北极冰-水耦合系统中声波传播特性

利用固体和流体介质中波传播理论,导出了冰-水两层复合结构中导波频散方程。进一步,利用二分法对频散方程进行了数值求解,得到了ω-k频散曲线(ω与k分别为圆频率和波数),以及相速度和群速度频散曲线。结果表明:冰-水两层复合结构中导波由具有相同厚度水层和冰层中导波耦合而成,但与水层和冰层中导波频散曲线相比,复合结构中导波频散曲线除第1阶模式外,其余高阶模式均发生了很大变化。从原水层第1阶模式的截止频率开始,复合结构第2阶模式的相速度曲线被压低,各高阶(大于2阶)模式的相速度曲线出现一个跃变点,群速度曲线出现一个极大和一个极小值。水层越厚,复合结构各高阶模式的截止频率越低,相同频带内导波模式越丰富。水层厚度保持不变时,复合结构各阶模式的相速度和群速度曲线均随冰层厚度的增加而向低频方向移动。另外,还进一步分析了冰-水复合结构的导波波结构,发现第1阶导波模式的能量主要集中在冰层内和海表面附近,而2阶以上高阶导波模式的振动位移幅度随深度方向呈现周期性特征,并且模式阶数越高,振动越复杂。      

孔隙介质包裹的充液管道结构中导波传播特性

研究孔隙介质包裹的充液管道中纵向导波传播特性,分析孔隙介质参数对频散曲线的影响。建立了孔隙介质包裹充液管道的结构模型,利用孔隙介质弹性波动理论,建立对应的频散方程,数值模拟计算得到该模型的频散曲线和时域波形,并分析了孔隙介质参数以及管壁厚度对频散曲线的影响。结果表明孔隙介质的渗透率对于导波频散的影响较小,孔隙度的改变对时域波形的位移幅度影响较大。同时,导波存在衰减,且衰减随孔隙度增大而增大。所得结论为埋地管道无损检测方面提供一定理论参考。      

液态金属快堆主管道中超声导波传播特性研究

讨论了钠冷快堆(Sodium-cooled Fast Reactor,SFR)主管道的整体温度和内部液态金属钠流动速度的变化对管道导波传播特性的影响。推导了充液管道中导波频散方程的一般形式,并给出了管道内液态金属钠处于流动状态下的导波频散方程。采用数值计算方法获得了管内液态金属钠处于不同温度和不同流速时的导波纵向模式频散曲线和导波时域波形。结果表明,温度变化对基阶纵向模式的影响较小,但对高阶纵向模式的影响较大;液态钠流速增大会使导波频散曲线向高频轻微移动,但在实际检测中可以忽路管内液体流动速度的影响。通过对时域接收波形的模拟计算,进一步考察了液态金属钠的温度及流动速度变化对导波传播的影响,并通过对比不同模态的激发特点和不同频段的导波时域波形特点,结合导波频散曲线,给出了适用于SFR管道超声无损检测的导波模态和声源激发频段选择方案。      

超声在固体火箭发动机无损检测中的应用

在固体火箭发动机的研制中，无损检测技术非常重要。本文介绍了一些主要的超声检测方法及其应用。脉冲多次反射法用于检测固体火箭发动机壳体与衬层之间的粘结质量。特性参数和扫频超声法以多层介质理论为基础，用于检测固体火箭发动机的深层粘结质量。     

被孔隙介质约束的弹性杆中的导波*

为了研究导波在被孔隙介质约束的弹性杆结构中的传播规律,分析孔隙参数对导波传播特性的影响,本文建立了无限大孔隙介质包裹圆柱体的理论模型,利用孔隙介质弹性波动理论,分析了导波的频散曲线,以及圆柱半径和孔隙参数对于导波传播特性的影响。结果表明,在该结构中传播的纵向导波存在频散特性。内部圆柱半径的改变影响波导结构,从而影响导波传播。外部孔隙介质的渗透率对于导波频散的影响较小,孔隙度的改变影响孔隙介质体波波速,从而影响导波频散曲线的截止频率。同时,导波存在较小的衰减,且衰减随孔隙度增大而增大。这些结果对于后续开展无限大介质包裹弹性杆结构的超声无损评价提供了一定的理论参考。     

无限流体中孔隙介质圆柱周向导波的传播特性

为研究无限大流体约束的孔隙圆柱中周向导波的传播规律,分析孔隙参数对导波传播特性的影响,建立了无限流体中孔隙介质圆柱的理论模型,利用孔隙介质弹性波动理论,建立了周向导波频散方程,通过数值模拟计算得到无限流体中孔隙介质圆柱的频散曲线,探讨了圆柱半径和孔隙参数对导波传播特性的影响,并对导波的衰减特性进行了分析;通过数值计算,得到了周向导波的时域波形,讨论了孔隙参数对波形的影响.结果表明,孔隙介质圆柱半径的改变影响圆柱尺度,孔隙度的改变影响孔隙介质中体声波的波速,都对周向导波频散曲线产生一定的影响,所得到的频散曲线特征及衰减曲线与时域波形吻合.研究结果对开展无限流体中孔隙介质圆柱的超声无损评价提供了一定的理论参考.     

含孔隙分层半空间中瑞利波的传播特性研究

为了研究含孔隙介质分层半空间中瑞利波的传播规律,分析孔隙介质参数对瑞利波频散曲线的影响,本文进行了数值模拟研究。采用传递矩阵算法,计算了含孔隙分层半空间中一定频率范围内瑞利波所有模式的频散及激发强度曲线,并与均匀弹性固体分层半空间情况作了类比分析,在含孔隙覆盖层的两层模型和含低速孔隙夹层的三层模型下,详细研究了孔隙度、渗透率、层厚度等参数对瑞利波各模式的影响,发现孔隙度及层厚度的变化对频散曲线影响较大,而渗透率的变化对频散曲线影响较小。      

圆管超声导波频散与多模态特性研究*

超声导波检测技术作为一种新兴的无损检测技术广泛应用于圆管类结构。为选择合适于不同缺陷检测的导波模态,推导分析了圆管导波传播的运动方程和频散方程;利用数值计算的方法得到了超声导波在圆管中传播的频散曲线和各模态沿壁厚方向的位移分布图,分析得出各个模态对不同缺陷的敏感程度;以一种特定的圆管为例,建立圆管缺陷有限元模型,对不同类型圆管缺陷对导波传播特性的影响进行仿真计算。结果表明,纵向模态对周向缺陷比较敏感,而扭转模态则对轴向缺陷更敏感,仿真结果与理论分析结果相吻合,为圆管缺陷检测的超声导波模态选择提供了理论依据。     

圆管超声导波频散与多模态特性

超声导波检测技术作为一种新兴的无损检测技术广泛应用于圆管类结构。为选择合适于不同缺陷检测的导波模态,推导分析了圆管导波传播的运动方程和频散方程;利用数值计算的方法得到了超声导波在圆管中传播的频散曲线和各模态沿壁厚方向的位移分布图,分析得出各个模态对不同缺陷的敏感程度;以一种特定的圆管为例,建立圆管缺陷有限元模型,对不同类型圆管缺陷对导波传播特性的影响进行仿真计算。结果表明,纵向模态对周向缺陷比较敏感,而扭转模态则对轴向缺陷更敏感,仿真结果与理论分析结果相吻合,为圆管缺陷检测的超声导波模态选择提供了理论依据。     

分层固体板中导波的激发与频散特性

针对无限大弹性分层固体板,研究了结构中导波的频散和激发特性。首先使用传递矩阵法推导分层板模型中导波的频散方程,然后用二分法求取导波各模式的频散曲线,进而分析结构中导波的频散特性。结果表明:在速度递增或递减的分层板中,基阶模式和高阶模式的高频极限分别等于低速层的瑞利波速和横波波速。对于含低速夹层的分层板,所有模式的高频极限都等于低速层的横波速度。在导波激发特性方面,研究了在具有一定宽度的法向力源作用下的分层板中导波各模式在结构中的法向位移谱。发现在速度递增的分层板结构中基阶模式是主导模式,而对于速度递减和含低速夹层模型,主导模式在不同的频段范围内对应不同的导波模式。      

Elastic guided wave propagation in a periodic array of multi-layered piezoelectric plates with finite cross-sections

In this study, we present a model study of guided wave dispersion and resonance behavior of an array of piezoelectric plates with arbitrary cross-sections. The objective of this work is to analyze the influence of the geometry of an element of a 1D-array ultrasound transducer on generating multi-resonance frequency so as to increase the frequency bandwidth of the transducers. A semi-analytical finite-element (SAFE) method is used to model guided wave propagation in multi-layered 1D-array ultrasound transducers. Each element of the array is composed of LiNbO₃ piezoelectric material with rectangular or subdiced cross-section. Four-node bilinear finite-elements have been used to discretize the cross-section of the transducer. Dispersion curves showing the dependence of phase and group velocities on the frequency, and mode shapes of propagating modes were obtained for different geometry consurations. A parametric analysis was carried out to determine the effect of the aspect ratio, subdicing, inversion layer and matching layers on the vibrational behavior of 1D-array ultrasound transducers. It was found that the geometry with subdiced cross-section causes more vibration modes compared with the rectangular section. Modal analysis showed that the additional modes correspond to lateral modes of the piezoelectric subdiced section. In addition, some modes have strong normal displacements, which may influence the bandwidth and the pressure field in front of the transducer. In addition, the dispersion curves reveal strong coupling between waveguide modes due to the anisotropy of the piezoelectric crystal. The effect of the matching layers was to cluster extensional and flexural modes within a certain frequency range. Finally, inversion layer is found to have a minor effect on the dispersion curves. This analysis may provide a means to analyze and understand the dynamic response of 1D-array ultrasound transducers.     

Ultrasonic guided wave focusing by a generalized phased array

Ultrasonic guided wave focusing by a generalized phased array is studied based on dispersion curves in a multi-layered medium. The different phase of the guided waves with different frequency is added on the excitation signal on each element of the transducer array for focusing. This can be realized by designing a proper excitation pulse based on the dispersion curves of the guided waves for each of the transducer array elements. The numerical simulation results show that the guided waves with different modes, different frequency components, and from different elements of the transducer array can all be focused at the target and focusing is achieved.     

Optically nonlinear phonon-polariton modes in a three-layered structure

A theory is presented for the propagation of phonon-polariton modes arising when phonons are coupled to electromagnetic waves in multilayered structures. A multi-layered structure consists of a thin film surrounded symmetrically by a bounding media. Numerical calculations are given for s-polarized phonon-polariton modes in the case where the bounding media are assumed to be semi-infinite layers with nonlinear dielectric functions of ionic crystal type supporting optical phonon modes and the thin film is characterized by a Kerr-type nonlinear dielectric function. The phonon-polaritons were found to have distinct branches characteristic of optical phonons and showing features that are different from those of plasmon-polaritons [S. Baher, M.G. Cottam, Surf. Rev. Lett. 10 (2003) 13]. The parameters that modify the modes are the in-plane wave vector, the thickness of the film, the phonon frequency and the nonlinearity of each layer. It was found that by increasing the film thickness and nonlinearity coefficient, the curves move to the left and the number of the branches increases without changing the pattern of the curves.     

等离子体填充金属光子晶体慢波结构色散特性研究

等离子体填充慢波器件为高效率、高功率真空电子微波源的发展提供了新的途径, 但其仿真和理论都具有一定的难度. 本文将通过轮辐天线加载激励信号的方法引入到等离子体填充金属光子晶体慢波结构(SWS)的色散特性仿真分析中, 研究了慢波结构参数和等离子体密度对等离子体填充慢波结构色散特性的影响. 结果表明, 无等离子体填充时, 通过轮辐天线加载激励信号方式得到的色散特性与其他方法差别不大; 与已有结果对比表明, 该方法适用于等离子体填充慢波结构的分析. 为了减小轮辐天线对腔体谐振频率的影响, 需要适当减薄轮辐天线的厚度, 并尽可能缩短其与反射面之间的距离. 天线的厚度越大越能激励慢波场, 越小谐振模式越容易被激励; 慢波结构周期膜片外半径和厚度对色散特性影响不大, 周期长度和膜片内半径对色散特性影响较大; 频率和相速色散曲线随等离子体密度上升而整体向高频区移动; 等离子体填充对低频模点的影响要大于对高频模点的影响; 对于慢波器件, 需要选择高频模点工作模式, 以减少腔的尺寸并降低电子注的初速度.     

各向异性色散左手材料平面波导的导模特性(英文)

对芯层为左手材料而内外包层都是普通材料的非对称三层平面波导TE振荡模进行了分析.在考虑左手材料色散和各向异性的情况下,从Maxwell方程组出发,得到了TE振荡模的色散方程和功率流分布,并且画出了相应的色散曲线.我们找到了8个TE振荡模,而且包括基模.随着模阶数的增加,模色散曲线右移,功率流曲线下移.但是,随着波导厚度的增加,色散曲线左移,功率流曲线上移.此外,TE振荡模有反常色散特性和负的群速,这正揭示了左手材料的本质特性.     

各向异性色散左手材料平面波导的导模特性

对芯层为左手材料而内外包层都是普通材料的非对称三层平面波导TE振荡模进行了分析.在考虑左手材料色散和各向异性的情况下,从Maxwell方程组出发,得到了TE振荡模的色散方程和功率流分布,并且画出了相应的色散曲线.我们找到了8个TE振荡模,而且包括基模.随着模阶数的增加,模色散曲线右移,功率流曲线下移.但是,随着波导厚度的增加,色散曲线左移,功率流曲线上移.此外,TE振荡模有反常色散特性和负的群速,这正揭示了左手材料的本质特性.     

Wave motion and dispersion phenomena: veering, locking and strong coupling effects

The dispersion curves describe wave propagation in a structure, each branch representing a wave mode. As frequency varies the wavenumbers change and a number of dispersion phenomena may occur. This paper characterizes, analyzes, and quantifies these phenomena in general terms and illustrates them with examples. Two classes of phenomena occur. Weak coupling phenomena-veering and locking-arise when branches of the dispersion curves interact. These occur in the vicinity of the frequency at which, for undamped waveguides, the dispersion curves in the uncoupled waveguides would cross: if two dispersion curves (representing either propagating or evanescent waves) come close together as frequency increases then the curves either veer apart or lock together, forming a pair of attenuating oscillatory waves, which may later unlock into a pair of either propagating or evanescent waves. Which phenomenon occurs depends on the product of the gradients of the dispersion curves. The wave mode shapes which describe the deformation of the structure under the passage of a wave change rapidly around this critical frequency. These phenomena also occur in damped systems unless the levels of damping of the uncoupled waveguides are sufficiently different. Other phenomena can be attributed to strong coupling effects, where arbitrarily light stiffness or gyroscopic coupling changes the qualitative nature of the dispersion curves.     

Rayleigh wave and detection of low-velocity layers in a stratified half-space

The excitation and propagation of the guided waves in a stratified half-space and a Rayleigh wave exploration method in shallow engineering seismic exploration are studied in this paper. All the modes of the guided waves are calculated by the bisection method in the case where the low velocity layers are contained in a stratified half-space. Cases when the formation shear wave velocity gradually decreases from the top to the bottom layers are also studied. The dispersion curves obtained in actual Rayleigh wave exploration are usually noncontinual zigzag curves, but the dispersion curves given by the elastic theory for given modes of the guided waves are smooth and continual curves. In this paper, the mechanism of zigzag dispersion curves in Rayleigh wave exploration is investigated and analyzed thoroughly. The zigzag dispersion curves can give not only the possible positions of the low-velocity layers but also the other information on the formation structure (fractures, oil, gas, etc.). It is found that the zigzag dispersion curves of the Rayleigh wave are the result of the leap of the modes and the existence of low velocity layers in a stratified half-space. The effects of the compressional wave velocity, shear wave velocity, and density of each layer on zigzag dispersion curves and the relationship of the low velocity layers to zigzag dispersion curves are also investigated in detail. Finally, the exploration depth of the Rayleigh wave is discussed. The exploration depth of the Rayleigh wave is equal to the wavelength multiplied by a coefficient that is variable and usually given by the work experience and the formation properties of the local work area.     

Parametric Analysis of Complex Dispersion Curves for Flexural Lamb Waves in Layered Plates in the Low-Frequency Range

A combined asymptotical and iteration method is used to study dispersion curves for the case of dynamic bending of isotropically layered plates. Based on the explicit limit formulation of dispersion equation, asymptotics of roots are derived in closed form for large values of root moduli. The influence of elastic and geometric parameters of layers are analyzed. The existence of critical values of geometric parameters that correspond to change of the type of asymptotics is demonstrated. The errors of asymptotics are estimated, and an iterative method is proposed for calculating the exact values of roots in statics. A low-frequency long-wave asymptotics of complex dispersion curves is derived; its accuracy is the higher the lower the frequency and the greater the number of the curve are. It is also proved that each complex curve has a long flat segment, the length of which increases simultaneously with the number of curve. The dispersion curves themselves are also calculated by another specific iterative procedure. The fundamental bending mode is analyzed together with its purely imaginary sister. The existence of the additional purely imaginary curve at low frequency is proved. Examples of calculating the static roots and the dispersion curves for subcritical and supercritical values of geometrical parameters are presented, and the efficiency of the algorithm is estimated.