Newly developed highly sensitive LiF:Mg,Cu,Si TL discs with good stability to heat treatment

The preparation method and some dosimetric properties of the new LiF:Mg,Cu,Si discs are presented. The effect of heat treatments on LiF:Mg,Cu,Si was investigated. The shape of the glow curve for LiF:Mg,Cu,Si is similar to that for standard LiF:Mg,Cu,P (GR-200A), and shows minimal differences when annealed in the range from 260 °C to 290 °C for 10 min. The TL sensitivity for LiF:Mg,Cu,Si is much lower than that for GR-200A, but is 35 times larger than that for TLD-100 and is slightly higher than that for HMCP. The height of the high-temperature peaks for LiF:Mg,Cu,Si is not only lower than that for GR-200A, but also lower than that for HMCP. The glow curve shape of LiF:Mg,Cu,Si annealed at 260 °C for different times shows minimal differences and TL response remains stable. These results indicate that the new LiF:Mg,Cu,Si disc has a good stability to thermal treatments and a lower residual TL signal.     

Behaviour of LiF:Mg,Cu,P and LiF:Mg,Ti thermoluminescent detectors for electron doses up to 1 MGy

The behaviour of LiF:Mg,Cu,P and LiF:Mg,Ti detectors at ultra-high doses up to 1 MGy, has been investigated. The presence of the ultra-high-temperature peak (450 °C) of reproducible properties was observed in various batches of LiF:Mg,Cu,P, confirming earlier findings. The results indicate that this peak is not an effect of random impurities nor intrinsic effects of LiF, but it is rather connected with the doping.A parameter called ultra-high temperature ratio (UHTR) was defined in order to quantify the observed changes of LiF:Mg,Cu,P glow-curve shape at very high doses and very high temperatures. The use of this parameter allows to determine an absorbed dose in the range from 1 kGy to 1 MGy. This new method of high-dose dosimetry makes LiF:Mg,Cu,P a unique dosimeter, which is capable to cover at least 12 orders of magnitude of dose range: from a microgray to a megagray.     

Relative efficiency of TL detectors to energetic ion beams

The relative TL efficiency of LiF:Mg, Ti and LiF:Mg, Cu, P was evaluated for several ion beams, ranging from helium to xenon ions. Irradiations were realized at the HIMAC accelerator in Chiba, Japan, partly within the ICCHIBAN intercomparison project. The covered LET range was extending from about 2 keV/μm to 1500 keV/μm.Both tested TLD types exhibited a decrease of relative response with increasing ionization density – stronger for LiF:Mg,Cu,P detectors. The relationship between efficiency and LET was found to follow unique trend lines, as nearly all data points lied within 5% around the fitted empirical functions. Values of TL efficiency measured for various batches of same type TLDs agree within a few percent. The measured relationships between relative TL efficiency and LET will be used in the analysis of data obtained from space dosimetric experiments.     

A study on thermal degradation of LiF:Mg,Cu,P and LiF:Mg,Cu,Si

We investigated the thermal degradation of LiF:Mg,Cu,P (NTL-250) and LiF:Mg,Cu,Si (MCS) for the development of TL sheet. By thermogravimetry and differential scanning calorimetry (TG-DSC), the exothermic reaction was observed between 320 °C and 400 °C in MCS as well as NTL-250. The heat value of MCS was twice as large as that of NTL-250. This ratio corresponded with that of Mg amount in these TL materials measured by ICP-OES (inductively-coupled plasma optical emission spectrometry). X-ray diffraction (XRD) measurements were also carried out, and the peaks of MgF₂ phase were also observed in degraded MCS sample as well as NTL-250. Moreover, X-ray absorption near-edge structures (XANES) of Cu in these LiF TLDs were measured. The valences of Cu did not change before and after degradation. It indicates that the thermal degradation is caused by not Cu but Mg ion state change. The exothermic reaction is possible caused by the stabilization reactions, and then it was expected to correspond with MgF₂ precipitation. From these results, we concluded that the thermal degradations of these LiF TLDs are caused by the precipitation of MgF₂.     

Optimization of preparation procedure of LiF:Mg,Cu,Si TLD for improving the reusability

Several thermal treatments in the temperature range from 270 °C to 320 °C (each of 10 min) were tested as a final preparation procedure of LiF:Mg,Cu,Si to improve the protocol of TL readout with less residual signal for the LiF:Mg,Cu,Si TLD. This high sensitivity LiF:Mg,Cu,Si TLD exhibited thermal stability much better than that of the well known LiF:Mg,Cu,P. For LiF:Mg,Cu,Si, a readout temperature up to 300 °C did not affect the TL sensitivity and glow curve structure for 12 cycles of exposure and readout following an initial thermal treatment at 295 °C for 10 min. The residual TL signal also remained negligible.     

The dependence of thermoluminescence of LiF:Mg,Cu,Si on sintering temperatures and dopants concentrations

The dependence of thermoluminescence (TL) of LiF:Mg,Cu,Si on sintering temperatures and dopants concentrations were investigated. The dependency of the TL in LiF:Mg,Cu,Si on sintering temperature exhibits a very sharp maximum at 830 °C. LiF:Mg,Cu,Si is much too sensitive than LiF:Mg,Cu,P to sintering temperature. The glow curve and the TL sensitivity depend on the concentration of Mg, Cu and Si, showing a distinct maximum for certain concentrations of these impurities. Mg seems to be the most essential dopant, as very small changes of the Mg content strongly influence both the glow curve and the TL sensitivity. Si is the main activator responsible for TL emission. The stability to heat treatments in LiF:Mg,Cu,Si was influenced greatly by Mg concentrations. The thermal instability in LiF:Mg,Cu,Si is caused not by Cu and Si but Mg ion state change. It was found that the optimum concentrations are Mg:0.6 mol%, Cu:0.03 mol% and Si:0.9 mol% for this material, which showed the best stability to heat treatment.     

Influence of sintering temperatures on LiF:Mg,Cu,P with various magnesium concentrations

The dependence of LiF:Mg,Cu,P samples with various concentrations of Mg on sintering temperatures was investigated to find a new dosimeter. The influence of high sintering temperatures on LiF:Mg,Cu,P chips depends strongly on Mg concentrations. The height of the main peak versus the sintering temperatures exhibits a maximum, the position of which varies between 690 °C and 750 °C, depending on the Mg concentration in the range studied. The high temperature peaks of LiF:Mg,Cu,P for various Mg concentrations reduce basically when the sintering temperature is increased. LiF:Mg,Cu,P is much less sensitive than LiF:Mg,Cu,Si to sintering temperature. LiF:Mg,Cu,P with 0.6 mol% of Mg can be re-used at annealing temperature of 260 °C, regardless of the sintering temperature. It was found that the optimum concentration is Mg: 0.6 mol%, the optimum sintering temperature is 750 °C, considering that LiF:Mg,Cu,P with a low residual signal and good sensitivity can be re-used at annealing temperature of 260 °C and produced in a large scale. The new optimum LiF:Mg,Cu,P formation has 52 times higher than that of the TLD-100, and an extremely low residual signal of 0.07% without an initialization readout procedure.     

Investigations of thermoluminescence properties of multicrystalline LiF: Mg,Cu, Si phosphor prepared by edge defined film fed growth technique

Thermoluminescence (TL) properties of LiF: Mg, Cu, Si phosphor prepared in multicrystalline form using edge defined film fed growth (EFG) technique has been investigated. The effect of preparation route on TL properties and thermal stability has been studied. To improve the TL dosimetry properties, phosphor is subjected to different annealing temperatures ranging from 250 °C to 450 °C. The shape of the glow curve structure and peak temperature remains similar at different annealing temperatures, however peak intensities vary. The consistency in the glow curve structure with annealing temperature elucidate that TL trapping states are stable in nature. Thermal annealing at 300 °C for 10 min gives maximum TL intensity with main dosimetry peak at 209 °C. The TL intensity of the main dosimetry peak is increased by a factor of five as compared to as-grown crystal. The thermal stability of LiF: Mg, Cu, Si is found to be better than LiF: Mg, Cu, P. Trapping parameters are calculated to have an insight study of defect states. A simple glow curve structure, tissue equivalency, thermal stability, low residual signal, linear response and reusability makes LiF: Mg, Cu, Si a suitable phosphor for radiation therapy, radio diagnostics and personnel dosimetry applications.     

High-dose characterization of different LiF phosphors

The dose response of three LiF TLDs: standard LiF:Mg,Ti (denoted MTS), high-sensitive LiF:Mg,Cu,P (MCP) and a recently developed in Kraków version of LiF:Mg,Ti with modified activator composition (MTT) and increased high-LET response was measured. The TLDs have been exposed to ⁶⁰Co gamma-rays, up to dose of 10 000 Gy, i.e. beyond saturation dose of the main dosimetric peaks, which corresponds to ca. 1000 Gy. The measured glow-curves were deconvolved into separate peaks with first order kinetic function (using self-developed GlowFit software). The dose response of the main peaks was found to be supralinear for MTS and sublinear for MCP detectors, as expected. The dose response of MTT was found to be even more supralinear than that of MTS. An interesting effect has been observed with regard to glow-curve shape of MCP detectors. Up to a dose of 1 kGy it remains practically unchanged, while for higher doses a strong growth of high-temperature peaks is observed. In the same dose region a decrease of the main peak of MCP with increasing dose is observed, unlike LiF:Mg,Ti detectors.     

Thermally assisted OSL from deep traps in Al2O3:C

The present work suggests an alternative experimental method in order to not only measure the signal of the deep traps in Al₂O₃:C without heating the sample to temperatures greater than 500 °C, but also use this signal for high dose level dosimetry purposes as well. This method consists of photo transfer OSL measurements performed at elevated temperatures using the blue LEDs (470 nm, FWHM 20 nm) housed at commercial Risø TL/OSL systems, after the sample was previously heated up to 500 °C in order to empty its main TL dosimetric trap. The influence of this procedure on specific features such as glow curve shape and sensitivity of the main TL glow peak was also studied.     

Luminescence and evaluation of trapping parameters in NaMgSO4Cl: X (X=Cu or Ce) phosphor

Thermoluminescence (TL) characteristics of recently developed high sensitive mixed halosulphate phosphors, NaMgSO₄Cl: Cu and NaMgSO₄Cl: Ce were studied in comparison with CaSO₄: Dy in order to assess the possibility of their use in personal monitoring and TLD phosphors at very low dose of 5 Gy. It was found that NaMgSO₄Cl: Cu is 5.59 times and NaMgSO₄Cl: Ce is 6.18 times more sensitive as compared to standard CaSO₄: Dy. UV photo-excited luminescence from Cu to Ce doped NaMgSO₄Cl halosulphate phosphors has been investigated. The intense emission of the spectrum is assigned to electronic transitions 3d⁹4s¹→3d¹⁰ in monovalent copper ion and 5d→4f in Ce³⁺ ions. Increase in PL peak intensity suggesting that Cu and Ce play an important role in PL emission in the present matrix. These phosphors were synthesized by the wet chemical method. XRD, photoluminescence (PL) and thermoluminescence (TL) characterization of phosphors has been reported in this paper. The preparation of an inexpensive and high sensitive NaMgSO₄Cl: Cu and NaMgSO₄Cl: Ce with TL glow peaks for different concentrations are observed between 160 and 195 °C and between 200 and 225 °C, respectively, exposed to gamma-rays of ⁶⁰Co for their thermoluminescence (TL) properties. The glow curves have been recorded at a heating rate of 2 K s^?1 and irradiated at a dose rate of 0.995 kGy h^?1 for 5 Gy. In present study the trapping parameters such as order of kinetics (b), activation energy (E) and frequency factors (s) have been calculated for the 195 and 200 °C glow peaks of NaMgSO₄Cl: Cu and NaMgSO₄Cl: Ce, respectively by using Chen's method. The paper discusses the luminescence of Cu⁺ and Ce³⁺ by simple method of incorporation in NaMgSO₄Cl host.     

Further study on the influence of thermal treatments on the glow curve structure in LiF:Mg,Cu,P (GR-200A)

The influence of various annealing treatments with heating temperatures (T_A) from 240 to 700 °C, with re-annealing at 240 °C, and with a combined re-annealing procedure of 20 min at 270 °C followed by 10 min at 240 °C on LiF:Mg,Cu,P (GR-200A) was investigated. As the T_A increased, the intensity decreased rapidly to almost no signal at 340–380 °C then increased clearly and achieved a maximum at 540 °C. The position of the maximum intensity of the glow curve shifted basically in the direction of higher temperatures with an increase at T_A and achieved a maximum of 279 °C when annealed at 460 °C. The re-annealing influenced both the intensity and the glow curve structure at certain degree. The effect of re-annealing on the glow curve depended markedly on the T_A. With re-annealing at 240 °C, the intensity decreased as T_A increased up to 360 °C then increased and achieved a maximum at 540 °C. The intensity could be restored fully when annealed at above 500 °C, however, the glow curve couldn't be restored fully. With a combined annealing, the shape of glow curve of a sample annealed at above 540 °C or below 320 °C was similar to that of the standard glow curve of LiF:Mg,Cu,P and the intensity and glow curve could be restored completely when annealed in the range 620–660 °C. It seems that the main roles of the re-annealing at 240 °C are to restore partially the intensity of peak 4 and peak shape for LiF:Mg,Cu,P when annealed at above 260 °C, and restore fully the total TL intensity of LiF:Mg,Cu,P when annealed at above 500 °C and the main roles of the combined re-annealing are to reduce the intensity of peak 5 and the total TL intensity, increase the intensity of peak 4 and restore the glow curve shape.     

Measurement of the sputter yield after mild ion erosion of a pristine Cu(001) surface

Using the STM technique we have determined the sputter yield on a pristine Cu(001) surface after mild (fluence less than 0.044 ions per surface atom) bombardment of the pristine surface with 800 eV Ar⁺ions at normal incidence. The experiments have been performed at substrate temperatures ranging from 200 to 350 K. Making use of the positional correlation of adatoms and surface vacancies, at 200 K and 325 K, we concluded that about 1/3 of the surface adatoms originate from interstitials arriving at the surface and they give a direct indication of the buried bulk vacancies. A careful analysis of the different areas for surface vacancies and adatom then allowed a quantitative evaluation of the sputter yield at 1.2 Cu atoms per 800 eV Ar⁺ ion.     

Temperature effect on the gamma dose response of glycine (spectrophotometric read-out) system

The glycine (spectrophotometric read-out) dosemeter has a useful dose range of 15–4000 Gy with good reproducibility and post-irradiation stability. It is a potential dosemeter for radiation processing applications, but the dose response of the system may vary with irradiation and measurement temperature. The effect of irradiation and variation in measurement temperature on the gamma dose response of this system was investigated. The gamma dose response was found to be constant for both irradiation and measurement temperatures ranging from 10 to 50 °C, and the maximum variation in response is within ±1%.     

High energy femtosecond OPA pumped by 1030 nm Yb:KGW laser.

We present a traveling-wave-type optical parametric amplifier (OPA) pumped at 1.03 μm by a Yb:KGW laser that produces tunable high-energy pulses of 6.5–4 μJ in the mid-infrared (mid-IR) region from 3.6 to 7 μm. Pumping with negatively chirped pulses generates nearly transform-limited (TL) mid-IR pulses of 300–330 fs length. Pumping with TL pulses of 200 fs not only decreases the output energy by a factor of 1.5, but also decreases the mid-IR pulse-length to 160 fs after additional compression. The compact and simple OPA setup is ideal for femtosecond infrared experiments in the fingerprint region.     

Sonication enhances polyphenolic compounds,sugars, carotenoids and mineral elements of apple juice

A study was initiated with the objective of evaluating the effects of sonication treatment on quality characteristics of apple juice such as polyphenolic compounds (chlorogenic acid, caffeic acid, catechin, epicatechin and phloridzin), sugars (fructose, glucose and sucrose), mineral elements (Na, K, Ca, P, Mg, Cu and Zn), total carotenoids, total anthocyanins, viscosity and electrical conductivity. The fresh apple juice samples were sonicated for 0, 30 and 60 min at 20 °C (frequency 25 kHz and amplitude 70%), respectively. As results, the contents of polyphenolic compounds and sugars significantly increased (P < 0.05) but the increases were more pronounced in juice samples sonicated for 30 min whereas, total carotenoids, mineral elements (Na, K and Ca) and viscosity significantly increased (P < 0.05) in samples treated for 60 min sonication. Losses of some mineral elements (P, Mg and Cu) also occurred. Total anthocyanins, Zn and electrical conductivity did not undergo any change in the sonicated samples. Findings of the present study suggest that sonication technique may be applied to improve phytonutrients present naturally in apple juice.     

Thermoluminescence studies of thermally treated CaB4O7:Dy

Borate based thermoluminescence dosimeters (TLD) show high sensitivity and good TL characteristics. One of the promising material amongst the dosimeters is Dy doped CaB₄O₇. Spectrally resolved thermoluminescence of Dy doped CaB₄O₇ shows three glow peaks at about 50 °C, 240 °C and 380 °C, the intensity of the 240 °C glow peak being the maximum. All TL experiments were conducted on a high sensitivity TL spectrometer at Sussex University with a heating rate of 50 °C min^?1. Two main emissions associated with the Dy dopant are observed at ～480 and 580 nm. The samples were subjected to a series of treatments including excitation by X-rays and UV laser radiation. As part of the present research CaB₄O₇:Dy materials were subjected to two different heat treatments; quenching and slow cooling in order to investigate the changes in TL characteristics.     

Highly efficient and stable organic light-emitting diode by balancing drift current of charge

Highly efficient and stable OLED device in which hole-drift current and electron-drift current are balanced was fabricated. Drift current characteristics according to the thickness of organic layer were examined using the device with ITO/m-MTDATA/NPB/Al structure that can only move the hole and the device with Al/LiF/Alq₃/LiF/Al structure that can only move the electron. Using the result of such examination, green device with balanced drift current was produced. Device with the structure of m-MTDATA (80 nm)/NPB (20 nm)/C-545T (3%) doped Alq₃ (5 nm)/Alq₃ (59 nm)/LiF (1 nm)/Al (200 nm) showed color purity of (0.309, 0.643) and high efficiency of 7.0 lm/W (14.4 cd/A). Most of light emission was observed inside the green emitting layer. Through the result of EL spectrum for the device also including red emitting layer, same result could be obtained. The device with balanced drift current also showed half life-time of 175 h for initial luminance of 3000 cd/m², which is more stable in comparison to the device without balanced drift current.     

Segments of a commercial Ge-doped optical fiber as a thermoluminescent dosimeter in radiotherapy

Optical fibers have been proposed as dosimeters in both diagnostic and radiotherapy applications. A commercial germanium (Ge)-doped silica fiber with a 50 μm core diameter which showed good thermoluminescence (TL) properties was selected for this study. The radiation sources used were a high dose rate brachytherapy iridium-192, MV photon and MeV electron beams from a linear accelerator. The coating of the fiber was chemically removed and then annealed at 400 °C for 1 h prior to irradiation. After irradiation, the fiber was read on a Harshaw Model 3500 TLD reader. The optical fiber had one well-defined glow peak at 327 ± 2 °C at all the radiotherapy energies. The dose response was linear within the clinical relevant dose for all these energies. Reproducibility was mainly within 4–6% (one standard deviation) for high energy photons and electrons. The fiber was found to be energy independent within the MV photon energy range. At room temperature the fading up until 1 month was around 6% which was within the 6% uncertainty of the sensitivity calibration of the fiber. Re-using the fiber four times did not significantly alter the sensitivity factor. The optical fiber was found to be dose rate as well as angular independent. Central axis depth dose curves of both 10 MV photons and 12 MeV electrons using the fiber showed relatively good agreement to standard depth dose curves in water within 4%. The Ge-doped fiber is a promising TL dosimeter but improvements have to be made to reduce the reproducibility within 3% for high energy photons and electrons.