加热基底上附壁液滴蒸发动力学实验研究

为了了解液滴表面热流型演变规律及其对蒸发速率的影响,采用稳态蒸发实验研究了加热基底上乙醇和水滴的蒸发过程。液滴半径固定在R=2.5 mm,高度变化范围为0.4至1.4 mm。结果表明,随着液滴高度降低,乙醇液滴表面出现了中心不均匀的温度波动、热流体波及Bénard-Marangoni流胞,而水滴表面则没有明显温度波动。随着基底温度升高,液滴内部热对流增强;随着液滴高度降低,乙醇液滴蒸发速率先减小、后增大,而水滴蒸发速率则无明显变化。实验结果证实热对流对液滴蒸发速率具有明显促进作用。     

液滴撞击热壁面的相变行为研究

本文基于格子Boltzmann方法建立了液滴撞击热壁面的数学模型,研究了撞击过程液滴相变传热机制,重点分析了壁面温度与We数的影响规律.结果表明,随着壁面温度升高,液滴撞击壁面出现接触沸腾、膜态沸腾相变模式.接触沸腾过程中液滴内部与壁面接触的三相线附近出现最大局部热流.当壁面温度超过Leidenfrost点后,撞击液滴因界面蒸发产生的气膜托举作用而与壁面无接触地铺展、回缩直至完全反弹形成膜态沸腾,这一阶段液滴所能达到的最大铺展因子与液滴We数呈幂次关系(指数为0.313).     

电场作用下纳米流体液滴在超疏水热表面蒸发特性的研究

本文研究了平行电场中超疏水热表面上氧化石墨烯纳米流体液滴的蒸发特性.利用可视化技术捕捉了液滴接触角、接触直径及瞬态相界面的变化.实验发现平行电场能够将液滴沿电势梯度方向拉伸成椭球状,并可以调控蒸发过程中液滴接触直径的变化过程及大小.当液滴接触直径收缩比减小至某一临界值后,将出现一种新的蒸发模式:接触角与接触直径均保持不...     

单液滴冲击超疏水壁面的压力特性研究

雨滴撞击索类结构表面可能会激发振动及表面积冰等问题,现有研究多关注于疏水壁面及液滴撞击壁面铺展、回缩特性,鲜见涉及雨滴冲击超疏水壁面压力特性的研究.为此,采用CLSVOF方法对单液滴冲击超疏水固壁面这一过程进行数值计算,分析了液滴速度、初始直径等因素对液滴冲击超疏水壁面的压力特性、液滴动态行为特性及液滴与壁面接触时间的影响.结果 表明:单液滴撞击超疏水壁面的过程中,接触瞬间在接触点附近产生局部高压区,而在液滴铺展过程中,对壁面几乎没有压力冲击;在回缩反弹阶段,壁面受到持续较长时间的压力波动,且压力波动区域不局限于初始接触点附近较小范围.撞击速度或液滴初始直径的增大使壁面受到的冲击更为剧烈,且初始速度对壁面受压的影响更为明显.一定范围内液滴初始直径的增大则会导致接触时间延长.     

不同直径液滴撞击亲水壁面动态特性实验研究

本文通过可视化实验研究了不同直径液滴撞击亲水壁面的动态特性.实验利用光学原理同时记录了液滴撞击壁面过程的正面及底面图像。实验结果表明:液滴最大铺展因数随液滴初始直径近似呈线性增长关系;随液滴直径增大,液滴铺展至最大时需要的绝对时间、滞留时间、回缩时间均增长,稳定时的液固接触面积变大;液滴铺展至最大铺展因数所需要的无量纲时间约为1.68;液滴直径越小,则撞击后液膜回缩更为迅速.     

低温光滑壁面上水滴撞击结冰行为

采用高速摄像技术测试低温光滑壁面上水滴撞击结冰过程, 分析了撞击速度、壁面温度和材料热导率对水滴撞击铺展、振荡及结冰行为的影响规律. 结果表明, 低温壁面造成水滴最大铺展直径缩小, 且结冰时间随温度降低而缩短; 当撞击We数提高时, 水滴最大铺展直径增大, 而振荡和结冰时间减小; 同时材料热导率越高, 最大铺展直径越小, 结冰越迅速. 另外, 从热力学角度推导出水滴撞击结冰时间的理论公式, 预测误差<5.3%.     

倾斜均质表面上等径水滴聚合过程的可视化实验

对倾斜均匀表面上等直径水滴的聚合过程及特性进行了可视化实验研究,获得了水滴直径和表面倾角等参数对液滴聚合过程中液滴液桥半径、接触角和接触线变化特性的影响,分析了水滴聚合对其运动的影响.实验结果表明:表面倾角越大,下滑的临界半径越小;液滴的直径越大,液滴聚合后越容易下滑;液滴聚合可以加快液滴的运动,使下滑临界半径减小.     

剪切变稀液滴撞击不同浸润性壁面的数值模拟研究

基于有限元法,采用水平集方法捕捉相界面的移动,构建了液滴撞击固体壁面的数值模型.通过修正的幂律模型描述流体的非牛顿剪切变稀特性,探讨了剪切变稀特性对液滴撞击固体壁面后铺展行为的影响,分析了撞击不同浸润性壁面时剪切变稀特性对液滴撞击壁面行为的影响差异.研究结果表明:随着幂律指数m的减小,液滴撞击过程中的黏性耗散减小,液滴的形貌变化及无量纲参数变化更为显著.接触角为55°的情况下:当m降低至0.85时,液滴铺展过程中开始出现显著区别于牛顿流体液滴的振荡现象;当m降低至0.80时,液滴在回缩过程中会出现中心液膜断裂的情况.接触角为100°时,剪切变稀液滴均会出现振荡行为,振荡幅度随着m的减小而增大.接触角为160°时,牛顿流体液滴与剪切变稀液滴均会在回缩过程中弹起,但剪切变稀液滴的弹起速度更快.此外,基于数值计算结果,本文提出了接触角为55°情况下剪切变稀液滴撞击壁面后的最大无量纲铺展直径预测模型.     

离子液体液滴在加热平板上的铺展特性研究

采用FLIR红外热像仪对离子液体及其水溶液液滴撞击加热平板后的表面温度分布进行研究,分析了液滴铺展直径随平板加热温度及加热时间的变化规律。结果表明:随着液滴与平板加热时间的增加,液滴表面温度分布均由凹状分布变化至均匀分布;随着平板温度的增加,液滴表面温度增加。随着加热时间的增加,水液滴直径缓慢减小,并在某一时刻急剧降低;而对于60wt%离子液体液滴及纯离子液体液滴,液滴直径反而缓慢增加并趋于稳定。随着加热温度的增加,水液滴直径急剧降低的时刻点前移,对于60wt%离子液体溶液液滴,液滴直径变化规律不明显,而对于纯离子液体液滴,液滴直径逐渐增加。     

平衡接触角对受热液滴在水平壁面上铺展特性的影响

壁面温度是影响壁面润湿性的重要外部条件. 为解决液滴铺展中三相接触线处应力集中问题, 已有研究多采用预置液膜假设, 但无法探究壁面温度对润湿性的影响. 本文针对受热液滴在固体壁面上的铺展过程, 基于润滑理论建立了演化模型, 通过数值模拟, 从平衡接触角角度分析了温度影响壁面润湿性及铺展过程的内部机理. 研究表明: 随温度梯度增大, 液滴所受Marangoni效应增强, 致使液滴向低温区的铺展速率加快; 铺展过程中, 位于高温区的接触线与液滴主体部分间形成一层薄液膜, 重力与热毛细力先后主导该区域的铺展; 当液-固或气-液界面张力对温度的敏感度高于另两个界面时, 低温区方向的平衡接触角不断增大, 使壁面润湿性恶化, 导致液滴铺展减慢; 而当气-固界面张力对温度的敏感度高于其他两个界面时, 低温区方向上的平衡接触角将减小, 由此改善壁面润湿性, 加快液滴铺展; 在温度影响壁面润湿性和液滴铺展过程中, 平衡接触角起关键作用.     

Continuous droplet rebound on heated surfaces and its effects on heat transfer property: A lattice Boltzmann study

A thermal multiphase lattice Boltzmann(LB) model is used to study the behavior of droplet impact on hot surface and the relevant heat transfer properties.After validating the correctness of the codes through the D~2 law,the simulations of intrinsic contact angle and the temperature-dependent surface tension are performed.The LB model is then used to simulate the droplet impact on smooth and micro-hole heated surface.On the smooth surface,the impinging droplet is reluctant to rebound,unless the intrinsic wettability of the solid surface is fairly good.On the micro-hole surface,however,the micro-holes provide favorable sites for generating a high-pressure vapor cushion underneath the impinging droplet,which thereby facilitates the continuous droplet rebound.For the continuously rebounding droplet.The time evolution of volume and temperature display obvious oscillations.The achievable height of the rebounding droplet increases as the intrinsic wettability of the solid surface becomes better,and the maximum transient heat flux is found to be directly proportional to the droplet rebounding height.Within a certain time interval,the continuous rebounding behavior of the droplet is favorable for enhancing the total heat quantity/heat transfer efficiency,and the influence of intrinsic wettability on the total heat during droplet impingement is greater than that of the superheat.The LB simulations not only present different states of droplets on hot surfaces,but also guide the design of the micro-hole surface with desirable heat transfer properties.     

过冷水滴碰撞结冰的实验与模拟研究

以宏观结冰/霜过程中过冷水滴的碰撞结冰现象为背景,实验对比了亲水和超疏水表面上常温水滴碰撞、常温水滴碰撞结冰和过冷水滴碰撞结冰的过程,建立了过冷水滴碰撞结冰过程的数值模型,研究了We数和接触角对碰撞结冰的影响。结果表明:相比于常温水滴的碰撞及其碰撞结冰过程,过冷水滴碰撞结冰过程的稳态铺展系数更大;随着过冷度和We数的增大以及接触角的减小,过冷水滴的碰撞结冰与常温水滴的碰撞在水滴形态和铺展系数上的差异逐渐增大。     

Evaporation of liquid droplets from a surface of anodized aluminum

The results of study of evaporation of water droplets and NaCl salt solution from a solid substrate made of anodized aluminum are presented in this paper. The experiment provides the parameters describing the droplet profile: contact spot diameter, contact angle, and droplet height. The specific rate of evaporation was calculated from the experimental data. The water droplets or brine droplets with concentration up to 9.1 % demonstrate evaporation with the pinning mode for the contact line. When the salt concentration in the brine is taken up to 16.7 %, the droplet spreading mode was observed. Two stages of droplet evaporation are distinguished as a function of phase transition rate.     

Heat flux density in the region of droplet contact line on a horizontal surface of a thin heated foil

The evaporating water droplets on a horizontal heated substrate were experimentally studied. The constantan foil 25 μm thick with a size of 42×35 mm² was used as a substrate. The experiments were carried out with a single droplet or with an ensemble of two or three droplets on the foil. The temperature of the lower surface of foil was measured by an IR scanner. To determine the heat flux density at evaporation of liquid near the contact line, the Cauchy problem for the heat conduction equation was solved using the thermographic data. The results of calculations showed that the maximal heat flux density takes place in the region of the contact line and exceeds the average heat flux density from the entire surface of foil. This is explained by the heat inflow from the foil periphery to the droplet due to relatively high value of the coefficient of heat conductivity of the foil material and high evaporation intensity in the contact line region.     

双液滴撞击平面液膜的流动与传热特性

采用耦合的水平集-体积分数法(CLSVOF)对双液滴连续撞击恒定壁温壁面上的热液膜的流动和换热特性进行了数值模拟及分析,得到了双液滴撞击热液膜后形态演变的过程.分析了液滴垂直间距、撞击速度、液膜厚度以及液滴直径对双液滴撞击液膜后的流动与传热特性的影响,结果显示,壁面平均热流密度随液滴撞击速度的增大而增大,液滴垂直间距、液膜厚度和液滴直径对平均热流密度的影响较小,但会对热流密度在撞击区域和交界区的分布产生重要影响.     

A GENERAL HEAT TRANSFER CORRELATION FOR IMPACTING WATER SPRAYS ON HIGH-TEMPERATURE SURFACES

A method for the general correlation of heat transfer effectiveness for sprays impacting vertically downward on a high-temperature surface has been developed. A dimensional analysis showed that the mass velocity of the spray can be substituted for the droplet velocity in the droplet Reynolds and Weber numbers, greatly improving the correlation with the heat flux data in the film boiling regime. The spray Reynolds number, defined as Re s = Gd/ w , and spray Weber number, We s = G 2 d/ 𝜌 σ , were shown to correlate data from many authors covering a wide range of spray parameters. This correlation supports the results of previous parametric experiments, and is analogous to correlations developed for the critical heat flux of sprays and circular jets. Dependence of the heat transfer performance on spray mass flux and droplet diameter represents the influence of the overall heat transfer capacity of the spray as well as the contribution of droplet interactions. The Leidenfrost temperature of the spray was also shown to be dependent on the spray Weber number.     

超疏水聚合物表面的水滴蒸发模拟

基于质量守恒和Fick第一定律，模拟了水滴在超疏水聚合物表面的蒸发全过程．研究从以往的接触角<90±扩展到>150±，液滴形貌扩展为椭球球帽模型进行疏水表面蒸发模拟．水滴在超疏水PC和FPU/PMMA表面蒸发的实验结果显示，计算的椭球球帽模型可以更好的反映出液滴接触角和高度的变化情况，并且不同聚合物表面接触角的相同变化趋势也揭示出微-纳二级结构表面结构不仅影响液滴接触角，也影响液滴蒸发模式．     

液滴撞击壁面铺展及换热过程数值模拟

基于喷雾冷却时液滴撞击壁面现象,本文采用CLSVOF(coupled level set and volume of fluid)方法对不同工况下单液滴撞壁过程进行数值模拟,获得了单液滴撞击热壁面动态特性;分析了初始速度、液滴直径等初始参数对液滴撞壁后的动态铺展规律以及壁面换热特性的影响规律,获得了上述参数变化时液滴铺展系数和热流密度的变化趋势;探讨了场协同效应、液滴内部气泡以及三线接触点对壁面换热的影响。碰壁现象的研究对于大型制冷机组室外机散热、高热流电子器件散热等领域优化与控制喷雾有重要意义。     

Drop impact on superheated surfaces

At the impact of a liquid droplet on a smooth surface heated above the liquid's boiling point, the droplet either immediately boils when it contacts the surface ("contact boiling"), or without any surface contact forms a Leidenfrost vapor layer towards the hot surface and bounces back ("gentle film boiling"), or both forms the Leidenfrost layer and ejects tiny droplets upward ("spraying film boiling"). We experimentally determine conditions under which impact behaviors in each regime can be realized. We show that the dimensionless maximum spreading γ of impacting droplets on the heated surfaces in both gentle and spraying film boiling regimes shows a universal scaling with the Weber number We (γ~We(2/5)), which is much steeper than for the impact on nonheated (hydrophilic or hydrophobic) surfaces (γ~We(1/4)). We also interferometrically measure the vapor thickness under the droplet.