An investigation of the crystallization kinetics of zeotype SAPO-34 crystals synthesized by hydrothermal and sonochemical methods

The kinetics study of SAPO-34 crystallization from a gel containing morpholine as a structure directing agent (SDA) was investigated by means of X-ray diffraction (XRD) patterns in order to determine the kinetics parameters, i.e. induction times, rate constants, frequency factors, and activation energies for the induction and growth stages. The kinetics data of growth period were determined by using the Avrami–Erofeev nucleation growth model. SAPO-34 molecular sieves were synthesized by using both sonochemical-assisted hydrothermal and conventional hydrothermal heating at temperatures of 180, 200, and 220 °C to elucidate the influence of crystallization method on the crystallization kinetics of SAPO-34. The activation energy values indicated that the crystal growth mechanism was enhanced for samples synthesized sonochemically, whereas the induction energy was not greatly affected by using sonication process. Also, the kinetic compensation effect (KCE) was considered in order to obtain the isokinetic temperature.     

Synthesis of NaP zeolite at room temperature and short crystallization time by sonochemical method

NaP zeolite nano crystals were synthesized by sonochemical method at room temperature with crystallization time of 3 h. For comparison, to insure the effect of sonochemical method, the hydrothermal method at conventional synthesis condition, with same initial sol composition was studied. NaP zeolites are directly formed by ultrasonic treatment without the application of autogenous pressure and also hydrothermal treatment. The effect of ultrasonic energy and irradiation time showed that with increasing sonication energy, the crystallinity of the powders decreased but phase purity remain unchanged. The synthesized powders were characterized by XRD, IR, DTA TGA, FESEM, and TEM analysis. FESEM images revealed that 50 nm zeolite crystals were formed at room temperature by using sonochemical method. However, agglomerated particles having cactus/cabbage like structure was obtained by sonochemical method followed by hydrothermal treatment. In sonochemical process, formation of cavitation and the collapsing of bubbles produced huge energy which is sufficient for crystallization of zeolite compared to that supplied by hydrothermal process for conventional synthesis. With increasing irradiation energy and time, the crystallinity of the synthesized zeolite samples increased slightly.     

Microstructural study of different LDH morphologies obtained via different synthesis routes

In order to better understand the relationship between LDH synthesis parameters and their particle sizes, diverse carbonate intercalated NiAl-LDH phases were prepared using different coprecipitation conditions and their structure, microstructure and morphology were characterized. The samples were synthesized by coprecipitation either at constant pH, in strong alkaline medium or using urea decomposition. The influence of a post-synthesis hydrothermal treatment was also investigated. A well crystalline NiAl-CO₃ phase but containing a high stacking fault density was obtained by combining a strong basic medium and hydrothermal treatment at 120 °C for 24 h. Interestingly, the hydrothermal treatment increases the crystallinity of the samples but does not eliminate stacking faults. The crystallite sizes determined by modeling X-ray diffraction peak broadening with linear combinations of spherical harmonics are fully consistent with TEM observations confirming the validity of the approach used and indicating that the particles are probably small single crystals.     

Synthesis and optical properties of 10 mol% Ce, 5 mol% Tb co-doped KGdF4 and GdF3 submicro/nanocrystals

By controlling the pH values of prepared solutions, the 10 mol% Ce³⁺, 5 mol% Tb³⁺ co-doped KGdF₄ (synthesized with pH = 3) and the 10 mol% Ce³⁺, 5 mol% Tb³⁺ co-doped GdF₃ (synthesized with pH = 1) submicro/nanocrystals have been synthesized based on a citric acid assisted hydrothermal method. For comparison, the samples synthesized by co-precipitation method (without hydrothermal treatment) with pH = 3 and 1 were also collected. The X-ray diffraction data illustrate that the hydrothermal treated KGdF₄ sample crystallizes in the cubic phase and the GdF₃ sample crystallizes in the orthorhombic phase. However, the samples synthesized by co-precipitation method with pH = 3 and 1 are both cubic phase KGdF₄. The field emission scanning electron microscopy images suggest that the hydrothermal treated KGdF₄ submicro/nanocrystals present spherical morphology and the GdF₃ submicrocrystals are rhombic-shaped. And the photoluminescence excitation and emission spectra as well as the luminescent dynamic curves demonstrate the difference in optical properties of the two hydrothermal treated samples.     

Sonochemical synthesis of versatile hydrophilic magnetite nanoparticles

Hydrophilic magnetite nanoparticles in the size range 30-10 nm are easily and rapidly prepared under ultrasonic irradiation of Fe(OH)₂ in di- and tri-ethylene glycol/water solution with volume ratio varying between 7:3 and 3:7.Structural (XRD) and morphological (SEM) characterization reveal good crystalline and homogeneous particles whereas, when solvothermally prepared, the particles are inhomogeneous and aggregated. The sonochemically prepared particles are versatile, i.e. well suited to covalently bind molecules because of the free glycol hydroxylic groups on their surface or exchange the diethylene or triethylene glycol ligand. They can be easily transferred in hydrophobic solvents too.Room-temperature magnetic hysteresis properties measured by means of Vibrating Sample Magnetometer (VSM) display a nearly superparamagnetic character.The sonochemical preparation is easily scalable to meet industrial demand.     

Excimer laser accelerated hydrothermal synthesis of ZnO nanocrystals & their electrical properties

The synthesis of ZnO nanocrystals is reported using a hydrothermal chemical growth technique combined with 248 nm nanosecond excimer laser heating at fluences in the range 0-390 mJ cm⁻². The effect of laser heating in controlling the morphology of the nanocrystals is investigated using optical spectroscopy and electron microscopy characterization. Laser heating is shown to allow control of the crystal morphology from nanoparticles to nanorods as well as to modify the size distributions. The results indicate that not only does the laser accelerate the growth of nanocrystals, but can also produce crystals with a narrow size distribution possibly via photothermal size selection. An initial study of electrical conduction properties of ZnO nanocrystal thin films is also discussed.     

Structure and magnetic properties of flower-like α-NiS nanostructures

In this paper we report the structure and magnetic properties of flower-like α-NiS nanostructure prepared by a facile one-step hydrothermal method. The flowers consist of polycrystalline nanoflakes, and the nanoflakes are composed of single crystalline nanocrystals with an average size of about 15 nm. The α-NiS flowers exhibit the transition from paramagnetism to ferromagnetism with the blocking temperature of about 12 K. The field dependences of the magnetization prove that these flowers demonstrate a coexistence of antiferromagnetism and ferromagnetism at 5 K, and exhibit a strong paramagnetic response at temperature higher than 100 K.     

Zinc oxide nano-particles--sonochemical synthesis, characterization and application for photo-remediation of heavy metal

Zinc oxide nanoparticles have been synthesized sonochemically from zinc acetate solution in aqueous methanol, ethanol and iso-propanol containing about 5 volume% of alcohol. Characterization with FESEM, XRD, AFM and BET surface area shows that the synthesized particles differ in shape and size. ZnO synthesized using isopropanol was observed to be the most crystalline one. The synthesized nanoparticles were used for the photocatalytic reduction of hexavalent chromium in aqueous medium under solar radiation. It was observed that the initial reduction rates varied with the difference in morphology of ZnO crystallites.     

Highly sensitive breath sensor based on sonochemically synthesized cobalt-doped zinc oxide spherical beads

In this study, we introduce cobalt (Co)-doped zinc oxide (ZnO) spherical beads (SBs), synthesized using a sonochemical process, and their utilization for an acetone sensor that can be applied to an exhalation diagnostic device. The sonochemically synthezied Co-doped ZnO SBs were polycrystalline phases with sizes of several hundred nanometers formed by the aggregation of ZnO nanocrystals. As the Co doping concentration increased, the amount of substitutionally doped Co²⁺ in the ZnO nanocrystals increased, and we observed that the fraction of Co³⁺ in the Co-doped ZnO SBs increased while the fraction of oxygen vacancies decreased. At an optimal Co-doping concentration of 2 wt%, the sensor operating temperature decreased from 300 to 250 °C, response to 1 ppm acetone improved from 3.3 to 7.9, and minimum acetone detection concentration was measured at 43 ppb (response, 1.75). These enhancements are attributed to the catalytic role of Co³⁺ in acetone oxidation. Finally, a sensor fabricated using 2 wt% Co-doped ZnO SBs was installed in a commercially available exhalation diagnostic device to successfully measure the concentration of acetone in 1 ml of exhaled air from a healthy adult, returning a value of 0.44 ppm.     

Shape alterations of ZnO nanocrystal arrays fabricated from NH3·H2O solutions

Well-aligned crystalline ZnO nanorod arrays were synthesized via an aqueous solution route with ammonia and zinc nitrate as inorganic precursors. ZnO crystalline seed films were firstly coated on ITO substrates for epitaxial growth of rods through sol-gel processing and heat treatment. SEM, TEM, SAED and XRD were utilized to characterize morphologies and structures of ZnO crystals. Heterogeneous nucleation is crucial for rod growth. A broad scope of pH favorable for heterogeneous nucleation was disclosed at zinc concentration from 0.04 to 0.1 M in the inorganic system due to the complex reaction of ammonia with Zn²⁺. Elevation of initial zinc concentration or pH promoted growth rate of rods and enlarged rod size. ZnO nanorods were transformed to nanotubes, nanosheets and rods with blanket-like shaped surface mainly by secondary pH adjustment. All ZnO nanocrystals are wurtzite structure preferentially oriented in c-axis direction.     

Excitation wavelength dependent photoluminescence intensity of six faceted prismatic ZnO microrods

This article presents the investigation on the large-scale synthesis of ZnO microrods with a simple low temperature hydrothermal method without using surfactants, organic solvents, or catalytic reagents. The synthesized ZnO powder is characterized with different techniques. The X-ray diffraction study reveals the excellent crystal quality of the ZnO product possessing the hexagonal (wurtzite-type) crystal structure. The scanning electron microscope observation confirms the formation of six faceted prismatic hexagonal ZnO microrods with the aspect ratio of 10. It also reveals that the ZnO microrods grow along the (0 0 0 1) direction and finally emerge with a sharp tip because of the existence of polar faces. The UV–vis spectrum shows a sharp absorption peak centered at 370 nm, which is in a good agreement with the equivalent bulk band gap value. The strong UV absorption peak implies the excellent crystal quality of the synthesized ZnO microrods. Room temperature photoluminescence spectroscopic study of the ZnO microrods with different excitation wavelengths reveals a strong band edge emission peak centered at 398 nm and a defect related visible blue emission peak at 460 nm. The decrease in photoluminescence intensity with negligible red shift in peak position is observed with increasing excitation wavelength.     

Plate-like hydroxyapatite nanoparticles synthesized by the hydrothermal method

In this article, calcium nitrate (Ca(NO₃)₂) and disodium hydrogen phosphate (Na₂HPO₄) are used as calcium and phosphorous sources to prepare hydroxyapatite nanoparticles by the hydrothermal method. Plate-like nanocrystals of hydroxyapatite are synthesized with the aid of sodium tripolyphosphate. The results show that sodium tripolyphosphate increases the diameters of the hydroxyapatite nanoparticles during the hydrothermal process. When the concentration of sodium tripolyphosphate reaches 0.015 M, the average aspect ratio of those nanoparticles is close to 1. The strong surface adsorption caused by sodium tripolyphosphate may answer for the morphological change of hydroxyapatite crystal.     

A complexant-assisted hydrothermal procedure for growing well-dispersed InP nanocrystals

Well-dispersed InP nanocrystals have been synthesized via a hydrothermal reaction of In–ethylenediamine tetraacetic acid (EDTA) complex with red phosphorus and KBH₄ in aqueous solution at 160–200 °C for 26 h. The InP nanocrystals were characterized by powder X-ray diffraction (XRD), Raman spectroscopy and transmission electron microscopy (TEM). The XRD patterns showed (1 1 1), (2 0 0), (2 2 0), (3 1 1), (2 2 2), (4 0 0) and (3 3 1) diffraction lines of the cubic InP nanocrystals. The TEM study revealed that the morphology of InP nanocrystals are of well-dispersed spherical shape. The size of InP nanocrystals can be controlled by changing the reaction temperature. The average InP nanocrystallites diameter is increased from 8.7 to 15.8 nm as the temperature increases from 160 to 200 °C. The Raman spectrum showed the transverse-optic (TO) and longitudinal-optic (LO) mode from InP nanocrystallites, and the LO and TO modes shift to lower frequencies with a decrease in the size of InP nanocrystals. The EDTA plays a key role in the nucleation and growth of InP nanocrystals, and the reaction mechanism is discussed.     

Sonochemical growth of antimony selenoiodide in multiwalled carbon nanotube

This paper presents, for the first time, the nanocrystalline, semiconducting antimony selenoiodide (SbSeI) grown in multi-walled carbon nanotubes (CNTs). It was prepared sonochemically using elemental Sb, Se, and I in the presence of ethanol under ultrasonic irradiation (35 kHz, 2.6 W/cm²) at 323 K for 3 h. The CNTs filled with SbSeI were characterized by using techniques such as powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, high-resolution transmission electron microscopy, selected area electron diffraction, and optical diffuse reflection spectroscopy. These investigations exhibit that the SbSeI filling the CNTs is single crystalline in nature and in the form of nanowires. It has indirect allowed energy band gap E_gIf = 1.61(6) eV.     

Fast two-step microwave-activated synthesis of Mn doped ZnS nanocrystals: Comparison of the luminescence and doping process with thermochemical approach

In this work we report a fast two-step microwave activated synthesis of the ZnS:Mn nanocrystals. Zn(NO₃)₂ and Na₂S₂O₃ were used as the precursors and Mn(NO₃)₂ was employed as the source of the impurity. The aqueous synthesis was based on the heat sensitivity of Na₂S₂O₃, which releases some S species on heating. Consequently, the reaction was well activated under microwave irradiation resulting in formation of ZnS:Mn nanocrystals. Thioglycerol (TG) was also used as the capping agent and the catalyst of the reaction. The synthesis process was done in two steps, i.e. 1 min irradiation without TG and then injection of TG and continuation of irradiation. ZnS:Mn nanocrystals were quickly formed in the solution and luminescence was emerged in a few minutes. Optical transmission spectroscopy and X-ray diffraction analysis demonstrated formation of ZnS:Mn nanocrystals with a cubic crystalline structure and 3.0 nm average size. Photoluminescence measurements also showed some spectra with a Mn related peak located at 585 nm. The mentioned peak corresponds to ⁴T₁→⁶A₁ transition in Mn impurities and revealed the effective incorporation of Mn ions inside the nanocrystals. Evolution of the PL was also investigated and showed an increase in longer irradiation times. A qualitative model is also used to justify the necessity of using a two-step method as well as the PL emergence and increase in longer irradiation times. The model is based on separation between the nucleation and growth steps and significant role of TG in these stages. Finally, we present a comparison between the results of microwave activated method and two-step thermochemical approach. Although the synthesis time in microwave activated method was considerably short (less than 5 min), the luminescence properties were quite comparable with long time thermochemical approach. The doping process was also investigated for different Mn/Zn concentrations in two approaches. The results demonstrated that the doping occurred more effectively in the microwave activated synthesis.     

Hydrothermal synthesis and Magnetocaloric effect of La0.5Ca0.3Sr0.2MnO3

The hydrothermal synthesis and magnetic entropy change for the perovskite manganite La_0.5Ca_0.3Sr_0.2MnO₃ have been studied. The La_0.5Ca_0.3Sr_0.2MnO₃ can be produced as phase-pure, crystalline powders in one step from solutions of metal salts in aqueous potassium hydroxide solution at a temperature of 513 K in 72 h. Scanning electron microscopy shows that the materials are made up of cuboid-shaped particles in typical dimension of 4.0×2.5×1.6 μm. Heat treatment can improve the magnetocaloric effect for the hydrothermal sample. The maximum magnetic entropy change ΔS_M for the as-prepared sample is 0.88 J kg⁻¹ K⁻¹ at 315 K for a magnetic field change of 2.0 T. It increases to 1.52 J kg⁻¹ K⁻¹, near its Curie temperature (317 K) by annealing the sample at 1473 K for 6 h. The hydrothermal synthesis method is a feasible route to prepare high-quality perovskite material for magnetic refrigeration application.     

Ultrasonic assisted synthesis of Bikitaite zeolite: A potential material for hydrogen storage application

Li containing Bikitaite zeolite has been synthesized by an ultrasound-assisted method and used as a potential material for hydrogen storage application. The Sonication energy was varied from 150 W to 250 W and irradiation time from 3 h to 6 h. The Bikitaite nanoparticles were characterized by X-ray diffraction (XRD), infrared (IR) spectral analysis, and field-emission scanning electron microscopy (FESEM) thermo-gravimetrical analysis and differential thermal analysis (TGA, DTA). XRD and IR results showed that phase pure, nano crystalline Bikitaite zeolites were started forming after 3 h irradiation and 72 h of aging with a sonication energy of 150 W and nano crystalline Bikitaite zeolite with prominent peaks were obtained after 6 h irradiation of 250 W sonic energy. The Brunauer–Emmett–Teller (BET) surface area of the powder by N₂ adsorption–desorption measurements was found to be 209 m²/g. The TEM micrograph and elemental analysis showed that desired atomic ratio of the zeolite was obtained after 6 h irradiation. For comparison, sonochemical method, followed by the hydrothermal method, with same initial sol composition was studied. The effect of ultrasonic energy and irradiation time showed that with increasing sonication energy, and sonication time phase formation was almost completed. The FESEM images revealed that 50 nm zeolite crystals were formed at room temperature. However, agglomerated particles having woollen ball like structure was obtained by sonochemical method followed by hydrothermal treatment at 100 °C for 24 h. The hydrogen adsorption capacity of Bikitaite zeolite with different Li content, has been investigated. Experimental results indicated that the hydrogen adsorption capacities were dominantly related to their surface areas as well as total pore volume of the zeolite. The hydrogen adsorption capacity of 143.2 c.c/g was obtained at 77 K and ambient pressure of (0.11 MPa) for the Bikitaite zeolite with 100% Li, which was higher than the reported values for other zeolites. To the best of our knowledge, there is no report on the synthesis of a Bikitaite zeolite by sonochemical method for H₂ storage.     

Stability and textural properties of cobalt incorporated MCM-48 mesoporous molecular sieve

Transition metal cobalt incorporated MCM-48 mesoporous molecular sieves (CoMCM-48) with different Co contents were synthesized hydrothermally at 120 °C for 24 h by directly adding fluoride ions to the initial gel. The resulting materials were characterized by means of XRD, TEM, FT-IR, UV-vis, TPR and N₂ physical adsorption, respectively. The effect of various factors, such as the Si/Co molar ratio, calcination temperature and hydrothermal treatment time, on the crystalline structure and textural properties of CoMCM-48 was investigated in detail. The results show that the CoMCM-48 mesoporous materials with high specific surface area were successfully synthesized. A small amount substitution of Co for Si in MCM-48 did not significantly change the textural properties while the higher cobalt incorporated leads to decrease of the surface area and deterioration of structural regularity. Furthermore, the resulting CoMCM-48 still retained the cubic mesoporous framework even after calcination at 800 °C for 4 h or hydrothermal treatment at 100 °C for 24 h.     

Highly efficient cathodoluminescence of nanophosphors by solvothermal route

The low voltage excited nano-size of SrTiO₃: Pr, Al red cathodoluminescent phosphors is successfully prepared by hydrothermal and solvothermal processes. Crystal size does not have obvious growth after post-annealing process under the nucleation seeds control. The nanophosphors synthesized by the solvothermal process have a more stoichiometric and cubic SrTiO₃ structure than the hydrothermal ones. SrTiO₃: Pr, Al nanophosphors synthesized by the solvothermal process with 200 °C/24 h possess a cubic crystal size of about 50 nm. The red cathodoluminescent intensity of 200 °C/24 h-solvothermal phosphors is nine times that of the 250 °C/24 h-hydrothermal ones after 1000 °C/1 h heat treatment. The stoichiometric SrTiO₃: Pr, Al nanophosphors by solvothermal preparation need less amounts of Pr activator and Al dopant than when using conventional solid-oxide preparation and can achieve high cathodoluminescence at a wavelength of 615 nm exciting at a low accelerating voltage of 1 kV. The solvothermal process combined with the post-annealing process to synthesize nanophosphors distributes and excites the activator and the dopant more homogeneously and efficiently in the host structure of SrTiO₃, thus enhancing luminescence.     

Effects of growth duration on the structural and optical properties of ZnO nanorods grown on seed-layer ZnO/polyethylene terephthalate substrates

Well-aligned single crystalline zinc oxide (ZnO) nanorods were successfully grown, by hydrothermal synthesis at a low temperature, on flexible polyethylene terephthalate (PET) substrates with a seed layer. Photoluminescence (PL), field-emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM) measurements were used to analyze the optical and structural properties of ZnO nanorods grown for various durations from 0.5 h to 10 h. Regular and well-aligned ZnO nanorods with diameters ranging from 62 nm to 127 nm and lengths from 0.3 μm to 1.65 μm were formed after almost 5 h of growth. The growth rate of ZnO grown on PET substrates is lower than that grown on Si (1 0 0) substrates. Enlarged TEM images show that the tips of the ZnO nanorods grown for 6 h have a round shape, whereas the tips grown for 10 h are sharpened. The crystal properties of ZnO nanorods can be tuned by using the growth duration as a growth condition. The XRD and PL results indicate that the structural and optical properties of the ZnO nanorods are most improved after 5 h and 6 h of growth, respectively.