Long period gratings written into a photonic crystal fibre by a femtosecond laser as directional bend sensors

A series of symmetric and asymmetric LPGs were inscribed in photonic crystal fibre by a low repetition rate femtosecond laser system. The asymmetric LPGs were found to be spectrally sensitive to bend orientation, with some of the attenuation bands producing both red and blue wavelength shifts, whilst the symmetric devices produced only a unidirectional wavelength shift. Both sets of devices displayed strong polarisation dependence.     

Measured sensitivity of arc-induced long-period grating sensors in photonic crystal fibre

Reported are experimental results from investigations of the sensing properties of long-period gratings (LPGs) recorded in two different geometries of photonic crystal fibre (PCF): a large-mode area PCF and an endlessly single mode PCF. The LPGs have been characterised for their sensitivity to temperature, bending, surrounding index and strain. The LPGs in both fibres have been found to have negligible temperature sensitivity whilst exhibiting useful strain sensitivities. Strong directional bend sensitivity is shown by one PCF whilst the other shows good non-directional bend sensitivity. The fibres exhibit differing sensitivities to surrounding refractive index.     

High sensitivity long-period grating-based temperature monitoring using a wide wavelength range to 2.2 μm

Temperature effects on the various cladding modes of a long-period grating (LPG) fabricated in B-Ge co-doped fibre have been investigated to create a high sensitivity measurement device. The temperature sensitivities of the attenuation bands of the LPG over the wavelength region 1.2-2.2 μm, for a grating with a 330 μm period, were obtained by monitoring the wavelength shift of each attenuation band, with a temperature increment of 20 °C, over the range from 23 °C to 140 °C. The attenuation band appearing over the 1.8-2.0 μm wavelength range has shown a nearly five times higher temperature sensitivity than that of lower order modes, and thus it shows significant promise for fibre optic temperature sensor applications.     

Demonstration of fundamental mode only propagation in highly multimode fibre for high power EDFAs

The use of short lengths of large core phosphate glass fibre, doped with high concentrations of Er or Er:Yb represents an attractive route to achieving high power erbium doped fibre amplifiers (EDFAs) and lasers (EDFLs). With the aim of investigating the potential of achieving diffraction limited output from such large core fibres, we present experimental results of fundamental mode propagation through a 20 cm length of passive 300 μm core multimode fibre when the input is a well-aligned Gaussian beam. Through careful control of fibre geometry, input beam parameters and alignment, we measured an output M² of 1.1 ± 0.05. The fibre had a numerical aperture of 0.389, implying a V number of 236.8. To our knowledge, this is the largest core fibre through which diffraction limited fundamental mode propagation has been demonstrated. Although the results presented here relate to undoped fibre, they do provide the practical basis for a new generation of EDFAs and EDFLs.     

Estimation of the fibre temperature during the inscription of arc-induced long-period gratings

The underlying formation mechanisms and the properties of long-period gratings produced through arc discharges are intrinsically related to the temperature reached by the fibre during arc exposure. In this work, the determination of the fibre temperature was based on Plank’s blackbody radiation law. The radiation emitted by the optical fibre during heating due to an electric arc discharge, detected using a Cronin spectrometer, was fitted to the emission spectrum of the blackbody radiation, allowing the estimation of the temperature range attained by the fibre. A peak temperature of 1400 ± 50 °C was obtained.     

Broadband Er-Yb co-doped superfluorescent fiber source

In this paper, extensive experimental results on broad-band double cladding Er³⁺-Yb³⁺ co-doped superfluorescent fiber sources (SFSs), characterizing their output power, mean wavelength, and bandwidth (BW) stability with variations of pump power, pump wavelength, and fiber temperature, have been reported. For a 55-cm fiber, SFS power from 3.7755 (maximum BW condition of more than 80 nm) to 9.1837 mW (maximum power condition, BW is about 34 nm) has been achieved. The SFS mean wavelength dependence on pump wavelength is highly pump temperature sensitive, and can be reduced to zero in a chosen pump temperature field. The intrinsic variation of the SFS mean wavelength λ_m with fiber temperature is also measured, and a linear variation from 15 to 45 °C with a slop of −0.053 nm/°C for L_f = 100 cm and −0.04 nm/°C for L_f = 55 cm is found.     

Transmission system over 3000 km with dispersion compensated by chirped fiber Bragg gratings

The limitation of the system with dispersion compensation by chirped fiber Bragg gratings is investigated in this paper. The transmission distance of the system based on chirped fiber Bragg gratings surpasses 3000 km. The bit error rate (BER) of the system is below 10⁻⁹ for as long as 2000 km. The BER is about 10⁻⁷ at 3000 km and, when forward error correction (FEC) is added, zero BER can be achieved. It is the longest transmission system with dispersion compensation by chirped fiber Bragg gratings.     

Highly nonlinear photonic-crystal fibers for the spectral transformation of Cr: forsterite laser pulses

We demonstrate novel photonic-crystal fibers (PCFs) fabricated of a highly nonlinear glass. Dispersion profiles and nonlinearity of these fibers are tailored with an array of submicron holes in the fiber core. With the PCF structure designed to provide a nonlinearity on the order of 10³ W⁻¹ km⁻¹ at the radiation wavelength of 1 μm and a fundamental-mode dispersion profile with zero group-velocity dispersion around 1.19 μm, unamplified femtosecond Cr: forsterite laser pulses are efficiently frequency-converted into the 540-1000-nm wavelength range through solitonic spectral-transformation mechanisms and four-wave mixing.     

Biochemical sensor based on a novel all-fibre cavity ring down spectroscopy technique incorporating a tilted fibre Bragg grating

A novel all-fibre cavity ring down spectroscopy technique is proposed where a tilt fibre Bragg grating (TFBG) or long-period grating (LPG) in the cavity provides sensitivity to surrounding medium. Such configuration with an LPG as the representative was theoretically analyzed. Two spectral bands were identified employable for sensing of surrounding refractive index for a weak LPG while only one band existed for a strong LPG. A TFBG, with enhanced sensitivity compared to usual LPGs, was used in a ring down cavity of 1 m constructed with 2 fibre Bragg gratings as the reflectors and the decay time changed from 220 to 450 ns when the TFBG was immersed into water from air.     

The conductance and capacitance-frequency characteristics of Au/pyronine-B/p-type Si/Al contacts

The rectifying junction characteristics of the organic compound pyronine-B (PYR-B) film on a p-type Si substrate have been studied. The PYR-B has been evaporated onto the top of p-Si surface. The barrier height and ideality factor values of 0.67 ± 0.02 eV and 2.02 ± 0.03 for this structure have been obtained from the forward bias current-voltage (I-V) characteristics. The energy distribution of the interface states and their relaxation time have been determined from the forward bias capacitance-frequency and conductance-frequency characteristics in the energy range of ((0.42 ± 0.02) − E_v)-((0.66 ± 0.02) − E_v) eV. The interface state density values ranges from (4.21 ± 0.14) × 10¹³ to (3.82 ± 0.24) × 10¹³ cm⁻² eV⁻¹. Furthermore, the relaxation time ranges from (1.65 ± 0.23) × 10⁻⁵ to (8.12 ± 0.21) × 10⁻⁴ s and shows an exponential rise with bias from the top of the valance band towards the midgap.     

Highly sensitive bend sensor based on Mach-Zehnder interferometer using photonic crystal fiber

Optical fiber bend sensor with photonic crystal fiber (PCF) based Mach-Zehnder interferometer (MZI) is demonstrated experimentally. The results show that the PCF-based MZI is sensitive to bending with a sensitivity of 3.046 nm/m⁻¹ and is independent on temperature with a sensitivity of 0.0019 nm/°C, making it the best candidate for temperature insensitive bend sensors. To that end, another kind of bend sensor with higher sensitivity of 5.129 nm/m⁻¹ is proposed, which is constructed by combining an LPFG and an MZI with zero offset at the second splice mentioned above.     

New nonlinear and dispersion flattened photonic crystal fiber with low confinement loss

A new nonlinear dispersion flattened photonic crystal fiber with low confinement loss is proposed. This fiber has threefold symmetry core. The doped region in the core and the big air-holes in the 1st ring can make high nonlinearity in the PCF. And the small air-holes in the 1st ring and the radial increasing diameters air-holes rings in cladding can be used to achieve the dispersion properties of the PCF. We can achieve the optimized optical properties by carefully selecting the PCFs structure parameters. A PCF with flattened dispersion is obtained. The dispersion is less than 0.8 ps/(nm km) and is larger than −0.7 ps/(nm km) from 1.515 μm to 1.622 μm. The nonlinear coefficient is about 12.6456 W⁻¹ km⁻¹, the fundamental mode area is about 10.2579 μm². The confinement loss is 0.30641 dB/km. This work may be useful for effective design and fabrication of dispersion flattened photonic crystal fibers with high nonlinearities.     

Investigation of the D Π state of NaK by polarisation labelling spectroscopy

Two-colour polarisation labelling experiments measuring the D-X system of NaK have furnished observations of the D ¹Π state of NaK up to v″ = 42. The last observed level is located 7 cm⁻¹ below the Na(3p ²P_3/2) + K(4s) atomic asymptote, 22247.15 cm⁻¹ above the minimum of the electronic ground state, clearly indicating the dissociation products of this state. The vibrational progressions all exhibit irregular intervals, predominantly because of strong interactions with the nearby d ³Π state, which also dissociates to Na(3p) + K(4s) atoms. The polarisation data have been combined with some resolved fluorescence D-X transitions, and analysed by fitting to spectroscopic parameters and to an analytical potential curve. A full deperturbation treatment has not been attempted, but a ‘robust’ weighting scheme has been used to reduce the influence of levels that cannot be properly represented by a single channel model. Parameters determined in a fit to a potential curve include T_e = 20090.18 ± 0.02 cm⁻¹, well depth 2157.0 ± 0.3 cm⁻¹, R_e = 4.1547 ± 0.0002 Å, with an unweighted root mean square error of 0.12 cm⁻¹ for 959 data.     

Long-period fiber-gratings produced by exposure with a low-pressure mercury lamp and their sensing characteristics

A new production method of long-period fiber-gratings using neither a laser nor a fine-positioning system was proposed. A low-pressure mercury lamp emitting 254 nm ultraviolet light was used as a light source. Hydrogen-loaded Ge-B co-doped fiber was exposed to the emission of the lamp through an amplitude mask. A coupling loss up to 23 dB was obtained for a grating period of 212 μm. The maximum coupling loss for a grating period of 460 μm was 18 dB. The growth rate of the refractive index change by mercury-lamp exposure was 1.3 × 10⁻⁴/h. The temperature and strain characteristics were measured and compared with those fabricated by excimer-laser exposure. The temperature and strain sensitivities of long-period gratings with a period of 212 μm were higher than those of 460 μm. The temperature and strain sensitivities of those by mercury-lamp exposure were almost equal to those by excimer-laser exposure of the same fiber. The sensitivities of those by excimer-laser exposure of non-loaded fiber were higher than those of hydrogen-loaded fiber by mercury-lamp or excimer-laser exposures except for the temperature sensitivity of a grating period of 460 μm.     

Interatomic potentials for the ground state X 0 and the two excited states 1, 0 of the intercombination cadmium line 326.1 nm broadened by Kr pressure

The temperature dependence of the Cd line absorption profile at 326.1 nm perturbed by Kr has been carefully studied over a spectral range extending from 800 cm⁻¹ in the blue wing to 1200 cm⁻¹ in the red wing using a high-resolution double-beam spectrometer. The atomic densities of krypton (N_Kr) and cadmium (N_Cd) were (2.015±0.07)×10¹⁹ and (3.62±0.05)×10¹⁸ cm⁻³, respectively. The temperature dependence of the studied line profile was analyzed in the framework of the quasi-static theory. The van der Waals coefficient differences between the ground ¹0⁺ state and the two excited states ³0⁺ and ³1 (ΔC₆⁰ and ΔC₆¹) were obtained from the near red wing profile using Kuhn's law. The values of ΔC₆⁰ and ΔC₆¹ are found to be equal to 37.8±2 and 58.5±3 eV Å⁶, respectively. The ground (X ¹0⁺), and the excited (³1, ³0⁺) state potentials at the internuclear separations from 3.2 to 6.3 Å were determined. The well depths with their positions for these states are respectively equal to 134±7 cm⁻¹, 3.95±0.2 Å; 72.3±4 cm⁻¹, 4.95±0.3 Å; and 471±12 cm⁻¹, 3.6 Å. The obtained well depths with their allowable errors are in good agreement with the values obtained before for the Cd-Kr system from some theoretical results and molecular beams experiments.     

Vibronic and cation spectroscopy of m-chloroaniline

We applied the resonant two-photon ionization and mass-analyzed threshold ionization spectroscopic techniques to record the vibronic and cation spectra of m-chloroaniline. The band origin of the first electronic transition was found to be 33 658 ± 2 cm⁻¹, whereas the adiabatic ionization energy was determined to be 63 958 ± 5 cm⁻¹. Within our experimental detection limit, these measured values are the same for both of the ³⁵Cl and ³⁷Cl isotopomers. The observed active modes of this molecule in the electronically excited S₁ and cationic ground D₀ states mainly involve the in-plane ring deformation and substituent-sensitive bending vibrations.     

Time-resolved Fourier transform emission spectroscopy of AΠ-XΣ infrared transition of the CN radical

The A²Π-X²Σ⁺Δv = −3 bands of the ¹²C¹⁴N radical have been observed by time-resolved Fourier transform spectroscopy in the 1850-3100 cm⁻¹ region with a wavenumber resolution of 0.025 cm⁻¹. The radical was produced in a pulsed positive column discharge in a cyanogene and helium mixture. Seven bands of v = 0-3, 1-4, 2-5, 3-6, 4-7, 5-8, and 6-9 were analyzed to give the molecular constants of each state by least-squares fitting of 801 lines. The pulsed discharge was found to be efficient for production of CN in the excited A²Π state. The vibrational excitation temperature was determined to be 6680 ± 835 K and 6757 ± 534 K for the A²Π and X²Σ⁺ states, respectively. The population of the A²Π was found to be 4% of that of the X²Σ⁺ state in the time after turning off the discharge.     

Single crystal EPR and optical absorption study of Cr doped l-histidine hydrochloride monohydrate

EPR study of the Cr³⁺ ion doped l-histidine hydrochloride monohydrate single crystal is done at room temperature. Two magnetically inequivalent interstitial sites are observed. The hyperfine structure for Cr⁵³ isotope is also obtained. The zero field and spin Hamiltonian parameters are evaluated from the resonance lines obtained at different angular rotations and the parameters are: D=(300±2)×10⁻⁴ cm⁻¹, E=(96±2)×10⁻⁴ cm⁻¹, g_x=1.9108±0.0002, g_y=1.9791±0.0002, g_z=2.0389±0.0002, A_x=(252±2)×10⁻⁴ cm⁻¹, A_y=(254±2)×10⁻⁴ cm⁻¹, A_z=(304±2)×10⁻⁴ cm⁻¹ for site I and D=(300±2)×10⁻⁴ cm⁻¹, E=(96±2)×10⁻⁴ cm⁻¹, g_x=1.8543±0.0002, g_y=1.9897±0.0002, g_z=2.0793±0.0002, A_x=(251±2)×10⁻⁴ cm⁻¹, A_y=(257±2)×10⁻⁴ cm⁻¹, A_z=(309±2)×10⁻⁴ cm⁻¹ for site II, respectively. The optical absorption studies of single crystals are also carried out at room temperature in the wavelength range 195-925 nm. Using EPR and optical data, different bonding parameters are calculated and the nature of bonding in the crystal is discussed. The values of Racah parameters (B and C), crystal field parameter (Dq) and nephelauxetic parameters (h and k) are: B=636, C=3123, Dq=2039 cm⁻¹, h=1.46 and k=0.21, respectively.     

Modelling consideration of praseodymium-doped fiber amplifiers for 1.3 μm wavelength applications

To obtain the temperature-sensitive rate equations, a new energy level diagram of Praseodymium ion (Pr³⁺) in a glass host is modelled. By solving the modified rate equations, an analytical expression is presented to investigate the temperature dependence of the signal gain of a praseodymium-doped fiber amplifier (PDFA). It is seen that a change in the signal gain slightly depends on the variation of the distribution of Pr³⁺-ions in transitions ³F₄ ↔ ³F₃ with the temperature. Numerical calculations are carried out for the temperature range which is changing from −20 to +60 °C. Pr³⁺-doped ZBLAN fiber amplifier pumped at 1017 nm and Pr³⁺-doped sulfide fiber amplifier pumped at 1028 nm are selected as an application for the 1.3 μm signal wavelengths. It is also seen that the prediction of the model is in good agrement with their experimental results.