45 nm MOSFET毫米波小信号等效电路模型参数提取技术

为了有效地表征45 nm MOSFET毫米波频段下的电学特性,研究了其高频等效电路的建模方法。基于45 nm MOSFET的器件物理结构及其导纳参数分析,通过综合考虑器件的本征物理特性、管脚及测试寄生特性,提出了一种准静态近似的高频等效电路模型及其参数直接提取的高精度简化算法,以此来统一表征模型参数从强反型区到弱反型区的偏置依赖性,并使之在不同偏置条件下的特性表征具有良好的连续性,以便于移植到商业仿真设计自动化工具中。通过ADS2013仿真工具的散射参数模拟结果与测量数据的一致性比较,验证了所建模型的实用性及其参数提取算法的准确性, 并表征了45 nm器件的偏置依赖性。     

FeCoBSiO2磁性纳米颗粒膜的微波电磁特性

采用交替沉积磁控溅射工艺制备了超薄多层的FeCoBSiO2磁性纳米颗粒膜.利用x射线衍射仪、扫描探针显微镜、透射电子显微镜分析了薄膜的微结构和形貌特征.采用振动样品磁强计、四探针法、微波矢量分析仪及谐振腔法测量薄膜试样的磁电性能和微波复磁导率.重点对SiO2介质相含量、薄膜微结构对电磁性能产生重要影响的机理做了分析和探讨.结果 表明：这类FeCoBSiO2磁性纳米颗粒膜具有良好的软磁性能和高频电磁性能，2GHz时的 磁导率μ′高于70，可以应用于高频微磁器件或微波吸收材料的设计. 关键词： 磁性纳米颗粒膜 高频特性 复磁导率 磁控溅射     

糖厂澄清工段生产指标建模及操作参数优化

针对亚法糖厂澄清工段清汁色值和清汁残硫量难以在线测量的问题,提出了一种基于人工蜂群优化的在线极限学习机软测量方法。先用核主元分析法确定影响清汁质量的关键参数,建立基于在线极限学习机的软测量模型。同时利用人工蜂群算法对在线极限学习机的隐层参数进行寻优,优化所建模型。最后,使用带约束的粒子群对软测量模型进行优化求解,得到典型工况下的最优操作设定值,为后续工况操作提供参考依据。仿真结果表明,基于人工蜂群优化的在线极限学习机模型能够准确地预测清汁色值和残硫量,同时基于此模型优化的操作参数设定值能够达到期望的指标。     

恒星大气物理参数估计中的稀疏特征提取

随着斯隆数字巡天项目(SDSS)、欧空局GAIA和我国大天区面积多目标光纤光谱天文望远镜(LAMOST)等项目的相继实施,拥有的恒星光谱数据量急速增加,由此导致基于光谱的恒星大气物理参数自动测量方法的研究成为天文光谱分析的重要课题之一[1]。探讨了恒星光谱特征提取的方法(Haar+lasso),其基本思想是首先使用Haar小波包对原始光谱进行多尺度分解,去除高频系数,选取低频系数作为光谱信息的描述;再采用lasso算法提取最优的特征; 最后将最优特征输入非参数回归模型中对恒星大气参数进行自动测量。Haar小波可以较好地去除原始光谱信号中的高频噪声,对全频谱数据进行降维。lasso算法可以进一步剔除数据冗余, 提取与物理参数相关度较强的特征。Haar+lasso方法提高了物理参数自动测量的准确性和运行效率。我们采用本文方案对SLOAN发布的40 000个恒星子样本的物理参数进行测量,三个物理参数的平均绝对误差为： log Teff: 0.007 1 dex,log g: 0.225 2 dex和[Fe/H]: 0.199 6 dex。同现有相关文献的实验结果相比,该方案可以获得更准确的物理参数。     

FeCoB-SiO2磁性纳米颗粒膜的微波电磁特性

采用交替沉积磁控溅射工艺制备了超薄多层的FeCoB SiO2 磁性纳米颗粒膜 .利用x射线衍射仪、扫描探针显微镜、透射电子显微镜分析了薄膜的微结构和形貌特征 .采用振动样品磁强计、四探针法、微波矢量分析仪及谐振腔法测量薄膜试样的磁电性能和微波复磁导率 .重点对SiO2 介质相含量、薄膜微结构对电磁性能产生重要影响的机理做了分析和探讨 .结果表明 :这类FeCoB SiO2 磁性纳米颗粒膜具有良好的软磁性能和高频电磁性能 ,2GHz时的磁导率 μ′高于 70 ,可以应用于高频微磁器件或微波吸收材料的设计     

Kamers-Kronig关系在反射太赫兹时域光谱测量中的应用

太赫兹时域光谱技术是材料介电参数测量的重要方法,是材料研究、鉴别和分析的重要工具。太赫兹时域光谱技术是一种太赫兹频段的相干探测技术,可以同时获得太赫兹波的幅度和相位信息,通过透射测量、反射测量可获得材料的复透射率或复反射率来反演材料的电磁参数。在实际中,大多数被测材料太赫兹波无法穿透,或者不满足透射材料参数反演需要的弱吸收近似,因此反射测量更具应用价值。在已发表的研究结果中,研究人员仍普遍采用透射测量的方案,很少见使用反射测量方案获取材料参数。究其原因,在反射测量时,由于样品和参考板位置的放置误差很难消除,从而导致无法准确提取反射相位。将光学领域广泛使用的Kamers-Kronig关系应用于太赫兹时域光谱系统反射测量中,以解决反射测量中无法准确获得相位信息从而无法提取介电参数的问题。为了验证Kamers-Kronig关系的准确性,一方面,通过透射、反射方法分别测量硅材料的复透射率、复反射率并反演了其材料参数,两者的反演结果一致性较好。另一方面,利用同一组硅的反射测量数据分别用Kamers-Kronig关系和最大熵法对其材料参数进行反演,两种处理方法也可以实现相互印证,进一步确保了提取数据的可靠性。对Kamers-Kronig关系和最大熵方法所取得的结果进行了对比讨论,通过Kamers-Kriong关系和最大熵法获得的折射率、消光系数以及复介电参数结果一致性较好,且基于Kamers-Kriong反演了一种精神药物的吸收谱,与透射结果做了比对。结果表明,Kamers-Kronig关系非常适合提取材料光学参数和吸收谱,且相比最大熵法其普适性更强,甚至对于无法获取相位信息的非相干测量系统依然适用,但该方法需要整个频段的反射率幅度信息,对于没有测量的频率需要进行外推,对于反射率随频率变化不大的物质更加适用。该研究成果对于利用反射式太赫兹时域光谱系统获取材料太赫兹波段的光学参数提供了一种有效方法,可解决绝大数情况下反射测量参数提取问题,对太赫兹时域光谱技术的实际应用具有重要意义。     

利用感应电动势测量交流磁导率

介绍了一种利用放人介质前后线圈两端感应电动势的变化来测量交流磁导率的方法,并推导了计算公式.利用此种方法可以测量不同形状材料在不同频率下的交流磁导率.本文还利用该种测量方法测量了不锈钢棒和非晶薄带的交流磁导率,结果与文献报道相符.     

基于漫反射光谱的组织光学参数测量系统与方法研究

在体组织光学参数测量是生物医学光子学研究重点,不仅为人体成分无创检测、光学成像、光动力疗法等研究提供基础,并且可以快速获取人体光学参数变化,为临床诊断提供依据。研究了利用单一源探距离漫反射光谱在体测量光学参数的测量系统与反构方法。漫反射光谱测量系统由宽谱光源、高分辨光纤光谱仪及光纤探头组成,结构简单,测量方便,可准确快速测量样品漫反射光谱。在光纤探头几何形状基础上,研究了光纤收集及系统传递函数,在此基础上对反构算法进行了校正。光学参数反构算法中正向模型基于Monte Carlo以及神经网络方法,适用光学参数范围大,计算速度快;逆向算法采用主成分分析与非线性建模拟合相结合的方法,可抑制测量噪声影响。在测量系统及反构算法基础上,进行了组织仿体光学参数测量实验,结果表明,利用单一源探距离下漫反射谱,可以较为准确获取吸收系数以及约化散射系数,均方根误差分别达到4.58%以及7.92%。为保证系统测量准确性,测量波长范围应覆盖样品中所含吸收物质吸收峰范围。所研究的在体组织光学参数测量方法为人体成分无创检测及测量条件变化获取提供了基础。     

基于去离群点策略提高目标位姿测量精度

针对在单目视觉目标位姿测量过程中,特征点提取出现离群点的情况,提出一种基于去除离群点策略的位姿测量方法(ORPE).建立了以特征点误差极大极小为原则的最优化目标函数,通过确定特征点最大观测误差值边界,判定并去除离群点,由此可消除离群点误差对位姿测量的影响.仿真实验使用ORPE对1 m×1 m × 1 m的立方体目标进行位姿测量,验证了算法的正确性;使用ORPE测量Boeing飞机模型的位姿,平均姿态角误差2.07°,平均位移误差1.6%.通过和最小二乘测姿法(LSPE)结果对比分析可得ORPE法误差小于LSPE法误差.表明ORPE能有效去除离群点,同时提高佗姿测量精度.     

大尺寸纳米晶磁环的动态磁性能测量

 在感应型速调管调制器中使用了纳米晶磁性材料制作大尺寸磁环，使用伏安向量法对材料试样的磁性能进行测量，得到频率为20.03 kHz和50 kHz时的动态磁化曲线、磁导率、磁场损耗等参数。使用脉冲法对成型的大尺寸磁环动态磁性能进行测量，励磁方式和工作中完全一致，在测量脉冲脉宽3.5~4.0 μs，重复频率50 Hz，初次线圈均为1匝，外径220 mm，内径80 mm，高60 mm，截面积4 200 mm²时，得到磁环实际能够达到的伏秒数为0.007 V·s，此时所需的偏磁电流大小为8 A。     

Frequency characterization of thin soft magnetic material layers used in spiral inductors

The paper details the characterization of thin magnetic materials layers, particularly soft materials, with respect to their behaviour in frequency (from 10 MHz to 1 GHz). The proposed method is suitable for any soft but insulating magnetic material; Yttrium Iron Garnet (YIG) is used as an example. The principle is based on a comparison between simulations for different values of the permeability and measurement values versus frequency of planar inductor structures; an experimental validation is proposed as well. Thin magnetic material is first deposited on an alumina substrate using RF sputtering technique; a planar spiral winding of copper is then deposited on the magnetic material by the same technique. The effective permeability versus frequency is obtained by comparing two samples of spiral windings with and without magnetic material. Network analyser measurements on samples of various geometrical dimensions and of different thicknesses are necessary to determine the effective magnetic permeability; we have obtained a relative effective permeability of about 30 for seven turns spiral inductor of a 17 μm YIG film.     

Causality study and numerical response of the magnetic permeability as a function of the frequency of ferrites using Kramers-Kronig relations

In this paper, the numerical treatment of magnetic loss of NiZn, MnZn, Ni₂Y, and NiZnCu ferrite and their composites, by using Krameres-Kronig relations, is investigated. The complex magnetic permeability spectra for ferromagnetic materials have been studied. Due to the principle of causality and time independence in the relation between magnetic induction B and magnetic field H, the real and the imaginary part of the complex magnetic permeability are mutually dependent, and the correlation is given by the Krameres-Kronig equations. Through them, it is possible to measure the real component of the complex magnetic permeability, assuming the real component is given, and by the Hilbert transform, the imaginary part of the magnetic permeability can be calculated. Magnetic circuit model has been studied theoretically, focusing on the model's poles in the complex plane to verify the principle of causality and the temporary independence.     

The effect of gamma radiation on the stator insulation of rotating electrical machines

ABSTRACT

The paper examines the influence of γ radiation on the stability of the insulation characteristics of the stator winding of rotating electrical machines. The tested insulation characteristics are loss tangent angle, resistance, polarization factor, threshold voltage of partial discharge, breakdown voltage, coefficient of proportionality and lifetime exponent. The radiation dose was used as the γ radiation parameter. Different winding areas have been specifically tested in which a different impact is expected on technological winding production process. Tests were performed on a representative statistical sample under well-controlled laboratory conditions. The combined measurement uncertainty of the experimental procedure was about 5%.     

高浓度纤维增强材料介电特性计算方法

针对复合材料的微观结构非均匀和各向异性特点带来的数值方法计算慢、内存消耗大的问题,利用均匀化方法计算纤维增强复合材料的等效电磁参数.采用了纤维低体积添加比至高体积添加比的迭代方法,同时提出了一个描述材料微观结构的修正的特征长度,将现有的均匀化方法推广至非准静态(微波频段)条件下高纤维浓度情况.提出的修正的均匀化模型可直接用于反射系数、屏蔽效能等计算,其屏蔽效能与实际微观结构复合材料的数值仿真结果进行了对比,验证了提出的等效电磁参数计算公式的有效性和频率适用范围.     

磁电耦合超材料本构矩阵获取方法的研究

单负(仅介电常数或仅磁导率小于零)超材料以及由导线-开口谐振环组成的双负超材料本构参数的提取通常采用传统的S参数方法. 由于磁电耦合超材料存在交叉极化现象, 仅用介电常数和磁导率两个本构参数无法准确描述其电磁特性. 传统的S参数提取方法一开始就假定超材料仅具有介电常数和磁导率两个本构参数, 所以采用该方法提取磁电耦合超材料本构参数存在明显局限性. 将磁电耦合超材料中的电元件和磁元件分别等效为面电流和面磁流, 通过推导平均电通密度和磁通密度与外加电磁场的相互关系, 从理论上获取了磁电耦合超材料2×2 的本构参数矩阵, 确定了磁电耦合超材料这四个本构参数与磁元件的磁导率、电元件的介电常数、空间色散项和耦合系数之间的关系解析公式, 进而获得了折射率理论计算公式. 利用该折射率公式对折射率提取值进行了非线性拟合, 发现提取值和理论值之间的误差很小, 这个结果很好地验证了所给出的本构矩阵解析式和折射率公式的正确性. 根据拟合结果, 获得了磁电耦合超材料本构矩阵中四个电磁参数的频率响应曲线. 所提出的磁电耦合超材料本构矩阵参数获取方法将为研究磁电超材料中电元件和磁元件的耦合现象提供重要的理论参考.     

横向偏置场作用的非晶带巨磁阻抗效应理论

采用多畴结构模型,考虑非晶带具有180°畴壁的磁畴及其两面的偏置磁场方向的不同,根据自由能最小原理,Maxwell方程组及带阻尼项的Landau-Lifshitz方程,建立了非晶态合金带在横向偏置磁场作用下的巨磁阻抗效应的理论计算公式. 提出并采用四状态平均磁导率代替单畴模型获得的磁导率,得到了更符合实际的处于偏置场作用的阻抗随外磁场变化的理论结果. 关键词： 偏置磁场 四状态 多畴结构 巨磁阻抗     

M(H) shape reconstruction using magnetic spectroscopy

Knowledge about the magnetization behavior M(H) is crucial for the use of magnetic materials in engineering applications. To date many systems exist that are able to measure the magnetization behavior, e.g. VSM, VCM, MOKE. In addition to their huge costs, complex and space-consuming measurement setup, large amount of preparatory work and restricted surface measurements are handicaps which restrict their field of application. Furthermore, the influence of additional physical quantities such as temperature, strain or pressure can only be investigated with great efforts. These influences are, however, of major importance in the development of magnetic sensor systems that are based on the change in magnetic properties.In this paper, a new measurement principle based on a frequency mixing technique is introduced for investigation of the shape of the magnetization curve of soft non-hysteretic magnetic materials. Based on the Taylor expansion of the magnetization curve and the spectral investigation of the inductively detected signal, a mathematical model for the reconstruction of M(H) is proposed. The model is both numerically and experimentally verified. It is shown that the magnetization curve of a nanocrystalline soft magnetic material used in this study can be reconstructed very accurately and the influence of an additional parameter, i.e. strain, can be investigated in detail as well.     

A composite-structured-light 3D measurement method based on fringe parameter calibration

This paper proposes a novel method for reducing measurement error caused by spectrum overlapping in composite-structured-light 3D measurement systems. For a composite-structured-light 3D measurement system, spectrum overlapping causes parameters of each deformed phase-shifting fringe to change, and therefore leads to phase measurement errors. The proposed fringe parameter calibration method is based on the fact that variations in each deformed fringe's parameters are independent of height and reflectivity of the measured object. Three frames of composite grating are projected on the reference plane, and each carrier channel includes the information of three phase-shifting sinusoidal gratings used in Phase Measuring Profilometry (PMP). With the parameter calculation formulas of PMP, the parameters of fringes demodulated from the same carrier channel can be calculated, and therefore parameter relation coefficients between fringes demodulated from different carrier channels may be obtained. When an object is measured, these relation coefficients can be used to calibrate the parameters of the deformed phase-shifting fringes. A new 3D measurement mathematical model is established to reconstruct the shape of the object. Experimental data proved that the proposed method can effectively restrain the effect of spectrum overlapping and improve measurement accuracy by more than three times.     

三维电磁扩散场数值模拟及磁化效应的影响

采用矢量有限元法实现了三维电磁扩散场数值模拟,并成功将其应用在大地电磁的正演研究中.为灵活精确地拟合起伏地形和地下不规则构造,采用由不规则四面体单元组成的非结构化网格,可根据模型设计的需要调整网格的大小.引入了基于二次场理论,将解析的一次场从总场中扣除,直接计算二次场,使得误差仅局限于相对较小的二次场,以提高总场计算精度.常规的节点有限元法不满足电性分界面上法向电场不连续和无源区单元内电流密度无散,违反麦克斯韦方程组.为克服节点有限元法的弊端,使用矢量有限元法求解基于二次电场的偏微分方程.另外,在算法设计中,考虑了磁导率参数的变化,可以模拟磁导率不均匀的模型.通过与COMMEMI模型已发表的结果对比,证明了本文算法的正确性和精确性.为突显非结构网格优势,计算了椭球异常体模型和任意地形模型的MT响应,并详细讨论了地形和磁化效应对三维数值模拟结果的影响.     

Determination of the dynamical behaviour of biological materials during impact using a pendulum device

A pendulum device has been developed to measure contact force, displacement and displacement rate of an impactor during its impact on the sample. Displacement, classically measured by double integration of an accelerometer, was determined in an alternative way using a more accurate incremental optical encoder. The parameters of the Kuwabara-Kono contact force model for impact of spheres have been estimated using an optimization method, taking the experimentally measured displacement, displacement rate and contact force into account. The accuracy of the method was verified using a rubber ball. Contact force parameters for the Kuwabara-Kono model have been estimated with success for three biological materials, i.e., apples, tomatoes and potatoes. The variability in the parameter estimations for the biological materials was quite high and can be explained by geometric differences (radius of curvature) and by biological variation of mechanical tissue properties.