Magnetic,structural and electrical properties of ordered and disordered Co50Fe50 films

Co₅₀Fe₅₀ films with thickness varying from 100 to 500 Å were deposited on a glass substrate by sputtering process, respectively. Two kinds of CoFe films were studied: one was the as-deposited film, and the other the annealed film. The annealing procedure was to keep the films at 400 °C for 5 h in a vacuum of 5×10⁻⁶ mbar. From the X-ray study, we find that the as-deposited film prefers the CoFe(1 1 0) orientation. Moreover, the body-centered cubic (bcc) CoFe(1 1 0) line is split into two peaks: one corresponding to the ordered body-centered tetragonal (bct) phase, and the other, the disordered bcc phase. After annealing, the peak intensity of the ordered bct phase becomes much stronger, while that of the disordered bcc phase disappears. The annealing has also caused the ordered CoFe(2 0 0) line to appear. When the amount of the ordered bct phase in Co₅₀Fe₅₀ is increased, the saturation magnetization (M_s) and coercivity (H_c) become larger, but the electrical resistivity (ρ) decreases. From the temperature coefficient of resistance (TCR) measurement, we learn that the bct grains in the CoFe film start to grow at temperature 82 °C.     

Surface morphology and luminescence characterization of β-FeSi2 thin films prepared by pulsed laser deposition

β-FeSi₂ thin films were prepared on Si (1 1 1) substrates by pulsed laser deposition (PLD) with a sintering FeSi₂ target and an electrolytic Fe target. The thin films without micron-size droplets were prepared using the electrolytic Fe target; however, the surface without droplets was remarkably rougher using the Fe target than using the FeSi₂ target. After deposition at 600 °C and then annealing at 900 °C for 20 h, XRD indicated that the thin film prepared using the Fe target had a poly-axis-orientation, but that prepared using the FeSi₂ target had a one-axis-orientation. The PL spectra of the thin films prepared using the FeSi₂ and Fe targets at a growth temperature of 600 °C and subsequently annealed at 900 °C for 20 h had A-, B- and C-bands. Moreover, it was found that the main peak at 0.808 eV (A-band) in the PL spectrum of the thin films prepared using the FeSi₂ target was the intrinsic luminescence of β-FeSi₂ from the dependence of PL peak energy on temperature and excitation power density.     

Characteristic properties of Y2SiO5:Ce thin films grown with PLD

Three different gases (nitrogen (N₂), oxygen (O₂) and argon (Ar)) were used as background gases during the growth of pulsed laser deposition (PLD) Y₂SiO₅:Ce thin films. A Krypton fluoride laser (KrF), 248 nm was used for the PLD of the films on silicon (Si) (1 0 0) substrates. The effect of the background gases on the surface morphology, crystal growth and luminescent properties were investigated. All the experimental parameters, the gas pressure (455 mT), the substrate temperature (600 °C), the pulse frequency (8 Hz), the number of pulses (4000) and the laser fluence (1.6±0.2) J/cm² were kept constant. The only parameter that was changed during the deposition was the ambient gas species. The surface morphology and average particle sizes were monitored with scanning electron microscopy (SEM) and atomic force microscopy (AFM). X-ray diffraction (XRD) and Auger electron spectroscopy (AES) were used to determine the crystal structure and composition, respectively. Cathodo- (CL) and photoluminescence (PL) were used to measure the luminescent intensities for the different phosphor thin films. The nature of the particles, ablated on the substrate, is related to the collisions between the ejected particles and the ambient gas particles. The CL and PL intensities also depend on the particle sizes. A 144 h (coulomb dose of 1.4×10⁴ C cm⁻²) electron degradation study on the thin films ablated in the Ar gas environment resulted in a decrease in the main CL intensity peak at 440 nm and to the development of a new very broad luminescent peak spectra ranging from 400 to 850 nm due to the growth of a SiO₂ layer on the surface.     

Effect of post-annealing temperature on the microstructure and magnetic properties of Ce:YIG thin films deposited on Si substrates

Amorphous Ce₁Y₂Fe₅O₁₂ (Ce:YIG) thin films deposited on single crystal Si(1 0 0) and thermally oxidized Si(1 0 0) substrates by pulsed laser deposition were annealed in the temperature range of 700-1000 °C in air. The annealing temperature dependence of microstructure and magnetic properties of Ce:YIG films was studied using X-ray diffraction combined with vibrating sample magnetometer. The results show that single phase of polycrystalline Ce:YIG thin films can be obtained by the post-annealing of as-deposited films at the temperature of 700 °C. However, two steps of phase segregation of Ce:YIG occur as the post-annealing temperature increases: at first, Ce:YIG is decomposed into YIG and non-magnetic CeO₂ when annealed at 800 °C; then YIG continues to be decomposed forming Fe₂O₃ when the temperature is increased up to 900 °C. Consequently, the saturation magnetization of Ce:YIG films decreases first and then increases with the post-annealing temperature going up, which indicates that the saturation magnetization of Ce:YIG films is mainly related to the phase composition of the films. Meanwhile, the presence of SiO₂ buffer layer can significantly enhance the saturation magnetization of Ce:YIG films.     

Laser-excited spectra of Lu2SiO5:Ce scintillator

The emission spectra of Lu₂SiO₅:Ce single crystal under the excitation of 266 nm laser were investigated. The emission spectra of LSO single crystal show no temperature quenching from 20 to 300 K, under the excitation of 266 nm laser with 2 mJ pulse energy. With rising temperature, the Ce1 emission is slightly decreased, while the Ce2 emission is slightly increased. These results show the emissions of Ce1 and Ce2 is not only dependent on the concentration ratio but also influenced by the possible energy transfer processes, including Ce1 to Ce2, intrinsic STHs to Ce2 and the phonon-assisted transfer processes. The spectral thermal broadening and the spectral overlap become evident at high temperature, leading to the enhancement of energy transfer. When the excitation power lowers, the ratio of Ce1 and Ce2 emission increases, and is close to the Xe lamp ultraviolet (UV) excitation, suggesting that the energy transfer from Ce1 center to Ce2 center may be also dependent on the excitation power.     

Enhanced ferroelectric properties of (Pb0.90La0.10)Ti0.975O3 multilayered thin films prepared by RF magnetron sputtering

The (Pb_0.90La_0.10)Ti_0.975O₃/PbTiO₃ (PLT/PT), PbTiO₃/(Pb_0.90La_0.10)Ti_0.975O₃/PbTiO₃ (PT/PLT/PT) multilayered thin films with a PbO_x buffer layer were in situ deposited by RF magnetron sputtering at the substrate temperature of 600 °C. With this method, highly (1 0 0)-oriented PLT/PT and PT/PLT/PT multilayered thin films were obtained. The PbO_x buffer layer leads to the (1 0 0) orientation of the films. The dielectric, ferroelectric and pyroelectric properties of the PLT multilayered thin films were investigated. It is found that highly (1 0 0)-oriented PT/PLT/PT multilayered thin films possess higher remnant polarization 2P_r (44.1 μC/cm²) and better pyroelectric coefficient at room temperature p (p = 2.425 × 10⁻⁸ C/cm² K) than these of PLT and PLT/PT thin films. These results indicate that the design of the PT/PLT/PT multilayered thin films with a PbO_x buffer layer should be an effective way to enhance the dielectric, ferroelectric and pyroelectric properties. The mechanism of the enhanced ferroelectric properties was also discussed.     

Luminescence and energy transfer processes in Lu2SiO5:Ce scintillator

The energy transfer processes in Lu₂SiO₅:Ce³⁺ luminescence was investigated through the temperature dependent luminescence under excitation with VUV-UV. Ce1 center emission peaking at 393 and 422 nm and Ce2 center emission peaking at 462 nm were observed. Ce2 center emission is enhanced with the temperature, which can be explained by the rate of energy transfer from Ce1 center increases when the temperature rises. The Ce1 emission shows the thermal quenching effect under the direct excitation of Ce³⁺ at 262 nm. However, under the interband excitation of 183 nm, the Ce1 center emission exhibits undulating temperature dependence. This is because the emission is governed by thermal quenching and possible thermal enhancement of the transport of free carriers with the rising temperature.     

Crystallization-dependent magnetic properties of Mn1.56Co0.96Ni0.48O4 thin films

The effects of magnetic property dependence of the Mn_1.56Co_0.96Ni_0.48O₄ (MCN) films on crystallization are investigated in the growth temperature of 450-750 °C. With the growth temperature increase, both the crystalline quality and the grain size improve. The MCN films exhibit paramagnetic to ferromagnetic transition and the paramagnetic parts fit to the modified Curie-Weiss law. The ferromagnetic couplings of the magnetic ions in the MCN films enhance at elevated growth temperature. The saturation magnetization at 5 K increases with increasing growth temperature, but coercive field decreases monotonously. The magnetic properties of the MCN films strongly depend on their microstructures.     

The effects of substrate temperature on the structure, morphology and photoluminescence properties of pulsed laser deposited SrAl2O4:Eu,Dy thin films

In this study, SrAl₂O₄:Eu²⁺,Dy³⁺ thin film phosphors were deposited on Si (1 0 0) substrates using the pulsed laser deposition (PLD) technique. The films were deposited at different substrate temperatures in the range of 40-700 °C. The structure, morphology and topography of the films were determined by using X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM) and high resolution transmission electron microscopy (HRTEM). Photoluminescence (PL) data was collected in air at room temperature using a 325 nm He-Cd laser as an excitation source. The PL spectra of all the films were characterized by green phosphorescent photoluminescence at ∼530 nm. This emission was attributed to 4f⁶5d¹→4f⁷ transition of Eu²⁺. The highest PL intensity was observed from the films deposited at a substrate temperature of 400 °C. The effects of varying substrate temperature on the PL intensity were discussed.     

Enhanced luminescent characteristics of laser-ablated GdVO4:Eu thin films by Li-doping

Li-doping has been used to improve luminescent characteristics of thin films. Influence of Li-doping on the crystallization, surface morphology and luminescent properties of GdVO₄:Eu³⁺ films have been investigated. Crystallinity and surface morphology of thin films have been very important factors to determine luminescent characteristics and depended on the deposition conditions. The GdVO₄:Eu³⁺ and Li-doped GdVO₄:Eu³⁺ thin films have been grown using pulsed laser deposition method on Al₂O₃ (0 0 0 1) substrates at a substrate temperature of 600 °C under an oxygen pressure of 13.33-53.33 Pa. The crystallinity and surface morphology of the films were investigated using X-ray diffraction (XRD) and atomic force microscope (AFM), respectively. A broadband incoherent ultraviolet light source with a dominant excitation wavelength of 310 nm and a luminescence spectrometer have been used to measure photoluminescence spectra at room temperature. The emitted radiation was dominated by the red emission peak at 619 nm radiated from the transition of ⁵D₀-⁷F₂ of Eu³⁺ ions. Particularly, the peak intensity of Li-doped GdVO₄ films was increased by a factor of 1.7 in comparison with that of GdVO₄:Eu³⁺ films. The enhanced luminescence results not only from the improved crystallinity but also from the reduced internal reflections caused by rougher surfaces. The luminescent intensity and surface roughness exhibited similar behavior as a function of oxygen pressure.     

Dielectric relaxation in single crystal NH4H2PO4 in the high-temperature regime

The dispersion curves of the dielectric response in single crystal NH₄H₂PO₄ were obtained in the radio frequency range and below the high-temperature transition at T_p−160 °C. The results reveal dielectric relaxation at low frequency, which is about 10⁵ Hz at 70 °C, and it shifts to higher frequencies (∼3×10⁶ Hz) as the temperature increases. The relaxation frequency was determined from the peak obtained in the imaginary part of the permittivity as well as from the derivative of the real part of the permittivity. The activation energy E_a=0.55 eV, obtained from the relaxation frequency is very close to that derived from the dc conductivity. We suggest that this dielectric relaxation could be due to the proton jump and phosphate reorientation that cause distortion and change the local lattice polarizability inducing dipoles like      

The influence of substrate temperature variation on tungsten oxide thin film growth in an HFCVD system

Tungsten oxide (WO₃) thin films were deposited by a modified hot filament chemical vapor deposition (HFCVD) technique using Si (1 0 0) substrates. The substrate temperature was varied from room temperature to 430 °C at an interval of 100 °C. The influence of the substrate temperature on the structural and optical properties of the WO₃ films was studied. X-ray diffraction and Raman spectra show that as substrate temperature increases the film tends to crystallize from the amorphous state and the surface roughness decreases sharply after 230 °C as confirmed from AFM image analysis. Also from the X-ray analysis it is evident that the substrate orientation plays a key role in growth. There is a sharp peak for samples on Si substrate due to texturing. The film thickness also decreases as substrate temperature increases. UV-vis spectra show that as substrate temperature increases the film property changes from metallic to insulating behavior due to changing stoichiometry, which was confirmed by XPS analysis.     

A new Yb-doped oxyorthosilicate laser crystal: Yb:Gd2SiO5

A new Yb-doped oxyorthosilicate laser crystal, Yb:Gd₂SiO₅ (Yb:GSO), has been grown by the Czochralski (Cz) method. The crystal structure was determined by means of X-ray diffraction analysis. Room temperature absorption and fluorescence spectra of Yb³⁺ ions in GSO crystal were measured. Then, spectroscopic parameters of Yb:GSO were calculated and compared with those of another Yb-doped oxyorthosilicate crystal Yb:YSO. Results indicated that Yb:GSO crystal seemed to be a very promising laser gain media in generating ultra-pulses and tunable solid state laser applications. As expected, the output power of 2.72 W at 1089 nm was achieved in Yb:GSO crystal with absorbed power of only 4.22 W at 976 nm, corresponding to the slope efficiency of 71.2% through the preliminary laser experiment.     

Temperature dependent characteristics of La2O2S: Ln [Ln=Eu, Tb] with various Ln concentrations over 5-60 °C

This research is aimed at developing an optical sensor for remotely measuring human skin temperature in electromagnetically hostile environments, such as within a magnetic resonance imaging (MRI) scanner. In this feasibility study, various concentrations of europium-doped lanthanum oxysulphide (La₂O₂S: Eu—0.1-15 mol% (m/o)) and terbium-doped lanthanum oxysulphide (La₂O₂S: Tb—0.005-50 m/o) have been investigated in terms of crystallinity, photoluminescent (PL) spectral and decay time characteristics. For both phosphors, X-ray diffraction (XRD) has shown that as dopancy increases, the (1 0 0) and (0 0 2) reflections merge and there is a reduction in the c-axis parameter as well as the crystallite size. Photoluminescent characterisation (337 nm excitation) has also shown a dependency to dopant concentration through variance of peak intensity. Temperature dependent decay time measurements were carried out over a low temperature range 5-60 °C. Optimum brightness of these temperature dependent lines is achieved at concentrations of 1 and 10 m/o for La₂O₂S: Eu and La₂O₂S: Tb respectively. However, optimum temperature dependency is achieved at lower concentration for La₂O₂S: Eu, specifically at 0.1 m/o. In comparison to conventional phosphor temperature dependent characteristic, La₂O₂S: Tb showed an increase in decay time with respect to temperature for concentrations above 2 m/o.     

Formation of silicon nanodots from dysprosium-doped amorphous SiCxOy films grown by hot-filament assisted chemical vapor deposition of CH3SiH3 and Dy(DPM)3 gas jets

We report on Si nanodot formation by chemical vapor deposition (CVD) of ultrathin films and following oxidation. The film growth was carried out by hot-filament assisted CVD of CH₃SiH₃ and Dy(DPM)₃ gas jets at the substrate temperature of 600 °C. The transmission electron microscopy observation and X-ray photoelectron spectroscopy analysis indicated that ∼35 nm Dy-doped amorphous silicon oxycarbide (SiC_xO_y) films were grown on Si(1 0 0). The Dy concentration was 10-20% throughout the film. By further oxidation at 860 °C, the smooth amorphous film was changed to a rough structure composed of crystalline Si nanodots surrounded by heavily Dy-doped SiO₂.     

Luminescence properties of Ge implanted SiO2:Ge and GeO2:Ge films

We have investigated cathodeluminescence (CL) of Ge implanted SiO₂:Ge and GeO₂:Ge films. The GeO₂ films were grown by oxidation of Ge substrate at 550 °C for 3 h in O₂ gas flow. The GeO₂ films on Ge substrate and SiO₂ films on Si substrate were implanted with Ge-negative ions. The implanted Ge atom concentrations in the films were ranging from 0.1 to 6.0 at%. To produce Ge nanoparticles the SiO₂:Ge films were thermally annealed at various temperatures of 600-900 °C for 1 h in N₂ gas flow. An XPS analysis has shown that the implanted Ge atoms were partly oxidized. CL was observed at wavelengths around 400 nm from the GeO₂ films before and after Ge⁻-implantation as well as from SiO₂:Ge films. After Ge⁻-implantation of about 0.5 at% the CL intensity has increased by about four times. However, the CL intensity from the GeO₂:Ge films was several orders of magnitude smaller than the intensity from the 800 °C-annealed SiO₂:Ge films with 0.5 at% of Ge atomic concentration. These results suggested that the luminescence was generated due to oxidation of Ge nanoparticles in the SiO₂:Ge films.     

Luminescent characteristics of CaTiO3:Pr thin films prepared by pulsed laser deposition method with various substrates

CaTiO₃:Pr³⁺ films were deposited on different substrates such as Al₂O₃ (0 0 0 1), Si (1 0 0), MgO (1 0 0), and fused silica using pulsed laser deposition method. The crystallinity and surface morphology of these films were investigated by XRD and SEM measurements. The films grown on the different substrates have different crystallinity and morphology. The FWHM of (2 0 0) peak are 0.18, 0.25, 0.28, and 0.30 for Al₂O₃ (0 0 0 1), Si (1 0 0), MgO (1 0 0), and fused silica, respectively. The grain sizes of phosphors grown on different substrates were estimated by using Scherrer's formula and the maximum crystallite size observed for the thin film grown on Al₂O₃ (0 0 0 1). The room temperature PL spectra exhibit only the red emission peak at 613 nm radiated from the transition of (¹D₂ → ³H₄) and the maximum PL intensity for the films grown on the Al₂O₃ (0 0 0 1) is 1.1, 1.4, and 3.7 times higher than that of the CaTiO₃:Pr³⁺ films grown on MgO (1 0 0), Si (1 0 0), and fused Sillica substrates, respectively. The crystallinity, surface morphology and luminescence spectra of thin-film phosphors were highly dependent on substrates.     

Epitaxial growth of InN on nearly lattice-matched (Mn,Zn)Fe2O4

We have grown InN films on nearly lattice-matched (Mn,Zn)Fe₂O₄ (111) substrates at low temperatures by pulsed laser deposition (PLD) and investigated their structural properties. InN films grown at substrate temperatures above 400 °C show poor crystallinity, and their in-plane epitaxial relationship is [10-10]InN//[11-2](Mn,Zn)Fe₂O₄, which means that their lattice mismatch is quite large (11%). By contrast, high quality InN films with flat surfaces can be grown at growth temperatures lower than 150 °C with the ideal in-plane epitaxial relationship of [11-20]InN//[11-2](Mn,Zn)Fe₂O₄, which produces lattice mismatches of as low as 2.0%. X-ray reflectivity measurements have revealed that the thickness of the interfacial layer between the InN and the substrates is reduced from 14 to 8.4 nm when the growth temperature is decreased from 400 °C to room temperature. This suppression of the interface reactions by reducing the growth temperature is probably responsible for the improvement in crystalline quality. These results indicate that the use of (Mn,Zn)Fe₂O₄ (111) substrates at low growth temperatures allows us to achieve nearly lattice matched epitaxial growth of InN.     

Ferromagnetism at 300 K in spin-coated films of Co doped anatase and rutile-TiO2

Thin films of Ti_1−xCo_xO₂ (x=0 and 0.03) have been prepared on sapphire substrates by spin-on technique starting from metalorganic precursors. When heat treated in air at 550 and 700 °C, respectively, these films present pure anatase and rutile structures as shown both by X-ray diffraction and Raman spectroscopy. Optical absorption indicate a high degree of transparency in the visible region. Such films show a very small magnetic moment at 300 K. However, when the anatase and the rutile films are annealed in a vacuum of 1×10⁻⁵ Torr at 500 and 600 °C, respectively, the magnetic moment, at 300 K, is strongly enhanced reaching 0.36μ_B/Co for the anatase sample and 0.68μ_B/Co for the rutile one. The ferromagnetic Curie temperature of these samples is above 350 K.     

Influence of crystallization on the spectral features of nano-sized ferroelectric barium strontium titanate (Ba0.7Sr0.3Tio3) thin films

Ferroelectric barium strontium titanate (Ba_0.7Sr_0.3TiO₃)(BST) thin films have been prepared from barium 2-ethylhexanoate [Ba[CH₃(CH₂)₃CH(C₂H₅)CO₂]₂]_, strontium 2-ethylhexanoate [Sr[CH₃(CH₂)₃CH(C₂H₅)CO₂]₂] and titanium(IV) isopropoxide [TiOCH(CH₃)₂]₄ precursors using a modified sol-gel technique. The precursor except [TiOCH(CH₃)₂]₄ were synthesized in the laboratory. Transparent and crack-free films were fabricated on pre-cleaned quartz substrates by spin coating. The structural and optical properties of films annealed at different temperatures have been investigated. The as-fired films were found to be amorphous that crystallized to the tetragonal phase after annealing at 550 °C for 1 h in air. The lattice constants “a” and “c” were found to be 3.974 A and 3.990 A, respectively. The grain sizes of the films annealed at 450, 500 and 550 °C were found to be 30.8, 36.0 and 39.8 nm respectively. The amorphous film showed very high transparency (∼95%), which decreases slightly after crystallization (∼90%). The band gap and refractive index of the amorphous and crystalline films were estimated. The optical dispersion data are also analyzed in the light of the single oscillator model and are discussed.