机载北斗/GPS/SINS组合导航系统软硬件设计

针对单一导航导航系统在导航精度、稳定性、设备成本以及导航信息完备性等方面的局限性,设计了卫星导航/惯性导航组合导航系统。针对GPS导航系统受制于人及北斗导航系统发展尚不完善的特点,提出了基于北斗/GPS/SINS的军用机载组合导航系统软硬件设计。搭建了北斗/GPS/SINS组合导航系统硬件平台,采用基于不确定度的加权平均数据融合算法提高组合导航系统的导航可靠性和准确性。仿真结果表明,该组合导航系统稳定性好,可靠性高,定位准确。     

Kalman滤波辅助的室内伪卫星相对定位算法

在室内伪卫星独立定位系统中, 伪卫星以及接收机的钟差会给定位精度带来非常大的误差. 针对这一问题, 提出了一种适用于室内环境的相对定位算法. 使用Kalman定位算法粗略计算接收机位置, 获得粗略基线, 建立室内相对定位模型, 得到载波相位双差和伪距双差. 载波相位双差通过互补Kalman滤波器来平滑伪距双差, 进一步得到精确基线, 获得接收机精确位置, 并将其代替Kalman定位算法的校正结果, 对接收机进行下一状态预测. 实验结果表明, 该算法具有较高的定位精度, 定位误差在20 cm以内. 关键词： 伪卫星 相对定位 双基线 Kalman滤波     

一种基于多源收发异体结构的室内移动目标超声定位系统

提出一种高性能超声定位系统,采用红外和无线信号同时作为同步信号构成收发异体的定位结构,采用伪随机M序列进行载波扩频,形成码分多址的多基站收发机制,通过设计广角探头来扩大作用范围,设计温度补偿电路提高测量精度.本系统能实现10 Hz的测量速率和厘米级的测量精度,能有效实现室内移动目标的高精度定位.     

无人机侦察多目标实时定位技术研究

目标定位是无人机侦察系统中至关重要一步。为增强无人机侦察目标定位的实时性、提高定位精度及侦察效率,提出一种多目标实时定位的方法,建立主次目标定位几何关系及坐标转换模型,结合已知数据信息求取各目标大地坐标,并用蒙特卡洛法分析目标定位误差。最后,基于即将组网成功"北斗二代"卫星导航系统对无人机空中定位,同时采用递归最小二乘算法滤波处理,提高了目标定位精度。研究及实验结果表明,北斗导航定位能够有效提高无人机空中定位精度,且有望达到厘米级精度,同时采用RLS滤波处理能使目标定位精度提高10 m左右。该方法能够有效增强无人机定位实时性,提高定位精度及侦察效率。     

基于惯性信息辅助的北斗动动定位方法的研究

针对北斗动动定位中接收机信号易受遮挡导致无法实时准确定位的问题,对复杂信号条件下的动动定位测试进行了研究,提出了一种利用惯性信息辅助解算动态模糊度的方法,即一种将运动载体的惯导信息与北斗测量信息相结合,实现两运动载体之间精确动态相对定位的算法。通立基于载波相位双差的观测模型,采取融合滤波算法,讨论在在不同卫星数目下的模糊度求解方法。在此基础上,利用实地车载试验完成了对上述组合定位方法的试验验证以及精度测试,事后着重对各历元数据进行解算,对定位精度、可用性进行了研究。结果表明,基于惯性信息辅助的北斗动动定位可用性指标变好,定位精度有一定的提高。     

基于影像实时处理的加油对接段辅助对准技术北大核心CSCD

针对空中加油试飞中加油对接困难的问题,设计了一种基于影像实时处理的加油对接段辅助对准系统,通过影像测量技术计算受油头与加油锥套中心的精确相对位置,实现位置参数与视频画面实时同步显示,用于空中加受油对接辅助对准。并对复杂光学条件下锥套跟踪技术、基于约束的像机标定技术和加受油组件相对位置实时测量等关键技术进行研究。实验结果表明,该算法可实现空中复杂环境下锥套图像快速、稳定识别与跟踪;采用双目视觉前方交会测量实时计算加油锥套与受油头相对位置,与事后处理结果对比分析,精度优于0.1 m,可辅助飞行员进行空中加油对接操作,提高加受油对接成功率。     

机载卫星制导武器直接瞄准攻击研究

 介绍了卫星制导武器直接瞄准攻击方式在对地精确打击中占据的关键位置,阐述了卫星制导武器直接瞄准攻击方法的原理。由于卫星制导武器直接瞄准攻击对目标定位要求较高,采用常用定位手段已不能满足系统对目标定位的要求,分析了使用相对GPS制导成为卫星制导武器直接瞄准攻击的关键的原因。相对GPS制导误差主要包括采用载机和武器相对GPS定位误差以及传感器对目标的相对定位误差,分别对两者的定位精度进行了分析和推导。仿真结果表明：这两者的综合误差理论值小于7.5 m,满足卫星制导武器在直接瞄准攻击中对目标定位的需求。     

近景大视场角分区域标定方法研究

针对飞行试验测量视场大相机标定精度低的问题,提出一种高精度CCD相机分区域标定方法。该方法首先通过将标靶均匀布置在摄像机视场内,使得标靶尽可能均匀错落地充满整个视场范围,再结合人眼判读的方式求解靶标的像面位置,最终与全站仪三维坐标形成精确的空间标定点集。接着,将像平面按横向方向等间距分割成Ｎ个区域,并结合后方交会的方法分别对每个子区域进行相机参数的计算。实验结果表明：经过分区域标定,相机采集点的总误差比单区域标定法降低了4％(Ｎ＝3)。算法可实现指定区域的相机参数计算,基本满足中高等精度的工业测量要求。所本文研究可应用于位置相对固定不变的工业视觉测量,特别是大工件测量领域。     

微靶装配中靶球几何量的高精度测量

为满足微靶装配过程中靶球和靶腔相对位置的严格的要求,保障惯性约束聚变实验的成功,针对机器视觉的几何量测量精度很难达到5 m以下的不足,设计了利用具有亚m级精度的激光共焦测头对装配中的靶球进行采点扫描以获取其尺寸和位置的非接触测量方法,借助于在线监测系统运动轴的高精度定位,通过上下两个激光共焦测头的组合测量,并采用一种快速而准确的基于点阵插值细分和目标两级提取的测量算法,使在线监测系统的球体几何量测量精度达到了2 m。     

利用GNSS差分的天线阵大气相位扰动实时修正方法

提出了一种基于全球导航卫星系统差分的天线阵大气相位扰动实时修正方法,以高稳定度的原子钟作为外频标,利用导航卫星载波相位的单差与历元上的双差,并通过星历扣除由于卫星运动引起的相位变化,在周跳检测和修正后,通过长周期的拟合消除卫星轨道和站坐标误差的影响,最后通过双频或多频信号实现两地电离层和对流层扰动的实时测量.在国家天文台北京密云站和云南昆明站分别部署了一套全球导航卫星接收设备,进行异地大气相位扰动实时修正方法的实验验证.利用双频载波相位测量数据对第三频率进行修正,结果表明,在不同天气条件下修正后的大气相位扰动均方根达到1.9mm,表明该方法可用于射电天文和深空探测中天线阵的大气相位扰动修正.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.     

Direction-of-arrival estimation using matrix spatial prefiltering approach

An approach to direction-of-arrival （DOA） estimation for multiple narrowband farfield signals is proposed. The technique uses a novel matrix spatial prefiltering approach. Specifically, a matrix filter is designed to spatially filter the incoming data snapshots. The un-wanted components arriving from the stopband angular sectors are attenuated and the desired components from the angular sector of interest pass with minimal distortion. The matrix filter spatially filters the element-space data and the output reserves the element-space data property, which makes it very useful by passing sensor data through a spatial prefilter prior to applying many other array processors to attenuate interferences and improve system performance. Several examples of DOA estimation problem are presented to illustrate the performance of the proposed spatial prefiltering approach. Results of simulation and real data show that the pre-filter can efficiently attenuate the spatial interferences and significantly improve the estimation and resolution capability of DOA estimators at low signal-to-noise ratios for the sources located inside the passband sector. In addition, the use of spatial prefilter makes it possible to estimate DOAs for multiple sources more than the number of the elements of an array.     

Quantum efficiency calibration of opto-electronic detector by means of correlated photons method

A new calibration method of detectors can be realized by using correlated photons generated in spontaneous parametric down-conversion (SPDC) effect of nonlinear crystal.An absolute calibration system of detector quantum efficiency is performed.And its principle and experimental setup are introduced.A continuouswave (CW) ultraviolet (351 nm),diode-pumped,frequency-doubled,and solid-state laser is used to pump BBO crystal.The quantum efficiencies of the photomultiplier at 633,702,and 789 nm are measured respectively.The coincidence peaks are observed using coincidence circuit.Some measurement factors including the filter bandwidth of trigger channel,the detector position alignment and polarization of the pump light are analyzed.The uncertainties of this calibration method are also analyzed,and the relative uncertainties of total calibration are less than 5.8%.The accuracy of this method could be improved in the future.