飞秒钛宝石激光脉冲的载波包络相移测量研究

飞秒激光脉冲的载波包络相移测量与控制是实现阿秒脉冲与光学原子钟的重要内容，在利用光子晶体光纤扩展飞秒钛宝石激光振荡器光谱的研究基础上，通过自参考技术测量并优化了该激光输出脉冲的载波包络相移所引起的拍频信号.实验上采用半导体抽运的倍频Nd:YVO4532nm激光器作为抽运源，对钛宝石激光器所产生的平均功率500mW、脉宽18fs的光脉冲进行拍频测量后观察到约23MHz的频移，对应于每周期053π的载波包络相移.飞秒激光脉冲载波包络相移测量的实现对于进一步利用电子反馈系统精确控制载波包络相移，从而得到高稳定的飞秒激光频率梳具有重要意义. 关键词： 载波包络相移 光子晶体光纤 飞秒 超连续     

面向Li原子D1线频率测量应用的掺铒飞秒光纤光梳系统

报道了自主研制的面向Li原子D1线频率测量应用的掺铒飞秒光纤光学频率梳,包括飞秒激光源,频率探测及控制单元,光谱展宽及拍频单元.光纤光梳系统中飞秒激光光源是一套基于非线性偏振旋转锁模机制的掺铒飞秒光纤激光器,重复频率为196.5MHz,中心波长为1 572nm.利用f-2f法探测载波包络相移频率,获得信噪比约为40dB的信号(分辨率带宽300kHz).改变飞秒激光光源泵浦控制载波包络相移频率、频率稳定度是3.74×10-18/τ1/2;通过电光晶体和压电陶瓷改变飞秒激光光源腔长来控制重复频率frep、频率稳定度是1.75×10-13/τ1/2.利用高非线性光纤和倍频晶体将光纤光梳直接输出光谱由1 520～1 607nm扩展到671nm,获得了单模功率为208nW的光信号.与671nm单频激光拍频产生约为60dB(分辨率带宽1Hz)信号,满足Li原子D1线频率测量实验的需求.     

飞秒钛宝石光学频率梳的精密锁定

经相位锁定后的飞秒钛宝石光学频率梳已经广泛用于绝对光频的测量，这是光频标领域一个革命性的突破.在自建的90MHz飞秒钛宝石激光器的基础上首先采用光子晶体光纤将其光谱展宽到一个光倍频程，接着利用锁相环技术分别将重复频率和载波包络频移同时高精度地锁定到一台稳定度为6×10^－14的Cs钟上，进而得到了稳定度相同的飞秒光学频率梳.     

利用锁相环和TV-Rb钟控制飞秒激光脉冲的载波包络相移

为了实现对锁模飞秒钛宝石激光器的相位控制，采用改进的相移测量装置，使载波包络频移信号的信噪比提高到了40 dB以上.在此优化测量结果的基础上，利用电子锁相环技术，通过PZT改变激光器腔内端镜的倾斜将飞秒激光脉冲的载波包络相位锁定到了微波参考源TV-Rb钟10 MHz标准信号上，同时激光脉冲重复频率也采用另一个PZT控制激光腔长锁定到了同一个TV-Rb钟10 MHz信号上.锁定后的结果显示重复频率的锁定达到了TV-Rb钟本身的稳定度，而载波包络相位锁定后比锁定前稳定度提高了三个数量级.     

覆盖可见光波长的掺Er光纤飞秒光学频率梳

飞秒光学频率梳波长覆盖范围向可见光波长扩展对于碘稳频激光的绝对频率测量以及光钟研究中钟激光的绝对频率测量都具有十分重要的意义. 本文在自行研制掺Er光纤飞秒光学频率梳的基础上, 采用放大-倍频-扩谱的方案, 实现了激光输出波长向可见光波长的扩展. 掺Er光纤飞秒光学频率梳输出的一部分光激光脉冲, 功率约为8 mW, 首先经掺Er光纤放大器将功率提高到531 mW, 此后利用MgO: PPLN晶体倍频, 倍频后激光的功率为170 mW, 倍频效率为32%, 脉冲宽度为85 fs. 倍频后的激光通过光子晶体光纤进行光谱展宽. 通过优化入射光偏振状态可以实现波长覆盖500-1000 nm, 输出功率为85 mW, 耦合效率为50%. 采用小型化碘稳频532 nm Nd: YAG激光器输出激光与光学频率梳光谱展宽后的激光进行拍频可以获得30 dB的拍频信号. 覆盖可见光波长的掺Er光纤飞秒光学频率梳为可见光范围内激光的绝对频率测量提供了技术手段.     

掺Er光纤飞秒激光器中电光晶体对激光器参数的影响

由于受增益介质上能级寿命的影响,掺Er光纤光梳的梳齿线宽一般在百kHz量级.为了实现光梳梳齿线宽的压窄,一种有效的方法是在激光器中增加快速响应的电光晶体,使光纤光梳的伺服锁定带宽提高到百kHz以上,为光纤光梳的快速伺服锁定提供反馈机构.这其中,高品质的飞秒激光器是核心.基于此,本文主要研究了掺Er光纤飞秒激光器中电光晶体对激光器参数的影响.通过计算电光晶体的折射率、色散、相位延迟等参数,分析了电光晶体对激光器参数的影响,并在实验上获得了电光晶体电压对激光器重复频率和载波包络偏移频率的影响,进而通过电光晶体实现了对光纤光梳重复频率和载波包络偏移频率的锁定.通过锁定光纤飞秒激光器与窄线宽激光器的拍频信号,验证了电光晶体的引入使激光器的伺服锁定带宽提高到了236 kHz,为窄线宽飞秒光学频率梳的建立提供了技术基础.     

双光路测量红外飞秒激光脉冲的载波包络相位稳定性

描述了利用双光路自参考技术测量红外飞秒脉冲载波包络相移的方法,并通过建立的红外飞秒脉冲载波包络相移测量装置,实验测量了自主搭建的可调谐光学参量放大系统输出的红外飞秒激光脉冲的载波包络相移.对于1.6 μm的激光脉冲,测量得到在100 s内其相位抖动为115 mrad（rms）.实验结果表明双光路法具有易于调节、测量方便、应用性强等优点. 关键词： 飞秒激光测量 自参考技术 双光路 载波包络相位     

掺镱硼酸钙氧钇飞秒激光器及在拉锥光纤中产生跨倍频程超连续光

跨倍频程超连续光谱的产生是光学频率梳系统中测量载波包络相移频率的关键.本文采用拉锥单模光纤作为非线性光谱展宽介质, 将半导体激光(LD)抽运的掺镱硼酸钙氧钇(Yb:YCOB)振荡器输出的飞秒激光耦合到该拉锥光纤中, 通过飞秒激光在光纤中发生的相位调制、四波混频等非线性效应将光谱展宽至超过倍频程的范围.振荡器输出的飞秒激光脉冲宽度为130 fs, 中心波长为1052 nm, 重复频率为76.8 MHz, 平均功率为620 mW, 耦合进单模拉锥光纤后获得了光谱覆盖范围从550 nm至1350 nm的跨倍频程超连续光谱, 最大输出平均功率为323 mW, 耦合效率达到52%.为进一步实现全固态飞秒激光光学频率梳提供了重要基础.     

用于光腔衰荡光谱测量的多支路掺铒光纤飞秒光梳系统

报道了用于光腔衰荡光谱测量的多支路掺铒光纤飞秒光梳系统.该系统以“9”字型全保偏掺铒飞秒光纤激光器为激光源.利用自制的锁相环电路,获得的重复频率和载波包络相移频率秒级稳定度分别为5.85×10^–13和4.95×10^–18.为了满足CO, CH₄等分子吸收光谱测量,利用啁啾放大和非线性光谱展宽技术,采用多支路结构,将飞秒光梳直接输出光谱由1500—1600 nm分别扩展至8个目标波长(1064, 1083, 1240, 1380, 1500,1600, 1750和2100 nm)处,各目标波长处的单模功率均大于300 n W,满足光腔衰荡光谱测量实验的需求.     

光纤飞秒光学频率梳的研制及绝对光学频率测量

实验利用商品光纤飞秒激光器,自行构建了一套完整的光学频率梳系统,并获得了约30 dB信噪比的系统频移(f_ceo)信号.实现了光频梳重复频率(f_rep)信号及系统频移(f_ceo)信号的高稳定度锁定,并通过实验验证了光频梳锁定的跟踪精度.基于此稳定光频梳完成了对1064 nm碘稳频Nd:YAG固体激光器的绝对频率测量.实验结果表明,f_rep的跟踪精度在100 s取样时间时优于3.7×10^-14,测量得到的1064 nm激光器绝对频率为:281630111757362 Hz.这一测量结果与国际计量委员会(CIPM)给出的国际推荐值符合到不确定度之内. 关键词： 光纤光频梳 稳频 锁相技术 光学频率计量     

White-light frequency comb generation with a diode-pumped Cr:LiSAF laser

We have created a broad spectrum spanning more than an optical octave by launching femtosecond pulses from a battery operated Cr:LiSAF laser into a photonic crystal fiber. Despite the massive broadening in the fiber, the comb structure of the spectrum is preserved, and this frequency comb is perfectly suited for applications in optical frequency metrology.     

Diode-pumped Yb:KYW femtosecond laser frequency comb with stabilized carrier-envelope offset frequency

We describe the detection and stabilization of the carrier envelope offset (CEO) frequency of a diode-pumped Yb:KYW (ytterbium-doped potassium yttrium tungstate) femtosecond oscillator that is spectrally centered at 1033 nm. The system consists of a diode-pumped, passively mode-locked femtosecond laser that produces 290 fs pulses at a repetition rate of 160 MHz. These pulses are first amplified, spectrally broadened and temporally compressed to 80 fs, and then launched into microstructured fiber to produce an octave-spanning spectrum. An f-2f nonlinear interferometer is employed with the broadened spectrum to detect and stabilize the CEO frequency through feedback to the pump laser current. These results demonstrate that such a Yb-doped tungstate laser can provide an efficient, compact, high-repetition-rate optical frequency comb with coverage from 650–1450 nm.     

掺Er光纤飞秒激光器载波包络位相偏移的探测

本文介绍了基于掺Er光纤飞秒激光器光学频率梳中光学部分的研制. 实验上采用重复频率为230 MHz的掺Er光纤飞秒激光器,通过放大、光谱展宽以及单臂f—2f系统,在优化及分析相关参数影响的基础上,获得了~30 dB信噪比f₀的输出,为光纤光学频率梳的建立奠定了基础. 关键词： 掺Er光纤激光器 光学频率计量 光纤光学频率梳 光谱展宽     

All-fiber Yb:fiber frequency comb

We demonstrate an all-fiber Yb:fiber frequency comb with a nonlinear-amplifying-loop-mirror-based Yb:fiber laser oscillator. The fiber-spliced hollow-core photonic bandgap fiber was used as dispersion compensator, which was also directly spliced to a piece of tapered photonic crystal fiber for an octave-spanning spectrum. The spectrum of the compressed 107 fs laser pulses was broadened, covering 600 nm to 1300 nm in a high-nonlinearity tapered fiber for f to 2 f beating. The signal-to-noise ratio of offset frequency was measured to be 22 dB.     

Tuning the frequency of ultrashort laser pulses by a cross-phase-modulation-induced shift in a photonic crystal fiber

Femtosecond pulses of fundamental Cr:forsterite laser radiation are used as a pump field to tune the frequency of copropagating second-harmonic pulses of the same laser through cross-phase modulation in a photonic crystal fiber. Sub-100-kW femtosecond pump pulses coupled into a photonic crystal fiber with an appropriate dispersion profile can shift the central frequency of the probe field by more than 100 nm, suggesting a convenient way to control propagation and spectral transformations of ultrashort laser pulses.     

飞秒激光在光子晶体光纤中产生超连续光谱机制的实验研究

报道了利用零色散在780nm处的光子晶体光纤与纳焦耳量级的飞秒激光脉冲相互作用的实验结果.实验使用35fs，中心波长810—840nm，单脉冲能量可达14nJ的飞秒激光光源获得了超过一个倍频程的平坦超连续光谱（500—1100nm）.在不同功率、不同中心波长、不同啁啾和有无直流成分的多种飞秒脉冲激光的条件下，研究了超连续光谱的产生情况.并对一系列现象进行了对比，分析了超连续光谱产生的机制. 关键词： 光子晶体光纤 飞秒脉冲激光 超连续光谱     

Coherent and incoherent spectral broadening in a photonic crystal fiber

The coherence of the spectral broadening process is the key requisite for the application of supercontinua in frequency combs. We investigate the coherence of two subsequent supercontinuum pulses created in a photonic crystal fiber pumped by a femtosecond laser. We measure Young interference fringes from a Michelson-type interferometer at different wavelengths of the output spectrum and analyze their dependence on pump intensity and polarization. The visibility of these fringes is a direct measure of the coherence of the spectral broadening processes.     

Generation of few-cycle laser pulses by coherent synthesis based on a femtosecond Yb-doped fiber laser amplification system

We demonstrate a coherent synthesis system based on femtosecond Yb-doped fiber laser technology. The output pulse of the amplification system is divided into two replicas and seeded into photonic crystal fibers of two parallel branches for nonlinear pulse compression. Because of the different nonlinear dynamics in the photonic crystal fibers, the compressed pulses show different spectra, which can be spliced to form a broad coherent spectrum. The integrated timing jitter between the pulses of two branches is less than one tenth of an optical cycle.By coherently synthesizing pulses from these two branches, 8 fs few-cycle pulses are produced.