Self-assembled 3D Co3O4-graphene frameworks with high lithium storage performance

Three-dimensional Co₃O₄-graphene frameworks (3D-CGFs) are prepared with a one-pot hydrothermal method. Co₃O₄ particles are in situ anchored on graphene sheets, and the resulting composite self-assembles into 3D architecture during the hydrothermal treatment. Scanning electron microscope, transmission electron microscope, powder X-ray powder diffraction, and Raman spectroscopy are employed to characterize the sample. When tested as anode materials for lithium-ion batteries, 3D-CGFs demonstrate remarkable electrochemical lithium storage properties, such as large and stable reversible capacity (>530 mAh g^?1 at 500 mA g^?1 over 300 cycles), good capacity retention (88 % retention after 300 cycles at 500 mA g^?1 compared with the 4th cycle), excellent high-rate performance (515 mAh g^?1 at 1 A g^?1), making it a promising candidate for high-performance anode materials, especially for high-rate lithium-ion batteries.     

N-doped graphene/Bi nanocomposite with excellent electrochemical properties for lithium–ion batteries

N-doped graphene/Bi nanocomposite was prepared via a two-step method, combining the gas/liquid interface reaction with the rapid heat treatment method. The as-prepared sample was characterized by X-ray diffraction (XRD), field-emission scanning electron microscope (FESEM), X-ray photoelectron spectroscopy (XPS), and elemental analyzer. The XRD, FESEM, XPS, and elemental analysis results confirm the successful synthesis of N-doped graphene/Bi nanocomposite. As a result, the prepared N-doped graphene/Bi nanocomposite as an anode material for lithium-ion batteries delivers excellent electrochemical performance. A high lithium storage capacity of about 522 mAh g^?1 in the voltage range of 0.01–3.5 V is obtained. After 50 cycles at different current densities from 50 to 1000 mA g^?1, the specific capacity can still remain 386 mAh g^?1. Even at the high current density of 1000 mA g^?1, the N-doped graphene/Bi nanocomposite can still deliver a specific capacity of 218 mAh g^?1. The excellent electrochemical performance of the N-doped graphene/Bi nanocomposite is supposed to benefit from the high electronic conductivity of nitrogen-doped graphene and the synergistic effect of bismuth nanoparticles and nitrogen-doped graphene.     

Fabrication and electrochemical investigation of MWO<Subscript>4</Subscript> (M = Co,Ni) nanoparticles as high-performance anode materials for lithium-ion batteries

In this work, the MWO₄ (M = Co, Ni) nanoparticles were successfully synthesized by a facile one-step hydrothermal method and used as novel anode materials for LIBs. The micromorphology of obtained CoWO₄ and NiWO₄ was uniform nanoparticles with the size of ~60 and ~40 nm, respectively, by structural characterization including X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). When tested as lithium-ion battery anode, CoWO₄ nanoparticles exhibited a stabilized reversible capacity of 980 mA h g^?1 at 200 mA g^?1 after 120 cycles and 632 mA h g^?1 at 1000 mA g^?1 even after 400 cycles. And, the discharge capacity was as high as 550 mA h g^?1 at the 400th cycle for NiWO₄ nanoparticles. The excellent electrochemical performance could be attributed to the unique nanoparticles structure of the materials, which can not only shorten the diffusion length for electrons and lithium ions but also provide a large specific surface area for lithium storage.     

Synthesis and electrochemical performance of LiFePO<Subscript>4</Subscript>/C cathode materials from Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> for high-power lithium-ion batteries

Carbon-coated olivine-structured LiFePO₄/C composites are synthesized via an efficient and low-cost carbothermal reduction method using Fe₂O₃ as iron source at a relative low temperature (600 °C). The effects of two kinds of carbon sources, inorganic (acetylene black) and organic (sucrose), on the structures, morphologies, and lithium storage properties of LiFePO₄/C are evaluated in details. The particle size and distribution of the carbon-coated LiFePO₄ from sucrose (LiFePO₄/SUC) are more uniform than that obtained from acetylene black (LiFePO₄/AB). Moreover, the LiFePO₄/SUC nanocomposite shows superior electrochemical properties such as high discharge capacity of 156 mAh g^?1 at 0.1 C, excellent cyclic stability, and rate capability (78 mAh g^?1 at 20 C), as compared to LiFePO₄/AB. Cyclic voltammetric test discloses that the Li-ion diffusion, the reversibility of lithium extraction/insertion, and electrical conductivity are significantly improved in LiFePO₄/SUC composite. It is believed that olivine-structured LiFePO₄ decorated with carbon from organic carbon source (sucrose) using Fe₂O₃ is a promising cathode for high-power lithium-ion batteries.     

Synthesis and performance of Li2NiTi3O8 as a new anode material for lithium-ion batteries

The titanate spinel Li₂NiTi₃O₈ is proposed for the first time as a new anode for lithium-ion batteries and successfully synthesized via a facile ball-milling assisted solid-state reaction method. The sample is characterized by X-ray diffraction patterns (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM), galvanostatic charge–discharge tests, cyclic voltammetry (CV) tests, and electrochemical impedance spectroscopy (EIS). The results reveal that the Li₂NiTi₃O₈ nanoparticles have well-distributed morphology, and the particle size ranges between 100 and 300 nm. Although the initial coulombic efficiency is only 56.3 %, the Li₂NiTi₃O₈ electrode still exhibits a high rate capability and excellent cycling stability. The Li₂NiTi₃O₈ anode provides a large capacity of 212.3 mAh g^?1 at 0.1 A g^?1 after 10 cycle, which is close to its theoretical capacity (223.6 mAh g^?1). Even after 100 cycles, it still delivers a quite high capacity of 203.98 mAh g^?1, with no significant capacity fading. This indicates that the as-synthesized Li₂NiTi₃O₈ material is a promising anode material for lithium-ion batteries.     

Preparation and comparative structural properties of porous SnO2 microrods and submicrorods

A facile two-step approach has been used for the synthesis of porous SnO₂ rods: the initial room-temperature precipitation of precursor SnC₂O₄ and its subsequent thermal decomposition at 550 °C. Both the as-obtained porous SnO₂ microrods (length ～10.0?±?3.5 μm, diameter ～1.1?±?0.4 μm) and submicrorods (length ～5.8?±?1.9 μm, diameter ～0.4?±?0.1 μm) are the crystalline mixtures of major tetragonal and minor orthorhombic crystal phases, showing a tetragonal fraction of 84.7 and 87.0 %, respectively. When applied as a lithium-ion battery anode, the porous submicrorods (specific surface area ～13.6 m² g^?1) can deliver an initial discharge capacity of 1,730.7 mAh g^?1 with a high coulombic efficiency of 61.6 % and show the 50th discharge capacity of 662.8 mAh g^?1 at 160 mA g^?1 within a narrow potential range of 10.0 mV to 2.0 V. Similarly, even the anode of porous microrods (specific surface area ～11.8 m² g^?1) can still exhibit an initial discharge capacity of 1,661.1 mAh g^?1 at 160 mA g^?1 with a coulombic efficiency of 60.9 %. Regardless of the polymorphic nature, the acquired porosity may only alleviate the huge volume change of anodes for the first cycle; thus, the structural parameters of average size and specific surface area can be feasibly associated with the enhanced lithium storage capability. Anyway, these indicate a facile oxalate precursor method for the controlling synthesis and high performance of rodlike SnO₂ for lithium-ion batteries.     

S/N dual-doped carbon nanosheets decorated with Co<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>O<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript> nanoparticles as high-performance anodes for lithium-ion batteries

In this work, we have successfully synthesized the S/N dual-doped carbon nanosheets which are strongly coupled with Co _x O _y nanoparticles (SNCC) by calcinating cobalt/dithizone complex precursor following KOH activation. The SNCC as anode shows the wonderful charge capacity of 1200 mAh g^?1 after 400th cycles at 1000 mA g^?1 for Li-ion storage. The superior electrochemical properties illustrate that the SNCC can be a candidate for high-performance anode material of lithium-ion batteries (LIBs) because of the facile preparation method and excellent performance. Significantly, we also discuss the mechanism for the SNCC from the strong synergistic effect perspective.     

Preparation of Co<Subscript>3</Subscript>O<Subscript>4</Subscript> hollow microsphere/graphene/carbon nanotube flexible film as a binder-free anode material for lithium-ion batteries

A flexible Co₃O₄ hollow microsphere/graphene/carbon nanotube hybrid film is successfully prepared through a facile filtration strategy and a subsequent thermally treated process. The composition, morphology, and structure of the as-prepared film are characterized by X-ray diffraction, X-ray photoelectron spectrometer, scanning electron microscopy, and transmission electron microscopy. Based on the morphology characterizations on the hybrid film, the Co₃O₄ hollow microspheres are uniformly and closely attached on three-dimensional (3D) graphene/carbon nanotubes (GR/CNTs) network, which decreases the agglomeration of Co₃O₄ microspheres effectively. In this hybrid film, the 3D GR/CNT network which enhances conductance as well as prevents aggregation is a benefit to help Co₃O₄ to exert its lithium storage capabilities sufficiently. When used as a binder-free anode material for lithium-ion batteries, the hybrid film delivers excellent electrochemical properties involving reversible capacity (863 mAh g^?1 at a current density of 100 mA g^?1) and rate performance (185 mAh g^?1 at a current density of 1600 mA g^?1).     

Shape-controlled porous carbon from calcium citrate precursor and their intriguing application in lithium-ion batteries

Porous carbon nanosheets (PCNSs), porous carbon nanofibers (PCNFs), and flowerlike porous carbon microspheres (FPCMs) were successfully synthesized through a carbonization method combined with a simple acid pickling treatment using calcium citrate as the precursor. The as-prepared products show uniform morphologies, in which the FPCMs are self-assembled from PCNSs. As anodes of lithium-ion (Li-ion) batteries, these carbon materials deliver a stable reversible capacity above 515 mAh g^?1 after 50 cycles at 100 mA g^?1. Compared with PCNSs and PCNFs, FPCMs demonstrate preferable rate capability (378 mAh g^?1 at 1 A g^?1) and cyclability (643 mAh g^?1 at 100 mA g^?1). These results suggest that an appropriate select of morphology and structure will significantly improve the lithium storage capacity. The study also indicates that the novel shape-controlled porous carbon materials have potential applications as electrode materials in electronic devices.     

Anatase TiO<Subscript>2</Subscript> nanoparticles for lithium-ion batteries

Anatase TiO₂ nanoparticles were prepared by a simple sol-gel method at moderate temperature. X-ray powder diffraction (XRD) and Raman spectroscopy revealed the exclusive presence of anatase TiO₂ without impurities such as rutile or brookite TiO₂. Thermogravimetric analysis confirmed the formation of TiO₂ at about 400 °C. Particle size of about 20 nm observed by transmission electron microscopy matches well with the dimension of crystallites calculated from XRD. The electrochemical tests of the sol-gel-prepared anatase TiO₂ show promising results as electrode for lithium-ion batteries with a stable specific capacity of 174 mAh g^?1 after 30 cycles at C/10 rate. The results show that improvement of the electrochemical properties of TiO₂ to reach the performance required for use as an electrode for lithium-ion batteries requires not only nanosized porous particles but also a morphology that prevents the self-aggregation of the particles during cycling.     

Nitrogen-doped carbon nanofiber decorated LiFePO<Subscript>4</Subscript> composites with superior performance for lithium-ion batteries

Nitrogen-doped carbon nanofiber (NCNF) decorated LiFePO₄ (LFP) composites are synthesized via an in situ hydrothermal growth method. Electrochemical performance results show that the embedded NCNF can improve electron and ion transfer, thereby resulting in excellent cycling performance. The as-prepared LFP and NCNF composites exhibit excellent electrochemical properties with discharge capacities of 188.9 mAh g^?1 (at 0.2 C) maintained at 167.9 mAh g^?1 even after 200 charge/discharge cycles. The electrode also presents a good rate capability of 10 C and a reversible specific capacity as high as 95.7 mAh g^?1. LFP composites are a potential alternative high-performing anode material for lithium ion batteries.     

Synthesis and electrochemical investigation of highly dispersed ZnO nanoparticles as anode material for lithium-ion batteries

Highly dispersed ZnO nanoparticles were prepared by a versatile and scalable sol-gel synthetic technique. High-resolution transmission electronic microscopy (HRTEM) showed that the as-prepared ZnO nanoparticles are spherical in shape and exhibit a uniform particle size distribution with the average size of about 7 nm. Electrochemical properties of the resulting ZnO were evaluated by galvanostatic discharge/charge cycling as anode for lithium-ion battery. A reversible capacity of 1652 mAh g^?1 was delivered at the initial cycle and a capacity of 318 mAh g^?1 was remained after 100 cycles. Furthermore, the system could deliver a reversible capacity of 229 mAh g^?1 even at a high current density of 1.5 C. This outstanding electrochemical performance could be attributed to the nano-sized features of highly dispersed ZnO particles allowing for the better accommodation of large strains caused by particle expansion/shrinkage along with providing shorter diffusion paths for Li⁺ ions upon insertion/deinsertion.     

Cobalt imidazoledicarboxylate coordination complex microspheres: stable intercalation materials for lithium and sodium-ion batteries

A simple and versatile method for preparation of cobalt 4,5-imidazoledicarboxylate microspheres is developed. The cobalt 4,5-imidazoledicarboxylate complex is a kind of stable intercalation materials for lithium- and sodium-ion batteries. When tested as an anode material for lithium-ion batteries, the coordination complex microspheres based composite electrode delivers a second discharge capacity of 595.4 mAh g^?1 at a current density of 1 Ah g^?1. A reversible capacity of 416.1 mAh g^?1 remained after 143 cycles, while a reversible capacity of 259.9 mAh g^?1 remained after 500 cycles at a current density of 1.5 A g^?1. In addition, it can also serve as stable anode materials for sodium-ion batteries. Research based on the topics would shed some light on the discovery of new alternative intercalation materials to graphite.     

Three-dimensional carbon fiber as current collector for lithium/sulfur batteries

Ni foam and carbon fiber cloth were tested as three-dimensional (3D) current collectors for a sulfur/polypyrrole composite cathode in lithium batteries. The cell with the carbon fiber current collector has exhibited remarkably enhanced electrochemical performance compared with its Ni foam counterpart, delivering a high initial capacity of 1,278 mAh g^?1 and maintaining a discharge capacity at 810 mAh g^?1 after 40 cycles at 0.06 C. Furthermore, the carbon fiber-based cell demonstrated a better rate capability and delivered a highly reversible discharge capacity of 397 mAh g^?1 after 50 cycles at 0.5 C, representing an increase of 194 mAh g^?1 compared to the Ni foam counterpart. The electrochemical property investigations along with scanning electron microscope studies have revealed that the carbon fiber current collector possesses a three-dimensional network structure, provides an effective electron conduction path, and minimizes the loss of electrical contact within the deposited cathode material during cycling. These results indicate that the carbon fiber cloth can be used as a promising, effective, and inexpensive current collector for Li/S batteries.     

Simple microwave synthesis and improved electrochemical performance of Nb-doped MnO<Subscript>2</Subscript>/reduced graphene oxide composite as anode material for lithium-ion batteries

Niobium-doped MnO₂/reduced graphene oxide (Nb-MnO₂/RGO) composite has been successfully synthesized via a simple microwave radiation method. The samples were systematically studied by X-ray diffraction (XRD), thermogravimetric analysis (TG), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), transmission electron microscope (TEM), and electrochemical measurements. As the anode material for lithium-ion batteries, the Nb-MnO₂/RGO (molar ratio of Mn/Nb?=?50:1) (NMG50) showed an outstanding reversible discharge capacity of 556.6 mAh g^?1 after 50 cycles with a capacity retention of 77% at a charge-discharge rate of 0.1 A g^?1 and the reversible discharge capacity can still retain 223.3 mAh g^?1 at a current of 1 A g^?1, which is much higher than those for Nb-MnO₂/RGO (molar ratio of Mn/Nb?=?10:1) (NMG10) and undoped MnO₂/RGO (MG). The improved electrochemical performance could be attributed to the proper amount of Nb doping, which could enhance both the conductivity and the structure stability of MnO₂.     

Hierarchical Co<Subscript>3</Subscript>O<Subscript>4</Subscript>@C hollow microspheres with high capacity as an anode material for lithium-ion batteries

Three-dimensional hierarchical Co₃O₄@C hollow microspheres (Co₃O₄@C HSs) are successfully fabricated by a facile and scalable method. The Co₃O₄@C HSs are composed of numerous Co₃O₄ nanoparticles uniformly coated by a thin layer of carbon. Due to its stable 3D hierarchical hollow structure and uniform carbon coating, the Co₃O₄@C HSs exhibit excellent electrochemical performance as an anode material for lithium-ion batteries (LIBs). The Co₃O₄@C HSs electrode delivers a high reversible specific capacity, excellent cycling stability (1672 mAh g^?1 after 100 cycles at 0.2 A g^?1 and 842.7 mAh g^?1 after 600 cycles at 1 A g^?1), and prominent rate performance (580.9 mAh g^?1 at 5 A g^?1). The excellent electrochemical performance makes this 3D hierarchical Co₃O₄@C HS a potential candidate for the anode materials of the next-generation LIBs. In addition, this simple synthetic strategy should also be applicable for synthesizing other 3D hierarchical metal oxide/C composites for energy storage and conversion.     

Facial synthesis of carbon-coated ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/graphene and their enhanced lithium storage properties

Carbon-coated ZnFe₂O₄ spheres with sizes of ~110–180 nm anchored on graphene nanosheets (ZF@C/G) are successfully prepared and applied as anode materials for lithium ion batteries (LIBs). The obtained ZF@C/G presents an initial discharge capacity of 1235 mAh g^?1 and maintains a reversible capacity of 775 mAh g^?1 after 150 cycles at a current density of 500 mA g^?1. After being tested at 2 A g^?1 for 700 cycles, the capacity still retains 617 mAh g^?1. The enhanced electrochemical performances can be attributed to the synergetic role of graphene and uniform carbon coating (~3–6 nm), which can inhibit the volume expansion, prevent the pulverization/aggregation upon prolonged cycling, and facilitate the electron transfer between carbon-coated ZnFe₂O₄ spheres. The electrochemical results suggest that the synthesized ZF@C/G nanostructures are promising electrode materials for high-performance lithium ion batteries.

Open image in new window

Graphical abstract ?

     

Influence of post-calcination treatment on the spinel lithium titanium oxide anode material for lithium ion batteries

The influence of post-calcination treatment on spinel Li₄Ti₅O₁₂ anode material is extensively studied combining with a ball-milling-assisted rheological phase reaction method. The post-calcinated Li₄Ti₅O₁₂ shows a well distribution with expanded gaps between particles, which are beneficial for lithium ion mobility. Electrochemical results exhibit that the post-calcinated Li₄Ti₅O₁₂ delivers an improved specific capacity and rate capability. A high discharge capacity of 172.9 mAh g^?1 and a reversible charge capacity of 171.1 mAh g^?1 can be achieved at 1 C rate, which are very close to its theoretical capacity (175 mAh g^?1). Even at the rate of 20 C, the post-calcinated Li₄Ti₅O₁₂ still delivers a quite high charge capacity of 124.5 mAh g^?1 after 50 cycles, which is much improved over that (43.9 mAh g^?1) of the pure Li₄Ti₅O₁₂ without post-calcination treatment. This excellent electrochemical performance should be ascribed to the post-calcination process, which can greatly improve the lithium ion diffusion coefficient and further enhance the electrochemical kinetics significantly.     

Advanced LiTi<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C anode by incorporation of carbon nanotubes for aqueous lithium-ion batteries

Inferior rate capability is a big challenge for LiTi₂(PO₄)₃ anode for aqueous lithium-ion batteries. Herein, to address such issue, we synthesized a high-performance LiTi₂(PO₄)₃/carbon/carbon nanotube (LTP/C/CNT) composite by virtue of high-quality carbon coating and incorporation of good conductive network. The as-prepared LTP/C/CNT composite exhibits excellent rate performance with discharge capacity of 80.1 and 59.1 mAh g^?1 at 10 C and 20 C (based on the mass of anode, 1 C = 150 mA g^?1), much larger than that of the LTP/C composite (53.4 mAh g^?1 at 10 C, and 31.7 mAh g^?1 at 20 C). LTP/C/CNT also demonstrates outstanding cycling stability with capacity retention of 83.3 % after 1000 cycles at 5 C, superior to LTP/C without incorporation of CNTs (60.1 %). As verified, the excellent electrochemical performance of the LTP/C/CNT composite is attributed to the enhanced electrical conductivity, rapid charge transfer, and Li-ion diffusion because of the incorporation of CNTs.     

Urea-assisted solvothermal synthesis of monodisperse multiporous hierarchical micro/nanostructured ZnCo<Subscript>2</Subscript>O<Subscript>4</Subscript> microspheres and their lithium storage properties

High-quality monodisperse multiporous hierarchical micro/nanostructured ZnCo₂O₄ microspheres have been fabricated by calcinating the Zn_1/3Co_2/3CO₃ precursor prepared by urea-assisted solvothermal method. The as-prepared products are characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HRTEM), and Brunauer-Emmett-Teller (BET) measurement to study the crystal phase and morphology. When tested as anode material for lithium ion batteries, the multiporous ZnCo₂O₄ microspheres exhibit an initial discharge capacity of 1,369 mAh g^?1 (3,244.5 F cm^?3) and retain stable capacity of 800 mAh g^?1 (1,896 F cm^?3) after 30 cycles. It should be noted that the good electrochemical performances can be attributed to the porous structure composed of interconnected nanoscale particles, which can promote electrolyte diffusion and reduce volume change during discharge/charge processes. More importantly, this ZnCo₂O₄ 3D hierarchical structures provide a large number of active surface position for Li⁺ diffusion, which may contribute to the improved electrochemical performance towards lithium storage.