含有周期球腔的黏弹性覆盖层消声性能分析

利用散射矩阵法分析了单个球状空腔在黏弹性橡胶中的Mie散射特性以及振动模式.以此为基础，利用多重散射法分析了不同背衬条件下，含有单层周期球状空腔的橡胶覆盖层(厚度为8mm)的消声性能.结果表明，单个球腔的径向共振对覆盖层的低频消声性能有重要贡献，覆盖薄层在共振区具有良好的消声性能.最后，设计了双层消声覆盖层(厚度为20mm)，有效拓展了消声带宽. 关键词： Mie散射 多重散射法 消声材料 声子晶体     

Negative refraction imaging of solid acoustic waves by two-dimensional three-component phononic crystal

By using of the multiple scattering methods, we study the negative refraction imaging effect of solid acoustic waves by two-dimensional three-component phononic crystals composed of coated solid inclusions placed in solid matrix. We show that localized resonance mechanism brings on a group of flat single-mode bands in low-frequency region, which provides two equivalent frequency surfaces (EFS) close to circular. The two constant frequency surfaces correspond to two Bloch modes, a right-handed and a left-handed, whose leading mode are respectively transverse (T) and longitudinal (L) modes. The negative refraction behaviors of the two kinds of modes have been demonstrated by simulation of a Gaussian beam through a finite system. High-quality far-field imaging by a planar lens for transverse or longitudinal waves has been realized separately. This three-component phononic crystal may thus serve as a mode selector in negative refraction imaging of solid acoustic waves.     

Comparison of the mechanism of gap formation for tri- and bi-component phononic crystal

Using an exact Mie scattering solution, this paper investigates the mode conversions during the Mie scattering of a single bi- or one-component sphere in unbounded epoxy. Then the formation mechanism of the first complete gap in the corresponding tri- or bi-component phononic crystal is investigated by the multiple-scattering method. It is shown that the heavy density of the scatterer plays an essential role in the Mie resonance and the formation of the gaps for both types of the phononic crystals. For the tri-component phononic crystal, the gap is mainly induced by the Mie resonance of the single scatterer. For the bi-component phononic crystal, the transverse wave （by mode-conversion during the Mie scattering under a longitudinal wave incidence） is modulated by the periodicity and governed by the Bloch theory, which induces the gap cooperatively.     

Backing effects on the underwater acoustic absorption of a viscoelastic slab with locally resonant scatterers

Backing effects on the underwater acoustic absorption of a viscoelastic polymer slab embedded with locally resonant scatterers are reported. The polymer slab is embedded with two layers of locally resonant scatterers, i.e. Al spheres coated by soft silicon rubber. Theoretical absorption coefficients of the polymer slab under different backings using a layer multiple scattering method show good agreement with the experimental results, which supports unambiguously the experimental observation. Then relations between the resonance modes and the low-frequency absorption peaks of the composite slab are clarified to address the absorption mechanisms. It shows that the mass of the steel backing affects evidently the low-frequency absorption, the absorption peak shifts to lower frequency range while increasing the backing mass.     

Sound Absorption of Locally Resonant Sonic Materials

The acoustic properties of locally resonant sonic materials with viscosity are theoretically investigated by using the multiple-scattering approach. We find that the absorption of a two-layer slab dominates the wave attenuation in the resonant frequency region under the condition of moderate or high viscous level. The fundamental mechanism operating in local resonance for absorption is investigated for the viability by the mode translation in the scattering process of a single scatterer. Finally the absorption performance in a multi-layer system is discussed.     

内插扩张室声子晶体管路带隙特性研究

声子晶体管路的带隙特性,可以实现管路系统在特定频率下的噪声控制.利用二维模态匹配法推导出单个内插扩张室元胞的传递矩阵,结合Bloch定理,得到声子晶体管路的能带结构计算方法;验证了二维方法在计算能带结构时的准确性.研究发现,内插扩张室声子晶体管路存在布拉格带隙和局域共振带隙.进一步研究了晶格常数以及内插管长度对能带结构的影响,结果表明,晶格常数主要控制布拉格带隙,而内插管长度对局域共振带隙有较大的影响,并研究了两种参数变化下的带隙耦合.研究结果可以为管路降噪设计提供新的思路.     

基于局域共振单元实现声子晶体低频多通道滤波

从理论上提出一种由局域共振单元组成的声子晶体低频多通道滤波模型.在二维三组元局域共振声子晶体中引入不同填充率的共振单元构成波导结构,通过有限元法计算出其能带结构、透射曲线和透射场图.结果显示:这种设计能够在低频带隙范围内不同填充率散射体的共振频率附近产生新的分立模,且这些分立模能够使相应的声波在声子晶体中沿波导方向传播;这些分立模只与相应的共振单元相关,抗干扰能力强.所得结果为低频多通道滤波器的设计提供了一种新的理论依据.     

新型二维压电声子晶体板带隙可调性研究

设计了一种由涂有硬质材料涂层的柱状压电散射体周期性连接在四个环氧树脂薄板上构成的具有大带宽的新型二维压电声子晶体板,并利用有限元方法计算了该声子晶体板的能带结构、传输损失谱和位移矢量场.研究表明：与二组元材料构成的传统声子晶体板相比,新设计的声子晶体板的第一完全带隙频率更低,并且带宽扩大了5倍;通过在压电体表面上施加不同的电边界条件,可以实现多条完全带隙的主动调控;压电效应对能带结构有很大的影响,并且有利于完全带隙的扩大与形成.基于带隙的可调谐性,分析了可切换路径的压电声子晶体板波导,结果表明可以通过改变电边界条件来限制弹性波能量流.     

局域共振复合单元声子晶体结构的低频带隙特性研究

本文提出了一种新型局域共振复合单元声子晶体结构, 并结合有限元方法对结构的带隙机理及低频共振带隙特性进行了分析和研究. 共振带隙产生的频率位置由所对应的局域共振模态的固有频率决定, 并且带隙宽度与局域共振模态的品质因子及其与基体之间的耦合作用强度有关. 采用局域共振复合单元结构可以实现声子晶体的多重共振, 在低频范围能打开多条共振带隙, 但受到共振单元排列方式的的影响. 由于纵向和横向局域共振模态的简并, 复合单元结构能在200 Hz以下的低频范围打开超过60%宽度的共振带隙, 最低带隙频率低至18 Hz. 这为声子晶体结构获得低频、超低频带隙提供了一种有效的方法. 关键词： 局域共振 低频带隙 复合单元 声子晶体     

基于等效参数反演的敷设声学覆盖层的水下圆柱壳体声散射研究

应用了一种等效方法计算敷设声学覆盖层无限长圆柱壳体水下声散射特性.等效方法的核心是忽略复杂声学覆盖层内部的声学结构,将其作为具有等效材料参数的均匀阻尼层进行建模,该均匀阻尼层具有和原覆盖层相同的复反射系数.进而,应用COMSOL Multiphysics软件建立敷设均匀阻尼层圆柱壳体的有限元模型并求解其声散射特性.等效方法的关键是等效材料参数的获取.采用充水阻抗管实验和有限元数值实验两种方法获取声学覆盖层贴敷在与壳体具有相同厚度、相同材料背衬条件下的复反射系数,在此基础上,基于遗传算法反演材料的等效参数.研究表明,等效参数具有频变特性,且尽管等效杨氏模量和等效泊松比在频率范围内存在较大波动,但是等效前后复反射系数仍保持一致.为了验证等效方法求解壳体声散射特性的准确性,同时建立了敷设声学覆盖层壳体的完整有限元模型,将覆盖层内部声学结构进行精细建模,并求其声散射特性.结果表明,两种方法求得的形态函数符合得较好,在整个频率范围内平均误差大约为1 d B.     

Analysis of absorption performances of anechoic layers with steel plate backing

Rubber layers with air-filled cavities or local resonance scatters can be used as anechoic coatings. A lot of researches have focused on the absorption mechanism of the anechoic coatings. As the anechoic coatings are bonded to the hull of submarine, the vibration of the hull should not be neglected when the analysis of the absorption characters is carried out. Therefore, it is more reasonable to treat the anechoic coating and the backing as a whole when the acoustic performance is analyzed. Considering the effects of the steel plate backing, the sound absorption performances on different models of anechoic coatings are investigated in this paper. The Finite Element Method is used to illustrate the vibrational behaviors of the anechoic coatings under the steel backings by which the displacement contours is obtained for analysis. The theoretical results show that an absorption peak is induced by the resonance of the steel slab and rubber layer. At the frequency of this absorption peak, the steel plate and the coating vibrates longitudinally like a mass-spring system in which the steel slab serves for mass and the coating layer is the spring. To illuminate the effects of the steel slab backing on the acoustic absorption, the thicknesses of the steel slab and the anechoic layer are discussed. Finally, an experiment is performed and the results show a good agreement with the theoretical analysis.     

二维空心散射体声子晶体板的低频带隙特性及其形成机理

利用有限元方法,对设计的涂有硅橡胶包裹层的空心铅柱体嵌入到4个环氧树脂短连接板中构成的声子晶体板的低频带隙特性进行了研究,分析了其能带结构、传输损失及位移场。与正方连接板粘连结构、嵌入结构和细连接短板粘连结构这3种传统声子晶体板的带隙特性作对比,说明具有包裹层、短连接板结构的声子晶体板更容易产生低频宽带;观察位移矢量场的振动模态,并结合弹簧质量模型,解释了带隙形成的机理;通过讨论连接板的宽度、散射体的内外半径及高度对第一完全带隙的影响,说明连接板宽度越窄,厚度越小,散射体内半径越小,外半径越大,高度越高,越有利于带隙的扩展。      

In-plane attenuation zone and its optimization in a plate with periodic holes

It is difficult to design a plate with wide attenuation zones in low frequency region based on Bragg scattering mechanism. A plate with periodic rhombic holes is optimized and designed. Based on the finite element method under periodic boundary conditions, the in-plane dispersion curves of periodically perforated plate are calculated via COMSOL. The frequency responses of periodically perforated plate axe investigated via ANSYS simulation. The plates with periodic holes are suspended and dynamically tested under sinusoidal excitations. The results show that a periodically perforated plate with rhombus holes has wider attenuation zones than plates with circular and hexagonal holes. Material properties have a great influence on attenuation zones: nitrile-butadiene rubber and silicon rubber can easily obtain low-frequency zones, while increasing porosity creates lower and wider zones. The width of attenuation zone increases as the horizontal angle of the rhombus holes increases. An analysis of the attenuation zones* generation mechanism shows that the plate with periodic holes exhibits characteristics of Bragg scattering and local resonant phononic crystal, indicating an inherent relationship between two types of mechanisms. The optimized plate has a complete attenuation zone ranging from 5281.76-8824.30 Hz. The vibrations are significantly reduced when the number of periods is no less than two. The attenuation range obtained via the numerical method is generally consistent with the experiment. The research sheds light on the noise insulation plate and has the potential to improve the sound environment in various applications due to its simple manufacturing.     

声波在二维固/流声子晶体中的禁带特性研究

采用时域有限差分法(FDTD),分析了声波在二维四方点阵铝/空气组合声子晶体中的禁带特性,并利用实验测试验证了理论分析的正确性.在此基础上研究了两种不同声阻抗率比固(实心圆柱和空心圆管)/流系统声子晶体的禁带特性.对于实心圆柱体,分析了有限尺寸结构声子晶体在传播方向上的层数对声波传播特性的影响,得到了这两种系统在不同填充率下取得最大声波禁带宽度所需的最少层数.同时指出,在低声阻抗率比条件下,对于空心圆管填充物,通过选取适当的半径比,可以获得比实心柱体更宽的方向带隙.     

近似声斗篷的多层介质覆盖水中弹性球壳的声散射

对水中弹性球壳的低频覆盖层消声效果和消声机理进行研究。声斗篷(Acoustic cloak)是各向异性的超常材料,根据有效介质近似理论(Effective MediumApproximationTheory),采用各向同性多层介质近似各向异性材料的声斗篷,推导出覆盖多层介质水中弹性球壳散射声场的解析表达式,计算了弹性球壳覆盖多层介质前后的散射形态函数、谐振模态以及声场分布,分析了覆盖前后球壳的声散射特性和声传播机理。研究表明,覆盖层内的声波在多层介质之间的声传播方向发生改变,声场形成弯曲变形,声能流绕过目标,这不仅极大的降低了低频散射强度,而且使到达弹性体表面的声场强度非常小,散射频响中除了0阶子波产生的第一个谐振峰外,无法激发弹性球壳的其它谐振模态,有效的抑制弹性球壳的谐振散射。      

Surface Tamm states in a photonic crystal slab with asymmetric termination

The reflection and transmission spectra of a finite thickness 2D photonic crystal slab (PCS) based on macroporous silicon are investigated. Periodic photonic crystal region is separated from air by homogeneous silicon interfacial layers. These interfacial layers at the silicon/air boundary being defects of the photonic crystal lattice, define the properties of surface Tamm states in the photonic stop‐bands (PSBs). It is demonstrated experimentally and theoretically that the reflection spectra of a structure with different thicknesses of the interfacial layers on both sides of the PCS depend on the illuminated side. At the same time, the transmission spectra are identical for both light directions in agreement with the reciprocity principle. Analysis shows that the dependence of the reflection spectrum on the side of light entrance is due to scattering losses in the real structure. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Large complete band gap in two-dimensional phononic crystal slabs with elliptic inclusions

Phononic band structure with periodic elliptic inclusions for the square lattice is investigated based on the plane wave expansion method. The numerical results show the systems composed of tungsten (W) elliptic rods embedded in a silicon (Si) matrix can exhibit a larger complete band gap than the conventional circular phononic crystal (PC) slabs. The phononic band structure of the plate-mode waves and the width of the first complete band gap can be tuned by varying the ratio of the minor axis and the major axis, the orientation angle of the elliptic rods and the thickness of the PC slabs. We also study the band structure of plate-mode waves propagating in two-dimensional (2D) slabs with periodic elliptic inclusions coated on uniform substrate.     

Band structure characteristics of T-square fractal phononic crystals

The T-square fractal two-dimensional phononic crystal model is presented in this article.A comprehensive study is performed for the Bragg scattering and locally resonant fractal phononic crystal.We find that the band structures of the fractal and non-fractal phononic crystals at the same filling ratio are quite different through using the finite element method.The fractal design has an important impact on the band structures of the two-dimensional phononic crystals.     

平板二维声子晶体声波能带结构研究

利用超元胞法,研究由钢板上生长有限长度的钢柱体形成的散射体嵌入环氧树脂基体中所构成的平板二维声子晶体的声波能带结构,分析散射体的几何参数如柱体的高、半径和板的厚度对声波带隙的影响。研究结果表明:(1)这种新型的声子晶体具有很宽的带隙,且带隙出现在低频范围内;(2)散射体的几何参数对带隙的宽度有很大的影响,它们是控制带隙宽度的主要因素。     

周期多孔板的面内振动衰减域及其优化

针对Bragg散射型周期多孔板难以实现较低起始频率并维持较宽衰减域的问题,优化设计了一种含菱形孔的周期多孔板。采用有限元法结合周期边界条件,并运用COMSOL对周期多孔板的面内弹性波频散关系进行计算,通过ANSYS模拟有限尺寸周期多孔板的频率响应,将周期多孔板悬吊进行了正弦波激励的振动试验。研究结果表明,含菱形孔的周期多孔板相比于含圆形和六边形孔的周期多孔板具有更宽的衰减域;材料属性对衰减域影响较大,丁晴橡胶和硅橡胶易于获得低频衰减域;孔隙率的增大有利于获得低频宽带的衰减域;增大菱形孔水平夹角能获得较宽的衰减域。对衰减域的形成机理分析发现,含菱形孔的周期多孔板同时具有Bragg散射型和局域共振型声子晶体的特性,表明两种衰减域机理具有内在的联系。优化设计的周期多孔板存在一条5281.76 Hz至8824.30 Hz的完全衰减域,经过至少2个周期,振动即得到较明显衰减。数值和试验得到的衰减区具有较高的一致性。该研究为减振降噪板的开发提供了新的思路,且由于制作过程便捷,在改善建筑声环境中具有潜在的应用前景。