O2/CO2气氛下循环流化床煤燃烧SO2排放

在热输入功率50 kW的循环流化床O₂/CO₂燃烧试验装置上研究燃煤SO₂排放特性及石灰石脱硫机理。结果发现,未添加石灰石时,O₂/CO₂气氛下SO₂排放量比相同O₂浓度的空气气氛下低;随着O₂浓度的升高,排放量升高。相同钙硫摩尔比下,O₂/CO₂气氛下石灰石的脱硫机理以直接脱硫为主,脱硫效率比空气气氛下高;随着O₂浓度的增加,石灰石脱硫效率提高。     

低温等离子体分解N2/O2/NO气氛中NO试验研究

利用自行设计的介质阻挡放电型低温等离子体反应器,研究了NO初始浓度、O₂初始浓度、放电功率、电源频率等因素对NTP转化N₂/O₂/NO气氛中NO的影响规律。研究发现,NO去除率随功率增大而升高,到达一最大值后随功率增大而降低;NO去除率随O₂初始浓度增加而降低,随NO初始浓度增大而减小。相同放电功率下,同一组分中NO去除率随电源频率的增加而降低,因此相同放电功率下降低电源频率可提高NO去除率。O₂初始浓度不高于5%时,NO_x大部分为NO,NO₂和O₃浓度均随放电功率增大而降低,NO₂、O₃生成量随O₂初始浓度升高而增多。     

滑动弧裂解CO2机理

建立了一维滑动弧裂解CO₂的反应机理模型. 利用对流冷却的特征频率计算横向气流对流引起的等离子体组分损失. 将等离子体密度和温度的数值模拟结果与文献中滑动电弧等离子体反应器的实验数据进行了对比,吻合较好. 模拟结果表明,滑动弧裂解CO₂会产生大量O和O₂等活性助燃粒子以及可燃的CO. 随着对流冷却特征频率的增加,放电过程中最大电子数密度和电子温度减小,CO₂转化率下降. 在整个CO₂裂解机制中e+CO₂→e+CO+O的贡献最大,准稳态中贡献率为90.63%,瞬态中贡献率为98.43%. 反应CO+O+M→CO₂+M对CO₂生成的贡献率最大. 在实际应用中,为提高CO₂转化率,可以通过增大放电电流,增大e+CO₂→e+CO+O的反应速率,同时选择合适的气体流量,避免过大的速度引起CO₂转化率下降.      

Pu(100)表面吸附CO2的密度泛函研究

采用广义梯度密度泛函理论的改进Perdew-Burke-Ernzerh方法结合周期性层晶模型,研究了CO₂分子在Pu（100）面上的吸附和解离.吸附能和几何构型的计算表明,CO₂以穴位C4O4构型吸附最为有利,吸附能为1.48 eV.布居分析和态密度分析表明,CO₂与Pu表面相互作用的本质主要是CO₂分子的杂化轨道2π_μ与Pu5f,Pu6d,Pu7s轨道通过强电子转移和弱重叠杂化的方式相互作用而生成了新的化学键.计算的CO₂→CO+O解离能垒为0.66 eV,解离吸附能为2.65 eV, 表明在一定热激活条件下CO₂分子倾向于发生解离性吸附.O₂,H₂,CO和CO₂在Pu （100）面吸附的比较分析表明,较低温度下的吸附强度顺序依次为O₂,CO,CO₂,H₂;较高温度下的吸附强度顺序依次为O₂,CO₂,CO,H₂. 关键词： 密度泛函理论 Pu （100） 2')" href="#">CO₂ 吸附和解离     

Cu掺杂纳米TiO2光催化还原CO2实验研究

利用溶胶凝胶法制备不同掺杂量的CuO-TiO₂纳米粉体,采用热重差热分析仪（TG-DTA）,X射线衍射仪（XRD）,场发射扫描电镜（FSEM-EDX）等手段对其进行表征;在波长为253.7nm的紫外灯照射下,进行CO₂光催化还原实验研究,探究CO₂光催化资源化利用可行性,。结果表明,溶胶凝胶法制备所得CuO掺杂TiO₂纳米粉体,粒径大小在20～30 nm之间;CO₂光催化还原主要产物为甲醇,掺杂量为5%（质量分数）CnO-TiO₂纳米粉体催化效果最好,反应10 h后得到甲醇产量为27mg·（g-cata）^-1;随着反应时间的增加,产物中甲醇含量也逐渐增加。     

载体结构对固态胺吸收CO2性能的影响

利用六种孔结构不同的商业无定形硅胶制备了不同四乙烯五胺（TEPA）担载量的固态胺吸收剂。吸收剂的微观结构通过BET和SEM测试;并在TGA反应器中,考察固态胺在30～80℃,CO2体积分数为1%～100%范围内的吸收性能。实验表明,固态胺吸收CO₂性能与温度、CO₂浓度以及载体结构有密切的联系。固态胺适合在低温（30～60℃）低CO₂浓度下（约10%）进行CO₂分离。载体结构通过影响最优担载量,从而影响固态胺吸收性能,孔容和孔径分别在1.211 cm³/g和13 nm附近的载体在担载量为45%时拥有最好的吸收能力（2.87 mmol/g）。     

采用详细化学反应机理研究煤富氧燃烧NO_x生成机制

本文采用详细化学反应机理,建立氧煤燃烧气固反应模型,分析煤在富氧燃烧条件下NO_x生成机制,研究不同O₂浓度和分级燃烧对NO_x排放的影响。富氧燃烧时,NO_x生成主要路径为:HCN→CN→NCO→NO和HCN→CN→NCO→HNCO→HN₂→NH→HNO→NO。初始O₂增大,挥发分和HCN析出时间提前,高的O₂初始浓度对燃料N转化率有促进作用;煤富氧分级燃烧时,主燃区还原气氛有利于NO还原为N₂,其主要还原路径如下:NO+CO→N+CO₂、NO+H→N+OH和NO+N→N₂+O,当主燃区过量空气系数SR₁从1.15减小到0.6,N最终转化率（t=1000 ms）只是从0.379减小到0.339,相对于未分级燃烧时变化了10.55%,与煤空气分级燃烧相比,煤富氧分级燃烧对N转化率影响较小。     

V2CO2MXene从CO2/N2混合气体中选择性吸附CO2的第一性原理计算

二氧化碳作为温室气体中最重要的组成部分,其含量的变化将直接影响全球气候变化,在燃烧后气体中选择性捕获CO₂,对减缓因CO₂浓度过高引发的环境问题具有十分重要的意义.本文采用第一性原理计算的方法,研究了V₂CO₂ MXene材料对CO₂的选择性吸附性能.首先研究了不同官能团V₂CT_X MXene材料的结构和性质,发现V₂CO₂具有良好的稳定性.后研究了V₂CO₂对CO₂的吸附行为,结果表明,当CO₂被水平吸附时,V₂CO₂对CO₂气体分子的吸附能力较强且均满足在高性能吸附剂表面吸附CO₂的理想值(-0.42 eV-0.82 eV),可以适用于探测/捕获CO₂气体分子.此外,进一步研究了相同条件下V<...     

电场作用下S修饰C24N24从CO2/N2混合气体中选择性吸附CO2的第一性原理计算

在燃烧后气体中选择性捕获CO₂,对减缓因CO₂浓度过高引发的环境问题具有十分重要的意义.本文采用第一性原理计算的方法,研究了外加电场作用下S修饰C₂₄N₂₄富勒烯(S@C₂₄N₂₄)对CO₂的选择性吸附性能.首先研究了S@C₂₄N₂₄的结构和性质,发现其具有良好的稳定性.其次,研究了无电场时S@C₂₄N₂₄对CO₂的吸附行为,发现其吸附为弱的物理吸附.另外,进一步研究了外加电场作用下S@C₂₄N₂₄对CO₂的吸附行为.结果表明,结合距离(CO₂与S)和CO₂的键角(O=C=O)随电场的增大而减小;当电场增加到0.018 a.u.时,物理吸附转变为化学吸附.关闭电场时,化学吸附又转化为物理吸附.此外,即使在相同的电场条件...     

植物叶绿素荧光对CO2反演精度的影响

大气散射效应作为CO₂反演的主要误差源,严重影响了大气CO₂卫星测量的反演精度。氧气在大气中含量稳定,大气CO₂反演方法中常利用氧气的这一特性进行散射校正,其中典型的有光子概率密度函数(PPDF)方法。然而,O₂ A吸收带的光辐射中存在的植物叶绿素荧光会在不同程度上影响PPDF因子的反演,进而限制了CO₂反演精度。由于植被荧光信号较弱,在以往CO₂反演中没有引起足够重视。在调研全球植被荧光分布的基础上,模拟分析了荧光对大气CO₂柱含量(XCO₂)的影响。模拟计算无气溶胶条件下,以及气溶胶和地表反照率两者综合条件下荧光的影响,结果显示,当不考虑气溶胶的影响,荧光强度从0.1增加到1.8(mW·m-2·sr-1·nm-1),会给CO₂的反演结果造成0.1~2 (10-6)的偏差;考虑气溶胶与地表反射率的影响时,会给CO₂的反演结果造成(0.1~3)×10-6的偏差。此研究表明,对于具有高精度需求的CO₂反演,植物叶绿素荧光是一个不可忽略的影响因素。     

Absorption coefficients of O3 at CO2 laser wavelengths

The O₃ absorption coefficients for the rotational lines P(12)–P(28) of the 9.4 μm emission band of the CO₂ laser are presented. Measurements were made in O₃–air dilute mixtures (20–600 ppm) at 25°C and a total pressure of 1013.25 h Pa using a frequency stabilized cw CO₂ laser and values have been determined with greater precision than in previously reported studies.     

Solid-state electrochemical CO2 sensor by coupling lithium ion conductor (Li2CO3-Li3PO4-Asl2O3) with oxide ion-electron mixed conductor (La0.9Sr0.1MnO3)

A solid-state electrochemical cell of the type O₂(air), PtLa_0.9Sr_0.1MnO₃/Li₂CO₃(+5 mol% Li₃PO₄ + 6 mol% Al₂O₃)/Au, CO₂, O₂ was composed to determine CO₂ concentration, where Li₂CO₃, a lithium ion conductor, was used as an electrolyte, and the perovskite-type oxide (La_0.9Sr_0.1MnO₃)/O₂-electrode as a reference electrode. The electromotive force (EMF) of the cell was found to be proportional to the logarithm of CO/₂ partial pressure in CO₂/O₂/N₂ gas mixtures at temperatures between 300 and 400 °C. The EMF responded to changes of CO₂ partial pressure within 1 min at 400 °C. The sensitivity to CO₂ of this cell was not affected by coexistence of O₂, and the EMF remained constant after the first 15 days. The mechanism for sensing CO₂ is discussed.     

The stability of SiC coating and SiO2/SiC multilayer on the surface of graphite for HTGRs at normal service condition

The stability of SiC coating in helium with a low concentration of O₂, CO₂, and H₂O is a key factor for their application in improvement of oxidation resistance of graphite for high temperature gas-cooled reactors (HTGRs). Through thermodynamic analysis, it is found that the influence factor controlling the critical temperature of passive oxidation for SiC is partial pressure of active gas in helium; the critical temperature of passive oxidation for SiC increases with the partial pressure of O₂, CO₂, and H₂O, SiC is prone to undergo active oxidation in He–CO₂ and He–H₂O system. SiO₂/SiC multilayer coating can improve the oxidation resistance of graphite at higher temperature than SiC coating does under normal operation condition for HTGRs.     

稀释剂对H2/CH4预混火焰熄灭特性影响

掺氢天然气在稀释气体作用下的熄灭特性研究对实际燃烧设备的设计和优化具有重要的指导意义。本文利用对冲火焰法测量了掺氢天然气层流火焰在N₂和CO₂作用下的熄灭拉伸率,并采用数值模拟耦合详细化学反应机理对N₂,CO₂和He的稀释剂效应展开研究。结果表明,Li、GRI Mech 3.0和FFCM-1机理均能定性反映燃料熄灭拉伸率随当量比的变化规律,且FFCM-1机理综合预测精度最高。实验和模拟发现,不同稀释剂气体对掺氢天然气熄灭拉伸率降低幅度满足:He22。进一步研究发现,CO₂由于热容大,在反应体系中会降低火焰温度,同时增强了链终止反应强度,通过热效应和化学效应两方面对火焰熄灭特性起作用。He则能显著改变燃料混合物的平均摩尔质量,从而改变体系中重要反应物和自由基的扩散特性,从扩散效应方面影响火焰的熄灭特性。     

高压下CO2稀释的CO/H2/Air火焰贫可燃极限处的辐射重吸收效应的数值研究

本文分别采用考虑辐射重吸收的谱带辐射（SNBCK）模型及未考虑辐射重吸收的光学薄辐射（OPT）模型,对0.1～4 MPa,CO₂稀释比为0%和20%的一维预混层流合成气/空气火焰进行数值分析,研究辐射重吸收效应对可燃极限及极限处的火焰传播速度和温度的影响。结果表明,辐射重吸收效应能有效拓宽贫可燃极限,提高燃料中CO₂比例或提高CO/H₂比例都会加剧上述效果。辐射重吸收效应随压力增大而逐渐增强,并造成可燃极限处最大火焰温度随压力先增加后减小,在1 MPa左右达到峰值。     

Electrical conductivity and defect structure of Mg-doped Cr2O3

The electrical conductivity of Cr₂O₃ nominally doped with 2 mol% MgO has been studied by the four point a.c. technique as a function of the oxygen activity (O₂ + Ar, CO + CO₂ and H₂ + H₂O) in the temperature range 400–1200 °C. It is concluded that Cr₂O₃ doped with MgO is an extrinsic conductor and that the dissolved Mg-dopant is compensated by the formation of electron holes at near atmospheric oxygen pressures and by oxygen vacancies (or possibly interstitial chromium ions) at highly reduced oxygen activities (in CO + CO₂ and H₂ + H₂O gas mixtures). In H₂ + H₂O mixtures Mg-doped chromia also dissolves hydrogen as protons and significantly affects the defect structure and electrical conductivity. The defect structure of the oxide under various conditions is discussed.     

Pseudo-copper Ni–Zn alloy catalysts for carbon dioxide reduction to C2 products

Electrocatalytic CO₂ reduction reaction (CO2RR) to obtain C₂ products has drawn widespread attentions. Copper-based materials are the most reported catalysts for CO₂ reduction to C₂ products. Design of high-efficiency pseudo-copper catalysts according to the key characteristics of copper (Cu) is an important strategy to understand the reaction mechanism of C₂ products. In this work, density function theory (DFT) calculations are used to predict nickel–zinc (NiZn) alloy catalysts with the criteria similar structure and intermediate adsorption property to Cu catalyst. The calculated tops of 3d states of NiZn3(001) catalysts are the same as Cu(100), which is the key parameter affecting the adsorption of intermediate products. As a result, NiZn3(001) exhibits similar adsorption properties with Cu(100) on the crucial intermediates *CO₂, *CO and *H. Moreover, we further studied CO formation, CO hydrogenation and C–C coupling process on Ni–Zn alloys. The free energy profile of C₂ products formation shows that the energy barrier of C₂ products formation on NiZn3(001) is even lower than Cu(100). These results indicate that NiZn3 alloy as pseudo-copper catalyst can exhibit a higher catalytic activity and selectivity of C₂ products during CO₂RR. This work proposes a feasible pseudo-copper catalyst and provides guidance to design high-efficiency catalysts for CO₂RR to C₂ or multi-carbon products.