High-power intracavity frequency doubling of a Ti:sapphire femtosecond oscillator

We demonstrate intracavity frequency doubling of a standard femtosecond Ti:sapphire oscillator. The cavity is extended with a pair of focusing mirrors and a 0.5-mm-thick BBO crystal. We achieve a repetition rate of 50 MHz and simultaneously generate 22 mW of 55-fs pulses at 810 nm and 200 mW of 73-fs pulses at 405 nm, which corresponds to 4 nJ per pulse. We create a total of 330-mW, 405-nm light when pumping the Ti:sapphire crystal with 5.7 W from an Ar-ion laser, corresponding to a conversion efficiency of 5.7%. No saturation is found, which implies that higher outputs can be achieved with higher pump rates. Preliminary results from the use of blue pulses as pump in an optical parametric amplifier seeded by pulses from a photonic crystal fiber are presented. Received: 27 January 2003 / Revised version: 27 March 2003 / Published online: 12 May 2003 RID="*" ID="*"Corresponding author. Fax: +45-861/96199, E-mail: tva@chem.au.dk     

A compact frequency-doubled 10-kHz PRF copper-vapour-laser-pumped dye laser

A 10-kHz pulse-repetition-frequency dye-laser master-oscillator power amplifier, end-pumped by a copper vapour laser (CVL), is reported. This laser was based on recently available, lightweight and compact CVL and dye laser components. Dye laser tunability was achieved from 592 to 622 nm and, when the oscillator was etalon line-narrowed, up to 1.5 W of single-etalon-mode output was obtained from the amplifier at the 608-nm peak tuning wavelength. By frequency doubling this amplified output in a BBO crystal we obtained up to 225 mW of 5-GHz 308-nm output, which is suitable for the performance of tropospheric hydroxyl radical concentration measurements. Received: 16 July 2002 / Revised version: 6 November 2002 / Published online: 5 February 2003 RID="*" ID="*"Present address: Department of Geography, University of Cambridge, Cambridge, CB2 3EN, UK RID="**" ID="**"Corresponding author. Fax: +44-1865/272400, E-mail: d.coutts1@physics.ox.ac.uk     

A 7-W diode-pumped Nd:YVO4 cw laser at 1.34 μm

A Nd:YVO₄ laser, end-pumped by a fiber-coupled diode-laser array, generates 7.3 W of output power at 1342 nm, the highest so far reported for this host crystal. The slope efficiency is 40% and the output-beam divergence is close to the diffraction limit. An important point in attaining such results is the choice of crystals with low Nd concentration. Received: 16 July 2002 / Published online: 25 October 2002 RID="*" ID="*"Corresponding author. Fax: +39-050/844333, E-mail: dilieto@df.unipi.it RID="**" ID="**"Permanent address: Scuola Normale Superiore, Piazza dei Cavalieri 7, Pisa, Italy     

Studies of high-repetition-rate laser plasma EUV sources from droplet targets

The water droplet laser plasma source has been shown to have many attractive features as a continuous, almost debris-free source for extreme ultraviolet (EUV) and X-ray applications. Through a dual experimental and theoretical study, we analyze the interaction physics between the laser light and the target. The hydrodynamic laser plasma simulation code, Medusa103 is used to model the electron density distribution for comparison to electron density distributions obtained through Abel inversion of plasma interferograms. In addition, flat field EUV spectra are compared to synthetic spectra calculated with the atomic physics code RATION. Received: 31 October 2002 / Accepted: 8 February 2003 / Published online: 28 May 2003 RID="*" ID="*"Present address: Naval Reseach Laboratory, Washington D.C. RID="**" ID="**"Present address: Xtreme Technologies, G?ttingen, Germany. RID="***" ID="***"Corresponding author. Fax: +1-407/823-3570, E-mail: mrichard@mail.ucf.edu     

A high-sensitivity in situ optical diagnostic technique for laser cleaning of transparent substrates

A differential optical transmission technique has been used to monitor in situ the efficiency of laser cleaning for the removal of sub-micrometer-sized particles on substrates transparent at the monitoring wavelength. This technique has been applied to the removal of sub-micrometer polystyrene particles on polyimide substrates using laser pulses of 30 ps duration at 292 nm while probing the material transmission at 633 nm. The sensitivity achieved -1/10⁴ for the transmission changes induced upon single-pulse laser exposure – allows us to monitor the removal of just a few sub-micron-sized particles from the probed region inside the irradiated area. Received: 2 October 2002 / Accepted: 7 October 2002 / Published online: 29 January 2003 RID="*" ID="*"Corresponding author. Fax: +33-3/87844082, E-mail: nchaoui@iut.univ-metz.fr RID="**" ID="**"Present address: Laboratoire de Chimie et Applications, Institut Universitaire de Technologie de Metz, Département Chimie, Rue Victor Demange, 57500 Saint-Avold, France     

Removal of oxygen atoms from a SiO2 surface by incoherent vacuum ultraviolet excimer irradiation

We have demonstrated the non-thermal removal of oxygen atoms from an oxidized silicon surface (SiO₂) on a silicon wafer by the use of a low-power (0.3 mW cm^-2) incoherent vacuum ultraviolet (VUV) light source at 126 nm. X-ray photoelectron spectroscopy (XPS) has shown that a maximum Si concentration of 80% appears at the surface after a 20-h irradiation with 9.8 eV photons, as a result of oxygen removal from the SiO₂ matrix. The surface morphology, however, indicates no damage or melting on the surface even after the irradiation. Received: 15 April 2002 / Accepted: 17 April 2002 / Published online: 10 September 2002 RID="*" ID="*"Permanent address: Nano-Tech Photon Inc., Shimotomita 4132-1, Shintomi, Miyazaki, 889-1404, Japan RID="**" ID="**"Corresponding author. Fax: +81-985/583-899, E-mail: kubodera@opt.miyazaki-u.jp     

Generation of 99-mW continuous-wave 285-nm radiation for magneto-optical trapping of Mg atoms

We have developed a tunable intense narrow-band 285 nm light source based on frequency doubling of 570 nm light in BBO. At input powers of 840 mW (including 130 mW used for locking purposes) we generate 99 mW UV radiation with an intensity profile suitable for laser-cooling experiments. The light is used for laser cooling of neutral magnesium atoms in a magneto-optical trap (MOT). We capture about 5×10⁶ atoms directly from a thermal beam and find that the major loss mechanism of the magnesium MOT is a near-resonant two-photon ionization process. Received: 15 February 2002 / Revised version: 13 August 2002 / Published online: 11 December 2002 RID="*" ID="*"Corresponding author. Fax: +45-4588/7762, E-mail: dnm@mic.dtu.dk Present address: Mikroelektronik Centret, Technical University of Denmark, Orsteds Plads, Bldg. 345 East, 2800 Kgs. Lyngby, Denmark     

The application of quasi-phase-matched parametric light sources to practical infrared chemical sensing systems

Quasi-phase-matched (QPM) materials allow the generation of spectroscopically useful infrared radiation in an efficient and broadly tunable format. Here, we describe several applications of QPM-based light sources to remote and local chemical sensing. The remote systems are gas imagers that employ a fiber-pumped continuous-wave optical parametric oscillator or a microlaser-pumped, diode-seeded optical parametric amplifier as the illumination source. Technology described for local sensing includes a cavity ring down spectrometer that employs a novel optical parametric generator–amplifier to achieve ≥350 cm^-1 of contiguous tuning and a long-wave infrared light source based on QPM GaAs. In each case the use of QPM materials in conjunction with effective pump sources instills simplicity and ruggedness into the sensing systems. Received: 15 April 2002 / Revised version: 6 June 2002 / Published online: 12 September 2002 RID="*" ID="*"Corresponding author. Fax: +1-925/294-2595, E-mail: tjkulp@sandia.gov RID="**" ID="**"Present address: Corning Inc., Corning, NY 14831, USA RID="*" ID="*"Present address: Corning Inc., Corning, NY 14831, USA RID="**" ID="**"Present address: Blue Leaf Networks, Sunnyvale, CA 94086, USA RID="***" ID="***"Present address: Sandia National Laboratories, Albuquerque, NM 87185, USA     

Fundamentals and advantages of ultrafast micro-structuring of transparent materials

Experimental investigations using femtosecond and picosecond laser pulses at 800 nm illuminate the distinctions between the dynamics and nature of ultrafast processing of dielectrics compared with semiconductors and metals. Dielectric materials are strongly charged at the surface on the sub-ps time scale and undergo an impulsive Coulomb explosion prior to thermal ablation. Provided the laser pulse width remains in the ps or sub-ps time domain, this effect can be exploited for processing. In the case of thermal ablation alone, the high localization of energy accompanied by ultrafast laser micro-structuring is of great advantage also for high quality processing of thin metallic or semiconducting layers, in which the surface charge is effectively quenched. Received: 17 January 2003 / Accepted: 8 February 2003 / Published online: 28 May 2003 RID="*" ID="*"Corresponding author. Fax: +49-30/670-53-500, E-mail: d.ashkenasi@lmtb.dt RID="**" ID="**"Present address: LMTB GmbH, Berlin, Fabeckstr. 60–62, D-14195 Berlin, Germany     

Novel technique for the measurement of fiber dispersion properties

We present a novel method for measuring the linear and nonlinear dispersion properties of conventional and micro-structured fibers. It is based on the automated compensation of phase modulations using a high-resolution pulse-shaping device. No tunable laser source is required. Received: 20 December 2002 / Published online: 19 March 2003 RID="*" ID="*"Corresponding author. Fax: +49-3641/947202, E-mail: stobrawa@ioq.uni-jena.de RID="**" ID="**"Present address: Carl Zeiss Meditec AG, G?schwitzer Strasse 51–52, 07745 Jena, Germany     

Amplification and wave mixing of induced and spontaneous emission in semiconductor laser amplifiers

We theoretically describe and experimentally investigate the spatio-spectral wave mixing of induced and spontaneous emission in large-area InGaAs-semiconductor laser amplifiers. The dynamic light-matter-coupling is described by a spatially resolved theory based on Maxwell–Bloch–Langevin equations, taking into account many-body-carrier interactions, energy transfer between the carrier and phonon systems and, in particular, the spatio-temporal interplay of stimulated and amplified spontaneous emission and the noise caused by spontaneous emission. Our numerical model reveals the fundamental physical processes which are responsible for the spectral power distribution of the amplified laser light and predicts the emission properties of high-power semiconductor laser amplifiers, such as emission spectra and input power–output power characteristics. Received:30October2002/Revisedversion:21November2002 / Published online: 12 February 2003 RID="*" ID="*"Corresponding author. Fax: +49-711/6862-349, E-mail: Edeltraud.Gehrig@dlr.de RID="**" ID="**"Also at: Institute of Physics, Tampere University of Technology, P.O. Box 692, FIN-33101, Tampere, Finland RID="***" ID="***"Present address: Heidelberger Druckmaschinen AG, Speyerer Strasse 6, 69115 Heidelberg, Germany RID="****" ID="****"Present address: Lightbit Corporation, 411 Clyde Avenue, Mountain View, CA 94043, USA     

Transmission and scanning electron microscopy studies of single femtosecond- laser-pulse ablation of silicon

The final state of the material resulting from laser irradiation of silicon using 130 fs pulses at 790 nm was studied using a number of techniques including scanning and transmission electron microscopies, as well as atomic force microscopy. Structural details and the level of damage to the nearby solid following irradiation were characterized and are discussed in the context of recent dynamical studies. Received: 28 September 2001 / Accepted: 3 March 2002 / Published online: 19 July 2002 RID="*" ID="*"Department of Engineering Physics, McMaster University, Hamilton, Ontario, L8S 4M1, Canada RID="**" ID="**"Corresponding author. Fax: +1-905/521-2773, E-mail: borowia@mcmaster.ca RID="***" ID="***"Present address: Department of Physics and Astronomy, University of Glasgow, Glasgow, G12 8QQ, UK RID="****" ID="****"Department of Materials Science and the CEMD, McMaster University, Hamilton, Ontario, L8S 4M1, Canada RID="*****" ID="*****"Departments of Engineering Physics, and Physics and Astronomy, and the CEMD, McMaster University, Hamilton, Ontario, L8S 4M1, Canada     

Photoinduced macroscopic chiral structures in a series of azobenzene copolyesters

A study of the propagation of elliptically polarized light and the resulting formation of macroscopic chiral structures in a series of azobenzene side-chain copolyesters, in which the morphology is varied from liquid crystalline to amorphous, is reported. Real-time measurements are presented, showing the dynamic behavior of the photoinduced rotation of the polarization ellipse in the different samples. The relationship between the ellipticity of the recording light and the linear birefringence induced is studied. A numerical solution that takes into account the influence of the photoinduced linear dichroism on the light propagation through the samples is presented. Received: 10 June 2002 / Revised version: 26 July 2002 / Published online: 15 November 2002 RID="*" ID="*"Corresponding author. Fax: +45-4677/4588, E-mail: lian.nedelchev@risoe.dk RID="**" ID="**"Permanent address: Department of Chemistry and Physics, The Nottingham Trent Unversity, Clifton Lane, Nottingham NG11 8NS, England     

All-reflective interferometric autocorrelator for the measurement of ultra-short optical pulses

We have developed a novel interferometric autocorrelator composed of only reflective elements, which functions as a beam splitter and an optical delay line. Analytical expressions are derived to give second-order autocorrelation functions and deconvolution factors for various conditions. The measurement of femtosecond laser pulses by interferometric autocorrelation is demonstrated in the visible region. The results are compared with those by calculation. Received: 9 December 2002 Revised version: 18 February 2003 / Published online: 5 May 2003 RID="*" ID="*"Present address: Department of Physics, Tokai University, 1117 Kitakaname, Hiratsuka, Kanagawa 259-1207, Japan RID="**" ID="**"Corresponding author. Fax: +81-48/462-4682, E-mail: asuda@postman.riken.go.jp     

High-repetition-rate eye-safe optical parametric oscillator intracavity pumped by a diode-pumped Q-switched Nd:YVO<Subscript>4</Subscript> laser

A high-repetition-rate eye-safe optical parametric oscillator (OPO), using a non-critically phase-matched KTP crystal intracavity pumped by an acousto-optically (AO) Q-switchedNd:YVO₄ laser, is experimentally demonstrated. It is found that the average OPO signal power at 1573 nm can be efficiently increased by increasing the pulse repetition rate. Moreover, the intracavity OPO process effectively shortens the pulse width so that it is in the range 5∼8 ns for pulse repetition rates of 10 to 80 kHz. As a result of the relatively short pulse, the peak power at 1573 nm is higher than 2 kW at a pulse repetition rate of 80 kHz. Received: 10 July 2002 / Published online: 26 February 2003 RID="*" ID="*"Corresponding author. Fax: +886-35/729-134, E-mail: yfchen@cc.nctu.edu.tw     

Impulse-scaling in a laser-driven in-tube accelerator

The laser-driven in-tube accelerator (LITA) is a unique device for laser propulsion. It is characterized by the acceleration of a projectile in a tube. The thrust performance can be improved by exploiting a confinement effect. In the experiment, a 3.0-g projectile is vertically launched, and the momentum coupling coefficient is measured for various monoatomic gases. The measured coupling coefficient is almost proportional to the reciprocal of the speed of sound. The same impulse generation characteristics are obtained in simplified situations that are analyzed based on conservation relations. Received: 26 August 2002 / Accepted: 8 February 2003 / Published online: 28 May 2003 RID="*" ID="*"Corresponding author. Fax: +81-22/217-5284, E-Mail: sasoh@ifs.tohoku.ac.jp RID="**" ID="**"Present address: also at Institute of Advanced Aerospace Technology, Seoul National University, Seoul, 151-742, Korea     

Dynamic temporal pulse shaping in advanced ultrafast laser material processing

Phase-manipulated ultrafast laser pulses and temporally tailored pulse trains with THz repetition rates are promising new tools for quality micromachining of brittle dielectrics, allowing to adapt the laser energy delivery rate to the material properties for optimal processing. Different materials respond with specific reaction pathways to the sudden energy input depending on the efficiency of electron generation and on the ability to release the energy into the lattice. The sequential energy delivery with judiciously chosen pulse trains may induce softening of the material during the initial steps of excitation and change the energy coupling for the subsequent steps. We show that this can result in lower stress, cleaner structures, and allow for a material-dependent optimization process. Received: 7 October 2002 / Accepted: 20 January 2003 / Published online: 28 May 2003 RID="*" ID="*"Corresponding author. Fax: +49-30/6392-1229, E-mail: stoian@mbi-berlin.de RID="**" ID="**"Now at Katana Technologies GmbH, Albert-Einstein-Ring 7, 14532 Kleinmachnow, Germany     

Bulk heating of transparent materials using a high-repetition-rate femtosecond laser

Femtosecond laser pulses can locally induce structural and chemical changes in the bulk of transparent materials, opening the door to the three-dimensional fabrication of optical devices. We review the laser and focusing parameters that have been applied to induce these changes and discuss the different physical mechanisms that play a role in forming them. We then describe a new technique for inducing refractive-index changes in bulk material using a high-repetition-rate femtosecond oscillator. The changes are caused by a localized melting of the material, which results from an accumulation of thermal energy due to nonlinear absorption of the high-repetition-rate train of laser pulses. Received: 21 November 2001 / Accepted: 9 July 2002 / Published online: 25 October 2002 RID="*" ID="*"Corresponding author. Fax: +1-858/534-7697, E-mail: cschaffer@ucsd.edu RID="**" ID="**"Current address: University of California, San Diego, Department of Physics, La Jolla, CA 92 093, USA     

Characterization of laser-ablated and chemically reduced silver colloids in aqueous solution by UV/VIS spectroscopy and STM/SEM microscopy

Silver colloids in aqueous solution were studied by different scanning microscopy techniques and UV/VIS spectroscopy. The silver colloids were produced either by chemical reduction or by nanosecond laser ablation from a solid silver foil in water. Variation of laser power and ablation time leads to solutions of metal clusters of different sizes in water. We characterized the electronic absorption of the clusters by UV/VIS spectroscopy. STM (scanning tunneling microscope) imaging of the metal colloids shows atomic resolution of rod- or tenon-like silver clusters up to 10-nm length formed by laser ablation. Our scanning electron microscope measurements, however, show that much larger silver colloids up to 5-μm length are also formed, which are not visible in the STM due to their roughness. We correlate them with the long-wavelength tail of the multimodal UV/VIS spectrum. The silver colloids obtained by chemical reduction are generally larger and their electronic spectra are red-shifted compared to the laser-ablated clusters. Irradiation of the colloid solution with nanosecond laser pulses of appropriate fluence at 532 nm and 355 nm initially reduced the colloid size. Longer irradiation at 355 nm, however, leads to the formation of larger colloids again. There seems to be a critical lower particle size, where silver clusters in aqueous solution become unstable and start to coagulate. Received: 24 June 2002 / Revised version: 25 July 2002 / Published online: 25 October 2002 RID="*" ID="*"This work is part of the thesis of H. M?ltgen RID="**" ID="**"Corresponding author. Fax: +49-211/811-5195, E-mail: kleinermanns@uni-duesseldorf.de     

Sub-nanosecond microchip laser with intracavity Raman conversion

Efficient sub-nanosecond pulse operation of microchip lasers with intracavity Raman conversion and pulse compression is presented for the first time. The microchip lasers were composed of Nd:LSB or Nd:YAG laser crystals, Cr⁴⁺:YAG saturable absorber, and Ba(NO₃)₂ Raman medium. The pulse duration obtained at the Stokes wavelength (1196 nm) was as short as 118 ps. Optical conversion efficiency of laser-diode pump power to the Stokes power of 8% was reached. Pulse energy and peak power of Stokes emission were 1.2 μJ and 5.4 kW, correspondingly. Numerical calculations are in good agreement with obtained experimental results. Received: 20 December 2002 / Revised version: 6 March 2003 / Published online: 5 May 2003 RID="*" ID="*"Corresponding author. Fax: +1-716/645-6945, E-mail: ankuzmin@acsu.buffalo.edu RID="**" ID="**"Present address: University at Buffalo, SUNY, The Institute for Lasers, Photonics, and Biophotonics, 458 NSC, Buffalo, NY 14 260-3000, USA