Non-isothermal crystallization kinetics of alkyl-functionalized graphene oxide/high-density polyethylene nanocomposites

Dodecyl amine-functionalized graphene oxide (DA-GO) was obtained via an amidation reaction. The results of X-ray diffraction and Fourier-transform infrared spectroscopy verified that long alkyl chains of DA were successfully grafted on the GO sheets. Transmission electron microscope and scanning electron microscope techniques illustrated that homogeneously dispersed DA-GO/high-density polyethylene (HDPE) nanocomposites were obtained. The effects of DA-GO on the non-isothermal crystallization of HDPE were then investigated by differential scanning calorimetry (DSC) at various cooling rates (2, 5, 10, and 20?°C/min). Significant increase in the onset crystalline temperature (T_o) and the peak crystallization temperature (T_p) of HDPE incorporating DA-GO indicated the strong nucleating ability of DA-GO. The investigation of half-time crystallization time (t_1/2) demonstrated that crystallization rate of HDPE consisting of DA-GO is faster than that of pure HDPE at a given cooling rate. Ozawa, Avrami, and the combined Avrami–Ozawa methods (Mo) were used for analyzing experimental data. The Mo approach was successful in describing the non-isothermal crystallization process of DA-GO/HDPE nanocomposites. The results indicated that low DA-GO content accelerates the crystallization of HDPE, while higher content hinders the crystallization of HDPE.     

Effect of Ni(II) substitution on phase stabilization electrical properties of BICo(III)VOX.20 oxide-ion conductor

The BICO_0.20–xNI_xVOX solid electrolyte was synthesized by the standard solid-state reaction. The effect of Ni(II) substitution for Co(III) on phase stabilization and oxide-ion performance has been investigated in the compositional range 0?≤?x?≤?0.20 using X-ray powder diffraction, differential thermal analysis and AC impedance spectroscopy. The highly conductive γ′-phase was effectively stabilized at room temperature for compositions with x?≥?0.13 whose thermal stability increases with Ni content. The complex plane plots of impedance were typically represented at temperatures below 380?°C, suggesting a major contribution of polycrystalline grains to the overall electrical conductivity. The dielectric permittivity measurements revealed the fact that suppression of the ferroelectric transition is compositionally dependent. Interestingly, the maximum ionic conductivity at lower temperatures (~2.56?×?10^?4?S^?cm^?1 at 300?°C) was observed for the composition with x?=?0.13. The variation of low-temperature conductivity with Ni content was accompanied with a general drop in the corresponding values of ΔE_LT. However, the local minimum high-temperature conductivity, σ₆₀₀?°C?~?2.26?×?10^?2?S^?cm^?1 for x?=?0.10, coupled with a local maximum value of ΔE_HT?~?0.48?eV was attributed to an increased defect trapping effect correlated with the V(V)?→?V(IV) reduction at elevated temperatures.     

STICK-SLIP TYPE CRACK GROWTH DURING INSTRUMENTED HIGH-SPEED IMPACT OF HDPE AND HDPE/SELAR® DISCONTINUOUS LAMINAR MICROLAYER COMPOSITES

Stick-slip type crack growth was triggered in high-density polyethylene (HDPE) and HDPE/Selar® discontinuous laminar microlayer composites by instrumented Charpy impact under suitable test conditions (temperature ?40°C, hammer speed 3.7 m/s). Fractographic analysis showed that crazing is responsible for this peculiar fracture. The onset of this stick-slip phenomenon was favored by a mixed plane strain/plane stress condition prevailing in the specimens. The relative orientation of the Selar microlayers in respect to the crack growth direction affected the stick-slip type crack growth and the related failure considerably. No stick-slip type crack propagation was observed when gasoline-plasticized specimens were impacted, which failed by ductile tearing instead of crazing.     

Effect of high hydrostatic pressure processing and squeezing pressure on some quality properties of pomegranate juice against thermal treatment

The aim of this study was to investigate the effect of high hydrostatic pressure (HHP) treatment (200, 300, 400?MPa; 5°C, 15°C and 25°C; 5 and 10 min) on some quality properties of pomegranate juice. Juice samples are obtained under industrial conditions at two different squeezing pressure levels (100 and 150?psi – 0.689 and 1.033?MPa, respectively). Results are compared against conventional thermal treatment (85°C/10 min) and raw sample. For all three processing temperature, HHP combinations at 400?MPa for 10 min were sufficient to decrease the microbial load around 4.0 log cycles for both squeeze levels. All HHP treatments showed no significant decrease at antioxidant activity, total phenolic content and monomeric anthocyanin pigment concentrations, while there was a significant decrease (p?≤?.05) in thermal-treated samples. Being the highest sugar alcohol in pomegranate juice, mannitol content must be considered for determining the authenticity, and mannitol content increased with squeezing pressure and thermal treatment.     

Isothermal Crystallization and Melting Behavior of Composites Composed of Poly(L-lactic Acid) and Poly(glycolic Acid) Fibers

Several composites of poly (L-lactic acid) (PLLA) with poly (glycolic acid) (PGA) fibers were prepared. The isothermal crystallization kinetics and melting behavior of PLLA and all of the composites were characterized by using differential scanning calorimetry. The experimental data were processed by using the Avrami equation. The relative parameters, such as the Avrami exponent and half-time crystallization, revealed that PGA fibers had positive effects on the crystallization of PLLA, but these effects had only a minimal dependence on the PGA fiber content. Moreover, at low isothermal crystallization temperatures (85°C～110°C), recrystallization during the heating scan was observed, which could lower the melting point of the samples to a certain extent.     

Physical and Thermal Properties of High-Density Polyethylene Film Modified with Polypropylene and Linear Low-Density Polyethylene

Abstract

In view of the toughness and processing difficulty of high-density polyethylene (HDPE) film, the HDPE was modified by polypropylene (PP) and linear low density polyethylene (LLDPE), and the melt index, haze, dart impact strength, elongation at break were characterized. In addition the infrared spectra (IR), scanning electron microscopy (SEM), infrared image analysis, and differential scanning calorimetry (DSC) data were obtained. The results showed that the toughening effect of the 10%PP/30%LLDPE/60%HDPE composition was the best; the haze was reduced 6% and its dart impact strength and elongation at break were increased by 27.3% and 47%, respectively, relative to the pure HDPE. The blend of 10%PP/30%LLDPE/60%HDPE had compatibility. The melting point of the 10%PP/30%LLDPE/60%HDPE blend film increased by 5?°C compared with the pure HDPE film, with the results indicating the application fields of HDPE film could be widened.     

Interphase sizing temperature effect of LaRC PETI-5 on the dynamic mechanical thermal properties of carbon fiber/BMI composites

The dynamic mechanical thermal properties of carbon fiber-reinforced bismaleimide (BMI) composites processed using polyacrylonitrile(PAN)-based carbon fibers unsized and sized with LaRC PETI-5 amic acid oligomer as interphase material at 150°C, 250°C, and 350°C were investigated by means of dynamic mechanical thermal analysis. It was found that the storage modulus, loss modulus, tan δ and the peak temperature significantly depend on the sizing temperature as well as on the presence and absence of LaRC PETI-5 sizing interphase. The result showed that the carbon fiber/BMI composite sized at 150°C had the highest storage modulus at a measuring temperature of 250°C. The storage modulus decreased with increasing sizing temperature from 150°C to 350°C, being influenced by interdiffusion and co-reaction between the LaRC PETI-5 interphase and the BMI matrix resin. The present result is quite consistent with the interfacial result reported earlier in term of interfacial shear strength and interlaminar shear strength of carbon fiber/BMI composites. It is addressed that in the present composite system the sizing temperature of LaRC PETI-5 interphase critically influences not only the interfacial properties but also the dynamic mechanical thermal properties and its control is also important.     

Hematite reaction with tar to produce carbon/iron composites for the reduction of Cr(VI) contaminant

In this work, highly reactive carbon–iron composites were prepared using a waste, i.e. tar, as carbon precursor and a simple iron oxide, i.e. hematite. Tar was impregnated on Fe₂O₃ with different tar/hematite weight ratios of 1:1; 2:1 and 4:1, and thermally treated under N₂ atmosphere (400°C, 600°C and 800°C). Mössbauer, XRD and magnetization measurements suggested that treatment at 400°C and 600°C produces Fe₃O₄ but treatment at 800°C produced mainly Fe°. Raman and TG analyses of the different composites suggested the formation of carbon contents of 18, 24 and 32 wt.% as amorphous and graphitic highly dispersed on the Fe surface. The composites obtained at 800°C showed high efficiency to reduce Cr(VI) as CrO $_{4}^{2-}$ in aqueous medium with much better results compared to finely ground commercial Fe°.     

Banana fiber strands–reinforced polymer matrix composites

Banana fiber (BF)-reinforced low-density polyethylene (LDPE) unidirectional composites were fabricated by the compression molding process with 40 wt% fiber loading. The fibers were modified with methylacrylate (MA) mixed with methanol (MeOH) along with 2% benzyl peroxide under thermal curing method at different temperatures (50–90 °C) for different curing times (10–50 min) in order to have better compatibility with the matrix. The effect of fiber surface modification on the mechanical properties (tensile and impact properties) of the composites were evaluated. Monomer concentration, curing temperature, and curing time were optimized in terms of polymer loading and mechanical properties. The mechanical properties were found to be improved based on the improved interaction between the reinforcement and the matrix. Optimized BFs were again treated with 2–5 wt% starch solutions and composites made of 4% starch treated BF showed the highest mechanical properties than that of MA treated composites. Scanning electron microscopy (SEM) was performed to get an insight into the morphology of the composites. Water uptake and soil degradation test of the composites were also investigated.     

Influence of Carbon Nanotubes on the Crystallization and Directional Tensile Behavior of High-Density Polyethylene Prepared by Dynamic-Packing Injection Molding

The influence of multi-walled carbon nanotubes (MWCNTs) on the crystallization and directional tensile properties of high-density polyethylene (HDPE) was studied for samples prepared by dynamic-packing injection molding (DPIM). Oscillatory shear was imposed on the gradually cooled melt during the packing solidification stage of DPIM. For the oriented composites containing 1.8 wt% MWCNTs, the tensile fracture behavior showed typical brittle features along the flow direction (FD) and perpendicular direction (PD), which were almost the same as those that occurred in oriented pure HDPE. The elongation at break along both directions decreased due to the incorporation of MWNCTs in the oriented composites compared with the oriented pure HDPE. However, the tensile strength of the oriented HDPE/MWCNT composites was greatly improved along the FD due to the presence of carbon nanotubes; meanwhile, it was not weakened along the PD. In scanning electron microscopy observations, it was found that there were some oriented hybrid shish-kebab structures in a nanometre scale in the oriented HDPE/MWCNT composites, but not in its isotropic composites. This suggests that MWCNTs were involved in the shear-induced crystallization of HDPE. Differential scanning calorimetry measurements confirmed that the crystallinity of oriented HDPE composites with 1.8 wt% MWCNTs was higher than those of isotropic HDPE and isotropic composites, but was not obviously higher than that of oriented pure HDPE. These findings demonstrate that MWCNTs indeed affected the formation of crystalline structures, but did not greatly influence the crystallinity of HDPE under shear flow. The transition of crystalline morphology might be the reason for change in tensile behavior for the oriented HDPE/MWCNT composites compared with the oriented pure HDPE.     

Internal friction in directed-crystallization (Cu-Sn)-Nb alloys

The distinctive features of the low-frequency internal friction Q ⁻¹(T) of (Cu-Sn)-Nb composites at high temperatures (up to 400°C) are investigated for strains in the range 10⁻⁵–10⁻⁴. Considerable hysteresis of Q ⁻¹(T) in the heating-cooling cycle is recorded, including the presence of a minimum at ∼175°C when the sample is heated to 400°C and two peaks P ₂ (at 280°C) and P ₁ (at ∼100°C) when the sample is cooled from 400°C. The activation energy of the anomalous internal friction background (up to 175°C), the oxygen diffusion parameters, and the oxygen concentration in the niobium fibers (all of which govern the peak P ₂) are calculated, and the value and temperature dependence of the yield point of the bronze matrix (which govern the peak P ₁) are estimated. Zh. Tekh. Fiz. 68, 114–117 (November 1998)     

Effect of annealing temperature on K-shell X-ray fluorescence parameters of zinc oxide thin films prepared by the sol-gel method

Zinc oxide thin films were grown on a glass substrate by a sol-gel process using a spin-coating technique. The obtained thin films were annealed between 350?°C and 550?°C in 50?°C steps and were then characterized using X-ray diffraction, scanning electron microscopy, and X-ray fluorescence techniques. The samples were stimulated by 59.5?keV gamma rays emitted from an Americium-241 annular radioisotope source. K X-rays emitted by samples were counted using an ultra-low energy germanium detector with a resolution of 150?eV at 5.96?keV. It was found that there was generally a decrease in both the Kβ/Kα X-ray intensity ratios and the K X-ray fluorescence cross sections for zinc oxide between 350?°C and 500?°C, but not at 550?°C. In addition, the X-ray diffraction patterns of the films showed that the transition phase from an amorphous to a polycrystalline hexagonal wurtzite structure was complete at an annealing temperature of 500?°C. The results show that variations in these parameters can be explained by the reorganization of atoms and the charge transfer process due to the effect of the annealing temperature on the elements forming the compounds.     

Polymer-precursor-derived (am-) SiC/TiC composites for resistive heaters in large volume multi-anvil high pressure/high-temperature apparatus

(Amorphous-)SiC/TiC composites for resistive tubular heaters in HP/HT experiments were obtained via a polymer-precursor process. A slurry consisting of a commercial SiC-precursor polymer (allylhydridopolycarbosilane, AHPCS) and TiC powder as conductive filler was applied to the inner walls of zirconia insulation tubes, using a centrifugation-casting method. Resistive coatings with homogeneous thickness of ～200 μm were obtained. The heaters were tested in octahedral multi-anvil assemblies at ～10 GPa with simultaneous recording of heating voltage and current. Up to a maximum temperature of ～1800°C they showed temperature vs. power characteristics reproducible from batch to batch, with resistance decreasing from 0.08 to 0.02 Ω during heating. Microstructural characterization using SEM/EDX was carried out on the recovered SiC/TiC composite material, as well as on pristine resistive heaters directly after coating and curing to 230°C, and after additional pyrolysis at 900°C in argon. In all cases, a stable composite microstructure of an interpenetrating network of TiC particles with either silicon carbide polymer precursor or an amorphous SiC phase were found. The composites were characterized by XRD and thermogravimetry. Further improvement of coating procedure and materials combination (precursor/filler/insulator substrate) may result in advanced coatings, operational well beyond 2000°C.     

Melting and Crystallization Behaviors of Poly(Lactic Acid) Modified with Graphene Acting as a Nucleating Agent

Graphene (GN)-filled polylactic acid (PLA) nanocomposites were prepared through a solution blending method with GN weight percent ranging from 0.5 to 2?wt%. Rheological, melting and crystallization behaviors of the prepared PLA/GN nanocomposites were investigated by means of dynamic rheological measurements and differential scanning calorimetry (DSC). The shear viscosities of the PLA/GN nanocomposites decreased with increasing GN content, which was remarkably different from previous reports on the modifications using traditional nanofillers (e.g., clay, carbon nanotubes, etc.). The nonisothermal melt crystallization kinetic analysis suggested that GN served as a nucleating agent and could considerably promote the PLA’s crystallization through heterogeneous nucleation. Our findings suggested that at relatively low cooling rates (??≤?10?°C/min) even a small amount of GN promoted the nucleation and considerably increased the crystallization rate. However, the crystallinity began to decrease at higher cooling rates (e.g., ??≥?20?°C/min), especially when the GN content was high (e.g., 2?wt%), possibly owing to the GN aggregation effect considering PLA is a slowly crystallizing polymer.     

The Fe–Fe2P phase diagram at 6 GPa

Here, we report experimental results on melting and subsolidus phase relations in the Fe–Fe₂P system at 6?GPa and 900–1600°C. The system has two P-bearing compounds: Fe₃P and Fe₂P. X-ray diffraction patterns of these compounds correspond to schreibersite and barringerite, respectively. The Fe–Fe₃P eutectic appears at 1075°C and 16?mol% P. Schreibersite (Fe₃P) melts incongruently at 1250°C to produce barringerite (Fe₂P) and liquid containing 23?mol% P. Barringerite (Fe₂P) melts congruently at 1575°C. Maximum solid solution of P in metallic iron at 6?GPa is 5?mol%. As temperature increases to 1600°C, the P solubility in the metallic iron decreases to 0.5?mol%, whereas the P content in coexisting liquid decreases to 3?mol%. The composition of quenched phases from Fe–P melt coincides with the compositions of equilibrium phases at corresponding temperature. Consequently, the composition of quenched products of Fe-P melts in meteorites can be used for reconstruction of P–T conditions of their crystallization under ambient or low pressures or during shock melting by impact collisions.     

On the low temperature phase transition in (NH4)2SO4

An ultracryostat and multidecameter were used to determine the temperature dependence of the dielectric constant ?′ and dielectric loss ?″ over a wide range of frequencies of single crystals and polycrystalline samples of (NH₄)₂SO₄ in the region of the low temperature phase transition. A sharp increase was observed in the values of ?′ and ?″ at about ?50°C. In addition, a dielectric dispersion was detected and found to be more pronounced in the high temperature phase. This dispersion was attributed to piezoelectric resonance. The observed sudden increase in the values of the dielectric constant and dielectric loss below ? 50°C was attributed to the ferroelectric nature of the low temperature phase of (NH₄)₂SO₄.A DTA thermogram showed a sharp peak at ? 50°C which indicated that the phase transition is one of first order type. A TMA thermogram showed that this transformation was associated with a rapid increase in the expansion coefficient. Such an increase in the lattice parameter might be attributed to the enhanced rotation of electric dipoles associated with the distorted NH₄⁺ and SO₄^2? ions. The distortion of both the ammonium and sulfate ions in addition to their expected orientational motion are suggested to be responsible for the ferroelectric behaviour of ammonium sulfate below ?50°C.A transition to a metastable hexagonal state at about ?40°C is thought to occur, and this transformation is found to be irreversible.     

Effect of Alkali Treatment on Structure and Mechanical Properties of Acrylonitrile–Butadiene–Styrene/Bamboo Fiber Composites

The preparation and properties of wood–plastic composites (WPCs) based on acrylonitrile–butadiene–styrene (ABS) and bamboo fibers (BFs) are described. The BFs were first modified by alkali treatment in order to improve their adhesion to an ABS matrix. The BF modifications were monitored by Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). Styrene–maleic anhydride (SMA) copolymer, as a compatibilizer, was added to both the untreated and alkali-treated composites. The changes in the structure and the properties resulting from these treatments were observed by the SEM and mechanical tests. The experimental results indicated that both the alkali treatment of the BF and the inclusion of the SMA copolymer improved the interactions between the BF and ABS matrix, and promoted better mechanical properties of the composites.     

Evaluation of the geopolymer/nanofiber interfacial bond strength and their effects on Mode-I fracture toughness of geopolymer matrix at high temperature

The present article has reported the effects of several nanofiller’s aspect ratio, length and interfacial strength on Mode-I fracture toughness (K_IC) of geopolymer as the matrix of continuous fibre reinforced composites. These nanofillers have been chosen based on the variations in the surface chemistry and nature of interfacial bonding with geopolymer, which include Carbon, Alumina and Silicon carbide. Geopolymer matrix was subjected to the addition of single volume fraction, 2% of each type of nanofiller with two aspect ratios, designated as nanoparticles and nanofibers. Notched beam flexure tests (SEVNB) of neat and each nanofiller reinforced samples suggest that, while baseline K_IC of neat geopolymer improved with heat treatment, nanofibers with high interfacial bond strength showed maximum capability in further improving K_IC. Among those nanofibers, 2 vol% Silicon Carbide Whisker (SCW) showed the largest improvement in K_IC of geopolymer, which is ~164%. After heat treatment at 650 °C, SCW reinforcement was also found to be effective, with only ~28% lower than the reinforcing performance at 250 °C, while the performance of Alumina Nanofiber reinforced geopolymer notably reduced. SEM and EDS analysis suggested that the inhomogeneity in neat geopolymer and length of nanofibers control the reinforcing capability as well as crack propagation resistance of geopolymer. For instance, minimum length of nanofillers to toughen this geopolymer at 250 °C was required as ~2 μm. The results further suggested that the sample failure occurred due to the dominance of tensile failure of nanofibers over the interfacial separation.     

Effect of disaccharide,gamma radiation and temperature on the physico-mechanical properties of jute fabrics reinforced unsaturated polyester resin-based composite

The jute fabrics reinforced unsaturated polyester resin (jute/UPR)-based composites were prepared successfully by the hand-lay-up technique. The percentage of jute fabrics was kept constant at 40% fiber (by weight). The disaccharide percentage was also kept constant at 2% (by weight), but at this percentage the mechanical properties were lower than the untreated composites. Gamma radiation dose was varied at 0, 2.5, 5 and 7.5?kGy for jute/UPR-based composites. At 5.0?kGy gamma dose highest TS, TM and Eb were obtained. The jute/UPR-based composites were treated under 30°C, 50°C and ?18°C for the measurement of mechanical properties. At low temperature (?18°C), the highest mechanical properties were observed. The water uptake properties were measured for disaccharide-treated and disaccharide-untreated composites up to 10 days, but no water was absorbed by the composites. The soil degradation test was carried out under 12 inch soil containing at least 25% water, but no significant decrease was observed for untreated and sucrose-treated composites. For the functional group analysis, FT-IR was carried out. For the fiber matrix adhesion analysis, the scanning electron microscopic image was taken.     

Fluorene-Based Poly(imino ketone) with Fluorine Atoms on the Side Chains as an Intelligent High-Performance Polymer

Abstract

Fluorene-based poly(imino ketone) with fluorine atoms in the side chains (PIKF-F), as an intelligent, high-performance polymer, was synthesized by the reaction of 4,4′-dibromobenzophenone and 9,9-bis(3-F-4-aminophenyl) fluorene via a palladium catalyzed C-N cross-coupling reaction. Its structure was characterized by means of FT-IR and ¹H NMR spectroscopy. The results showed a good agreement with the proposed structure. The molecular weights of the PIKF-F were measured by GPC (calibrated by polystyrene standards). The M_n and M_w values were 64,800 and 153,300, respectively. Thermogravimetric analysis and differential scanning calorimetry measurements showed that the polymer possessed good thermal stability with a high 10% decomposition temperature (450?°C) and a high glass transition temperature (T_g = 250?°C). The PIKF-F exhibited UV (ultra violet) absorption bands at 340–370?nm in NMP solution, while the fluorescence spectra showed maximum emission of PIKF-F at 498?nm in NMP solution. Both optical properties indicate the PIKF-F is of potential use as an organic photoelectric material. Additionally, due to its special conjugated system and the intramolecular hydrogen bonding (N–H···F), it was endowed with significantly strong photonic luminescence and the change of fluorescent intensity was reversible as the temperature was changed.