Combined X-ray-electron imaging techniques: Limitations on lateral resolution

Capabilities of the imaging techniques, in which X-rays are converted to electrons and then the emitted electrons are registered by means of an electron microscope, are analyzed, the focus being on the factors limiting lateral resolution at the stage of electron emission. Bearing in mind the tendency to use harder synchrotron X-rays for some combined X-ray-electron microscopy methods, calculations were made for two significantly different X-ray energies: E = 1.828 keV (K-edge of Si) and E = 11.923 keV (L₃-edge of Au). By using Monte Carlo simulations of the electron trajectories beneath the surface of the sample we show that the radius of the spot from which photoelectrons are emitted could be as small as 1 nm. However, when proper account is taken of an entire electron cascade associated with the re-building of electron shells after photoelectron emission, spots more than one order of magnitude larger result, limiting the best lateral resolution to 20–30 nm.     

Structural and morphological characterisation of hybrid Cu/Si(0 0 1) structures

The structural and morphological properties of epitaxial Cu/Si(0 0 1) type of structures have been investigated by a combination of electron, X-ray and scanning probe imaging techniques. Auger electron spectroscopy measurements indicate the presence of Si in the Cu layer for Cu thicknesses up to 10 nm. In addition, X-ray scattering results show that there is a mosaic spread in the Cu(0 0 1) crystal which decreases as the Cu thickness increases, from 8° at 15 nm to 4.5° at 100 nm. This behaviour is corroborated by reflection high energy electron diffraction patterns of the Cu surface measured during growth, which exhibit a twinning in the diffraction spots for the 15 and 30 nm Cu films. Atomic force and scanning electron microscopy imaging of Cu(4 nm)/Co(7,17 nm)/Cu(100 nm)/Si(0 0 1) structures allow one to visualise and characterise the sample surface in real space; from these measurements, an average roughness amplitude of ∼0.5 nm and a correlation length of ∼50 nm are obtained. Our results provide a better understanding of an important system which has been widely used as a template for the growth of epitaxial ultrathin magnetic films.     

Effects of annealing temperature on structure and magnetic properties of CoAl0.2Fe1.8O4/SiO2 nanocomposites

CoAl_0.2Fe_1.8O₄/SiO₂ nanocomposites were prepared by sol–gel method. The effects of annealing temperature on the structure and magnetic properties of the samples were studied by X-ray diffraction, transmission electron microscopy, vibrating sample magnetometer and Mössbauer spectroscopy. The results show that the CoAl_0.2Fe_1.8O₄ in the samples exhibits a spinel structure after being annealed. As annealing temperature increases from 800 to 1200 °C, the average grain size of CoAl_0.2Fe_1.8O₄ in the nanocomposites increases from 5 to 41 nm while the lattice constant decreases from 0.8397 to 0.8391 nm, the saturation magnetization increases from 21.96 to 41.53 emu/g. Coercivity reaches a maximum of 1082 Oe for the sample annealed at 1100 °C, and thereafter decreases with further increasing annealing temperature. Mössbauer spectra show that the isomer shift decreases, hyperfine field increases and the samples transfer from mixed state of superparamagnetic and magnetic order to the completely magnetic order with annealing temperature increasing from 800 to 1200 °C.     

Optical properties of cadmium sulfide nanocrystal film prepared by electrochemical synthesis at liquid-liquid interface

Dendritic nanocrystalline CdS film was deposited at liquid-liquid interface of surfactants and an electrolyte containing 4 mmol L⁻¹ cadmium chloride (CdCl₂) and 16 mmol L⁻¹ thioacetamide (CH₃CSNH₂) with an initial pH value of 5 at 15 °C by electrochemical synthesis. The nanofilm was characterized by transmission electron microscopy (TEM), field emission scanning electron microscope (FE-SEM), atomic force microscopy (AFM), ultraviolet visible (UV-vis) absorption spectroscopy and fluorescence spectroscopy. The surface morphology and particle size of the nanofilm were investigated by AFM, SEM and TEM, and the crystalline size was 30-50 nm. The thickness of the nanofilm calculated by optical absorption spectrum was 80 nm. The microstructure and composition of the nanofilm was investigated by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), showing its polycrystalline structure consisting of CdS and Cd. Optical properties of the nanofilm were investigated systematically by UV-vis absorption and fluorescence spectroscopy. A λ_onset blue shift compared with bulk CdS was observed in the absorption spectra. Fluorescence spectra of the nanofilm indicated that the CdS nanofilm emitted blue and green light. The nanocomposites film electrode will bring about anodic photocurrent during illumination, showing that the transfer of cavities produces photocurrent.     

Solid phase epitaxy of Ge films on CaF2/Si(1 1 1)

At room temperature deposited Ge films (thickness < 3 nm) homogeneously wet CaF₂/Si(1 1 1). The films are crystalline but exhibit granular structure. The grain size decreases with increasing film thickness. The quality of the homogeneous films is improved by annealing up to 200 °C. Ge films break up into islands if higher annealing temperatures are used as demonstrated combining spot profile analysis low energy electron diffraction (SPA-LEED) with auger electron spectroscopy (AES). Annealing up to 600 °C reduces the lateral size of the Ge islands while the surface fraction covered by Ge islands is constant. The CaF₂ film is decomposed if higher annealing temperatures are used. This effect is probably due to the formation of GeF_x complexes which desorb at these temperatures.     

Laser-induced forward transfer technique for maskless patterning of amorphous V2O5 thin film

A laser-induced forward transfer technique has been applied for the maskless patterning of amorphous V₂O₅ thin films. A sheet beam of a frequency doubled (SHG) Q-switched Nd:YAG laser was irradiated on a transparent glass substrate (donor), the rear surface of which was pre-coated with a vacuum-deposited V₂O₅ 180 nm thick film was either in direct contact with a second glass substrate (receiver) or a 0.14 mm air-gap was maintained between the donor film and the receiving substrate. Clear, regular stripe pattern of the laser-induced transferred film was obtained on the receiver. The pattern was characterized using X-ray diffraction (XRD), optical absorption spectroscopy, scanning electron microscopy (SEM), energy dispersive analysis of X-ray (EDAX), atomic force microscopy (AFM), etc.     

Growth of Co nanoparticles on a nanostructured θ-Al2O3 film on CoAl(1 0 0)

We have investigated the growth of Co nanoparticles on θ-Al₂O₃/CoAl(1 0 0) by means of Auger electron spectroscopy (AES), high-resolution electron energy loss spectroscopy (EELS), low energy electron diffraction (LEED) and scanning tunneling microscopy (STM). Due to Volmer-Weber growth, Co forms particles with a mean diameter of approximately 2.5 nm and height of 0.8 nm. Even on the entirely covered oxide, there is no Ostwald ripening and Co particles stay structurally isolated. The nanoparticles exhibit a small size distribution and tend to form chains, as predetermined by the streak structure of the oxide template. For sufficient high coverages Co-core-CoO-shell nanoparticles may be evidenced, which is explained as a result of surfactant oxygen. The nanostructured particles may open the door to numerous applications, such as in catalysis and magnetoelectronic applications, where large areas of ordered nanodots are desired.     

Analysis of materials modifications caused by UV laser micro drilling of via holes in AlGaN/GaN transistors on SiC

Pulsed UV laser drilling can be applied to fabricate vertical electrical interconnects (vias) for AlGaN/GaN high electron mobility transistor devices on single-crystalline silicon carbide (SiC) substrate. Through-wafer micro holes with a diameter of 50-100 μm were formed in 400 μm thick bulk 4H-SiC by a frequency-tripled solid-state laser (355 nm) with a pulse width of ≤30 ns and a focal spot size of ∼15 μm. The impact of laser machining on the material system in the vicinity of micro holes was investigated by means of micro-Raman spectroscopy and transmission electron microscopy. After removing the loosely deposited debris by etching in buffered hydrofluoric acid, a layer of <4 μm resolidified material remains at the side walls of the holes. The thickness of the resolidified layer depends on the vertical distance to the hole entry as observed by scanning electron microscopy. Micro-Raman spectra indicate a change of internal strain due to laser drilling and evidence the formation of nanocrystalline silicon (Si). Microstructure analysis of the vias’ side walls using cross sectional TEM reveals altered degree of crystallinity in SiC. Layers of heavily disturbed SiC, and nanocrystalline Si are formed by laser irradiation. The layers are separated by 50-100 nm thick interface regions. No evidence of extended defects, micro cracking or crystal damage was found beneath the resolidified layer. The precision of UV laser micro ablation of SiC using nanosecond pulses is not limited by laser-induced extended crystal defects.     

Magnetic and structural studies of the Mn-doped Mg–Zn ferrite nanoparticles synthesized by the glycine nitrate process

In this study, Nanocrystalline Mn–Mg–Zn ferrite with the chemical formula Mn_xMg_0.5−xZn_0.5Fe₂O₄ (x=0, 0.1, 0.2, 0.3, 0.4, 0.5) was successfully synthesized by the glycine-nitrate autocombustion process using glycine as a fuel and nitrates as oxidants. The as-synthesized powders were characterized by the X-ray diffraction analysis, field emission scanning electron microscopy, Fourier transform infrared spectroscopy (FTIR) and vibrating sample magnetometer. The X-ray diffraction data was used to determine the lattice constant, cation distribution and the oxygen position parameter. The results reveal that the nanocrystalline Mn–Mg–Zn ferrite has an average crystallite size of 35–67 nm and particle size of 40 nm. The lattice parameter increases linearly with an increase in the Mn content. The FTIR analysis confirms the intrinsic vibrational frequencies of the tetrahedral and octahedral of the spinel structure. The magnetic measurements indicate that the coercivity decreases, and the magnetization increases by increasing the Mn content.     

Ni80Fe20 permalloy nanoparticles: Wet chemical preparation, size control and their dynamic permeability characteristics when composited with Fe micron particles

Ni₈₀Fe₂₀ permalloy nanoparticles (NPs) have been prepared by the polyol processing at 180 °C for 2 h and their particle sizes can be precisely controlled in the size range of 20-440 nm by proper addition of K₂PtCl₄ agent. X-ray diffraction results show that the Ni-Fe NPs are of FCC structure, and a homogeneous composition and a narrow size distribution of these NPs have been confirmed by scanning electron microscopy assisted with energy dispersion spectroscopy of X-ray (SEM-EDX). The saturation magnetization of ~440nm NPs is 80.8 emu/g that is comparable to that of bulk Ni₈₀Fe₂₀ alloys, but it decreases to 28.7 emu/g for ~20 nm NPs. The coercive force decreases from 90 to 3 Oe with decreasing NP size. The wide range of particle size is exploited to seek for high permeability composite particles. The planar type samples composed of the NiFe NPs exhibit low initial permeability due to the deteriorated magnetic softness and low packing density. However, when they are mixed with Fe micron particles, the initial permeability significantly increases depending on the mixing ratio and the NiFe NP size. A maximum initial permeability is achieved to be ~9.1 at 1 GHz for the Fe-10 vol%NiFe (~20 nmΦ), which is about three times that of pure Fe micron particles. The effects of Ni-Fe particle size, volume percentage and solvent on the static and dynamic permeability are discussed.     

Structural and spectroscopic studies of thin film of silver nanoparticles

We report the deposition of thin film of silver (Ag) nanoparticles by wet chemical method. The as-synthesized Ag nanoparticles have been characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), X-ray energy dispersive spectroscopy (EDS), field emission transmission electron microscopy (FETEM) and high-resolution TEM (HRTEM), UV-vis spectroscopy and thermogravimetric-differential thermal analysis (TG-DTA) respectively. FESEM image indicates that the silver film prepared on the quartz substrate is smooth and dense. XRD pattern reveals the face-centered cubic (fcc) structure of silver nanoparticles. EDS spectrum indicates that samples are nearly stoichiometric. From TEM analysis, it is found that the size of high purity Ag nanoparticles is ranging from 10 to 20 nm with slight agglomeration. Absorption in UV-vis region by these nanoparticles is characterized by the features reported in the literature, namely, a possible Plasmon peak at ∼403 nm. Optical absorbance spectra analysis reveals that the Ag film has an indirect band structure with bandgap energy 3.88 eV. TGA/DTA studies revealed that a considerable weight loss occurs between 175 and 275 °C; and the reaction is exothermic.     

Evolution of structure, microstructure and hyperfine properties of nanocrystalline Fe50Co50 powders prepared by mechanical alloying

Nanostructured Fe₅₀Co₅₀ powders were prepared by mechanical alloying of Fe and Co elements in a vario-planetary high-energy ball mill. The structural properties, morphology changes and local iron environment variations were investigated as a function of milling time (in the 0-200 h range) by means of X-ray diffraction, scanning electron microscopy (SEM), energy dispersive X-ray analysis and ⁵⁷Fe Mössbauer spectroscopy. The complete formation of bcc Fe₅₀Co₅₀ solid solution is observed after 100 h milling. As the milling time increases from 0 to 200 h, the lattice parameter decreases from 0.28655 nm for pure Fe to 0.28523 nm, the grain size decreases from 150 to 14 nm, while the meal level of strain increases from 0.0069% to 1.36%. The powder particle morphology at different stages of formation was observed by SEM. The parameters derived from the Mössbauer spectra confirm the beginning of the formation of Fe₅₀Co₅₀ phase at 43 h of milling. After 200 h of milling the average hyperfine magnetic field of 35 T suggests that a disordered bcc Fe-Co solid solution is formed.     

Structural characterization and optical properties of UO2 thin films by magnetron sputtering

Uranium dioxide films were deposited on Si (1 1 1) substrates by dc magnetron sputtering method at different sputtering parameters. The structure, morphology and chemical state of the films were studied by field emission scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and atomic force microscopy. Influences of film thickness on the microstructure and optical properties were investigated. Experimental results show that the film crystallites are preferentially oriented with the (1 1 1) planes. The average grain size increases with increasing film thickness. AFM images show that the root mean square roughness of the films is between 1.2 nm and 2.1 nm. Optical constants (refractive index, extinction coefficient) of the films in the wavelength range of 350-1000 nm are obtained by ellipsometric spectroscopy. The result shows that the refractive index decreases with the increasing film thickness, while extinction coefficient increases with the film thickness.     

Efficient field emission from coiled carbon nano/microfiber on copper substrate by dc-PECVD

Crystalline coiled carbon nano/micro fibers in thin film form have been synthesized via direct current plasma enhanced chemical vapor deposition (PECVD) on copper substrates with acetylene as a carbon precursor at 10 mbar pressure and 750 °C substrate temperature. The as-prepared samples were characterized by X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM) and high resolution transmission electron microscopy (HRTEM). XRD pattern as well as selected area electron diffraction (SAED) pattern showed that the samples were crystalline in nature. SEM and HRTEM studies showed that as synthesized coiled carbon fibers are having average diameter ∼100 nm and are several micrometers in length. The as-prepared samples showed moderately good electron field emission properties with a turn-on field as low as 1.96 V/μm for an inter-electrode distance 220 μm. The variation of field emission properties with inter-electrode distance has been studied in detail. The field emission properties of the coiled carbon fibrous thin films are compared with that of crystalline multiwalled carbon nanotubes and other carbon nanostructures.     

Effect of sol concentration on the properties of ZnO thin films prepared by sol-gel technique

ZnO thin films are deposited on the glass substrates by sol-gel drain coating technique by varying the concentration of the sol. X-ray diffraction (XRD) and scanning electron microscopy (SEM) analysis were used to investigate the effect of sol concentration on the crystallinity and surface morphology of the films. The results show that with increase in sol concentration, the value of full width at half maximum (FWHM) of (0 0 2) peak decreases while the strain first increases and then decreases. The sol with higher concentration results in the increase in the grain size. The studies on the optical properties show that the band gap value increases from 3.27 to 3.3 eV when the sol concentration changes from 0.03 to 0.1 M. The photoconductivity studies reveal that the film for 0.05 M sol shows the maximum photoresponse for ultraviolet (UV) wavelength (<400 nm) which is co-related with the deep-level defects. The growth and decay of the photocurrent is found to be slowest for the same film.     

Synthesis and optical characterization of PVP and SHMP-encapsulated Mn-doped ZnS nanocrystals

Zinc sulfide semiconductor nanocrystals doped Mn²⁺ have been synthesized via a solution-based method utilizing optimum dopant concentration (4%) and employing polyvinyl pyrrolidone (PVP) and sodium hexametapolyphosphate (SHMP) as capping agents. UV-vis absorbance spectra for all of the synthesized nanocrystals show an exitonic peak at around 310 nm. The particle size and morphology were characterized by scanning electron microscopy (SEM), FT-IR, X-ray diffraction (XRD), transmission electron microscopy (TEM) and photoluminescence spectrum (PL). Diffraction data confirmed that the crystallite size is around 3-5 nm. Room temperature photoluminescence (PL) spectrum for the bare ZnS sample shows a strong band at ∼445 nm. The uncapped and capped(SHMP, PVP) ZnS:Mn²⁺ samples show a strong and broad band in the ∼580-585 nm range.     

Size dependent electron momentum density distribution in ZnS

In this paper, we present size dependent electron momentum density distribution in ZnS. ZnS nanoparticles of size 3.8 nm and 2.4 nm are synthesized using the chemical route and characterized by X-ray diffraction (XRD). The Compton profile measurements are performed on both the nano-sized as well as bulk ZnS samples employing 59.54 keV gamma-rays from ²⁴¹Am source. The results reveal that the valence electron density in momentum space becomes narrower with reduction of particle size. To evaluate the charge transfer on compound formation, the ionic model based calculations for a number of configurations of Zn^+xS^−x (0.0≤x≤2) are also performed utilizing free atom Compton profiles. These results suggest different amounts of charge transfer in these materials varying from 1.2 to 2.0 electron from Zn to S atom.     

Atomic structure of a regular Si(2 2 3) triple step staircase

An atomically accurate regular triple step array with a period of 4.8 nm has been fabricated on the vicinal Si(5 5 7) surface. Its atomic structure was studied on different length scales by scanning tunneling microscopy, low energy electron diffraction and photoelectron spectroscopy. These complementary methods allowed to identify the average orientation of the regular triple step staircase as Si(2 2 3) and to give a deeper insight into the atomic arrangement of this structure.     

Nanoscale dislocation patterning in Bi(1 1 1)/Si(0 0 1) heteroepitaxy

Continuous, atomically flat, and epitaxial Bi(1 1 1) films could be grown on Si(0 0 1). The inherent strain of 2.3% between the Bi(1 1 1) and Si(0 0 1) lattices is relieved by the formation of a grating like one-dimensional misfit dislocation array at the heterointerface. The lattice distortions around each dislocation give rise to a pronounced height depression Δh = 0.12 nm of the surface, which results in a spot splitting in low-energy electron diffraction and a height contrast in scanning tunneling microscopy (STM). Using STM surface profiles across these depressions, the Burgers vector of the underlying isolated non-interacting dislocations is estimated to be 0.377 nm. For thicker Bi films the ordering of the dislocation network is increased. This reflects an increase of repulsive interaction between neighboring dislocations.     

Effect of spot size on cone formation in a XeCl laser ablation of polyethersulfone films

Radiation from the UV excimer lasers, with the fluence above the ablation threshold, can etch the polymer surfaces by photoablation. In some cases different microstructures may appear on the surface during the laser ablation. In this paper the effect of the laser spot size on the cone formation on polyethersulfone films has been investigated. The experiments have been performed with a XeCl laser at the wavelength of 308 nm and at the fluences of 70 and 100 mJ/cm² at air. For the investigation of the effect of the laser spot size on cone formation, the samples were irradiated at two different laser spot sizes of w₁ and w₂ = 0.1 w₁. The morphology of the processed surface was studied by scanning electron microscopy (SEM). It has shown that the shape, size and density of cones change with the change of the laser spot size. Also, the number of pulses and the pulse repetition rate which are needed for threshold of cone formation are affected by the laser beam spot size on the surface.