对称单负介质包层平面波导的模式特征

系统研究了负μ材料(MNG)作为包层的对称三层平板波导的传输特性. 研究发现,这种波导既支持快波的传播,又支持TE₀,TE₁模式的慢波传输. 其模式特性不同于左手介质波导和传统介质波导,导模存在的模折射率范围要比它们的大. MNG波导的TE₀快波模缺失,且TE_m模(m>1)的传播常数大于TM_m模的传播常数. TE_m模具有双模特征,且与波导的结构参数密切相关,导致波导中的净能流出现负值. 关键词： 单负介质 平板波导 快波与慢波 传播常数     

非对称金属包覆左手介质平板波导的微扰分析

基于微扰方法分析非对称金属包覆左手介质平板波导的特性,给出了该波导的复有效折射率的一级近似解,并对波导的传输特性和损耗特性进行了数值模拟.结果表明:非对称金属包覆左手介质平板波导没有零阶模式;TE1模传播系数随波导厚度的增加迅速减小,损耗系数随波导厚度的增加快速增加,达到最大值后又迅速减小;非对称金属包覆左手介质平板波导传输特性相对于左手介质三层平板波导传输特性发生了很大改变,TM1模,TM2和 TE2模式以及更高阶模式在截止厚度附近出现双值现象;特别在二阶及高阶模式中,TE模式相对于TM模式具有高传输低损耗的特性,而以右手介质为芯层的金属包覆波导不具有这一特性.     

对称金属包覆介质波导中的表面模

本文用角度扫描衰减全反射(ATR)方法系统地测量了用棱镜耦合的对称金属(Ag)包覆的介质(MgF_2)波导中TM_0模和TM_1模的传播常数及损耗与介质层厚度的关系,实验结果与理论计算相符。     

非对称金属包覆左手介质平板波导的微扰分析

基于微扰方法分析非对称金属包覆左手介质平板波导的特性,给出了该波导的复有效折射率的一级近似解,并对波导的传输特性和损耗特性进行了数值模拟.结果表明：非对称金属包覆左手介质平板波导没有零阶模式|TE1模传播系数随波导厚度的增加迅速减小,损耗系数随波导厚度的增加快速增加,达到最大值后又迅速减小|非对称金属包覆左手介质平板波导传输特性相对于左手介质三层平板波导传输特性发生了很大改变,TM1模,TM2和 TE2模式以及更高阶模式在截止厚度附近出现双值现象|特别在二阶及高阶模式中,TE模式相对于TM模式具有高传输低损耗的特性,而以右手介质为芯层的金属包覆波导不具有这一特性.     

1.5μm Ti:LiNbO_3光波导TE_0模偏振器

在1.523μm波长He-Ne激光,对于Z切Ti扩散LiNbO_3光波导及其带有金属包覆/介质缓冲层的偏振器结构,理论上计算了单模波导的工艺参数和基模的吸收损耗系数.文中用TM_0模的共振吸收效应,在1.5μm波长首次研制成Ti:LiNbO_3光波导TE_0模偏振器.当器件长度为2mm和9mm时,其消光比分别为20dB和25dB.     

对称平板漏波导中的非线性导波

本文从平面波理论出发,研究了薄膜为非线性介质的对称平板漏波导的TE_0模传输特性.计算结果表明,膜厚大于一临界值时,不存在稳定的TE_0模,膜厚小于临界值时,最多能存在两种峰值场强的TE_0模.膜厚越小,两种峰值场强相差越大.     

五层MOS光波导TE模光学特性的简化分析

应用一种简化的方法对五层MOS光波导的光学特性进行了分析,给出了TE模传播常数和吸收损耗系数的近似计算公式,并结合计算结果检验了本方法及公式的精度,为实现波导中TE_0模低损耗单模传输,讨论了某些波导参量的选择.     

用八孔耦合器识别TM0_(1)/TE_(11)混模中TE_(11)模式的方法北大核心CSCD

在高功率微波传输系统中,为了提高功率容量和效率,往往采用过模波导,因此圆波导中往往出现TM_(01)和TE_(11)混合模式的情况。采用角向均匀分布的8孔圆波导耦合器,对提取TE_(11)模式的混合比和极化角度的方法进行了分析和研究。分析了圆波导中TM_(01)和TE_(11)模式在耦合孔处的电场分布,并采用CST对各耦合孔的输出功率进行了模拟计算,得出相互正对的耦合孔的平均功率与8个孔的平均功率之比与模式之间的相位差无关的结论。同时,发现该比值与TE_(11)模式的混合比成线性关系,线性关系中的比例系数是极化角度线性函数。通过线性拟合获得了计算TE_(11)模式混合比和极化方向的表达式。与仿真设定的参数相比,用该表达式计算的结果表明,在TE_(11)模式混合比小于30%时,用其计算TE_(11)模式的混合比和极化角度是可行的,误差不超过10%。在此基础上,给出了实际情况下TE_(11)模式信息的具体判断方法。     

基于Drude-FDTD算法的单负介质组合填充波导传播特性研究

提出了电单负介质和磁单负介质组合填充矩形波导结构,通过理论分析和修正的3D-Drude-FDTD算法进行数值仿真,分析了电磁波在其中的传播特性.仿真结果表明,新结构波导中存在异于传统介质填充波导的亚波长导模,且传播常数基本不随频率的变化而变化,可以用于宽带微波器件和天线的设计. 关键词： 单负介质 传播常数 截止频率 时域有限差分法     

含左手材料对称三层平板空气波导的模式特性

研究了左手材料作为衬底及覆盖层的对称三层平板空气波导的传输特性.快波和慢波都可以在这种波导中传播.快波不存在基模模式,只有0阶和1阶的TE或TM模才会出现慢波.当左手材料的相对介电常量和相对磁导率相等时,TE、TM模式完全简并,当其相异时简并消除.可以存在同阶模式的双传播模.     

转移矩阵法在负折射率介质材料平板波导中的应用研究

利用严格电磁理论，推导出了适用于负折射率介质材料光波导的转移矩阵，分析讨论了转移矩阵的性质和应用.利用转移矩阵方法，推导出导波层为负折射率介质材料、覆盖层和衬底为右手材料的三层对称介质光波导的本征色散方程.用图解法研究了负折射率介质波导中TE波的异常色散特性.在负折射材料介质波导中没有零阶模，最低阶为1阶模，并且有截止频率,只有波导参量满足一定条件的时候才会存在，导模的横向波数可以为实数和纯虚数，而正折射率介质波导导模的横向波数只能为实数.     

Transmission properties of asymmetric slab waveguides with left-handed materials

A new dielectric slab waveguide with a left-handed material (LHM) cover and substrate is proposed. The dispersion relations and normalized effective thickness of the asymmetric LHM slab waveguide are investigated, in view of the normalized parameters. A number of unusual properties are found, for example, the fundamental and first-order modes do not exist and higher-order modes have double degeneracy. The propagation modes are absent at the low normalized frequency, and the cutoff frequencies of some LHM slab waveguide modes decrease with increase in the asymmetry measure. Unlike traditional slab waveguides, the V –H curves of the LHM slab waveguides are in one-to-one correspondence. Both TE and TM modes are discussed; in addition, the dispersion relations and normalized effective thicknesses of the TM modes are discussed in detail, when the difference in refractive indices of the film and the substrate is small. The results show that the region of mode coexistence taking place near the cutoff frequency becomes narrower with increase in the difference in refractive indices of the film and the substrate. The influence of this difference on the normalized effective thickness curves is different, and becomes smaller and smaller with increase in the value of the asymmetry measure, if different values of the refractive indices are employed.     

含单负材料的不对称平板波导的传导模

利用图解法系统地研究了由不同类型的单负材料作为包层的三层平板波导的模式特征.研究表明单负介质波导具有一系列奇异的特性,与传统介质波导或左手介质波导相比,此波导的芯区横向振荡导模的模折射率范围较大.除0阶导模外,其它TE,TM导模均为芯区横向振荡模,且同阶的TE、TM模的色散曲线几乎重合,只有0阶的TE,TM模才可以支持表面波的传播.单负介质的结构参数对0阶导模的影响较大.一定条件下,波导中可以出现0阶导模的完伞缺失或仅支持表面波的传输,还会出现超慢波现象,甚至可以共生都是后向波的0阶双模.     

Guided modes in asymmetric metal-cladding left-handed material waveguides

We investigate guided modes in the asymmetric waveguide structure with a left-handed material (LHM) layer surrounded by air and metal. A graphical method is proposed to determine the guided modes. New properties of the oscillating and surface guided modes, such as absence of the fundamental mode, coexistence of the oscillating and surface guided modes, fast attenuation of the surface guided modes, and mode degeneracy, are analyzed in detail. We also investigate dispersive characteristics of the metal-LHM- air optical waveguide. The propagation constant increases with decreasing slab thickness for the first-order oscillating mode, which is different from that in traditional metal-cladding waveguides.     

Wave propagation in parallel-plate waveguides filled with nonlinear left-handed material

A theoretical investigation of field components for transverse electric mode in the parallel-plate waveguides has been studied. In this analysis two different types of waveguide structures have been discussed, i.e., (a) normal good/perfect conducting parallel-plate waveguide filled with nonlinear left-handed material and (b) high-temperature-superconducting parallel-plate waveguide filled with nonlinear left-handed material. The dispersion relations of transverse electric mode have also been discussed for these two types of waveguide structures.     

Propagation of p-polarized waves in a linearly graded index film surrounded by negative index materials

The theory of step-index waveguides is well-established. Most practical slab waveguide structures have a graded-index profile. The basic properties of graded-index planar waveguide structures are similar to those of step-index waveguides with subtle differences. The most common types of graded-index slab waveguides are linearly and exponentially graded-index profiles. We here treat linearly graded-index slab waveguide. In this work, a three-layer waveguide structure with linearly graded-index film is considered. We assume three structures: the first structure comprises a left-handed material (LHM) cladding, the second structure contains a LHM substrate layer and the third has a LHM cladding and substrate. Closed-form expressions for electric and magnetic fields and the characteristic equation are derived. The three normalized parameters: the asymmetry coefficient (a), the normalized film thickness (V) and the normalized guide index (b) are used to study the dispersion properties of the proposed slab waveguide structure.     

Coupled mode analysis of light modulation in dielectric waveguides

A detailed analysis of electrooptic light modulation in optical waveguides is presented. Several important problems of a waveguide modulator, such as the difference of waveguide axes from crystalline electrooptic ones, the distribution of transverse and longitudinal field components of light modes, and the traveling-wave property of the modulating field, are discussed. The analysis is based on the coupled mode theory, regarding the modulation as the coupling among sidebands of unperturbed waveguide modes. The coupled mode equation is derived for the modulation in optical waveguides. It can be solved if the normal modes of the waveguide are given. Actually the equation is solved for the modulation in dielectric slab waveguides and the mechanism of modulation is discussed. The results of the analysis are applied to designing two types of waveguide modulators. In an example (10.6 μm modulator with a GaAs slab waveguide) a new efficient crystal orientation is found. The calculated phase retardation with this orientation is 0.13 rad/(V·cm) with a 1 μm thick slab. Another example of a 0.633 μm modulator using a LiTaO₃ crystal as a substrate is also described.     

Research of electromagnetic field in different length left-handed material slab

Finite-difference time-domain （FDTD） method is used to simulate the propagation of electromagnetic wave in left-handed material slab （LHMs） with cold plasma model The effects of optical propagation in the left-handed material compared to convex lens are discussed. The wider the LHMs is, the stronger electric field of focusing image in left-handed material slab is confirmed by the simulation with various slab length. However, the outer image point location would slightly moves to the LHMs side when the length of LHMs is reduced.     

各向异性色散左手材料平面波导的导模特性(英文)

对芯层为左手材料而内外包层都是普通材料的非对称三层平面波导TE振荡模进行了分析.在考虑左手材料色散和各向异性的情况下,从Maxwell方程组出发,得到了TE振荡模的色散方程和功率流分布,并且画出了相应的色散曲线.我们找到了8个TE振荡模,而且包括基模.随着模阶数的增加,模色散曲线右移,功率流曲线下移.但是,随着波导厚度的增加,色散曲线左移,功率流曲线上移.此外,TE振荡模有反常色散特性和负的群速,这正揭示了左手材料的本质特性.     

各向异性色散左手材料平面波导的导模特性

对芯层为左手材料而内外包层都是普通材料的非对称三层平面波导TE振荡模进行了分析.在考虑左手材料色散和各向异性的情况下,从Maxwell方程组出发,得到了TE振荡模的色散方程和功率流分布,并且画出了相应的色散曲线.我们找到了8个TE振荡模,而且包括基模.随着模阶数的增加,模色散曲线右移,功率流曲线下移.但是,随着波导厚度的增加,色散曲线左移,功率流曲线上移.此外,TE振荡模有反常色散特性和负的群速,这正揭示了左手材料的本质特性.