随钻声波测井隔声体刻槽影响的数值模拟研究*

针对随钻声波测井中钻铤波干扰以及刻槽后散射波问题，该文 利用时域有限差分法模拟钻铤波在随钻隔声体中的传播规律，首先考察在无限大流体中钻铤波在凹槽分界面处的散射特征，利用波场快照直观显示了钻铤波会有一部分能量在刻槽的固液界面转化为斯通利波。同时在有地层时分别对比了均匀内刻槽和外刻槽对钻铤波的衰减效果，发现在选择均匀内刻槽还是外刻槽时结果不仅与频率范围有关，而且与刻槽的深度也有关系。最后对比了槽宽较大的均匀凹槽隔声体和槽宽较小的渐变凹槽隔声体。可以得出结论，在设计随钻隔声体时，在10 kHz以下选择均匀外刻槽方式相对于内刻槽隔声效果会更好。随着刻槽槽深增加，外刻槽在10 kHz以下相比于内刻槽隔声性能优势更加明显。渐变刻槽在满足衰减钻铤波幅度要求的同时，散射波对后续地层波和斯通利波影响也更小。     

周期性非轴对称孔槽结构隔声性能数值模拟研究

设计了一种利用周期性非轴对称孔槽来消除钻铤模式波的隔声体结构,并采用三维有限元法对其隔声效果进行了数值模拟。结果表明:所提出的隔声体的隔声效果与孔槽圆弧的半径、孔槽间隔及孔槽的数目等有关;适当选取刻槽方式时,1 m长的隔声体对单极子源激发的钻铤波的衰减可达22 dB,但对偶极子源激发的挠曲波的衰减效果不明显。     

偶极随钻声波测井声压和径向位移响应的差异*

声波测井仪接收到的电信号通常是多个压电片响应的叠加,它主要是由声压还是径向位移响应转化而来,或是两种响应兼有目前未有定论。该文通过实轴积分法和复变函数法计算并对比分析随钻声波测井的声压和径向位移场,发现这两种响应特性有着显著的差异。首先,软地层的偶极随钻测井时,声压信号包含钻铤波和舒尔特波两个波群,而径向位移信号仅有钻铤波波群;其次,单极声源情况下,声压和径向位移信号的钻铤波能量分别集中在钻铤内、外壁,而偶极情况恰好相反,可见,钻铤按照单极情况的分析结果进行刻槽后,高频时的拖尾现象会影响偶极信号中舒尔特波对横波速度的反演。因此,阐明两类信号的差异对横波速度的反演和钻铤波的压制都具有重要意义。     

基于Hilbert变换的水下多源声信号频率的相干探测

为实现水下中低频声信号的探测识别,通过研究水下多声源相干探测信号的特征,理论上给出了相干探测信号频谱混叠情况下的特征表达式,并提出了一种基于Hilbert变换的信号解调处理方法,实现了水下多声源相干探测信号频谱混叠情况下各声源发声频率的解调.该方法将探测信号经过滤波平滑处理之后进行Hilbert变换,得到信号的解析形式,然后对解析信号模值的平方进行二次滤波平滑等处理,分离混叠在一起的频带,将得到的信号进行频谱分析,根据频移值计算得到水下各个声源的发声频率.在光学暗室下搭建激光相干探测系统,对2~6kHz的水下声信号进行实验,实验结果表明,该方法可以有效分离探测信号中混叠在一起的信号频带,并准确提取各水下声信号的发声频率,频率提取重复性不大于2.5Hz.     

单极随钻声波测井换能器感知信号类型的研究

在假定钻铤是光滑的提前下，前人理论模拟了随钻测井的声压波形，但未发表关于理论波形与实验波形的比较的文章。为了认识测量信号所对应的力学类型及相应类型的钻铤波在钻铤内的分布，本文将理论模拟的随钻声波测井波形与实验波形进行对比。与前人单独考虑压电效应或井孔传播效应不同，本文模拟单极随钻声波测井响应时，将发射器、接收器、光滑钻铤和井孔结构作为一个整体，采用有限元法计算模拟了电压源激励下接收器纪录的声压信号和位移信号。将模拟的声压波形与电压信号进行比较，发现二者的钻铤波与斯通利波相对幅值相差较大，而模拟的径向位移波形更接近电压信号。进一步比较理论波形与小模型井内实验测量到的电压信号，证实电压信号更接近位移信号而与声压信号差异明显。这表明当钻铤光滑时，单极随钻声波测井换能器感知的主要是径向位移信号。研究还表明声压信号中的钻铤波能量主要集中在钻铤内壁，径向位移信号中的钻铤波能量主要集中在钻铤外壁。     

基于混沌激光干涉的分布式光纤声音传感

提出了一种基于混沌激光干涉的分布式光纤声音传感系统,利用外腔反馈式半导体混沌激光作为传感光源,借助非等长的马赫-曾德尔双臂引入干涉光程差,通过直线型Sagnac结构克服了环形干涉系统的互易效应,利用频谱的零频点实现了声音信号的分布式定位。实验结果表明,该系统可实时提取1kHz的单音信号及200~900Hz频率范围内的语音信号。与传统的宽带放大自发辐射激光相比,基于混沌激光干涉的传感系统具有更好的声音频响曲线、更高的检测灵敏度以及均匀的平面指向性,并在12km长的单模光纤上实现了宽谱声音定位,为分布式光纤声音传感系统提供了一种新的灵敏度提升方案。     

多分量横波远探测成像测井仪研制及应用*

该文成功研制出一种新型的胜利多分量横波远探测成像测井仪。该仪器采用低频偶极声源设计,低频高效隔声体、高保真大数据快速传输技术,实现高信噪比多分量反射横波信号的采集,从而可以对井外远距离、不同走向的地质异常体进行探测;并结合专用成像处理软件,可以较好压制低频斯通利波反射,有效提取弱的反射横波信号,最终实现了远程偶极反射横波成像。该测井仪器理论上可以对井外320 m范围内地质异常体进行探测,在刻度井的测试中清晰探测到80 m内的地质异常体,实际测井中已成功获得井外100 m范围内的成像结果。     

小波尺度相关滤波及其改进算法在电火花声源信号处理中的应用

分析提取宽带电火花声源信号,受到船舶辐射噪声的严重干扰,在5 kHz以下的能量集中区信噪比低,且二者Lipschitz指数特性相近,传统基于相邻尺度相关的滤波算法抗干扰能力有限。根据宽带电火花声源信号不同频带所受干扰的不同,信噪比较高的小尺度高频小波系数,采用相邻尺度相关的滤波算法;信噪比较低的大尺度中低频小波系数,采用跨尺度相关的滤波算法,并对算法中阈值系数的选取方法进行修正。结果表明,该算法滤波效果良好,有效的提取了电火花声源信号,适合窄带强干扰背景噪声下的宽带水声信号处理。      

弹性波数值模拟系统

弹性波数值模拟是石油测井仪器设计、研发和制造的有效工具,其有助于优化仪器的换能器频率、发射与接收器间的源距、接收器的个数及间距、隔声体的结构,也可帮助理解特定声源在复杂环境中的声传播规律及正确认识和评     

四边简支含多孔材料双层板隔声特性

有限大含多孔材料和空气层复合板结构隔声特性的研究尚不充分。该文旨在研究四边简支边界条件下复合板结构隔声特性。首先基于流体饱和多孔弹性介质的声传播理论计算了声波在多孔介质中的传播波数；继而采用四边简支边界条件下板结构的模态函数，利用模态叠加法和伽辽金法推导了复合板结构隔声系数理论模型，并数值求解复合板隔声量。将理论模型得到的四边简支复合板隔声量与实验结果对比，验证了理论模型的正确性。最后，详细讨论了边界条件、板结构尺寸和多孔材料厚度等主要参数对隔声特性的影响。结果表明：四边简支复合结构隔声特性曲线上“谷值”出现得较少，并且简支复合板隔声特性的第一个“吻合频率”比固支支撑复合板更靠近低频，当频率超过3000 Hz以后，简支和固支边界条件复合板结构隔声特性趋于一致。     

Evaluating airborne sound insulation in terms of speech intelligibility

This paper reports on an evaluation of ratings of the sound insulation of simulated walls in terms of the intelligibility of speech transmitted through the walls. Subjects listened to speech modified to simulate transmission through 20 different walls with a wide range of sound insulation ratings, with constant ambient noise. The subjects' mean speech intelligibility scores were compared with various physical measures to test the success of the measures as sound insulation ratings. The standard Sound Transmission Class (STC) and Weighted Sound Reduction Index ratings were only moderately successful predictors of intelligibility scores, and eliminating the 8 dB rule from STC led to very modest improvements. Various previously established speech intelligibility measures (e.g., Articulation Index or Speech Intelligibility Index) and measures derived from them, such as the Articulation Class, were all relatively strongly related to speech intelligibility scores. In general, measures that involved arithmetic averages or summations of decibel values over frequency bands important for speech were most strongly related to intelligibility scores. The two most accurate predictors of the intelligibility of transmitted speech were an arithmetic average transmission loss over the frequencies from 200 to 2.5 kHz and the addition of a new spectrum weighting term to R(w) that included frequencies from 400 to 2.5 kHz.     

Generalized collar waves in acoustic logging while drilling

Tool waves, also named collar waves, propagating along the drill collars in acoustic logging while drilling(ALWD),strongly interfere with the needed P- and S-waves of a penetrated formation, which is a key issue in picking up formation P- and S-wave velocities. Previous studies on physical insulation for the collar waves designed on the collar between the source and the receiver sections did not bring to a satisfactory solution. In this paper, we investigate the propagation features of collar waves in different models. It is confirmed that there exists an indirect collar wave in the synthetic full waves due to the coupling between the drill collar and the borehole, even there is a perfect isolator between the source and the receiver.The direct collar waves propagating all along the tool and the indirect ones produced by echoes from the borehole wall are summarized as the generalized collar waves. Further analyses show that the indirect collar waves could be relatively strong in the full wave data. This is why the collar waves cannot be eliminated with satisfactory effect in many cases by designing the physical isolators carved on the tool.     

Measurement of sound insulation with a sound level meter

The present technique for measuring the airborne sound insulation of walls and floors, involving measurements in 16 one-third octave bands, is tedious and expensive. The method provides more information than is needed for most purposes, and is more suited to research.Several investigators have proposed the measurement of the overall A-weighted sound level difference using a sound level meter, with a broad band source of white or pink noise. Consistent results have been obtained but their relation to accepted rating methods such as STC is rather empirical.The reference curves used for airborne sound insulation, i.e. STC and HPGW are very similar to the A weighting curve, and if the latter were adopted as the reference curve, there would be a firm theoretical basis for measurement with a sound level meter. Measurement of the difference between the linear sound level of a source of white noise, and the A weighted received level, would in practice be a test of the conformity to the A weighting curve of the transmission loss curve of the partition. Adverse deviations would show as a higher received level. Favourable deviations would have little effect.A study of practical walls and floors, taken from National Building Studies Research Paper 33, showed that there was good correlation between the sound level difference calculated as if it had been measured directly with a sound level meter, and a proposed rating method similar to ISO R717, but using the A weighting curve as the reference curve. Ninety-six per cent of results were within ±1 dB.The practical difficulties of achieving a reasonably flat transmitted spectrum, and of correcting for room absorption will reduce this precision, but bearing in mind the practical success of other short tests, the proposed test should provide a rapid test which is adequate for approval purposes.     

Utilizing vector hydrophones to achieve an active anechoic terminal in an acoustic tube

A new integrated active sound absorptive terminal using vector hydrophones is developed for the anechoic terminal of impedance tube,with which the reflected and the incident waves can be separated.The method overcomes the limitations imposed by the sensor spacing and measuring frequency range in the traditional two-hydrophone method,and can effectively expand low-frequency sound absorption band of the terminal.The effect of hydrophone sensitivity on the sound absorptive performance of the terminal is evaluated,a correction method is also provided for the reflection and transmission coefficient.The experimental results show that the absorption coefficient in the frequency band of 0.1-2 kHz is over 0.98,which agrees well with the theoretical results.     

Acoustic Pulse Diffraction by a Sphere in a Planar Layered Waveguide with a Gradient Layer

Consideration of the vertical sound velocity profile is highly important for solving problems of sound propagation in waveguides and scattering problems. A pulsed echo signal reflected from a spherical scatterer in a waveguide is modeled for the case of a waveguide characterized by sound velocity increasing with depth. The simplest model of the medium is considered in which the scatterer, the source, and the receiver are positioned in a layer with constant sound velocity. Below this layer, the sound velocity increases with depth so that the square of refractive index varies according to linear law. The scattering coefficients for the sphere are calculated using the normal wave method. The number of normal waves forming the echo signal is determined by the preset directionality of the source. Modeling is performed in a frequency band of 70?90 kHz for distances between the scatterer and the transmitter-receiver within 500?1000 m. The transmitted signal has the form of a pulse with cosine envelope and central frequency of 80 kHz.     

高频宽带嵌套式复合材料换能器*

研制了一种嵌套式高频宽带复合材料换能器,利用1-3型压电复合材料Q值较低、频带较宽的特点,采用组合式的结构拓展换能器的工作带宽。通过切割框型压电陶瓷、灌注环氧树脂得到压电复合材料框型敏感元件,再将不同厚度的框型敏感元件沿轴向嵌套从而制成多层嵌套的压电复合材料敏感元件。建立1-3型压电复合材料中压电小柱的等效电路,根据等效电路计算出压电小柱的谐振频率,并与1-3型压电复合材料的谐振频率理论计算结果进行对比。通过ANSYS软件对敏感元件结构进行仿真,并根据仿真结果确定了敏感元件的最佳设计方案。最终制作出的换能器进行水下测试,该换能器的谐振频率为310kHz,最大发送电压响应为188.5dB,-3dB带宽可达130kHz,接收灵敏度最大可达-186.8dB,-3dB带宽可达90kHz,谐振频率处-3dB的指向性开角约为2.4°。该嵌套式敏感元件可实现换能器宽带发射与接收声波的目标。     

水下隔声结构设计及评价方法

为使用混响法快捷地测量水下结构物的辐射噪声,需基于港口或海岸建造海上混响水池。针对内外都是水情况下的海上混响水池壁面隔声问题,设计了一种带梁空气夹层板水下隔声结构,通过仿真比较了不同参数的空气夹层板的隔声性能。为评价声波无规入射情况下水下大尺寸隔声结构隔声性能,提出了一种混响评价方法,通过隔声实验比较了混响法与脉冲法的不同。结果表明：带梁空气夹层板的水下隔声性能优异,声波无规入射情况下,面板厚度0.015 m、空气层厚度0.020 m的带梁空气夹层板在2～10 kHz频段插入损失大于20 dB;混响法可以有效评价大尺寸水下隔声结构的平均隔声性能,其反映的声波无规入射的平均隔声性能更接近于实际应用情况。     

薄膜型声学超材料的结构设计与隔声特性*

为探讨薄膜型声学超材料用于汽车前围声学包、提高其中低频隔声能力的可行性,设计一种米字摆臂多质量块薄膜型声学超材料,构建其隔声分析有限元模型 ,分析其隔声特性及影响因素,开展结构优化及其在汽车前围声学包上的应用探索。研究表明,所设计的薄膜型声学超材料单胞在中低频区域具有较宽的隔声频带;增加薄膜上质量块半径或厚度会使传声损失曲线整体向低频区域移动,且质量块半径的增加还会拓宽高频区域的隔声频带;增加薄膜厚度或预应力会使传声损失曲线整体向高频区域移动;优化后的薄膜型声学超材料与钢板组合应用于汽车前围板,可明显提高其中低频隔声能力。     

周期性轴对称凹槽结构隔声特性数值模拟

提出一种在钻铤上切割周期性轴对称凹槽方式构建隔声体,消除钻铤模式波的方法.结果表明,其隔声效果与凹槽深度H、长度L、凹槽数目N、凹槽截面形状以及钻铤壁厚有关.选择矩形截面凹槽、减小钻铤壁厚、增加凹槽深度都可有效提高隔声体的隔声效果,该结构最高可获得约36 dB的声衰减,基本满足随钻声波测井仪器对隔声效果要求.