Organic acid assisted solid-state synthesis of Li1.2Ni0.16Co0.08Mn0.56O2 nanoparticles as lithium ion battery cathodes

Lithium-rich layered oxide Li_1.2Ni_0.16Co_0.08Mn_0.56O₂ can be referred as a crystalline mixture of Li₂MnO₃ and LiNi_0.4Co_0.2Mn_0.4O₂ at equal molar ratio. In the paper, the solid state reaction of M(AC)₂·4H₂O (M = Mn, Co and Ni) and LiOH·H₂O has been performed to obtain nanocrystalline Li_1.2Ni_0.16Co_0.08Mn_0.56O₂ using a small molecular organic acid (i.e., oxalic acid (OA), citric acid (CA) or tartaric acid (TA)) as additive. The introduction of organic acids can help to improve the layered structure and inhibit the particle growth of Li_1.2Ni_0.16Co_0.08Mn_0.56O₂, and the different organic acids exert distinct influences on the structural and electrochemical properties of Li_1.2Ni_0.16Co_0.08Mn_0.56O₂. In detail, the nanoparticles obtained in the presence of OA have the smallest average size of 50–150 nm, which correspondingly exhibit the highest initial discharge capacity of 267.52 mAh g⁻¹ at 0.1C and the best high-rate capability (e.g., 152.22 mAh g⁻¹, 5C) when applied as a lithium ion battery cathode. Furthermore, the active substance obtained from TA shows the best cycling stability and a discharge capacity of 202.42 mAh g⁻¹ can be retained after 50 cycles at 0.5C.     

Preparation of LiNi0.5Mn0.5O2 cathode materials by urea hydrolysis coprecipitation

Layered LiNi_0.5Mn_0.5O₂ has been successfully synthesized via urea hydrolysis coprecipitation method. Well-crystallized LiNi_0.5Mn_0.5O₂ was obtained after calcinations of coprecipitation precursors and lithium salts at 450 °C for 3 h and following 900 °C for 10 h in air. Both the precursors and LiNi_0.5Mn_0.5O₂ powders show an agglomerated secondary structure with crystalline particles inside. The quasi-spherical morphology of the precursors was maintained during the calcinations. The first charge and discharge capacities of as-prepared LiNi_0.5Mn_0.5O₂ were 200 and 165mAh/g respectively. The discharge capacity of about 160mAh/g was retained after 10cycles for as-prepared samples.     

CO2 adsorption on Cr(1 1 0) and Cr2O3(0 0 0 1)/Cr(1 1 0)

We attempt to correlate qualitatively the surface structure with the chemical activity for a metal surface, Cr(1 1 0), and one of its surface oxides, Cr₂O₃(0 0 0 1)/Cr(1 1 0). The kinetics and dynamics of CO₂ adsorption have been studied by low energy electron diffraction (LEED), Aug er electron spectroscopy (AES), and thermal desorption spectroscopy (TDS), as well as adsorption probability measurements conducted for impact energies of E_i = 0.1-1.1 eV and adsorption temperatures of T_s = 92-135 K. The Cr(1 1 0) surface is characterized by a square shaped LEED pattern, contamination free Cr AES, and a single dominant TDS peak (binding energy E_d = 33.3 kJ/mol, first order pre-exponential 1 × 10¹³ s⁻¹). The oxide exhibits a hexagonal shaped LEED pattern, Cr AES with an additional O-line, and two TDS peaks (E_d = 39.5 and 30.5 kJ/mol). The initial adsorption probability, S₀, is independent of T_s for both systems and decreases exponentially from 0.69 to 0.22 for Cr(1 1 0) with increasing E_i, with S₀ smaller by ∼0.15 for the surface oxide. The coverage dependence of the adsorption probability, S(Θ), at low E_i is approx. independent of coverage (Kisliuk-shape) and increases initially at large E_i with coverage (adsorbate-assisted adsorption). CO₂ physisorbs on both systems and the adsorption is non-activated and precursor mediated. Monte Carlo simulations (MCS) have been used to parameterize the beam scattering data. The coverage dependence of E_d has been obtained by means of a Redhead analysis of the TDS curves.     

Synthesis of Y2O3:(Li,Eu) films using phosphor powders coated with SiO2 nano particles

Y_1.9−xLi_0.1Eu_xO₃ (x=0.02, 0.05, 0.08, and 0.12) films were fabricated by spin-coating method. A colloidal silica suspension with Y_1.9−xLi_0.1Eu_xO₃ phosphor powder was exploited to obtain the highly stable and effective luminescent films onto the glass substrate. After heating as-prepared Y_1.9−xLi_0.1Eu_xO₃ films at 700 °C for 1 h, the phosphor films exhibit a high luminescent brightness as well as a strong adhesiveness on the glass substrate. The emission spectra of spin-coated and pulse-laser deposited Y_1.82Li_0.1Eu_0.08O₃ films were compared. The cathodoluminescence of the phosphor films was carried out at the anode voltage 1 kV.     

Preparation and magnetic properties of the conductive Co(1−x)NixFe2O4/polyaniline microsphere composites

Core-shell Co_(1−x)Ni_xFe₂O₄/polyaniline nanoparticles, where the core was Co_(1−x)Ni_xFe₂O₄ and the shell was polyaniline, were prepared by the combination of sol-gel process and in-situ polymerization methods. Nanoparticles were investigated by Fourier transform spectrometer, X-ray diffraction diffractometer, Scanning electron microscope, Differential thermal analysis and Superconductor quantum interference device. The results showed that the saturation magnetization of pure Co_(1−x)Ni_xFe₂O₄ nanoparticles were 57.57 emu/g, but Co_(1−x)Ni_xFe₂O₄/polyaniline composites were 37.36 emu/g. It was attributed to the lower content (15 wt%), smaller size and their uneven distribution of Co_(1−x)Ni_xFe₂O₄ nanoparticles in the final microsphere composites. Both Co_(1−x)Ni_xFe₂O₄ and PANI/Co_(1−x)Ni_xFe₂O₄ showed superparamagnetism.     

Electrical screening of ternary NiO-Mn2O3-Co3O4 composition spreads

The compositional optimization of infrared-transparent conducting oxides was performed using high throughput screening of combinatorial libraries. Complete ternary composition spreads of NiO-Mn₂O₃-Co₃O₄ alloys were deposited onto conducting Nb-doped SrTiO₃ substrates using the pulsed laser deposition technique. Resistance-temperature relations of each composition in the spread were determined using a custom-designed scanning probe. The binary NiCo₂O₄ oxide showed the lowest electrical resistivity of about 0.1 Ω cm but unacceptably large resistance-temperature dependence (3.5%/°C). Electrically conducting ternary alloys along the line Mn_0.45Ni_0.63Co_1.92O₄-Mn_0.60Ni_0.72Co_1.68O₄-Mn_0.69Ni_0.81Co_1.50O₄ exhibited much lower temperature sensitivity (of about 1.5%/°C) as well as electrical resistance comparable to that of NiCo₂O₄. From this screening we propose new compounds for the thin-film ITCO sensors.     

Formation and characterization of the Cu2O overlayer on Zn-terminated ZnO(0 0 0 1)

Low-energy electron diffraction, X-ray photoelectron spectroscopy and synchrotron-radiation-excited angle-resolved photoelectron spectroscopy have been used to characterize Cu-oxide overlayers on the Zn-terminated ZnO(0 0 0 1) surface. Deposition of Cu on the ZnO(0 0 0 1)-Zn surface results in the formation of Cu clusters with (1 1 1) top terraces. Oxidation of these clusters by annealing at 650 K in O₂ atmosphere (1.3 × 10⁻⁴ Pa) leads to an ordered Cu₂O overlayer with (1 1 1) orientation. Good crystallinity of the Cu₂O(1 1 1) overlayer is proved by energy dispersion of one of Cu₂O valence bands. The Cu₂O(1 1 1) film exhibits a strong p-type semiconducting nature with the valence band maximum (VBM) of 0.1 eV below the Fermi level. The VBM of ZnO at the Cu₂O(1 1 1)/ZnO(0 0 0 1)-Zn interface is estimated to be 2.4 eV, yielding the valence-band offset of 2.3 eV.     

Growth and characterization of Nd:Lu3ScxGa5 − xO12 series laser crystals

A new series Nd:Lu₃Sc_xGa_5 − xO₁₂ (x = 0.5, 0.8, 1, 1.2 and 1.5) laser crystals have been successfully grown by the optical floating zone method. Their absorption and luminescence spectra were measured at room temperature and spectral parameters were systemically calculated using Judd-Ofelt (JO) theory. The fluorescence τ_f lifetimes were experimentally measured and compared with the theoretical results. Diode-pumped continuous-wave (CW) laser performance at 1.06 μm with mixed crystals was demonstrated. The influence of different x values on laser performance and spectral parameters was also discussed. All the results show that Nd:Lu₃Sc_xGa_5 − xO₁₂ series crystals should be suitable for laser application.     

Adsorption of water on thin V2O3(0 0 0 1) films

V₂O₃(0 0 0 1) films have been grown epitaxially on Au(1 1 1) and W(1 1 0). Under typical UHV conditions these films are terminated by a layer of vanadyl groups as has been shown previously [A.-C. Dupuis, M. Abu Haija, B. Richter, H. Kuhlenbeck, H.-J. Freund, V₂O₃(0 0 0 1) on Au(1 1 1) and W(1 1 0): growth, termination and electronic structure, Surf. Sci. 539 (2003) 99]. Electron irradiation may remove the oxygen atoms of this layer. H₂O adsorption on the vanadyl terminated surface and on the reduced surface has been studied with thermal desorption spectroscopy (TDS), vibrational spectroscopy (IRAS) and electron spectroscopy (XPS) using light from the BESSY II electron storage ring in Berlin. It is shown that water molecules interact only weakly with the vanadyl terminated surface: water is adsorbed molecularly and desorbs below room temperature. On the reduced surface water partially dissociates and forms a layer of hydroxyl groups which may be detected on the surface up to T ∼ 600 K. Below ∼330 K also co-adsorbed molecular water is detected. The water dissociation products desorb as molecular water which means that they recombine before desorption. No sign of surface re-oxidation could be detected after desorption, indicating that the dissociation products desorb completely.     

Low temperature adsorption of oxygen on reduced V2O3(0 0 0 1) surfaces

Well ordered V₂O₃(0 0 0 1) films were prepared on Au(1 1 1) and W(1 1 0) substrates. These films are terminated by a layer of vanadyl groups under typical UHV conditions. Reduction by electron bombardment may remove the oxygen atoms of the vanadyl layer, leading to a surface terminated by vanadium atoms. The interaction of oxygen with the reduced V₂O₃(0 0 0 1) surface has been studied in the temperature range from 80 to 610 K. Thermal desorption spectroscopy (TDS), infrared reflection absorption spectroscopy (IRAS), high resolution electron energy loss spectroscopy (HREELS), X-ray photoelectron spectroscopy (XPS), and density functional theory (DFT) were used to study the adsorbed oxygen species. Low temperature adsorption of oxygen on reduced V₂O₃(0 0 0 1) occurs both dissociatively and molecularly. At 90 K a negatively charged molecular oxygen species is observed. Upon annealing the adsorbed oxygen species dissociates, re-oxidizing the reduced surface by the formation of vanadyl species. Density functional theory was employed to calculate the structure and the vibrational frequencies of the O₂ species on the surface. Using both cluster and periodic models, the surface species could be identified as η²-peroxo () lying flat on surface, bonded to the surface vanadium atoms. Although the O-O vibrational normal mode involves motions almost parallel to the surface, it can be detected by infrared spectroscopy because it is connected with a change of the dipole moment perpendicular to the surface.     

Epitaxial MoOx nanostructures on TiO2(1 1 0) obtained using thermal decomposition of Mo(CO)6

Stoichiometric and highly-defective TiO₂(1 1 0) surfaces (called as yellow and blue, respectively) were exposed to Mo(CO)₆ vapours in UHV and in a reactive O₂ atmosphere. In the case of yellow-TiO₂, an O₂ reactive atmosphere was necessary to obtain the Mo(CO)₆ decomposition at 450 °C with deposition of MoO_x nanostructures where, according to core level photoemission data, the Mo⁺⁴ state is predominant. In the case of blue-TiO₂ it was possible to obtain Mo deposition both in UHV and in an O₂ atmosphere. A high dose of Mo(CO)₆ in UHV on blue-TiO₂ allowed the deposition of a thick metallic Mo layer. An air treatment of this sample at 580 °C led to the elimination of Mo as MoO₃ and to the formation of a transformed layer of stoichiometry of Ti_(1−x)Mo_xO₂ (where x is close to 0.1) which, according to photoelectron diffraction data, can be described as a substitutional near-surface alloy, where Mo⁺⁴ ions are embedded into the titania lattice. This embedding procedure results in a stabilization of the Mo⁺⁴ ions, which are capable to survive to air exposure for a rather long period of time. After exposure of the blue-TiO₂(1 1 0) substrate to Mo(CO)₆ vapours at 450 °C in an O₂ atmosphere it was possible to obtain a MoO₂ epitaxial ultrathin layer, whose photoelectron diffraction data demonstrate that is pseudomorphic to the substrate.     

Novel approach to preparation of LiMn2O4 core/LiNixMn2−xO4 shell composite

Combining two methods, coating and doping, to modify spinel LiMn₂O₄, is a novel approach we used to synthesize active material. First we coated the LiMn₂O₄ particles with the nickel oxide particles by means of homogenous precipitation, and then the nickel oxide-coated LiMn₂O₄ was calcined at 750 °C to form a LiNi_xMn_2−xO₄ shell on the surface of spinel LiMn₂O₄ particles. Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), cyclic voltammetry (CV) and charge-discharge test were performed to characterize the spinel LiMn₂O₄ before and after modification. The experimental results indicated that a spinel LiMn₂O₄ core is surrounded by a LiNi_xMn_2−xO₄ shell. The resulting composite showed excellent electrochemical cycling performance with an average fading rate of 0.014% per cycle. This improved cycle stability is greatly attributed to the suppression of Jahn-Teller distortion on the surface of spinel LiMn₂O₄ particles during cycling.     

Adsorption and dissociation of O2 on the Cu2O(1 1 1) surface: Thermochemistry, reaction barrier

The adsorption and dissociation of O₂ on the perfect and oxygen-deficient Cu₂O(1 1 1) surface have been systematically studied using periodic density functional calculations. Different kinds of possible modes of atomic O and molecular O₂ adsorbed on the Cu₂O(1 1 1) surface are identified: atomic O is found to prefer threefold 3Cu site on the perfect surface and O_vacancy site on the deficient surface, respectively. Cu_CUS is the most advantageous site with molecularly adsorbed O₂ lying flatly over singly coordinate Cu_CUS-Cu_CSA bridge on the perfect surface. O₂ adsorbed dissociatively on the deficient surface, which is the main dissociation pathway of O₂, and a small quantity of molecularly adsorbed O₂ has been obtained. Further, possible dissociation pathways of molecularly adsorbed O₂ on the Cu₂O(1 1 1) surface are explored, the reaction energies and relevant barriers show that a small quantity of molecularly adsorbed O₂ dissociation into two O atoms on the deficient surface is favorable both thermodynamically and kinetically in comparison with the dissociation of O₂ on the perfect surface. The calculated results suggest that the presence of oxygen vacancy exhibits a strong chemical reactivity towards the dissociation of O₂ and can obviously improve the catalytic activity of Cu₂O, which is in agreement with the experimental observation.     

Conductivity and sintering property of LaNi1 − xFexO3 ceramics prepared by Pechini method

Preparation of LaNi_1 − xFe_xO₃, which is one of the candidate materials of solid oxide fuel cell cathode, current collecting layer and interconnect coating was examined with Pechini method and solid state reaction method. Single phase LaNi_1 − xFe_xO₃ with large Ni content has successfully been prepared by low temperature sintering as 750 °C with Pechini method, whereas large amount of raw materials has remained with solid state reaction method by sintering at the same temperature. It can be ascribed to more homogenous cation distribution in raw powder material prior to sintering with Pechini method. It has also been revealed that LaNi_1 − xFe_xO₃ with x lower than 0.3 is thermodynamically unstable in air above 1000 °C. LaNi_0.6Fe_0.4O₃ showed superior property as cathode material with high electrical conductivity, thermodynamic stability and appropriate sintering property.     

Comparison of magnetic properties in LixCoO2 and its decomposition products LiCo2O4 and Co3O4

Thermal stability of cathode material in the charged state is an important aspect for the safety of rechargeable batteries. It is well known that layered Li_xCoO₂ decomposes to a mixture of LiCoO₂ and Co₃O₄ at elevated temperatures. However, not many experimental evidences exist on intermediate phases those may form during the decomposition. Using magnetic measurements we show that it is possible to distinguish between the spinels LiCo₂O₄ and Co₃O₄ and thereby follow the decomposition of Li_xCoO₂. We characterize the magnetic behavior of thermally aged Li_xCoO₂ (x = 0.98, 0.76, 0.55) with increasing annealing time. Our results reveal the appearance of magnetic ordering in the thermally degraded products. The detailed analysis illustrates that the formation of Co₃O₄ is preceded by the formation of a meta stable LiCo₂O₄ phase.     

Density functional theory calculations of surface properties and H2 adsorption on the Cu2O (1 1 1) surface

First-principles calculation on the basis of the density functional theory (DFT) and generalized gradient approximation have been applied to study the adsorption of H₂ on the stoichiometric O-terminated Cu₂O (1 1 1), Cu₂O (1 1 1)-Cu_CUS and Cu-terminated Cu₂O (1 1 1) surfaces. The optimal adsorption position and orientation of H₂ on the stoichiometric O-terminated Cu₂O (1 1 1) surface and Cu-terminated Cu₂O (1 1 1) surface were determined and electronic structural changes upon adsorption were investigated by calculating the Local Density of States (LDOS) of the Cu_CUS 3d and Cu_CUS 4s of stoichiometric O-terminated Cu₂O (1 1 1) surface. These results showed that H₂ molecule adsorption on Cu_CUS site parallel to stoichiometric O-terminated Cu₂O (1 1 1) surface and H₂ molecule adsorption on Cu₂ site parallel to Cu-terminated Cu₂O (1 1 1) surface were the most favored, respectively. The presence of surface copper vacancy has a little influence on the structures when H₂ molecule adsorbs on Cu_CSA, O_CUS and O_CSA atoms and the H₂ molecule is only very weakly bound to the Cu₂O (1 1 1)-Cu_CUS surface. From the analysis of stoichiometric O-terminated Cu₂O (1 1 1) Local Density of States, it is observed that Cu_CUS 3d orbital has moved to a lower energy and the sharp band of Cu_CUS 4s is delocalized when compared to that before H₂ molecule adsorption, and overlapped substantially with bands due to adsorbed H₂ molecule. The Mulliken charges of H₂ adsorption on Cu_CUS site showed that H₂ molecule obtained electron from Cu_CUS which was consistent with the calculated electronic structural changes upon H₂ adsorption.     

Adsorption and dissociation of H2 on the Cu2O(1 1 1) surface: A density functional theory study

Interactions of atomic and molecular hydrogen with perfect and deficient Cu₂O(1 1 1) surfaces have been investigated by density functional theory. Different kinds of possible modes of H and H₂ adsorbed on the Cu₂O(1 1 1) surface and possible dissociation pathways were examined. The calculated results indicate that O_SUF, Cu_CUS and O_vacancy sites are the adsorption active centers for H adsorbed on the Cu₂O(1 1 1) surface, and for H₂ adsorption over perfect surface, Cu_CUS site is the most advantageous position with the side-on type of H₂. For H₂ adsorption over deficient surface, two adsorption models of H₂, H₂ adsorbing perpendicularly over O_vacancy site and H₂ lying flatly over singly-coordinate Cu-Cu short bridge, are typical of non-energy-barrier dissociative adsorption leading to one atomic H completely inserted into the crystal lattice and the other bounded to Cu_CUS atom, suggesting that the dissociative adsorption of H₂ is the main dissociation pathway of H₂ on the Cu₂O(1 1 1) surface. Our calculation result is consistent with that of the experimental observation. Therefore, Cu₂O(1 1 1) surface with oxygen vacancy exhibits a strong chemical reactivity towards the dissociation of H₂.     

Electrochemical behavior of Li intercalation processes into a Li[NixLi(1/3−2x/3)Mn(2/3−x/3)]O2 cathode

Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ (X=0.17, 0.25, 0.33, 0.5) compounds are prepared by a simple combustion method. The Rietvelt analysis shows that these compounds could be classified as having the α-NaFeO₂ structure. The initial charge-discharge and irreversible capacity increases with the decrease of x in Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂. Indeed, Li[Ni_0.50Mn_0.50]O₂ compound shows relatively low initial discharge capacity of 200 mAh/g and large capacity loss during cycling, with Li[Ni_0.17Li_0.22Mn_0.61]O₂ and Li[Ni_0.25Li_0.17Mn₀.₅₈]O₂ compounds exhibit high initial discharge capacity over 245 mAh/g and stable cycle performance in the voltage range of 4.8 -2.0 V. On the other hand, XANES analysis shows that the oxidation state of Ni ion reversibly changes between Ni²⁺ and about Ni³⁺, while the oxidation state of Mn ion sustains Mn⁴⁺ during charge-discharge process. This result does not agree with the previously reported ‘electrochemistry model’ of Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂, in which Ni ion changes between Ni²⁺ and NI⁴⁺. Based on these results, we modified oxidation-state change of Mn and Ni ion during charge-discharge process.     

Growth of Al2O3 thin films on NiAl(1 0 0) by gas-phase oxidation and electro-oxidation

The growth and structures of aluminum oxides on NiAl(1 0 0) have been investigated by RHEED (reflection high energy electron diffraction), complemented by LEED (low energy electron diffraction), AES (Auger electron spectroscopy) and STM (scanning tunneling microscopy). Crystalline θ-Al₂O₃ phase grows through gas-phase oxidation on the NiAl(1 0 0) substrate with its a and b-axes parallel to [0 −1 0] and [0 0 1] direction of the substrate, respectively, forming a (2 × 1) unit cell. Whilst, three-dimensional nano-sized NiAl(1 0 0) protrusions and Al₂O₃, NiAl(0 1 1) clusters were found to co-exit at the surface, evidenced by extraordinary transmission spots superposed to the substrate reflection rods in the RHEED patterns. Particularly, the NiAl(0 1 1) clusters develop with their (0 1 1) plane parallel to the NiAl(1 0 0) surface, and [1 0 0] axis parallel to the [0 −1 1] direction of the substrate surface. STM observation combined with information from AES and TPD (temperature programmed desorption) suggest the formation of these 3D structures is closely associated with partial decomposition of the crystalline oxides during annealing. On the other hand, smoother (2 × 1) oxide islands with thickness close to a complete monolayer of θ-Al₂O₃ can be formed on NiAl(1 0 0) by electro-oxidation, in contrast with the large crystalline films formed by gas-oxidation.     

Scanning tunneling microscopy study of growth of Pt nanoclusters on thin film Al2O3/NiAl(1 0 0)

The growth of Pt nanoclusters on thin film Al₂O₃ grown on NiAl(1 0 0) was studied by using scanning tunneling microscopy (STM). The samples were prepared by vapor depositing various amounts of Pt onto the Al₂O₃/NiAl(1 0 0) at different substrate temperatures in ultra high vacuum (UHV). The STM images show that sizeable Pt nanoclusters grow solely on crystalline Al₂O₃ surface. These Pt clusters appear to be randomly distributed and only a few form evident alignment patterns, contrasting with Co clusters that are highly aligned on the crystalline Al₂O₃. The size distributions of these Pt clusters are rather broader than those of the Co clusters on the same surface and the sizes are evidently smaller. With increasing coverage or deposition temperature, the number of larger clusters is enhanced, while the size of the majority number of the clusters remains around the same (0.4 nm as height and 2.25 nm as diameter), which differs drastically from the Pt clusters on γ-Al₂O₃/NiAl(1 1 0) observed earlier. These Pt cluster growth features are mostly attributed to smaller diffusion length and ease to form stable nucleus, arising from strong Pt-Pt and Pt-oxide interactions and the peculiar protrusion structures on the ordered Al₂O₃/NiAl(1 0 0). The thermal stability of Pt nanoclusters was also examined. The cluster density decreased monotonically with annealing temperature up to 1000 K at the expense of smaller clusters but coalescence is not observed.