Effect of radiation-induced mean wavelength shift in optical fibers on the scale factor of interferometric fiber optic gyroscope at a wavelength of 1300 nm

In order to analyze the effect of wavelength-dependent radiation-induced attenuation (RIA) on the mean transmission wavelength in optical fiber and the scale factor of interferometric fiber optic gyroscopes (IFOGs), three types of polarization-maintaining (PM) fibers is tested by using a ⁶⁰Co γ -radiation source. The observed different mean wavelength shift (MWS) behaviors for different fibers are interpreted by color-center theory involving dose rate-dependent absorption bands in ultraviolet and visible range and total dose-dependent near infrared absorption bands. To evaluate the mean wavelength variation in fiber coil and the induced scale factor change for space-borne IFOG under low radiation dose in space environment, the influence of dose rate on the mean wavelength is investigated by testing four germanium (Ge) doped fibers and two germanium-phosphorus (Ge-P) codoped fibers irradiated at different dose rates. Experimental results indicate that the Ge-doped fibers show the least mean wavelength shift during irradiation and their mean wavelength of optical signal transmitting in fibers will shift to shorter wavelength in low-dose-rate radiation environment. Finally, the change in the scale factor of IFOG resulting from the mean wavelength shift is estimated and tested, and it is found that the significant radiation-induced scale factor variation must be considered during the design of space-borne IFOG.     

Effect of radiation-induced color centers absorption in optical fibers on fiber optic gyroscope for space application

The effects of color centers' absorption on fibers and interferometric fiber optical gyroscopes(IFOGs) are studied in the paper. The irradiation induced attenuation(RIA) spectra of three types of polarization-maintaining fibers(PMFs), i.e.,P-doped, Ge-doped, and pure silica, irradiated at 100 Gy and 1000 Gy are measured in a wavelength range from 1100 nm to1600 nm and decomposed according to the Gaussian model. The relationship of the color centers absorption intensity with radiation dose is investigated based on a power model. Furthermore, the effects of all color centers' absorption on RIA and mean wavelength shifts(MWS) at 1300 nm and 1550 nm are discussed respectively. Finally, the random walk coefficient(RWC) degradation induced from RIA and the scale factor error induced by MWS of the IFOG are simulated and tested at a wavelength of 1300 nm. This research will contribute to the applications of the fibers in radiation environments.     

Effect of radiation-induced mean wavelength shift in optical fibers on the scale factor of an interferometric fiber optic gyroscope at a wavelength of 1300 nm

In order to analyze the effect of wavelength-dependent radiation-induced attenuation (RIA) on the mean trans- mission wavelength in optical fiber and the scale factor of interferometric fiber optic gyroscopes (IFOGs), three types of polarization-maintaining (PM) fibers are tested by using a 60 Co γ-radiation source. The observed different mean wave- length shift (MWS) behaviors for different fibers are interpreted by color-center theory involving dose rate-dependent absorption bands in ultraviolet and visible ranges and total dose-dependent near-infrared absorption bands. To evaluate the mean wavelength variation in a fiber coil and the induced scale factor change for space-borne IFOGs under low radiation doses in a space environment, the influence of dose rate on the mean wavelength is investigated by testing four germanium (Ge) doped fibers and two germanium-phosphorus (Ge-P) codoped fibers irradiated at different dose rates. Experimental results indicate that the Ge-doped fibers show the least mean wavelength shift during irradiation and their mean wavelength of optical signal transmission in fibers will shift to a shorter wavelength in a low-dose-rate radiation environment. Finally, the change in the scale factor of IFOG resulting from the mean wavelength shift is estimated and tested, and it is found that the significant radiation-induced scale factor variation must be considered during the design of space-borne IFOGs.     

卫星用光纤陀螺中抗辐射光纤的研究

介绍了光纤陀螺空间应用的优势及影响因素，提出了研究抗辐射光纤的防辐射加固方案。通过实验，证明了光纤的辐照效应，并提出了抗辐射光纤制备中的技术参考。     

干涉式光纤陀螺中的Rayleigh散射研究

从光的干涉原理出发分析了Rayleigh背向散射对干涉式光纤陀螺性能的影响,得出了散射光强与光纤位置之间的关系式,绘制了散射光强与光纤中位置之间的关系曲线,得到了距离光纤的两个端点越远Rayleigh背向散射对光纤陀螺的性能影响越小的结论。研究结果对分析光纤陀螺的光路误差有一定的参考价值。     

光源偏振度对光纤陀螺零漂影响的研究

以Y波导集成光学调制器保偏型干涉式光纤陀螺作为研究对象,根据各光学元器件的参数建立了各器件的琼斯矩阵以及光路传输模型,在此基础上进行了光路偏振误差的理论分析。通过推导,得到了保偏型干涉式光纤陀螺的偏振误差表达式,并首次分析了光源偏振度对光纤陀螺零漂的影响。借助光源尾纤输出的光谱,对由0%~3%之间呈线性变化的偏振度以及对经实验测试的光源偏振度的实际值引起的偏振模式耦合误差的零漂值进行了仿真计算。结果表明,当光路中其它参数不变时,由光源偏振度变化引起的零漂值为0.001°/h,满足了高精度光纤陀螺的精度要求。     

Construction and characterization of interferometric fiber optic gyroscope (IFOG) with erbium doped fiber amplifier (EDFA)

Gyroscopes, which sense changes on absolute angular rate and are classified into Interferometric Fiber Optic Gyroscopes (IFOG), Ring Laser Gyroscopes (RLG) and Micro- Electro-Mechanical Systems (MEMS) Gyroscopes, are critical components of the navigation systems together with accelerometers. Being dominant over other types of gyroscopes in terms of performance and cost, IFOGs have widely been used in metrology and in particular defense/aerospace industry. This paper covers the design details of both optical and electronic components of IFOG prototype, the sensing mechanism of which is based on Sagnac Phase Shift, constructed in Optics Laboratory of National Metrology Institute of TURKEY as absolute angular rate sensor. In the prototype IFOG, open-loop configuration was applied, a single mode telecommunication optical fiber and an EDFA pumped by DFB laser emitting at 1549.0 nm were used as sensing coil and broadband source, respectively. The voltage data carrying Sagnac Phase Shift was extracted by a phase tracking circuit consisting of an active RC band pass filter, an amplifier with adjustable gain and an AD630 balanced modulator chip which was operated as lock-in. For the prototype IFOG, peak to peak noise of 8 (°/h) and bias stability of 1.57 (°/h) were attained respectively. Moreover the scale factor of 13.83 (°/h)/mV was derived with deviation of 0.73%.     

应用于光纤陀螺的收发一体模块研究

基于干涉型光纤陀螺的小型化和工程化设计要求,研究了一种新颖的收发一体模块,从对SLD光源进行建模入手,设计了小型化的光学系统。并用Zemax软件进行了仿真。这种收发模块采用全保偏技术,体积小,可靠性高,可以有效地抑制光源与耦合器的串音干扰。与应用较为广泛的混偏技术相比,可以避免温度变化、振动等原因对光纤陀螺系统精度的影响,从而提高光纤陀螺的整体性能。     

Optically compensated dual-polarization interferometric fiber-optic gyroscope

We first introduce optical compensation into the field of interferometric fiber-optic gyroscopes (IFOGs), using the opposite polarity of the disturbance between two orthogonal polarization states to suppress polarization-fluctuation-induced noise. A dual-polarized IFOG, in which the fast and slow axes of polarization-maintaining fiber work simultaneously, is implemented and tested. Interference signals of the two axes are added to achieve optical compensation. Experiments show that the IFOG's sensitivity is effectively enhanced in compensated output: all Allan variance indices are improved, among which bias instability is reduced from 0.335 and 0.227 deg/h(fast and slow axes output, respectively) to 0.061 deg/h.     

Fabrication and Gamma-Ray Irradiation Effect on Optical and Mechanical Properties of Germano-Silicate Glass Fibers with Inner Cladding of B and F Doped Silica Glasses

ABSTRACT

The effect of glass composition, pure silica glass, boron-doped and fluorine-doped silica glasses of inner cladding, in the germano-silicate glass core fibers on optical and mechanical properties upon the γ-ray irradiation was investigated. Enhanced radiation hardening at 1,550 nm was found in both the B- and F-doped fibers after the γ-ray irradiation with dose-rate of 1.25 kGy/h. The radiation-induced attenuation (RIA) was found to increase in the order of the B-doped fiber, the F-doped fiber, and the silica fiber. While no major influence on the refractive index of the fibers after the γ-ray irradiation was found, the residual stress was slightly changed.     

Low-loss coupling between two single-mode optical fibers with different mode-field diameters using a graded-index multimode optical fiber

We present a method for ultra-low-loss coupling between two single-mode optical fibers with different mode-field diameters using multimode interference in a graded-index multimode optical fiber. We perform a detailed analysis of the interference effects and show that the graded-index fiber can also be used as a beam expander or condenser. The results are important for devices in which optical fibers with different mode-field diameters are coupled in series, such as in ultra-short-pulse fiber ring lasers, or in optical fiber communication links.     

小型内窥镜干涉型光纤陀螺仪装配质量控制系统（英）

提出一种用于干涉型光纤陀螺仪(IFOG)装配质量控制的内窥镜系统设计及相关图像分析方法。同时采用1.0 mm与2.4 mm工业内窥镜系统采集IFOG内部图像与视频数据;并利用多自由度运动控制平台调节内窥镜工作姿态以保证图像的顺利采集。在此基础上,设计了基于db4小波基的图像增强方法,基于灰度共生矩阵的图像纹理特征估计方法以及图像几何形状特征的计算方法等,用以进行内窥镜图像的分析。通过上述系统与方法的应用,能够有效检测出IFOG产品在装配过程中出现的多余物颗粒、光纤断纤或异常胶粘等质量问题,有效提高了IFOG产品的装配质量。     

Bending-induced optical loss in random-hole optical fibers

We present the experimentally determined optical bend loss for random hole optical fibers in the spectral range 1520 to 1570 nm induced by wrapping the optical fiber around a fixed diameter mandrel. The optical losses are compared to those obtained for a single-mode fiber and a multimode fiber using the same bending procedures. The bending induced optical losses in the random hole optical fibers were several orders of magnitude lower than for the single-mode fiber and were about 1 order of magnitude lower than for the multimode fiber.     

Indoor coverage improvement of MB-OFDM UWB signals with radio over POF system

A radio over fiber system using the fluorinated based polymer multimode fibers (PMMF) is presented in this paper for the enhancement of the indoor coverage of the multiband orthogonal frequency division multiplexing ultra-wideband standard (MB-OFDM UWB) inside a building. A preliminary part related the cost analysis owing to glass and polymer multimode fiber deployment inside a fiber network is reported. The study of the physical properties of the polymer optical fibers (core diameter, numerical aperture, differential mode delays, modal bandwidth…) is firstly performed in order to effectively exhibit the potentialities and the robustness of such fibers to be used in a low cost radio over fiber system. The DMD measurements of four fluorinated based polymer optical fiber are reported. The designed system operates at 850 nm with commercial off the shelf (COTS) devices combined to the intensity modulation/direct detection technique. The opportunity of using polymer fibers and COTS components to improve the indoor coverage of the MB-OFDM UWB standard is so reported by the measurement of the Error Vector Magnitude or the Relative Constellation Error variation as a function of the system parameters (RF power, optical attenuation, fiber length…) as well as the compliance of the eye diagram with the mask testing. By the way, the transmission performance of both 200 and 480 Mbps signals is demonstrated over up to 200 m link length of polymer multimode fibers: transmission penalties are quantified by relative constellation error with values under the standard requirements. A comparative study with classical OM2 50 μm based glass multimode fiber having the same bandwidth/length product than the PMMF is done.     

Light Absorption Induced in Undoped-Silica-Core Panda-Type Birefringent Optical Fiber by Pulsed Action of Ionizing Radiation

The evolution of radiation-induced absorption (RIA) of light at λ = 1.55 μmis compared after pulsed action of ionizing radiation at different probe light power in an undoped-silica-core Panda-type birefringent optical fiber and in an isotropic optical fiber drawn from the same preform before embedding the stress-applying rods.High efficiency of RIA photobleaching by the probe light at λ = 1.55 μm is revealed in the birefringent fiber.     

Analysis of chromatic dispersion effect on coherent optical CPFSK system and performance improvement with the use of combinations of various optical fibers

The performance of a coherent optical continuous-phase frequency shift keying (CPFSK) system is evaluated theoretically including the combined effect of fiber chromatic dispersion, non-zero laser line width and receiver noises. The system limitations imposed by chromatic dispersion and laser phase noise are depicted. The system performance can be improved by shifting the zero-dispersion wavelength to the operating wavelength of the system and this shifting can be achieved efficiently by using a suitable combination of different types of optical fibers. Dispersion shifting characteristics are demonstrated using four kinds of fibers, namely: standard single-mode fiber (SMF), dispersion shifted fiber (DSF), dispersion compensated fiber (DCF) and large core fiber (LCF). The effect of dispersion shifting on the system performance is evaluated in terms of transmission distance and bit rate.     

A novel video opto-mechanical (VOM) device for studying the effect of stretching speed on the optical and structural properties of fibers

Using a novel video opto-mechanical (VOM) device, the effect of stretching speed on the optical and structural properties of polypropylene (PP) fibers during the dynamic stretching process is studied. The objective of the present study is to correlate the optical and mechanical properties of PP fibers with the speed of stretching using the multiple-beam Fizeau fringes system. The skeletonization of the multiple-beam Fizeau fringes are determined automatically by using one-dimension Fourier transform method. The stepper motor is adjusted in order to stretch the fibers continuously with constant and uniform speed until breaking of the fiber. The refractive indices, birefringence, transverse sectional area and the orientation function of PP fibers are studied as a function of the draw ratio at different speeds of stretching. An empirical formula is given to correlate the birefringence of PP fiber and both the draw ratio and the speed of stretching. Stretching process of PP with low speed (slow stretching) is recommended to overcome the necking deformation along the fiber. The VOM device could be used to measure the yield strain. The draw ratio-stretching speed superposition is discussed with some details. Microinterferograms are given for illustration.     

Gamma-radiation effects in pure-silica-core photonic crystal fiber

We investigated the steady state gamma-ray radiation response of pure-silica-core photonic crystal fibers(PSC-PCFs)under an accumulated dose of 500 Gy and a dose rate of 2.38 Gy/min. The radiation-induced attenuation(RIA) spectra in the near-infrared region from 800 nm to 1700 nm were obtained. We find that the RIA at 1550 nm is related with hydroxyl(OH-) absorption defects in addition to the identified self-trapped hole(STH) defects. Moreover, it is proposed and demonstrated that reduced OH-absorption defects can decrease the RIA at 1550 nm. The RIA at 1550 nm has effectively declined from 27.7 d B/km to 3.0 dB/km through fabrication improvement. Preliminary explanations based on the unique fabrication processes were given to interpret the RIA characteristics of PSC-PCFs. The results show that the PSC-PCFs,which offer great advantages over conventional fibers, are promising and applicable to fiber sensors in harsh environments.     

An innovation based random weighting estimation mechanism for denoising fiber optic gyro drift signal

In Interferometric Fiber Optic Gyroscope (IFOG), the diminution of random noise and drift error is a critical task. These errors degrade the performance of IFOG. In this paper, a modified adaptive Kalman gain correction (AKFG) algorithm is proposed to denoise IFOG signal. The covariance matrix of innovation sequence is estimated using weighted average window method in which the weights are randomly generated in the range [0, 1]. Innovation based random weighted estimation (IRWE)-AKFG is applied to denoise the IFOG drift signal. The Kalman gain is adaptively updated using the covariance matrix of innovation sequence. The proposed algorithm is applied for denoising IFOG signal under static and dynamic environment. Allan variance method is used to analyze and quantify the stochastic errors in IFOG sensor. The performance of the proposed algorithm is compared with Conventional Kalman filter (CKF) and the simulation results reveal that the proposed algorithm is an efficient algorithm for denoising the IFOG signal.