三氧化二铝-聚苯乙烯复合微球的制备

 以Al₂O₃-PS复合材料为原料，采用乳液微封装法制备出掺杂Al₂O₃的PS空心微球。三相溶液分别是两个水相：蒸馏水（W₁相）、5wt%PVA水溶液（W₂相）和3wt%Al₂O₃-PS溶液（O相，苯和三氯甲烷混合物作溶剂）。所得微球表面粗糙度低于50nm。     

采用溶胶凝胶协同自组装方法制备SiO2反蛋白石结构薄膜及其光学性质研究

研究了溶胶凝胶协同自组装制备大面积高质量SiO₂反蛋白石结构薄膜的方法. 向单分散的聚苯乙烯(PS)胶体溶液中添加SiO₂前驱物溶液,用垂直自组装法一步得到微球空隙中均匀填充有凝胶的 复合PS胶体晶体薄膜,在空气中烧结去除PS后得到SiO₂反蛋白石结构薄膜.通过对添加前驱物溶液比例、 自组装温度以及烧结温度等参数的研究,用不同粒径的PS微球制备了不同孔径的高质量SiO₂反蛋白石结构薄膜. 用扫描电子显微镜和X射线能量色散谱仪对制备得到的薄膜样品进行显微形貌和成分表征,并测试了其透射光谱. 结果表明:溶胶凝胶协同自组装法制备的SiO₂反蛋白石结构薄膜大面积高度有序,孔径可以控制且选择范围宽; 薄膜的透射光谱带隙明显,带隙中心波长与理论计算结果相符.     

CuAPTPP-TDI-TiO2光催化微球的合成及其光催化性能 (cited: 1)

采用Adler法合成了5-(4-氨基苯基)-10,15,20-三苯基卟啉铜配合物(CuAPTPP),通过甲苯二异氰酸酯(TDI)的桥联作用对TiO₂微球进行表面修饰,使TDI分子中的两个活性TDI基团分别与TiO₂表面的羟基和CuAPTPP的氨基反应,将CuAPTPP敏化剂分子以化学键合的方式固定在TiO₂表面,形成光催化微球CuAPTPP-TDI-TiO₂．通过FT-IR、XRD、SEM、EA、UV-Vis和DRS等测试手段对CuAPTPP-TDI-TiO₂进行结构表征．讨论了桥联分子TDI修饰量对光催化微球性能的影响,确定了TDI与TiO₂的最佳摩尔比．以亚甲基蓝(MB)为降解对象,考察了CuAPTPP-TDI-TiO₂微球的可见光催化性能．结果表明,桥联分子TDI在CuAPTPP与TiO₂微球表面形成了牢固的化学键,复合微球在150 W氙灯辐照下降解10 mg/LMB溶液,120 min降解率可达98.7%,其降解率过程服从一级动力学规律,测得降解速率常数为5.1×10^-2 min^-1,半衰期为11.3 min．催化微球在回收4次的条件下,对MB的降解率仍保持在90%以上．     

PS/Ag核壳结构复合微球的制备与性能

以乳液聚合法制备的平均粒径1.2~1.5μm单分散聚苯乙烯(PS)微球为核,经过超声敏化、化学镀、还原等过程制备了PS/Ag核壳结构复合微球。采用透射电镜、X射线衍射、红外光谱、紫外可见光谱对其形貌、物相、结构与光学性质进行了表征与分析。结果表明:PS/Ag复合微球粒径相对均一;通过多次敏化、控制二次银氨溶液浓度(0.002~0.006 mol/L),可实现对纳米银壳层厚度的调控;纳米银壳层沉积生长过程中,随着PS微球表面银粒子的增多、增大,复合微球的光学等离子体共振吸收峰产生显著的展宽与红移。     

间苯二酚-甲醛气凝胶空心微球制备技术

 采用微流体注射成型技术,以邻苯二甲酸二丁酯为内外油相,间苯二酚/甲醛(RF)溶液为水相,经过溶胶-凝胶、溶剂交换、超临界干燥等过程制备出了RF气凝胶空心微球。分别采用红外光谱、光学显微镜、X光显微分析、透射电镜(TEM)、N­₂吸附-脱附,对RF空心微球成分、形貌、孔径、直径分布等进行表征。结果表明：RF为单层空心微球,具有典型的气凝胶多孔结构,由粒径为10 nm左右、且粒度分布较为均匀的纳米粒子构成,平均孔径为20 nm左右,球形度和同心度大于95%,微球直径分布在550～750 mm,最大可达到800 mm,达到了快点火靶的基本要求。     

聚(N-异丙基丙烯酰胺)模板法制备二氧化硅中空微球

以在50 oC水溶液中析出的聚(N-异丙基丙烯酰胺) (PNI-PAM)聚集体作为软模板,使正硅酸乙酯吸附在PNIPAM聚集体表面进行水解缩合,原位生成二氧化硅包裹PNIPAM的核壳结构微球;进一步冷却至室温使PNIPAM溶解在水中除去内核,从而成功合成出SiO₂中空微球．实验表明,只有在足够的PNIPAM和正硅酸乙酯含量以及正硅酸乙酯水解时间下,才能形成稳定的SiO₂中空微球．用TEM、SEM和FTIR对合成的SiO₂中空微球进行了表征,结果表明,微球尺寸为150 nm左右,并且由于PNIPAM上酰胺基团和正硅酸乙酯水解出来的硅醇间具有静电相互作用,使得SiO₂壳层上依然有PNIPAM残留.     

拉曼光谱法研究纳米结构多孔ZnO微球的合成机理

利用拉曼光谱方法,对柠檬酸钠辅助水热合成纳米结构多孔ZnO微球的机理进行了研究。样品的拉曼光谱特征显示,多孔ZnO微球中存在Zn-柠檬酸配合物;分析表明反应溶液中柠檬酸钠水解产生的柠檬酸根与Zn2+结合形成Zn-柠檬酸配合物,该配合物化学吸附在Zn(OH)₂晶核的(204)和(503)晶面,使Zn(OH)₂晶核择优生长形成纳米薄片状结构;水热过程中Zn(OH)₂微晶团聚形成纳米片状结构多孔Zn(OH)₂微球并以沉淀析出。研究发现吸附在薄片表面的Zn-柠檬酸配合物提高了Zn(OH)₂微晶的热稳定性,使得Zn(OH)₂的分解温度高于200 ℃,加热到300 ℃后Zn(OH)₂完全分解获得纳米结构多孔ZnO微球。     

不同前驱体相对摩尔量对气相爆燃制备纳米SiO2的影响

 以SiCl₄为前驱体,以空气和氢气的混合气体为爆源,通过改变前驱体的相对摩尔量,考察前驱体的相对摩尔量对产物的影响。通过X射线荧光谱（XRF）、透射电子显微镜（TEM）和X射线衍射（XRD）等测试手段对纳米SiO₂粉体进行表征及分析。通过XRF对产物进行成分分析,测得实验所得产物主要由SiO₂组成,且纯度达到99.9%以上;由XRD分析得知,生成的SiO₂产物属于典型的非晶态结构;由TEM图像可以看出,随着前驱体相对摩尔量的增加,所得到的产物粒子逐渐出现粘结,分散性下降,前驱体相对摩尔比应该控制在1.5以内。     

具有双重治疗机制的磁性纳米无定型氧化铁基药物递送系统

合成一种具有pH响应性的聚乙二醇(PEG)修饰无定形介孔氧化铁纳米粒子(AFe-PEG). 这种纳米粒子可以高效负载药物分子如阿霉素(DOX)，构成新型多功能AFe-PEG/DOX药物递送体系. DOX的负载率高达948 mg/g-纳米粒子. 在酸性溶液中，AFe-PEG/DOX纳米粒子不仅可以有效释放DOX，同时可以释放Fe离子进行Fenton反应，将H₂O₂转变成·OH自由基. 体外实验结果表明，AFe-PEG/DOX纳米粒子对HeLa细胞同时具有化疗和化学动力学疗法的疗效. 同时，由于AFe-PEG/DOX 纳米粒子本身的磁性，使其在外部磁场中的细胞内化效率也得到了提高.     

从可溶性单源分子前驱体采用溶胶凝胶法制备ZnO/TiO2 纳米复合物

合成了单源分子前驱体Cl₂TiZn(dmae)₄ (dmae为2-二甲基乙醇胺),并以乙醇为溶剂,加入等摩尔量的水对其进行可控水解得ZnO/TiO₂纳米复合凝胶,经pH=9沉淀,在200、400和600 oC 烧结得到不同的产物T₂₀₀、T₄₀₀、T₆₀₀. XRD分析表明未烧结产物为无定形粉末并随着烧结温度升高晶型改善. ZnO呈纤锌矿结构(六方晶系),TiO₂呈板钛矿型结构(正交). BET分析和扫描电镜表明颗粒的大小随着烧结温度的提高而增加. 红外光谱证明Zn-O和Ti-O的特有的振动频率,OH基团烧结后的产物中被去掉. 所有的样品都显示良好的光催化活性, 且T₆₀₀活性最高.     

Efficient organic light-emitting diodes with zinc acetate as an effective electron injection layer

We report on the fabrication of organic light-emitting diodes (OLEDs) using a zinc acetate ((CH₃COO)₂Zn) layer as the cathode buffer layer. The results show that the device containing a (CH₃COO)₂Zn interlayer shows improved luminance and efficiency due to the Zn–N bond formation resulting in the occurrence of Alq₃ anion and also due to the band bending at the Alq₃/Al interface, which is beneficial to electron injection by lowering electron injection barrier. And the devices with structured cathodes (CH₃COO)₂Zn/LiF/Al and LiF/(CH₃COO)₂Zn/Al have a higher luminance and efficiency than the LiF/Al cathode-based device.     

Polishing behavior of PS/CeO2 hybrid microspheres with controlled shell thickness on silicon dioxide CMP

Organic-inorganic composite microspheres with PS as a core and CeO₂ nanoparticles as a shell were synthesized by in situ decomposition reaction of Ce(NO₃)₃ on the surfaces of PS microspheres prepared through soap-free emulsion polymerization. The shell thickness of the composite microspheres could be turned by varying the concentration of Ce(NO₃)₃ in the reaction solution. The whole process required neither surface treatment for PS microspheres nor additional surfactant or stabilizer. The as-synthesized PS/CeO₂ composite microsphere samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and thermogravimetric analysis (TGA). Oxide chemical mechanical polishing (CMP) performance of the PS/CeO₂ composite abrasives with different shell thickness was characterized by atomic force microscopy (AFM). The results indicated that the as-prepared core-shell structured composite microspheres (220-260 nm in diameter) possessed thin shell (10-30 nm) composed of CeO₂ nanoparticles (particle diameter of 5-10 nm), and the final CeO₂ contents of the composite microspheres ranged from 10 to 50 wt%. A possible mechanism for the formation of PS/CeO₂ composite microspheres was discussed also. The CMP test results confirmed that the novel core-shell structured composite abrasives are useful to improve oxide CMP performance. In addition, there is an obvious effect of shell thickness of the composite abrasives on oxide CMP performance.     

Controllable synthesis and shape-dependent photocatalytic activity of ZnO nanorods with a cone and different aspect ratios and of short-and-fat ZnO microrods by varying the reaction temperature and time

ZnO nanorods with a cone and different aspect ratios and short-and-fat ZnO microrods were synthesized via a hydrothermal reaction of Zn with Zn(CH₃COO)₂ and H₂O. The control over these ZnO nanocrystals with a wurtzite structure and different shapes was achieved by adjusting only the reaction temperature and time. A possible kinetic mechanism was proposed to account for the growth of these ZnO nanocrystals with different shapes. Photocatalytic activities of ZnO nanocrystals with distinctive shapes in the degradation of methyl orange were investigated. The results indicate that the photocatalytic ability of the ZnO nanorods with a cone and different aspect ratios is stronger than that of the short-and-fat microrods.     

Effect of excimer laser annealing on the properties of ZnO thin film prepared by sol-gel method

Pristine ZnO thin films have been deposited with zinc acetate [Zn(CH₃COO)₂], mono-ethanolamine (stabilizer), and isopropanol solutions by sol-gel method. After deposition, pristine ZnO thin films have been irradiated by excimer laser (λ = 248, KrF) source with energy density of 50 mJ/cm² for 30 sec. The effect of excimer laser annealing on the optical and structural properties of ZnO thin films are investigated by photoluminescence and field emission scanning electron microscope. As-grown ZnO thin films show a huge peak of visible region and a wide full width at half maximum (FWHM) of UV region due to low quality with amorphous ZnO thin films. After KrF excimer laser annealing, ZnO thin films show intense near-band-edge (NBE) emission and weak deep-level emission. The optically improved pristine ZnO thin films have demonstrated that excimer laser annealing is novel treatment process at room temperature.     

Induced assembly and photoluminescence of lanthanum (Tb, Eu, Dy) complexes/ZnO/polyethylene glycol hybrid phosphors

Some novel kinds of hybrid phosphors were assembled with lanthanum (Tb, Eu, Dy) complexes (with four kinds of terbium complexes is 2,4-dihydroxybenzonic acid (DHBA), 1,10-phenanthroline (phen), acetylacetone (AA) and nicotinic acid (Nic), respectively) doped ZnO/PEG particles by co-precipitation approach derived from Zn(CH₃COO)₂ (Zn(AC)₂), NaOH, PEG as precursors at room temperature. The characteristic luminescence spectra for f-f transitions of Tb³⁺, Eu³⁺, Dy³⁺ were observed. It is worthy to point out that ZnO is the excellent host for lanthanum ions by the assembly of PEG matrices.     

Fabrication of surface‐enhanced Raman scattering‐active ZnO/Ag composite microspheres

We show in this paper how zinc oxide (ZnO)/silver (Ag) composite microspheres can be prepared by the reduction of Ag(NH₃)₂⁺ with the reducing agent formaldehyde in aqueous solution on the surface of ZnO microspheres. During the preparation, Sn²⁺ was absorbed on the surface of ZnO microspheres for sensitization and activation, and then Ag(NH₃)₂⁺ was reduced to Ag nanoparticles by the reducing agent to obtain ZnO/Ag composite microspheres. SEM and TEM images revealed silver nanoparticles with a diameter ranging from tens to 100 nm. X‐Ray photoelectron spectra (XPS), X‐ray diffraction (XRD) patterns and UV‐vis spectra were used to characterize the structure of the ZnO/Ag composite microspheres. The origin of the surface‐enhanced Raman scattering properties was traced to the surface of the ZnO/Ag composite microspheres. The enhancement factor was estimated in detail, and the enhancement mechanism for the SERS effect was also investigated. Copyright © 2007 John Wiley & Sons, Ltd.     

Structural,electrical and optical studies on spray-deposited aluminium-doped ZnO thin films

Thin films of zinc oxide (ZnO) were deposited on cleaned glass substrates by chemical spray pyrolysis technique using Zn(CH₃COO)₂ as precursor solution. Also, aluminium-doped thin films of ZnO were prepared by using AlCl₃ as doping solution for aluminium. The dopant concentration [Al/Zn atomic percentage (at%)] was varied from 0 to 1.5 at% in thin films of ZnO prepared in different depositions. Structural characterization of the deposited films was performed with X-ray diffraction (XRD) studies. It confirmed that all the films were of zinc oxide having polycrystalline nature and possessing typical hexagonal wurtzite structure with crystallite size varying between 100.7 and 268.6 nm. The films exhibited changes in relative intensities and crystallite size with changes in the doping concentration of Al. The electrical studies established that 1 at% of Al-doping was the optimum for enhancing electrical conduction in ZnO thin films and beyond that the distortion caused in the lattice lowered the conductivity. The films also exhibited distinct changes in their optical properties at different doping concentrations, including a blue shift and slight widening of bandgap with increasing Al dopant concentration.     

Effect of energetic electron beam treatment on Ga-doped ZnO thin films

Transparent conductive zinc oxide (ZnO) thin films were synthesized by a sol–gel spin coating method with the addition of Ga(NO₃)₃ in a Zn(CH₃COO)₂ solution and exposed to electron beam treatment. The UV–Vis spectra demonstrated that all of the films had transmittances of over 85% in the visible region. When Ga(NO₃)₃ was added to the ZnO precursor solution, the resistivity of the ZnO thin film decreased and the carrier concentration increased significantly. After electron beam treatment was performed on the 0.4 at.% Ga-doped ZnO film, the optical band gap increased and the resistivity significantly decreased resulting from the increases of the carrier concentration and mobility. By combining Ga doping and electron beam treatment, the resistivity of the ZnO thin film was reduced by a factor of nine hundred.     

制备一维可控形貌的ZnO微米棒

用化学溶液法以醋酸锌和六亚甲基四胺为原料在玻璃衬底上生长出不同形貌的亚微米和微米ZnO棒。探讨了反应液的酸碱度和反应液浓度对生成的ZnO棒形貌的影响，并分析了其生长机制。通过控制一定的酸碱度和溶液浓度，可以得到规则的六角ZnO棒状阵列。这种规则的六角棒沿着[002]方向生长。测量了样品的XRD，扫描电镜像(SEM)，并对其发光性能进行了测量分析。其中规则六角ZnO棒的光致发光光谱中有一很强的峰值650nm红色宽谱带和一峰值约387nm的激子发光峰。激子发光峰加宽，实际上是自由激子的发光峰(380nm)和Zni的发光峰(430nm)的叠加。而红色发光峰可能是Vo2+中的电子和价带中的空穴辐射复合所致。     

Morphology of Fractured Polymer‐Polymer Interfaces Bonded at Ambient Temperature as Studied by Atomic Force Microscopy

The amorphous polymer surfaces of polystyrene (PS, M _n=200 kg/mol, M _w/M _n=1.05) and poly(methyl methacrylate) (PMMA, M _n=51.9 kg/mol, M _w/M _n≤1.07) were brought into contact at 21°C to form PS‐PS (for 54 days) and PMMA‐PMMA auto‐adhesive joints (for 11 days). After contact at that temperature corresponding to T _g‐bulk ?81°C for PS and to T _g‐bulk–88°C for PMMA, where T _g‐bulk is the calorimetric glass transition temperature of the bulk sample, the bonded interfaces were fractured and their surfaces were analyzed by atomic force microscopy (AFM). The surface roughness, R _q, of the fractured interfaces was larger by a factor of 3–4 than was that of the free PS and PMMA surfaces aged for the same period of time. A similar increase in R _q was found by comparison of the free PS surface aged at T _g‐bulk+15°C for 1 h and of the surface of the PS‐PS interface fractured after healing at T _g‐bulk+15°C for 1 h. These observations, indicative of the deformation of the fractured interfaces, suggest the occurrence of some mass transfer across the interface even below T _g‐bulk ?80°C.