Six MeV proton acceleration from plasma generated by high-intensity laser using advanced thin polyethylene targets

Proton acceleration can be induced by non-equilibrium plasma developed by high-intensity laser pulses, at 10¹⁶ W/cm², irradiating different types of thin polyethylene targets. The process of proton acceleration and directive yield emission was investigated, optimizing the laser parameters, the irradiation conditions, and the target properties. The use of 600 J pulse energy, a laser focalization inducing self-focusing effects and advanced targets with embedded nanoparticles and optimal thicknesses, has permitted to accelerate forward protons up to the energies of about 6 MeV and amount of the order of 10¹⁵ H⁺/pulse. High proton energy is obtained using thin foils enriched with gold nanoparticles, whereas high proton yield is obtained using targets with a thickness of about 10 μm. The plasma diagnostics using SiC semiconductor detectors in time-of-flight configuration was fundamental to monitor the optimal conditions to improve the plasma processes concerning the ion acceleration and the X-ray and relativistic electron emission.     

Near‐3‐MeV protons from target‐normal‐sheath‐acceleration femtosecond laser irradiating advanced targets

Advanced targets based on graphene oxide and gold thin film were irradiated at high laser intensity (10¹⁸–10¹⁹ W/cm²) with 50‐fs laser pulses and high contrast (10⁸) to investigate ion acceleration in the target‐normal‐sheath‐acceleration regime. Time‐of‐flight technique was employed with SiC semiconductor detectors and ion collectors in order to measure the ion kinetic energy and to control the properties of the generated plasma. It was found that, at the optimized laser focus position with respect to the target, maximum proton acceleration up to about 3 MeV energy and low angular divergence could be generated. The high proton energy is explained as due to the high electrical and thermal conductivity of the reduced graphene oxide structure. Dependence of the maximum proton energy on the target focal position and thickness is presented and discussed.     

Experimental investigations of fast-proton production in a picosecond laser plasma

Results of experimental investigations of fast-proton production in a laser plasma are presented for the case where the intensity of laser radiation at the targets is 2 × 10¹⁸ W/cm². Three processes of fast-proton acceleration in laser plasma are investigated: (1) the acceleration of protons from the front surface toward the laser pulse, (ii) the acceleration of protons from the front surface of the target toward its interior, and (iii) the acceleration of protons from the rear foil surface in the outward direction. The activation procedure and CR-39 tracker detectors featuring a set of various-thickness aluminum filters were used to record fast protons. It turned out that the proton-acceleration process is the most efficient in the case of proton acceleration from the rear foil surface in the outward direction. Experimental results revealed that about N _p = 10⁷ protons of energy in the region E _p > 1.9 MeV that are accelerated from the target surface toward a laser ray, N _p = 4× 10⁷ protons of energy in the region E _p > 1.9 MeV that are accelerated fromthe front surface of the target toward its interior, and N _p = 4×10⁸ protons of energy in the region E _p > 1.9 MeV that are accelerated from the rear foil surface in the outward direction are generated at a laser-radiation intensity of 2 × 10¹⁸ W/cm² at the surface of aluminum, copper, and titanium targets. Experimental investigations aimed at optimizing the process of proton acceleration from the rear surface of aluminum foils were performed by varying the foil thickness over the range between 1 and 100 μm. The results of these experiments showed that there is an optimum foil thickness of 10 μm, in which case protons of maximum energy 5 MeV are generated.     

Advanced targets,diagnostics and applications of laser-generated plasmas

High-intensity sub-nanosecond-pulsed lasers irradiating thin targets in vacuum permit generation of electrons and ion acceleration and high photon yield emission in non-equilibrium plasmas. At intensities higher than 10¹⁵?W/cm² thin foils can be irradiated in the target-normal sheath acceleration regime driving ion acceleration in the forward direction above 1?MeV per charge state. The distributions of emitted ions in terms of energy, charge state and angular emission are controlled by laser parameters, irradiation conditions, target geometry and composition. Advanced targets can be employed to increase the laser absorption in thin foils and to enhance the energy and the yield of the ion acceleration process. Semiconductor detectors, Thomson parabola spectrometer and streak camera can be employed as online plasma diagnostics to monitor the plasma parameters, shot by shot. Some applications in the field of the multiple ion implantation, hadrontherapy and nuclear physics are reported.     

Ion acceleration from aluminium plasma generated by a femtosecond laser in different conditions

Non-equilibrium plasma was obtained by irradiating Al foils in vacuum with a femtosecond (fs) laser at intensities of the order of 10¹⁸ W/cm². Protons and other light ions were accelerated in the forward direction by using the target-normal-sheath acceleration regime. Time-of-flight technique was employed to measure the ions' kinetic energy using SiC detectors placed at known distances and angles. The ion acceleration was monitored under different conditions of laser focal position, laser pulse energy, and laser contrast. The target was irradiated using different thicknesses and anti-reflecting graphene films. By optimizing the laser parameters, irradiation conditions, and target properties, it was possible to accelerate up to 2.3 MeV per charge state, as will be presented and discussed.     

Dynamic imaging and hydrodynamics study of high velocity, laser-accelerated thin foil targets using multiframe optical shadowgraphy

The main aim of the study of thin target foil–laser interaction experiments is to understand the physics of hydrodynamics of the foil acceleration, which is highly relevant to inertial confinement fusion (ICF). This paper discusses a simple, inexpensive multiframe optical shadowgraphy diagnostics developed for dynamic imaging of high velocity laser-accelerated target foils of different thicknesses. The diagnostic has a spatial and temporal resolution of 12 μm and 500 ps respectively in the measurements. The target velocity is in the range of 10⁶–10⁷ cm/s. Hydrodynamic efficiency of such targets was measured by energy balance experiments together with the measurement of kinetic energy of the laser-driven targets. Effect of target foil thickness on the hydrodynamics of aluminum foils was studied for determining the optimum conditions for obtaining a directed kinetic energy transfer of the accelerated foil. The diagnostics has also been successfully used to study ablatively accelerated targets of other novel materials.     

Protons and carbon ions acceleration in the target-normal-sheath-acceleration regime using low-contrast fs laser and metal-graphene targets

fs pulsed lasers at an intensity of the order of 10¹⁸ W/cm², with a contrast of 10⁻⁵, were employed to irradiate thin foils to study the target-normal-sheath-acceleration (TNSA) regime. The forward ion acceleration was investigated using 1/11 µm thickness foils composed of a metallic sheet on which a thin reduced graphene oxide film with 10 nm thickness was deposited by single or both faces. The forward-accelerated ions were detected using SiC semiconductors connected in time-of-flight configuration. The use of intense and long pre-pulse generating the low contrast does not permit to accelerate protons above 1 MeV because it produces a pre-plasma destroying the foil, and the successive main laser pulse interacts with the expanding plasma and not with the overdense solid surface. Experimental results demonstrated that the maximum proton energies of about 700 keV and of 4.2 MeV carbon ions and higher were obtained under the condition of the optimal acceleration procedure. The measurements of ion energy and charge states confirm that the acceleration per charge state is measurable from the proton energy, confirming the Coulomb–Boltzmann-shifted theoretical model. However, heavy ions cannot be accelerated due to their mass and low velocity, which does not permit them to be subjected to the fast and high developed electric field driving the light-ion acceleration. The ion acceleration can be optimized based on the laser focal positioning and on the foil thickness, composition, and structure, as it will be presented and discussed.     

Experimental study of the acceleration of protons emitted from thin foils irradiated by ultrahigh-contrast laser pulses

Experimental results are presented for proton acceleration from the back of a target irradiated by laser pulses with intensities up to 2 × 10¹⁹ W/cm² generated by the SOKOL-P facility. The proton acceleration efficiency increases with decreasing of the target thickness. However, thin targets are destroyed by the amplified spontaneous emission (ASE) prepulse before the main pulse arrival. An additional optical switch based on a Pockels cell has been used in the amplification section to carry out the experiments with ultrathin foils. As a result, the energy contrast with respect to the ASE prepulse has been increased up to 4 × 10⁶. Owing to high contrast, the experiments on studying proton acceleration from foils with thicknesses less than 100 nm have been carried out.     

超薄靶激光质子加速实验研究

在超短超强飞秒SILEX-Ⅰ激光装置上,开展了薄膜靶激光质子加速的实验研究。实验发现激光预脉冲、靶厚度对质子加速有很大的影响。在激光强度3×1018~3×1019W/cm2条件下,采用前表面厚度为3μm铜、后表面镀4μm厚CH靶,质子的最大能量达到3.15 MeV。而对190 nm厚CH膜靶,质子的最大能量为0.54 MeV。初步研究了激光偏振对质子加速的影响,相同激光功率条件下,圆偏振激光加速产生的质子最大能量略低于P偏振打靶。这些结果与靶后鞘层加速机制相一致。     

Laser acceleration of light ions from high-intensity laser-target interactions

A systematic theoretical study of laser-irradiated targets made of material with increasing atomic number has been performed. The formation of energetic light ions resulting from the interaction of an intense ultrashort pulse laser with thin planar targets is investigated theoretically with a two-dimensional relativistic electromagnetic particle-in-cell model. A common parameter, the areal electron density of the foil, can be used to describe qualitatively targets made of different material. By varying either the laser intensity or the target thickness we observe a gradual transition of various ion acceleration mechanisms from one into another. Light ions, such as H⁺, Li³⁺, C⁶⁺, and Al¹³⁺, can be accelerated to GeV energies with existing laser systems at a laser fluence of 10–20 J/μm².     

X-Rays emission by high-intensity pulsed lasers irradiating thin foils at PALS laboratory

X-rays and forward ion emission from laser-generated plasma in the Target Normal Sheath Acceleration regime of different targets with 10-μm thickness, irradiated at Prague Asterix Laser System (PALS) laboratory at about 10¹⁶ W/cm² intensity, employing a 1,315 nm-wavelength laser with a 300-ps pulse duration, are investigated. The photon and ion emissions were mainly measured using Silicon Carbide (SiC) detectors in time-of-flight configuration and X-ray streak camera imaging. The results show that the maximum proton acceleration value and the X-ray emission yield growth are proportional to the atomic number of the irradiated targets. The X-ray emission is not isotropic, with energies increasing from 1 keV for light atomic targets to about 2.5 keV for heavy atomic targets. The laser focal position significantly influences the X-ray emission from light and heavy irradiated targets, indicating the possible induction of self-focusing effects when the laser beam is focalized in front of the light target surface and of electron density enhancement for focalization inside the target.     

Cold electrons acceleration in TNSA laser-generated plasma using a low-contrast fs laser

The fs laser facility in Bordeaux, delivering an intensity of 10¹⁸ W/cm² at normal incidence on thin foils, has been used to induce forward electron and ion acceleration in target-normal-sheath-acceleration (TNSA) regime. Micrometric thin foils with different composition, thickness, and electron density, were prepared to promote the charge particle acceleration in the forward direction. The plasma electron and ion emission monitoring were performed on-line using SiC semiconductor detectors in time-of-flight (TOF) configuration and gaf-chromics films both covered by thin absorber filters. The experiment has permitted to accelerate electrons and protons. A special attention was placed to detect relativistic hot electrons escaping from the plasma and cold electrons returning to the target position. The electron energies of the order of 100 keV and of about 1 keV were detected as representative of hot and cold electrons, respectively. A high cold electron contribution was measured using low-contrast fs laser, while it is less evident using high-contrast fs lasers. The charge particle acceleration depends on the laser parameters, irradiation conditions, and target properties, as will be presented and discussed.     

激光驱动飞片过程中激光烧蚀深度的计算

利用激光体烧蚀模型,数值模拟了激光驱动飞片的加速过程,包括激光的吸收和飞片的速度历史等。在光强为GW/cm2量级的激光作用下,激光烧蚀产生的等离子体的流体力学运动可用改编的1维La-grange流体力学计算程序SSS来描述。通过计算得到不同激光能量下的飞片密度剖面,由此给出金属薄膜的烧蚀深度与实验测量值进行比对,二者符合得较好。     

飞秒激光中高能质子的产生与加速的研究

为了探索飞秒激光与固体靶相互作用中高能质子的产生和加速机制,在超短超强激光装置“SILEX-I”上进行了飞秒激光与平面固体薄膜Cu靶的相互作用中高能质子空间分布、能谱和产额的实验研究。实验采用固体核径迹探测器CR39和Thomson离子谱仪相结合的方式,在固体靶背表面法线方向测量了质子空间分布、能谱和产额。实验结果表明：质子沿着靶背法线方向发射,质子空间分布呈圆环状,存在一定的立体角;质子在一定能量处出现截断;截断能量的大小与靶厚度有关。经分析,高能离子的产生和加速是多种作用机制共同作用的结果,其中静电场中的TNSA加速机制则占主导地位。     

飞秒激光中高能质子的产生与加速的研究

为了探索飞秒激光与固体靶相互作用中高能质子的产生和加速机制,在超短超强激光装置“SILEX-I”上进行了飞秒激光与平面固体薄膜Cu靶的相互作用中高能质子空间分布、能谱和产额的实验研究。实验采用固体核径迹探测器CR39和Thomson离子谱仪相结合的方式,在固体靶背表面法线方向测量了质子空间分布、能谱和产额。实验结果表明：质子沿着靶背法线方向发射,质子空间分布呈圆环状,存在一定的立体角;质子在一定能量处出现截断;截断能量的大小与靶厚度有关。经分析,高能离子的产生和加速是多种作用机制共同作用的结果,其中静电场中的TNSA加速机制则占主导地位。     

Proton beam generation by ultra-high intensity laser–solid interaction

We report on some recent experimental results on proton production from ultra-intense laser pulse interaction with thin aluminium and plastic foil targets. These results were obtained at Laboratoire d'Optique Appliquée with the 100 TW ‘salle jaune’ laser system, delivering 35 fs laser pulses at 0.8 μm, reaching a maximum intensity on target of a few 10¹⁹ W/cm².

In such extreme interaction conditions, an intense and collimated relativistic electron current is injected from the plasma created on the laser focal spot into the cold interior of the target. Its transport through dense matter, ruled by both collisions and self-induced (electro-magnetic) field effects, is the driving mechanism for proton acceleration from the rear side of thin foils: when reaching and leaving the foil rear-side, the fast electrons create a large charge separation and a huge electrostatic field with a maximum value of few TV/m, capable of accelerating protons.

A parametric study as a function of the laser driver and target parameters indicates an optimal value for target thickness, which strongly depends on the laser prepulse duration. In our experiments, we did irradiate targets of various materials (CH, Al, Au) changing the prepulse duration by using fast Pockels cells in the laser chain. CR-39 nuclear track detectors with Al filters of different thickness and a Thomson parabola were used to detect proton generation. The best results were obtained for 2 μm Al targets, leading to the generation of proton energies with energies up to 12 MeV.     

Investigation of the effect of plasma waves excitation on target normal sheath ion acceleration using fs laser‐irradiating hydrogenated structures

Measurements of ion acceleration in polymethylmethacrylate foils covered by a thin copper film irradiated by fs laser in target normal sheath acceleration regime are presented. The ion acceleration depends on the laser parameters, such as the pulse energy; depends on the irradiation conditions, such as the focal point position of the laser with respect to the target surface; and depends on the target properties, such as the metallic film thickness. The proton acceleration increases in the presence of the metallic film enhancing the plasma electron density, reaching about 1.6 MeV energy for a focal position on the target surface. The plasma diagnostics uses SiC detectors, absorber foils, Faraday cups, and gafchromic films. Employing p‐polarized laser light and a suitable oblique incidence, it is possible to increase the proton acceleration up to about 2.0 MeV thanks to the effects of laser absorption resonance due to plasma waves excitation.     

Laser-driven proton acceleration and applications: Recent results

The acceleration of high-energy ion beams following the interaction of short (t < 1 ps) and intense (Iλ² > 10¹⁸ W cm^-2 μm²) laser pulses with solid targets is a field of research currently attracting high interest in the scientific community, due to some of the unique properties of these ion sources, promising routes toward the optimization of their energy content, and a number of possible, innovative applications in the scientific, technological and medical areas. Work on the characterization and development of these sources has progressed enormously over the past few years, thanks to the contribution of many groups worldwide. This paper will report some recent results, obtained in experiments carried out at the RAL and LULI laboratories, in which we investigated the ion acceleration mechanism, developed a technique to control the ion beam divergence and energy spectrum, and applied a proton radiography technique to investigate electric and magnetic field production following laser-matter interaction.     

2.5-MeV neutron source controlled by high-intensity pulsed laser generating plasma

A laptop neutron source suited for the most demanding field or laboratory applications is presented. It is based on laser ablation of CD₂ primary targets, plasma acceleration of the D⁺ ions, and their irradiation of secondary CD₂ targets. The deuterium–deuterium (D-D) fusion reaction is induced in the secondary target, according to the values of fusion cross-section versus deuteron energy, which show a significant probability also at relatively low ion energies. The experiments were completed in the PALS laboratory, Prague, detecting monoenergetic neutrons at 2.45 MeV with an emission flux of about 10⁹ neutrons per laser shot. Other experiments demonstrating the possibility to induce D-D events were performed at IPPLM, Warsaw, and at INFN-LNS, Catania, where the deuterons were accelerated at about 4 MeV and 50 keV, respectively. In the last case, a low laser intensity and a post-ion acceleration system were employed. A special interaction chamber, under vacuum, is proposed to develop a new source of monochromatic neutrons or thermalized distribution of neutrons     

Energy analysis of protons emitted from Nd:YAg laser-generated plasmas

Hydrogenated targets have been irradiated in vacuum with the pulsed Nd:YAg laser at intensities of the order of 10¹⁰ W/cm². The laser-generated plasma, produced by the interaction with the solid, emits protons and other ions along the normal to the target surface. Ion collectors and ion energy analyzer were used to measure the current, the angular emission and the energy distributions of the emitted protons. Time-of-flight measurements, Coulomb–Boltzmann-distributions and the fits of experimental data were also used in order to evaluate the equivalent ion plasma temperature and the ion acceleration developed in the non-equilibrium-pulsed plasma.