform infrared spectroscopy (FT-IR) and scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). Bacterial adhesion decreased considerably on all the coated surfaces. Bacterial adhesion was highest on PU surface (most hydrophobic) and lowest on HDPE (most hydrophilic) surface. Chalcone seems to damage the membrane of the bacteria as well as exhibit slimicidal activity. Reasonably good correlation was observed between the CFU (Colony Forming Units) ratio (it is defined as the ratio of CFU on coated surface to the chalcone uncoated surface) at the 24th hour against both hydrophobicity of the microorganism and roughness of the coated polymeric surfaces. Increasing roughness of the polymer and hydrophobicity of the microorganisms were positively and negatively correlated respectively with CFU ratio. Hence, the chalcone coated polymers can be used in the development of newer biomaterials.     

Morphology and mechanical properties of PP/HMWPE blends

Mechanical properties and morphology of blends of polypropylene (PP) with high molecular weight polyethylene (HMWPE) prepared by coprecipitation from xylene solution are investigated. Compared to blends of PP with commercial high-density polyethylene (HDPE), the mechanical properties of the blends of PP/HMWPE are much superior to those of PP/HDPE blends. Not only is the tensile strength stronger, but also the elongation at break is much higher than that of the PP/HDPE blends of the same composition. These differences increase with increasing HMWPE and HDPE content. Scanning electron microscopy of the fracture surface resulting from the tensile tests shows that the compatibility in PP/ HMWPE blends is much better than that in PP/HDPE blends. This is most likely attributable to the enhanced chain entanglement of HMWPE with the PP in the amorphous phase due to the lower crystallinity, owing to the high molecular weight of the HMWPE, and a much more flexible chain. The thermal behavior and spherulite morphology of both blends are also investigated.     

Static secondary ion mass spectrometry (S-SIMS) analysis of atmospheric plasma treated polypropylene films

Time-of-Flight (TOF) static secondary ion mass spectrometry (S-SIMS) was used to gain molecular information on the surface modifications introduced by plasma treatment of polypropylene (PP) films. A procedure using slotted electron microscopy grids was developed to deal with the charge build-up of samples with a thickness of about 30 μm. The surface composition was studied as a function of the plasma treatment time. A comparison of the mass spectra from untreated and treated PP showed significant differences of signal intensities of ions that could be specifically related to the presence of oxygen-containing species.     

Relationship Between Interfacial Adhesion and Viscosity of Cellulose Fiber Filled Polypropylene and Poly(ε-caprolactone): A Review

The relationship between interfacial adhesion and dynamic viscosity of regenerated cellulose fiber (CF) filled in poly(ε-caprolactone) (PCL) and polypropylene (PP) matrix is compared. The rate of viscosity rise from its virgin polymer of the PCL/CF compounds shows higher than that of the PP/CF ones at the same CF loadings. The interfacial adhesion of the CF surface with the PCL matrix is better than with the PP due to polar characteristic of the PCL. Striking differences are observed in the PCL compounds. As the concentration of the particles increases, the crystalline temperature, the spherulite formation, the elongation modulus and the yield stress of the PCL/CF compounds are significantly higher than those of the PP/CF compounds. More spherulites are locally developed on the CF surface in the PCL/CF compounds than in the PP/CF ones. The higher rate of viscosity rise of the PCL/CF compounds than the PP/CF compounds is due to higher interfacial adhesion of the CF surface with the PCL than with the PP.