Morphological, mechanical, corrosion and hydrogen permeation characteristics of Ni-nano-TiO2 composite coating compared to Ni electrodeposited on low carbon steel

Ni and Ni-nano-TiO₂ composite coatings with various amounts of TiO₂ in electrolyte, on low carbon steel, have been prepared from Watts-bath using electrodeposition process. The morphological, mechanical, corrosion and hydrogen permeation characteristics of Ni and Ni-nano-TiO₂ coatings were studied and compared with each other. The results revealed that, existence of nano-TiO₂ particles in Ni matrix improved the microstructure as well as microhardness, whereas increasing particle incorporation from 4.33 to 7.62 vol % concluded to microhardness enhancement. The corrosion behavior of Ni and Ni-nano-TiO₂ composite coatings with various amount of particle content was studied by the anodic polarization curves in 5% H₂SO₄ solution at room temperature. It was seen Ni-nano-TiO₂ composite coatings exhibited higher corrosion resistances comparing to pure Ni coating and corrosion protection improved with increasing nano-TiO₂ in coatings. In addition to the corrosion and engineering properties, comparison of hydrogen permeation characteristics of the Ni coating was made with Ni-nano-TiO₂ composite coating through Devanthan-Stachurski hydrogen permeation test. From the resulting data analysis, Ni-nano-TiO₂ composite coating was seen not only to provide longer life under corroding media, but also reduces greatly the risk of the substrate being exposed to hydrogen permeation when compared to electrodeposited Ni coating.     

Effect of the dispersibility of ZrO2 nanoparticles in Ni-ZrO2 electroplated nanocomposite coatings on the mechanical properties of nanocomposite coatings

ZrO₂ nanoparticles was uniformly co-deposited into a nickel matrix by electroplating of nickel from a Watts bath containing particles in suspension which were monodispersed with dispersant under DC electrodeposition condition. It was found that morphology, orientation and hardness of the nanocomposite coatings with monodispersed ZrO₂ nanoparticles had lots of difference from the nanocomposite coatings with agglomerated ZrO₂ nanoparticles and pure nickel coatings. Especially, the result of hardness showed that only a very low volume percent (less than 1 wt.%) of monodispered ZrO₂ nanoparticles in Ni-ZrO₂ nanocomposite coatings would result in higher hardness of the coatings. The hardness of Ni-ZrO₂ nanocomposite coatings with monodispersed and agglomerated ZrO₂ nanoparticles were 529 and 393 HV, respectively. The hardness value of the former composite coatings was over 1.3 times higher than that of the later. All these composite coatings were two-three times higher than that of pure nickel plating (207 HV) prepared under the same condition. The strengthening mechanisms of the Ni-ZrO₂ nanocomposite coatings based on a combination of grain refinement strengthening from nickel matrix grain refining and dispersion strengthening from dispersion state of ZrO₂ nanoparticles in the coatings.     

Electrodeposition and tribological properties of Ni-SrSO4 composite coatings

Ni-SrSO₄ composite coatings were electrodeposited on superalloy Inconel 718 from a Watts electrolyte containing a SrSO₄ suspension. Ni-SrSO₄ coatings were investigated by scanning electron microscope, microhardness tester, and friction and wear tester in sliding against a bearing steel ball under unlubricated condition. The incorporation of SrSO₄ into Ni matrix increases the microhardness of electrodeposited coatings. Ni-SrSO₄ composite coating exhibits a distinctly low friction coefficient and a small wear rate as contrasted with pure Ni coating and the substrate. The effect of SrSO₄ particles on microstructure and tribological properties of Ni-SrSO₄ composite coatings is discussed.     

Friction and wear properties of the co-deposited Ni-SiC nanocomposite coating

Ni-SiC nanocomposite coatings were produced by electrodeposition from a nickel sulfate bath containing SiC nanoparticles with an average particle size of 30 nm. The characteristics of the coatings were assessed by scanning electron microscopy and microhardness test. The friction and wear performance of Ni-SiC nanocomposite coatings and Ni film were comparatively investigated sliding against Si₃N₄ ceramic balls under non-lubricated conditions. The results indicated that compared to Ni film, Ni-SiC nanocomposite coating exhibited enhanced microhardness and wear resistance. The effect of SiC nanoparticles on the friction and wear resistance is discussed in detail.     

Preparation and characterization of nickel nano-Al2O3 composite coatings by sediment co-deposition

Ni-Al₂O₃ composite coatings were prepared by using sediment co-deposition (SCD) technique and conventional electroplating (CEP) technique from Watt's type electrolyte without any additives. The microstructure, hardness, and wear resistance of resulting composites were investigated. The results show that the incorporation of nano-Al₂O₃ particles changes the surface morphology of nickel matrix. The preferential orientation is modified from (2 0 0) plane to (1 1 1) plane. The microhardness of Ni-Al₂O₃ composite coatings in the SCD technique are higher than that of the CEP technique and pure Ni coating and increase with the increasing of the nano-Al₂O₃ particles concentration in plating solution. The wear rate of the Ni-Al₂O₃ composite coating fabricated via SCD technique with 10 g/l nano-Al₂O₃ particles in plating bath is approximately one order of magnitude lower than that of pure Ni coating. Wear resistance for SCD obtained composite coatings is superior to that obtained by the CEP technique. The wear mechanism of pure Ni and nickel nano-Al₂O₃ composite coatings are adhesive wear and abrasive wear, respectively.     

Fortification of Ni–Y<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocomposite coatings prepared by pulse and direct current methods

Ni–Y₂O₃ nanocomposite coatings were prepared under direct current (DC) and pulse current (PC) using acetate bath. The microstructure and corrosion resistance of the coatings were characterized by means of XRD, SEM, AFM, and EIS. The results showed that the microstructure and performances of the coatings were greatly affected by Y₂O₃ content on the deposits prepared by DC and PC methods. The microhardness and corrosion resistance were enhanced in the optimum percentage of Y₂O₃ composite coatings. The PC composite coatings were exhibited compact surface, higher microhardness, and good corrosion resistance compared with that of the DC composite coatings.     

Ni-Co-TiO2 nanocomposite coating prepared by pulse and pulse reversal methods using acetate bath

Ni-Co/nano TiO₂ (Ni-Co-TiO₂) composite coatings were prepared under pulse current and pulse reverse current methods using acetate bath. The microstructure and corrosion resistance of the coatings were characterized by means of XRD, SEM and EIS. Both the Ni-Co alloy and composite coatings exhibited single phase of Ni matrix with face centered cubic (fcc) crystal structure. The crystal orientation of the Ni-Co-TiO₂ composite coating was transformed from crystal face (2 0 0) to (1 1 1) compared with Ni-Co alloy coatings. The results showed that the microstructure and performances of the coatings were greatly affected by TiO₂ content on the deposits prepared by PC and PRC methods. The microhardness and corrosion resistance were enhanced in the optimum percentage of TiO₂ composite coatings. The PRC composite coatings were exhibited from compact surface, higher microhardness and good corrosion resistance compared with that of the PC composite coating.     

Investigation on corrosion and wear behaviors of nanoparticles reinforced Ni-based composite alloying layer

In order to investigate the role of amorphous SiO₂ particles in corrosion and wear resistance of Ni-based metal matrix composite alloying layer, the amorphous nano-SiO₂ particles reinforced Ni-based composite alloying layer has been prepared by double glow plasma alloying on AISI 316L stainless steel surface, where Ni/amorphous nano-SiO₂ was firstly predeposited by brush plating. The composition and microstructure of the nano-SiO₂ particles reinforced Ni-based composite alloying layer were analyzed by using SEM, TEM and XRD. The results indicated that the composite alloying layer consisted of γ-phase and amorphous nano-SiO₂ particles, and under alloying temperature (1000 °C) condition, the nano-SiO₂ particles were uniformly distributed in the alloying layer and still kept the amorphous structure. The corrosion resistance of composite alloying layer was investigated by an electrochemical method in 3.5%NaCl solution. Compared with single alloying layer, the amorphous nano-SiO₂ particles slightly decreased the corrosion resistance of the Ni-Cr-Mo-Cu alloying layer. X-ray photoelectron spectroscopy (XPS) revealed that the passive films formed on the composite alloying consisted of Cr₂O₃, MoO₃, SiO₂ and metallic Ni and Mo. The dry wear test results showed that the composite alloying layer had excellent friction-reduced property, and the wear weight loss of composite alloying layer was less than 60% of that of Ni-Cr-Mo-Cu alloying layer.     

Electrochemical deposition and tribological behaviour of Ni and Ni-Co metal matrix composites with SiC nano-particles

Metal matrix composites reinforced with nano-sized particles have attracted scientific and technological interest due to the enhanced properties exhibited by these coatings. Ni-SiC composites have gained widespread application for the protection of friction parts in the automobile industry. The influence of variables like SiC content, current density and stirring speed on microhardness of nano-composite coatings has been studied. The improved microhardness was associated with the reduction in crystallite size determined by X-ray diffraction studies. The influence of incorporation of nano-SiC in hardened Ni-Co alloy matrix was also studied. It was observed that for 28 wt.% Co content in the matrix the microhardness was higher compared to 70 wt.% for a given nano-SiC content. This was associated to the crystal phase of Ni-28Co-SiC being fcc compared to hcp phase exhibited by Ni-70Co-SiC. The wear resistance of pure Ni, Co and nano-composite coatings was studied using pin-on-disc wear tester under dry sliding condition. The volumetric wear loss indicated that, the wear resistance of Ni-SiC nano-composite is better than that of pure nickel deposit. The wear resistance of Ni-Co composites was observed to be superior to Ni composite. The wear behaviour of Ni and Ni-28Co composite was in accordance with the Archard's law. However, the superior wear characteristic exhibited by Ni-70Co-SiC composite followed the reverse Archard's behaviour.     

Zn-ZrO2 nanocomposite coatings: Elecrodeposition and evaluation of corrosion resistance

The Zn and Zn-ZrO₂ composite coatings were produced by electrodeposition technique using sulphate bath. ZrO₂ particles were characterized using scanning electron microscopy (SEM) and X-ray diffraction (XRD). The ZrO₂ particle size distribution in the plating bath and Zeta potential and the ZrO₂ were measured using dynamic light scattering technique (DLS). The corrosion resistance properties of Zn and Zn-ZrO₂ composite coatings were compared by examining the experimental data acquired through polarization, open circuit potential (OCP) and Tafel measurements. The corrosion environment was 3.5 wt% NaCl solution. The variation of amount of ZrO₂ in the solution on their % wt inclusion in the composite and on composite microhardness was investigated. XRD patterns were recorded for Zn and Zn-ZrO₂ coatings to compare their grain size. The SEM images of coatings before and after corrosion under chemical and electrochemical conditions were presented. The results were analyzed to establish the superiority of Zn-ZrO₂ composite over Zn coating.     

Electrodeposition and properties of Zn-nanosized TiO2 composite coatings

Nanosized TiO₂ particles were prepared by sol-gel method. The TiO₂ particles were co-deposited with zinc from a sulphate bath at pH 4.5 using electrodeposition technique. The corrosion behavior of the coatings was assessed by electrochemical polarization, impedance, weight-loss and salt spray tests. Wear resistance and microhardness of the composite coating was measured. The smaller grain size of the composite coatings was observed in the presence of TiO₂ and it was confirmed by the images of scanning electron microscopy (SEM) and X-ray diffraction (XRD) techniques.     

Fabrication of high-performance nickel/graphene oxide composite coatings using ultrasonic-assisted electrodeposition

Ultrasonic-assisted electrodeposition was used to fabricate the nickel/graphene oxide composite coatings with high hardness, low friction coefficient, and high wear resistance. In the present study, the effects of ultrasonic power and concentration of graphene oxide on the mechanical and tribological properties of the electrodeposited nickel/graphene oxide composite coatings were systematically studied. X-ray diffraction (XRD) analyses showed that the crystallite size of the nickel decreased with an increase of ultrasonic power (0–50 W, 40 KHz, square wave) and concentration of graphene oxide (0.1–0.4 g/L). Morphologies of the surface and cross-section of the composite coatings observed by Scanning Electron Microscopy (SEM) confirmed the existence of graphene oxide particles in the nickel matrix. The results from microhardness measurement demonstrated that the hardness was increased by 1.8 times using 50 W ultrasonic-assisted electrodeposition with the fixed concentration of graphene oxide (0.1 g/L), compared to the pure nickel coating. The hardness was increased by 4.4 times for the 0.4 g/L graphene oxide with the optimized ultrasonic power of 50 W in comparison to the pure nickel coating. Meanwhile, the friction coefficient decreased gradually with an increase in ultrasonic power and concentration of graphene oxide, respectively, where the effect of the concentration of graphene oxide played a more important role.     

Fabrication and characterization of Au/SiO2 nanocomposite films grown by radio-frequency cosputtering

Au/SiO₂ nanocomposite films were prepared on Si wafers by cosputtering of SiO₂ and gold wires. Au/Si atomic ratios in Au/SiO₂ nanocomposite films were varied from 0.53 to 0.92 by controlling the length of gold wire to study the evolution of the crystallization of gold, the size of Au/SiO₂ nanocomposite particles, and the optical properties of as-deposited Au/SiO₂ nanocomposite films. An X-ray photoelectron spectroscopy reveals that Au exists as a metallic phase in the bulk of SiO₂ matrix. Dome-shaped Au/SiO₂ nanocomposite particles and both Au (1 1 1) and (2 0 0) planes were observed in a field-emission scanning electron microscopy and X-ray diffraction studies respectively. With an ultraviolet-visible, absorption peaks of Au/SiO₂ nanocomposite films were observed at 525 nm.     

Ultrasonic-assisted electrodeposition of Ni/diamond composite coatings and its structure and electrochemical properties

Ni/diamond composite coatings have been synthesized by ultrasonic-assisted electrodeposition in a Ni electroplating bath containing diamond nanoparticles. The influences of current density and ultrasonic agitation on the coating composition, morphology, topography, phase structure, and electrochemical characteristics of the electrodeposits were evaluated. Ultrasonic agitation was provided using an external ultrasonic bath at a frequency of 40 kHz and acoustic power of 300 W. Coating samples were also prepared under magnetic stirring for comparison with the ultrasonic-assisted deposits. This work reveals that the diamonds have been incorporated and evenly distributed in the composites. The coatings exhibit dense, granular like morphology with pyramid-like grains. As current density increases, the diamond amount of ultrasonic-assisted electrodeposits first increased to maximum of 11.4 wt% at 3 A dm⁻² and then decreases to 9.9 wt% at 5 A dm⁻², and the RTC of the preferred orientation (2 0 0) plane increases from 76.3% up to 93.4%. The crystallite size was 60–80 nm and the R_a of the magnetic and ultrasonic agitations were 116 nm, 110 nm, respectively. The maximum R_p of 39.9, 50.3 kΩ cm² was obtained at 4 A dm⁻² when respectively immersed 30 min and 7 days, illustrating the best corrosion resistance of the coatings of 4 A dm⁻². The effects of mechanical and ultrasonic agitations on the mechanism of the co-electrodeposition process were both proposed. The incorporation of diamond particles enhances the hardness and wear-resisting property of the electrodeposits. The ultrasonic-assisted electrodeposited Ni/diamond coating has better corrosion resistance than that prepared under mechanical stirring conditions.     

Effects of pulse electrodeposition parameters on the properties of Ni-TiO2 nanocomposite coatings

The aim of this study is to investigate the effects of pulse electrodeposition parameters on the properties of nickel-titania composite coatings electrodeposited from a nickel Watts type bath. The effects of average current density, frequency and duty cycle on the surface morphology, crystal size, preferred orientation of the deposits and the amount of embedded nano-TiO₂ particles in the composite coatings were investigated. The results represented the optimum amount of average current density (e.g., 4 A dm⁻²) for obtaining the highest volume percentage of the incorporated titania particles and subsequently the maximum microhardness. Moreover, by increasing the frequency up to 10 Hz while reducing the duty cycle to 10% at constant peak current density, the volume percentage of particles increased to about 7% which is almost twice as much the volume percentage as deposited particles in direct current method. According to the results the composite coating exhibited obviously [1 0 0] + [2 1 1] as preferred orientation at low pulse frequency and the diffraction intensity of the [2 1 1] fiber orientation is increased, probably due to the pH increase adjacent to the electrolyte/cathode interface at higher frequencies. Also, it has been found that by reduction in the duty cycle, more titania particles were incorporated in the composite coatings and this promoted the nickel crystals growth on [1 0 0] planes and consequently the coatings preferred orientation changed from the [2 1 1] to [1 0 0] + [2 1 1] planes.     

Preparation and Characterization of Nanostructured Ni-TiN Composite Films

在悬浮有TiN纳米颗粒的镍镀液中,采用直流电镀方法制备了Ni-TiN纳米复合镀层. 采用原子力显微镜、X射线衍射仪和透射电镜等手段对镀层结构、表面形貌、耐蚀性能、硬度和热稳定性等进行了研究,并且与传统镍镀层的相应性能进行了比较. 结果表明,复合镀层在耐腐蚀性、硬度和热稳定性等方面都比传统镍镀层有了显著提高;由于电流密度对阴极析氢和镍晶粒的成核/生长速率的影响,Ni-TiN纳米复合镀层的硬度随着电镀电流密度的增加而轻微减小.     

Enhanced photoluminescence of ZnO-SiO2 nanocomposite particles and the analyses of structure and composition

Stable blue-green photoluminescent ZnO-SiO₂ nanocomposite particles exhibiting quantum efficiency as high as 34.8% under excitation at 360 nm were prepared using a spray-drying process from a feed solution that contained both luminescent ZnO nanoparticles synthesized by a sol-gel method and commercially-available SiO₂ nanoparticles. The effects of silica nanoparticle size and SiO₂-to-ZnO concentration ratio on the PL properties of the composite particles were investigated. The internal structure and chemical composition were investigated in detail using elemental mapping, which revealed that ZnO nanoparticles were well-dispersed within silica nanoparticle matrix. At a LiOH concentration of 0.23 M, the predicted ZnO crystallite diameter before and after spray drying was approximately constant at 3.3 and 3.6 nm, respectively. This result indicates that ZnO particle growth was inhibited and therefore the PL property of ZnO nanoparticles was stably preserved in the composite.     

Composite Ni-Co-fly ash coatings on 5083 aluminium alloy

Ni-Co-fly ash coatings were deposited on zincate treated 5083 wrought aluminium alloy substrates with the aid of the electrodeposition technique. Structural and chemical characterization of the produced composite coatings was performed with the aid of X-ray diffraction (XRD), scanning electron microscopy (SEM) and electron dispersive X-ray analysis (EDS) techniques. The Ni-Co-fly ash coatings were found to consist of a crystalline Ni-Co solid solution with dispersed fly ash particles. In addition, chemical analysis of the Ni-Co matrix showed that it consisted of 80 wt.% Ni and 20 wt.% Co. The co-deposition of fly ash particles leads to a significant increase of the microhardness of the coating. The corrosion behaviour of the Ni-Co-fly ash/zincate coated aluminium alloy, in a 0.3 M NaCl solution (pH = 3.5), was studied by means of potentiodynamic corrosion experiments.     

Mechanical properties and wear and corrosion resistance of electrodeposited Ni-Co/SiC nanocomposite coating

Ni-Co/SiC nanocomposite coatings with various contents of SiC nano-particulates were prepared by electrodeposition in a Ni-Co plating bath containing SiC nano-particulates to be co-deposited. The influences of the nanoparticulates concentration, current density, stirring rate and temperature of the plating bath on the composition of the coatings were investigated. The shape and size of the SiC nano-particulates were observed and determined using a transmission electron microscope. The polarization behavior of the composite plating bath was examined on a PAR-273A potentiostat/galvanostat device. The wear behavior of the Ni-Co/SiC nanocomposite coatings was evaluated on a ball-on-disk UMT-2MT test rig. The worn surface morphologies of the Ni-Co/SiC nanocomposite coatings were observed using a scanning electron microscope. The corrosion behavior of the nanocomposite coatings was evaluated by charting the Tafel curves of the solution of 0.5 mol L⁻¹ NaCl at room temperature. It was found that the cathodic polarization potential of the composite electrolyte increased with increasing SiC concentration in the plating bath. The microhardness and wear and corrosion resistance of the nanocomposite coatings also increased with increasing content of the nano-SiC in the plating bath, and the morphologies of the nanocomposite coatings varied with varying SiC concentration in the plating bath as well. Moreover, the co-deposited SiC nano-particulates were uniformly distributed in the Ni-Co matrix and contributed to greatly increase the microhardness and wear resistance of the Ni-Co alloy coating.     

Effect of NaAlO2 concentrations on microstructure and corrosion resistance of Al2O3/ZrO2 coatings formed on zirconium by micro-arc oxidation

In this study, Al₂O₃/ZrO₂ composite coatings were prepared on Zr substrates by micro-arc oxidation (MAO) in the NaAlO₂-containing electrolytes, and the effect of NaAlO₂ concentration on the microstructure, bond strength, microhardness and corrosion resistance of coatings was systematically investigated. The study reveals that the adequate NaAlO₂ in the electrolyte (>0.2 M) is essential to the formation of needle-like α-Al₂O₃ in the coatings, and the amount of α-Al₂O₃ rises with the increase of the NaAlO₂ concentration. m-ZrO₂ and t-ZrO₂ are present in all of the coatings, but their relative amount largely depends on the amount of Al₂O₃. It is also found that as the NaAlO₂ concentration increases from 0.2 to 0.3 M, the coating becomes denser and thicker, and its bond strength, maximum microhardness and corrosion resistance increases as well. The coating formed at 0.3 M NaAlO₂ demonstrates the highest bond strength of 52 MPa, the maximum microhardness of 1600 Hv_0.2N and the superior corrosion resistance. However, the overhigh concentration of NaAlO₂ (0.35 M) is found harmful to the coating's microstructure and properties.