光子带隙光纤的可调谐泄漏损耗特性的研究

通过向折射率引导型光子晶体光纤的空气孔中填充可调的高折射率的材料可以获得带隙可调的光子带隙光纤.本文采用矢量平面波展开法与矢量有限元法对可调光子带隙光纤的泄漏损耗特性进行了理论研究.研究表明，这种可调光子带隙光纤的光子带隙效应使其泄漏损耗与填充材料的折射率有很强的依赖关系，同时给出了光子带隙光纤的泄漏损耗和群速度色散与归一化波长的关系.     

4.3μm低损耗硫系空芯光子带隙光纤结构设计及性能研究

运用平面波展开法分析As2S3、Ge20Se65Sb15和As2Se3硫系玻璃光纤在不同空气填充率下的带隙分布图,分析结果表明三种材料在空气填充率提高到0.75时,光子带隙与空气线均出现交汇模式,且带隙宽度大,纤芯空气孔中适宜进行激光传输.运用有限元法分析不同纤芯孔直径的Ge20Se65Sb15硫系玻璃空芯光子带隙光纤的基模限制损耗和有效模场面积,结果表明纤芯直径9.2μm时限制损耗最低,模场面积较小.通过优化光纤的结构参量,适合于4.3μm波长处高功率中红外激光传输的空芯光子带隙光纤,其限制损耗为0.00472dB/m,有效模场面积为58.046μm2.     

全固态光子带隙光纤第1带隙内模场分布特性

利用多极法计算了全固态光子带隙光纤第1带隙内不同波长处的基模模场分布,得到2维归一化光强分布特性.由于该光纤具有三角形(C<,6v>)的对称结构,影响了光纤内的模场分布,为此计算了该结构两个具有代表性的方向上的模场分布,分析了带隙内两个不同的结构方向上的模场分布特性.结果表明.在长波长区域,两个方向上的模场半径并不相等,但都随波长的增加而减小,其变化规律与全内反射导光的光纤不同.     

全固双芯光子晶体光纤温度传感特性的研究

主要分析带隙型全固双芯光子晶体光纤填充高温度系数折射率敏感介质后的温度特性.应用平面波展开法和全矢量有限元法研究温度对其模场分布、有效折射率、耦合长度及温度传感的影响.理论计算结果表明,耦合长度随温度升高出现单极值或多极值点,奇模式的有效折射率随着温度的变化或波长的变化会出现跳变情况.     

光控光子晶体偏光片

提出了一种新颖的调节液晶光子晶体光子带隙的方法.光子晶体波导通过往二维三角形光子晶体的介质柱之间填充液晶得到，光诱导液晶取向以改变液晶的折射指数从而改变光子晶体的光子带隙.数值模拟结果表明：通过外界光场控制所填充的向列相液晶的方向可以对这种二维三角形介质柱光子晶体的禁带结构进行调节.与电场调制方法相比，该光控液晶取向技术具有响应速度快、结构简单的优点.这种可调光子晶体可用于制作新颖的光敏偏光片.     

光控二维光子晶体光开关

提出了一种调节液晶光子晶体光子带隙的方法。二维三角介质柱形光子晶体位于2块熔凝石英片之间,在介质柱之间填充各向同性排列的液晶,受偏振紫外光照射后,光诱导液晶分子定向排列,通过光诱导液晶分子取向改变液晶的折射率。数值模拟结果表明：通过外界光场控制所填充的向列相液晶分子的方向可以对这种二维三角形介质柱光子晶体的禁带结构进行调节。该可调光子晶体可控制波导中TM模和TE模的选择性传输,因而可应用于制作全光光开关。     

带隙型光子晶体光纤的泄露谱分析

利用光束传播法对带隙型光子晶体光纤（photonic crystal fiber, PCF）的泄露谱进行了数值分析.结果表明：PCF泄露谱往往具有多个带隙；泄露谱对PCF结构的变化异常敏感,泄露峰值波长和带隙波长不但与空气孔周期有关,还受空气孔直径的影响；由于PCF的空气孔内可填充液晶,泄露特性对液晶折射率的变化极其敏感,当液晶折射率增大时,峰值泄露波长和带隙波长都向长波漂移.     

空芯光子晶体光纤光子带隙的测量与数值模拟

用全矢量平面波法计算三角结构光子晶体光纤的带隙. 用透射法测量了自制的空芯光子晶体光纤的透射谱,得到了它在可见光波段透射强度与波长的关系,并在随后的实验中观测到了传光的模场图.通过理论模拟了实验所用的空芯光子晶体光纤的带隙图,与实验结果具有较好的一致性. 关键词： 空芯光子晶体光纤 光子带隙 全矢量平面波法 透射     

Ge30Sb8Se62硫系玻璃的制备及其10.6μm低损耗空芯光子带隙光纤的设计

硫系玻璃光子晶体光纤在中远红外激光传输领域具有广阔的应用前景。制备了红外波段具有优良透过特性的Ge30Sb8Se62硫系玻璃,并以此为基质材料设计了一种适合于高功率中红外激光传输的带隙型光子晶体光纤。利用平面波展开法和有限元法分析了不同结构下该光纤的光子带隙、模场面积和限制损耗特性。通过优化光纤的结构参数,获得了在10.6μm处限制损耗小于0.1dB/m的大模场(模场面积大于100μm2)光子晶体光纤。     

温度对液晶填充光子晶体光纤传输特性的影响

利用液晶的折射率是温度和波长函数的特性,在光子晶体光纤(PCF)芯区的空气柱中填充向列相液晶,通过改变温度来改变液晶的折射率,构成了一种温度凋制光子晶体光纤.用阶跃有效折射率模型研究了温度对这种光子晶体光纤在不同光波长时传输特性的影响,并进行了数值计算.结果表明液晶填充使光子晶体光纤的色散减小,由于折射率对温度和波长变化敏感,改变温度可以使光纤在长波长区域出现单模传输,在短波长时不会出现单模传输,即使包层相对孔径很小也不会出现无截止单模传输.温度升高使光纤的色散值增大,零色散波长向短波长方向移动.这些特性对温度调制光子晶体光纤器件的设计和应用具有一定的参考意义.     

Design of Topas microstructured fiber with ultra-flattened chromatic dispersion and high birefringence

A microstructured polymer optical fiber (mPOF) with both ultra-flattened near-zero chromatic dispersion and high birefringence based on Topas cyclic olefin copolymer is designed. Three rings of uniform elliptical air holes are arranged in triangular lattice in the cladding and an extra small defected hole is introduced in the fiber core. Guided modes, dispersion, birefringence and mode confinement properties of the designed mPOF are investigated by using the full-vector finite element method. Dispersion values between ± 0.5 ps/km/nm over the wavelength 1.1-1.7 μm and high birefringence of the order of 10⁻³ are obtained for the optimized fiber structure. Low confinement losses and small effective mode area are obtained at the same time. The relatively simple architecture of the proposed Topas mPOF can be fabricated by our extrusion-stretching techniques.     

Tunable highly birefringent photonic bandgap fibers

A novel tunable highly birefringent photonic bandgap fiber (PBGF) is designed theoretically by filling its air holes with high-index material. The transmission band can be continuously tuned by changing the refractive index of the filling material. Accordingly, the tunable modal birefringence and polarization mode dispersion of the PBGFs are investigated by adjusting the refractive index of the filling material. Furthermore, we have also analyzed the effect of surface modes in the photonic bandgap on the characteristics of the tunable PBGFs. The simulation results show the feasibility of constructing birefringence-tunable photonic crystal fibers and related fiber devices in practical applications.     

Bandwidth enhancement by differential mode attenuation in multimode photonic crystal Bragg fibers

In multimode bandgap guiding fibers higher-order modes have high radiation losses. Once excited, after a short propagation distance such modes are leaked out of the fiber core. Reduction of the number of excited modes in the fiber core leads to a decrease of intermodal dispersion and a dramatic enhancement of fiber bandwidth. Due to the increase in the propagation loss, bandwidth enhancement by differential mode attenuation also leads to the reduction of the maximal length of a usable fiber span. We demonstrate that by proper design of a photonic crystal reflector long fiber spans of high bandwidth are possible.     

Efficient antiguiding of TE and TM polarizations in low-index core waveguides without the need for an omnidirectional reflector

While an omnidirectional bandgap is necessary to reflect arbitrary polarized light with a planar periodic reflector at any angle of radiation incidence, we demonstrate that omnidirectionality is not at all necessary for efficient antiguiding of modes of any polarization in low-index core photonic bandgap (PBG) fibers and waveguides. For a given radiation decay rate into the reflector and multilayer bandgap size we characterize the phase space of fiber materials leading to the same effective guiding conditions. We demonstrate that low- and high-index-contrast PBG waveguides can antiguide problematic TM-like modes equally effectively. Finally, the possibility of TE-like guidance of a TM-polarized mode is described.     

Time-domain multimode dispersion measurement in a higher-order-mode fiber

We present a new multimode dispersion measurement technique based on the time-of-flight method. The modal delay and group velocity dispersion of all excited modes in a few-mode fiber can be measured simultaneously by a tunable pulsed laser and a high speed sampling oscilloscope. A newly designed higher-order-mode fiber with large anomalous dispersion in the LP(02) mode has been characterized using this method, and experimental results are in good agreement with the designed dispersion values. The demonstrated technique is significantly simpler to implement than the existing frequency-domain or interferometry-based methods.     

Light propagation with ultralarge modal areas in optical fibers

We demonstrate robust single-transverse-mode light propagation in higher-order modes of a fiber, with effective area A(eff) ranging from 2,100 to 3,200 microm(2). These modes are accessed using long-period fiber gratings that enable higher-order-mode excitation over a bandwidth of 94 mm with greater than 99% of the light in the desired mode. The fiber is designed such that the effective index separation between modes is always large, hence minimizing in-fiber mode mixing and enabling light propagation over lengths as large as 12 m, with bends down to 4.5 cm radii. The modal stability increases with mode order, suggesting that A(eff) of this platform is substantially scalable.     

基于高折射率液体填充的花瓣形微结构光纤可调滤模特性

提出一种新型的可调滤模光纤结构,利用纤芯模式与微结构包层形成的超模群之间的耦合实现选择性滤模,采用花瓣形包层结构使包层中传输的模式更容易产生高的泄漏损耗;提出以液体填充包层介质柱,使包层形成的超模群有效折射率区间可以通过环境温度来调节,从而达到可调选择性滤模目的.利用液体柱的LP11模所形成的超模群,有效增大了其工作带宽和温度调谐范围.数值模拟结果表明,采用长度仅为71.4 mm的滤模光纤,可以使特定的抑制模式损耗达到20 dB以上,而其他模式损耗均在1 dB以下.提出的光纤可以在少模光纤传输系统中作为滤模器使用,以降低模式转换器、复用器/解复用器以及光开关和光路由等的模式串扰.     

A stable and tunable linear polarization single longitudinal mode fiber ring laser

A stable and tunable linear polarization single longitudinal mode fiber ring laser is proposed and demonstrated. A high extinction ratio spatial mode interference filter utilizing two-mode graded-index fiber supresses irregular side modes effectively, the combination of fiber polarizer and polarization maintaining fiber act as a polarization dependent comb filter, and tunable bandpass filter is adopted to select proper lasing wavelength. The power fluctuation and wavelength fluctuation at 1549.88 nm are less than 0.05 dB and 0.02 nm in 1 h, respectively. Only one longitudinal mode appears within a free spectral range of 7.5 GHz, and the degree of polarization in percentage is approximately as high as 99.07%.     

Dynamic all-optical tuning of transverse resonant cavity modes in photonic bandgap fibers

Photonic bandgap fibers for transverse illumination containing half-wavelength microcavities have recently been designed and fabricated. We report on the fabrication and characterization of an all-optical tunable microcavity fiber. The fiber is made by incorporating a photorefractive material inside a Fabry-Perot cavity structure with a quality factor Q >200 operating at 1.5 microm. Under short-wavelength transverse external illumination, a 2 nm reversible shift of the cavity resonant mode is achieved. Dynamic all-optical tuning is reported at frequencies up to 400 Hz. Experimental results are compared with simulations based on the amplitude and kinetics of the transient photodarkening effect measured in situ in thin films.     

Highly dispersive large mode area photonic bandgap fiber

An all-silica photonic bandgap fiber composed of a low-index core surrounded by alternating high- and low-index rings allows us to achieve a large mode area (500 microm(2)) and large chromatic dispersion. Sharp resonances from the even Bragg mode to odd ring modes theoretically lead to 20,000 ps/(nm km) chromatic dispersion when large bends are applied. By nature, sharp resonances are sensitive to inhomogeneities along the fiber length. Under experimental conditions, the resonances are broadened and the dispersion coefficient is decreased to 1000 ps/(nm km). However, to the best of our knowledge, this is the largest dispersion coefficient reported using a large mode area fiber.