飞秒BBO光参量放大中闲频光二次谐波的产生

由于相位匹配条件和非线性晶体透光范围的限制，400nm蓝光抽运的飞秒β-BaB₂O₄（BBO）光参量放大（OPA）输出的参量光调谐范围有限，很难得到波长小于460nm的蓝光和近紫外光.实验采用1kHz钛宝石九通啁啾脉冲放大器的倍频蓝光作抽运光，超连续白光 作种子光，在Ⅰ类非共线相位匹配条件下，利用宽带的飞秒BBO OPA，在一定的实验参数下 获得了530—810nm放大的信号光，以及810nm—17μm波段范围的闲频光.与此同时 ，还获得了410—700nm连续可调的闲频光的二次谐波，其与闲频光层叠分布，单脉冲能量 为26μJ，转换效率大于5%.仅利用单块晶体的飞秒BBO OPA就可以获得410—810nm连 续可调的飞秒脉冲输出，从而为更多研究和应用的需要提供了重要的光源.对飞秒光参量放 大中闲频光二次谐波产生的条件也进行了理论分析. 关键词： 二次谐波 闲频光 非共线相位匹配 飞秒光参量放大     

空间走离和相速度补偿的高效飞秒脉冲倍频

采用两块大小均为10 mm×10 mm×0.2 mm的BBO晶体级联的实验方案对中心波长为800 nm、脉宽70 fs、重复频率10 Hz的激光进行了倍频,针对BBO晶体的空间走离和相速度失配,分别调节两块倍频晶体的光轴夹角和基频光的角度匹配失谐量.实验表明,两块倍频晶体光轴反向平行可以补偿空间走离效应,一定的角度失谐可以补偿基频光和倍频光的相速度失配.在无聚焦情况下,使用两块BBO晶体级联相互配合优化将8.1 mJ的入射基频光倍频后得到带宽6.7 nm(傅里叶转换极限脉冲宽度为35 fs)、2.8 mJ以上的倍频光.其倍频效率高达35.7%,是同等条件下单块晶体倍频转换效牢的1.7倍.     

飞秒掺钛蓝宝石激光三倍频理论和实验研究

从理论和实验上分别研究了飞秒掺钛蓝宝石激光二倍频和三倍频的非线性频率转换过程.采 用Ⅰ类相位匹配非共线和频方法得到飞秒掺钛蓝宝石激光的三倍频2601nm输出，转换效 率达64%, 脉冲宽度为169fs.这为时间分辨电子显微镜提供了一种超短脉冲的紫外光源. 关键词： 飞秒激光 三倍频 时间分辨 BBO晶体     

全固态飞秒激光高光束质量三倍频研究(特邀)

对全固态飞秒激光三倍频产生高光束质量343 nm飞秒激光进行了系统研究。基频光源为脉冲宽度为105 fs、重复频率为76 MHz、中心波长为1 030 nm的商用Yb:KGW锁模激光器,利用1.7 mm长LBO晶体获得60%的二倍频转换效率,然后分别研究了基于BBO晶体Ⅱ类相位匹配和Ⅰ类相位匹配的三倍频产生。在基频光功率为5 W的条件下,利用Ⅱ类相位匹配的BBO晶体,获得的最大平均功率为0.71 W,三倍频转换效率约为14%;利用Ⅰ类相位匹配的BBO晶体,获得平均功率为1.01 W的紫外激光输出,三倍频转换效率为20.2%。获得的343 nm紫外激光的光束质量优于1.3。     

基于单晶体的可调谐参量超荧光的产生

研究了一种基于单晶体的可调谐超荧光产生机理，在一个偏硼酸钡(BBO)晶体中实现了飞秒脉冲倍频过程和光参量产生过程.实验中采用kHz高功率钛宝石激光系统输出的飞秒脉冲光倍频后的蓝光作为抽运光，获得了可调谐范围为480—530 nm参量超荧光光谱输出.理论上分析了这种超荧光产生机理，并利用放大传递函数模拟出参量超荧光环的产生过程.结果表明，在一个BBO晶体中，当抽运光源输出光入射晶体角度同时满足倍频相位匹配角和非共线光参量产生相位匹配角时可产生参量超荧光环，通过微调相位匹配角可控制参量超荧光光谱调谐输出.该理论和实验研究为控制参量超荧光和量子纠缠态的产生提供了理论依据，对于量子成像和量子通讯等领域的发展具有重要意义.     

BiB_3O_6纳秒光参变振荡器

采用电光调Q脉冲Nd:YAG固体激光器的532 nm绿光作为抽运光源(10～13 ns,0～20 mJ),以Ⅱ类相位匹配(θ=57.5°Φ=0°)、尺寸为4 mmX 4 mm×12 mm的三硼酸铋晶体(BiB3O6)与一对1215 nm单谐振波长的平镜组成腔长为40 mm的谐振腔,构建了光参变振荡器的整个实验系统.系统将入射抽运光振荡产生1215 nm的信号光及946 nm的闲频光,结果显示,抽运阈值为9 mJ,最高耦合输出为2.57 mJ,抽运脉冲能量与信号脉冲能量的最高转换效率为14.59%.     

飞秒激光泵浦Ⅰ类BBO晶体中自发参量下转换的研究

实验研究了飞秒脉冲激光泵浦Ⅰ类BBO晶体中自发参量下转换效应,以及产生的彩色锥形辐射现象.系统分析了各参量对二次谐波转换效率及彩色锥形辐射现象的影响.研究结果表明:蓝绿色锥形辐射具有最大的发散角,这与相位匹配理论模拟结果吻合;正入射时,增大泵浦光强及晶体厚度均会引起彩色锥形辐射亮度增加,且最大出射角中心波长往长波移动;...     

基于单个BBO晶体载波包络相位稳定的高效率光参量放大器

基于单个BBO非线性晶体,利用非共线光参量放大技术,研究了载波包络相位稳定的高效率可调谐近红外脉冲产生.以载波包络相位稳定的飞秒激光放大系统产生的白光作为种子光,注入一个二类匹配的二级光参量放大器,在1350 nm波段获得抽运-信号光34%的转换效率.利用f—2f光谱相干测量技术,放大脉冲载波包络相位的抖动30 min内小于137 mrad.该方法提供了一种简单高效的载波包络相位稳定的红外脉冲产生技术.     

利用群速度匹配的级联二阶非线性实现超短激光脉冲压缩

提出了一种采用倾斜脉冲的级联二阶非线性来实现超短激光脉冲压缩的方法. 对基于单块BBO晶体中基频光与倍频光群速度匹配的级联二阶非线性的脉冲压缩方案进行了理论分析. 对比研究了群速度匹配与失配情况下利用级联二阶非线性进行脉冲压缩的效果, 并模拟分析了基频光与倍频光的位相失配量、非线性晶体长度、 基频光初始峰值光强和初始脉宽等因素对脉冲压缩效果的影响. 结果表明, 基频光与倍频光的群速度匹配将会大幅度改善压缩脉冲的时间波形和频谱分布. 通过对位相失配量、晶体长度、初始光强等参数的优化和选取可获得较理想的压缩效果. 采用倾斜脉冲的级联二阶非线性的脉宽压缩方法, 针对中心波长800 nm、脉宽100 fs, 峰值光强为50 GW/cm²的基频光脉冲, 采用25 mm厚BBO晶体, 当基频光与倍频光位相失配量Δk=60 mm^-1(对应失谐角1.98°), 晶体外部脉冲前沿倾斜角γ₀=74°时, 计算获得了质量较好的20 fs剩余基频光, 并同时产生了14 fs的倍频光. 关键词： 倾斜波 级联二阶非线性 群速度失配 脉冲压缩     

飞秒激光泵浦I类BBO晶体中自发参量下转换的研究

实验研究了飞秒脉冲激光泵浦I类BBO晶体中自发参量下转换效应,以及产生的彩色锥形辐射现象.系统分析了各参量对二次谐波转换效率及彩色锥形辐射现象的影响.研究结果表明:蓝绿色锥形辐射具有最大的发散角,这与相位匹配理论模拟结果吻合|正入射时,增大泵浦光强及晶体厚度均会引起彩色锥形辐射亮度增加,且最大出射角中心波长往长波移动|不同光束偏振态下可依次观察到彩色锥形辐射、超连续现象.     

High-Efficiency Generation of 0.12 mJ,8.6 Fs Pulses at 400 nm Based on Spectral Broadening in Solid Thin Plates

We demonstrate efficient generation of continuous spectrum centered at 400 nm from solid thin plates. By frequency doubling of 0.8 mJ, 30 fs Ti:sapphire laser pulses with a BBO crystal, 0.2 mJ, 33 fs laser pulses at400 nm are generated. Focusing the 400-nm pulses into 7 thin fused silica plates, we obtain 0.15 mJ continuous spectrum covering 350-450 nm. After compressing by 3 pairs of chirped mirrors, 0.12 mJ, 8.6 fs pulses are achieved.To the best of our knowledge,this is the first time that sub-10-fs pulses centered at 400 nm are generated by solid thin plates, which shows that spectral broadening in solid-state materials works not only at 800 nm but also at different wavelengths.     

Sum and difference frequency generation of white light continuum with the ps pulses of Nd:YAG laser in a thick BBO crystal

The white light continuum (WLC) generated in water/D₂O mixture by pumping with the fundamental of ps Nd⁺³:YAG laser has been used as a variable frequency source for the sum frequency generation as well as for its amplification. 35 ps long pulses with 8 mJ energy at 1064 nm were mixed collinearly with the WLC generated by the same laser beam in a 20 mm thick BBO crystal. The obtained tunable output has been identified as the sum frequency between the fundamental and a portion of the WLC with the required phase matching. Theoretical simulations are also given along with a few initial experiments to use this combination for the difference frequency generation (optical parametric amplification) under non-collinear geometry.     

Prospects for increasing average power of optical parametric chirped pulse amplifiers via multi-beam pumping

We demonstrate optical parametric amplification of broadband chirped pulses in BBO crystal pumped by several intersecting beams extracted from independent laser amplifiers. The energy of amplified signal ranged from 0.23 to 0.72 mJ depending on a number of pump beams used as well as pumping configuration employed. The conversion efficiency dependence on intersection angles of pump beams is revealed and modeling of interplay of interacting waves is presented.     

在BBO中获得230.8—223.2nm高功率和频输出

用Q-YAG泵浦的Rh·6G染料激光在一块45°切割的β-BaB₂O₄(BBO)晶体中倍频,产生294.8—282.5nm范围的连续调谐输出,其能量为8mJ(在285nm处)。用这个倍频光与泵浦染料后剩余基波(1064nm)在另一块45°切割的BBO中和频,已获得230.8—223.2nm范围的连续调谐输出,其能量为120μJ,相应的峰值功率为12kW。还简述了获得高功率和频输出的关键技术。     

Few‐cycle,broadband, mid‐infrared optical parametric oscillator pumped by a 20‐fs Ti:sapphire laser

A few‐cycle, broadband, singly‐resonant optical parametric oscillator (OPO) for the mid‐infrared based on MgO‐doped periodically‐poled LiNbO₃ (MgO:PPLN), synchronously pumped by a 20‐fs Ti:sapphire laser is reported. By using crystal interaction lengths as short as 250 µm, and careful dispersion management of input pump pulses and the OPO resonator, near‐transform‐limited, few‐cycle idler pulses tunable across the mid‐infrared have been generated, with as few as 3.7 optical cycles at 2682 nm. The OPO can be continuously tuned over 2179‐3732 nm (4589‐2680 cm^‐1) by cavity delay tuning, providing up to 33 mW of output power at 3723 nm. The idler spectra exhibit stable broadband profiles with bandwidths spanning over 422 nm (FWHM) recorded at 3732 nm. The effect of crystal length on spectral bandwidth and pulse duration is investigated at a fixed wavelength, confirming near‐transform‐limited idler pulses for all grating interaction lengths. By locking the repetition frequency of the pump laser to a radio‐frequency reference, and without active stabilization of the OPO cavity length, an idler power stability better than 1.6% rms over >2.75 hours is obtained when operating at maximum output power, in excellent spatial beam quality with TEM₀₀ mode profile. Photograph shows a multigrating MgO:PPLN crystal used as a nonlinear gain medium in the few‐cycle femtosecond mid‐IR OPO. The visible light is the result of non‐phase‐matched sum‐frequency mixing between the interacting beams.     

Generation of UV radiation at 335.5 nm based on frequency-quadrupling of a diode-pumped Nd:YVO4 laser

The generation of ultraviolet （UV） light at 335.5 nm based on frequency quadrupling of a diode-end- pumped Q-switched Nd：YVO4 laser at 1342 nm was demonstrated. KTP crystal was used for generation of wavelength of 671 nm by intracavity doubling and LBO （BBO） crystal was exploited for the subsequent external fourth harmonic generation （FHG）. With 6.3-W absorbed pump power and 10-kHz frequency repetition rate, the UV output power of 35 and 63 mW were obtained by using LBO and BBO as frequency quadrupling nonlinear crystals, respectively. The experimental results show that the conversion efficiency （red-UV） of 6.4% for BBO crystal is higher than that of 3.5% for LBO crystal, but the UV beam quality obtained by LBO crystal is better than by BBO crystal.     

在BBO晶体中获得271—281.5nm和频输出

本文用自制的Q-YAG的倍频光泵浦Rh·6G染料,用调谐的染料激光束(562—598nm)与YAG的倍频光束在B-BaB2O4(BBO)晶体中和频,获得的连续可调谐范围是271-281.5nm,和频输出能量大子200μJ,最高转换效率为5%.我们用陈创天等人和K.Kato所给BB0晶体的Sellmetier方程计算了和频调谐曲线,它们之间的相位匹配角大约有一度之差.实验曲线与两条理论曲线都有不同程度的偏差.但是,与K.Kato的理论曲线更为接近.我们还讨论了BBO晶体的长度对输出能量的影响,并解释了产生这种影响的原因。     

Efficient generation of tunable VUV laser radiation below 205 nm by SFM in BBO

Design and performance characteristics of a tunable dye laser system for sum frequency mixing (SFM) in a BBO crystal are presented. The system is composed of two tunable pulsed dye lasers pumped synchronously by the second harmonic of a commercial Nd:YAG laser. The radiation produced by the first dye laser is frequency doubled by second-harmonic generation (SHG) in KDP and subsequently mixed by SFM in BBO with the light of the second dye laser. The interest was focussed on generation of tunable laser radiation below 205 nm with high output power and long-time wavelength stability. High conversion efficiencies enable output energies of 100 J (20 kW) at 196 nm using only moderate Nd:YAG pump energies of 67 mJ. Altogether, a laser system with very good specifications for analytical application in the near VUV spectral region is reported.     

飞秒激光在6H SiC晶体表面制备纳米微结构

激光诱导周期性纳米微结构在多种材料包括电介质、半导体、金属和聚合物中观察到。研究了800nm和400nm飞秒激光垂直聚焦于6H SiC晶体表面制备纳米微结构。实验观察到800nm和400nm线偏光照射样品表面分别得到周期为150nm和80nm的干涉条纹,800nm圆偏振激光单独照射样品表面得到粒径约100nm的纳米颗粒。偏振相互垂直的800nm和400nm激光同时照射晶体得到粒径约100nm的纳米颗粒阵列,该纳米阵列的方向随400nm激光强度增加而向400nm偏振方向偏转。利用二次谐波的观点对以上纳米结构的形成给出了解释。     

在BBO中产生217.3-2 21.4nm高功率和频输出

用Q-YAG激光的三次谐波(355nm)与调谐的Rh·6G染料激光在β-BaB2O4(BBO)晶体中和频,获得217.3～221.4nm连续调谐输出,和频输出的最大能量为250μJ,转换效率为11%.我们还讨论了获取最大和频输出能量的一些实验条件.